8mm FRAMELESS CONCEALED HINGE DOOR

Transcription

1 8mm FRAMELESS CONCEALED HINGE DOOR Refer To Sheet For Relevant Product Codes Decide which hand is required. Right hand opening illustrated. Change the hand by turning the fixed panel upside down. The moving panel turning inside and outside. VictoriaPlum.com

2 BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION ) General Information Please inspect this product upon delivery, any missing parts or manufacturing defects must be reported immediately to the supplier. Damage or defects reported later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE. Glass breakage claims will not be accepted after the product has been unpacked. Please note: Aluminium is a soft metal, and undergoes a series of extrusion, fabrication, polishing and anodising processes in order to create your finished shower enclosure. Some light surface marks are normal, and is a result of the manufacturing processes. Quality control has ensured that this item is of a good standard, and is fit for purpose. ) Additional Notes Please read these instructions carefully before starting installation. Special care should be taken when drilling walls to avoid hidden pipes or electrical cables. Note: this product is heavy and may require two people to install. TOOLS REQUIRED DESCRIPTION PART IMAGE DESCRIPTION PART IMAGE Tape measure Drill Spirit level Flat-head Screwdriver Pencil Cross head Screwdriver PZ Ø6mm Drill bit Mallet Ømm Drill bit Silicone Sealant This product is heavy and may require two people to install.

3 ASSEMBLY INSTRUCTIONS - DRAWING () () (0) (9) (8) (7) (6) () () () (4) (5) (6) (7) (8) (9) (5) (4) () (0) () () ()(4)(5)(6) (7) (8) (9) (0) () () Packed in moving panel carton: () x Magnet profile top cap () x Magnet wall profile top cap L&R () 4x Screws 4x0 (4) x Magnet wall profile (5) x Magnet profile (6) x Magnet seal (7) x Handle (supplied separately) (8) x Screw caps (9) x Moving panel (0) 4x Wall plugs () x Screws 4x () x Bottom strip caps A L&R () x Bottom drip strip (4) x Bottom seal (5) x Support block (6) x Bottom strip caps B L&R (7) x Moving Panel Seal Packed in fixed panel carton: (8) x Fixed Panel Seal (9) x Hinges (0) x Fixed panel () x Wall profile cover strip () x Wall profile () 6x Wall plugs (4) 6x Screws 4x0 (5) x Screws 4x (6) x Glass clamp (7) x Top bar A (8) x T piece corner bracket (9) x Wall profile top cap (0) x Upright profile top cap () x Wall bracket () x Top bar B

4 ASSEMBLY INSTRUCTIONS If you require help, we advise you to contact a competent plumber Installation Steps THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 0mm TILE/WET WALL PANEL. FITTED RECESS DOOR DRAWING /000/00/ /000/0/

5 Step SLIDE WALL PROFILE ON TO FIXED PANEL Step MARK WALL FIXING POSITIONS 0mm 0mm 4

6 Step DRILLING WALL PROFILE TO THE WALL + FITTING FIXED PANEL x4 6.0mm x4 x4 St4x0 Step 4 ASSEMBLING THE HINGES + MOVING PANEL 5

7 Step 5 FITTING THE SEALS IF YOU ARE ASSEMBLING WITH A SIDE PANEL - PLEASE NOW ASSEMBLY INSTRUCTIONS IN THE SIDE PANEL BOX. 4 5 CONTINUE USING THE 4 mm 5 5mm Step 6 INSTALLING THE MAGNET PROFILE 4 x4 x4 5 x4 x4 6.0mm St4x0 6

8 Step 7 SECURING THE WALL PROFILES + COVER STRIP Take care not to drill to the glass L=0~0mm L 5mm/R 0mm L 5mm/R 5mm x R x 4.0mm x x.0mm 5 ST4X x x 6 ST4X Step 8 FITTING THE TOP BAR WALL BRACKETS + T PIECE BAR x 4 x 50mm 50mm 6.0mm 5 x 50~00mm x 6 x ST4X0 7

9 Step 9 INSTALLING THE TOP BAR L L-7mm x 6 8

10 Step 0 FITTING THE BOTTOM DRIP STRIP 4 9

11 Step FITTING THE TOP CAPS AND HANDLE Step SILICONE THE OUTSIDE EDGES 4 hours Allow 4 hours for silicone to dry before use. Silicone on the outside edge only, NOT THE INSIDE 0

12 CARE AND MAINTENANCE ) AFTER CARE INSTRUCTIONS Regularly clean your shower product with warm soapy water to prevent lime scale build up. Do not use abrasive cleaning fluids or materials, or strong chemical cleaners as this will damage the product surface. ) MAINTENANCE Clean the plastic parts with a cloth and mild detergent. Never use any abrasive creams, dissolvents, acetone or detergents and disinfectants that contain chlorine. The supplier accepts no liability for any type of use of care other than those contained in these instructions. The supplier reserves the right to introduce technical changes without notice. COMMITMENT TO QUALITY It is our intention that the quality and functions of this product are of the highest standard. If you require help we advise you firstly contact a competent plumber. However we understand that this may not always be the case, so should you experience any problems please contact our customer services quoting the following: Product name: 8mm Frameless Conceal Hinge Door Product code: LHD90A / LHD00A / LHD0A / LHD40A / LHD90B Customer help line number:

13 INSTALLERS NOTES

14 INSTALLERS NOTES

15 INSTALLERS NOTES 4

16 Victoria Plum Limited, Bridgehead Business Park Hessle, HU 0DG 6 EN 448:004+A:008 DOP No.:J Shower enclosures with aluminium profiles and safety glass Essential characteristics Cleanability Impact resistance/shatter properties Durability Performance Pass Pass Pass Harmonised technical specification Clause 4. of EN 448:004+A: 008 Clause 4. of EN 448:004+A: 008 Clause 4.4 of EN 448:004+A: 008 The packaging you have received with your product is 00% recyclable. It must be disposed of in a safe and environmentally friendly way. We suggest you take it to the local landfill site and discard in the designated bins. V0// 06