premium click optimum click
|
|
- Damian Jordan
- 5 years ago
- Views:
Transcription
1 5 golden rules Install your floor between 18 and 30 C. 48h Pergo Vinyl must be acclimatized in the room of installation between (64-86 F) for a period of at least 48 hours before installation. This floor & room temperature needs to be maintained prior to, during and for at least 24 hours after the installation is completed Use a special underlay above 45. Recommended PERGO sunsafe underlay > 45 Recommended PERGO basic underlay < 45 Pergo Vinyl has been designed for indoor heated (> 0) (32 F) installations. It cannot be installed in solariums, seasonal porches, camping trailers, boats or unheated applications without being glued. If the temperature of your floor raises above 45 (113 F), for instance due to direct sunlight, it is recommended to use the Sun/Heat underlay or to install without underlay on a levelled mineral subfloor. If you have any concerns about the temperature of your floor, please contact the Pergo technical department. Click-it! Never use a hammer or tapping block. Slightly lift the plank to be installed by holding your hand underneath. Push the short side joint down gently with your thumb moving from the inner corner towards the outside until you hear a click. Ensure the short side ends are closed by knocking gently on the short side click connection with your wrist. Don t use a hammer or tapping block as it may possible harm your click connection. This is the easiest method for fitting the Uniclic Multifit for Vinyl click panels. Keep indoor climate conditions above 0. Ensure that the indoor climate conditions are always kept > 0 (32 F) and preferably between (64-86 F). > 0 Make sure that you leave an expansion joint of minimum 2 mm. >2 mm InstallationInfo_VinylClick_ENG.indd 1 8/08/ :25:38
2 Preparation We recommend to order all panels for a commercial flooring project at the same time. Always store and transport Pergo Vinyl carefully to prevent distortions. Store and transport the boxes on a flat surface in neat stacks. Never store the boxes upright or in moist, dusty rooms or places with extreme temperatures. Pergo Vinyl must be acclimatized in the room of installation between (64-86 F) for a period of at least 48 hours before installation. This floor & room temperature needs to be maintained prior to, during and for at least 24 hours after the installation is completed. 48h The type of subfloor, its quality and its preparation have a big influence on the final installation result. If the subfloor is not appropriate for the installation of Pergo Vinyl then necessary actions should be taken. Contact your Pergo Vinyl dealer, who will be more than happy to help you. Be aware that unevennesses in the subfloor may leave marks in your Pergo Vinyl floor. The subfloor should be stable and firmly fixed. Furthermore it cannot be soft, damaged or loose laid. The following floor coverings have to be removed: Carpet, needle felt, cushion vinyl, floating laminate and parquet, etc. Does not have to be removed: ceramic tiles, PVC, VCT, glued laminate and parquet, fixed wood boards, etc. Does not have to be removed, but use of PE foil is mandatory to avoid migration: glued PVC, glued linoleum and glued oiled parquet. In case of installation on a wooden subfloor, please remove any existing floor covering first. No signs of mould and/or insect infestations should be present. Make sure the subfloor is level and nail down any loose parts. Apply an appropriate wooden levelling board level floor or levelling compound on top for a perfect subfloor preparation. The levelling boards must be fixed every 30 cm with screws. The crawl space under the plank floor must be sufficiently ventilated. Remove any obstacles and make sure there is sufficient ventilation (minimum 4 cm² total ventilation openings per m² of floor). The moisture content of the wood must not exceed 10%. InstallationInfo_VinylClick_ENG.indd 2 8/08/ :25:40
3 Preparation Make sure the subfloor is completely flat. Cement joints of more than 1 mm in depth and 4 mm in width should be levelled out using an appropriate primer and levelling compound. Any unevenness of more than 1 mm over a length of 20 cm must be levelled out. Bumps should be removed by sanding or scraping. The same applies to unevennesses of more than 2 mm over a length of 1 m. Use an appropriate levelling compound and check if a primer or sealer is needed with the supplier. In some cases, the use of an underlay can avoid extra levelling of the subfloor. >1 mm >1 mm The moisture content of the subfloor must be less than 2,5% CM (cement screed) or less than 0,5% CM (anhydrite subfloor). In the case of floor heating, results must be respectively 1,5% CM and 0,3% CM. Always measure, record and keep your moisture content results. Floor heating systems (water / electricity) which are built-in the screed can be used with Pergo Vinyl if a constant room & floor temperature of 18 (64 F) can be guaranteed during acclimatisation, installation and 48h after installation. For health and safety reasons, a floor surface temperature of maximum 27 (80 F) must be maintained. Seperate rooms with and without floor heating or with different temperature controllers should be installed with a transition profile. For a good preparation, read also the seperate installation instructions for floor heating on Max 27 InstallationInfo_VinylClick_ENG.indd 3 8/08/ :25:43
4 Preparation Make sure that the subfloor is dry, flat, stable, clean and free from grease and chemical substances. If needed, scrape off and clean up old adhesives. Prior to installation, carefully remove all debris (including nails), sweep and vacuum. Repair major surface imperfections and large cracks. It is recommended to remove old skirtings and to install new ones after the installation of the floor. The following standard tools are needed: measurer, safety glasses, thin rope, gloves and a pencil. In addition to the standard tools, we recommend to use the Pergo Vinyl concave cutter knife and installation tool. The latter serves as a 2-in-1 pulling bar and and carpenters square. The use of all accessories other than Pergo Vinyl accessories may cause damage to your Pergo Vinyl. In such case the guarantee provided by Pergo will be void. For this reason we advise to use only Pergo Vinyl accessories, which have been specially designed and tested for use with your Vinyl. Never use a tapping block during the installation of Pergo Vinyl. Check all panels before and during installation in optimal light conditions. Defective panels must never be used. InstallationInfo_VinylClick_ENG.indd 4 8/08/ :25:45
5 Installation During installation, make sure that you mix up the floor panels sufficiently so that there are not too many identical, lighter or darker panels next to each other. To obtain the best visual effect, it is best to fit the panels in the direction of the longest wall and parallel to the incidence of light. Ensure that the end joints of the panels in 2 successive rows are never in line, they should be staggered by at least 30 cm. Measure the room before you start fitting. Make sure that the last row of panels is at least 5 cm wide when finishing the installation. A A>5 cm A >5 cm A Pergo Vinyl has been designed for indoor heated (> 0) (32 F) installations. It cannot be installed in solariums, seasonal porches, camping trailers, boats or unheated applications without being glued. If the temperature of your floor raises above 45, for instance due to direct sunlight, it is recommended to use the Sun/Heat underlay or to install without underlay on a levelled mineral subfloor. If you have any concerns about the temperature of your floor, please contact the Pergo technical department. Recommended PERGO sunsafe underlay > 45 Recommended PERGO basic underlay < 45 First, start in the left corner of the room and fit an underlay if needed. The underlay should be installed progressively together with the floor installation. We strongly recommend to use the special Pergo Vinyl underlays, which have an insulating, sound-reducing and levelling function. An underlay which is too soft or made from the wrong material will damage your floor. A laminate/parquet underlay is not suitable for click LVT. You can find out more information about them and how to use them on the packaging of your underlay or from your dealer. Start the first row with a whole plank. Cut off the long side tongue of the click of first panel. InstallationInfo_VinylClick_ENG.indd 5 8/08/ :25:47
6 Installation Fit the plank with cut off sides against the walls. Make sure that you leave an expansion joint of 2 mm. For installations with floor heating, we recommend to leave an expansion gap of 5 mm. >2 mm Pergo Vinyl can easily be cut using a cutter or utility knife with the decor side face up. When cutting the vinyl plank, mark the line and use the knife to make a firm cut in the surface. Then break off the plank using both hands. Turn the long side of the first panel of the second row into the already fitted panel at an angle of 20 to 30. Move the panel to be fitted slightly up and down and at the same time exert some forward pressure. The panels will click together. Then slide the third plank together horizontally. Slightly lift the plank to be installed by holding your hand underneath. Push the short side joint down gently with your thumb moving from the inner corner towards the outside until you hear a click. Ensure the short side ends are closed by knocking gently on the short side click connection with your wrist. Don t use a hammer or tapping block as it may possible harm your click connection. This is the easiest method for fitting the Uniclic Multifit for Vinyl click panels. InstallationInfo_VinylClick_ENG.indd 6 8/08/ :25:48
7 Installation Now connect the panels of the first two rows on the short sides. Check the expansion gap of and make sure the first rows are on a perfect straight line. You can check this by holding a thin rope along the installed planks and adjust the straightness of your floor when necessary. An expansion gap of 2 mm (0,08 inch) along the perimeter should be maintained. In the width and in the length direction of the planks there is no need for extra expansion gaps. When the remaining piece of underlay is shorter than the width of a panel, install the next underlay. It is recommended to connect the underlays using thin tape. Continue the installation like this row by row towards the end of the room. Always check each joint before continuing. You can press down gently with your thumb on top of every short end joint to ensure good locking. InstallationInfo_VinylClick_ENG.indd 7 8/08/ :25:51
8 Finishing Inspect the final surface of the installed floor. Install Pergo Vinyl skirtings against the wall but never attach the skirting to the floor itself. In places where profiles or skirtings cannot be placed, fill the expansion gaps with an elastic filler like the Pergo Vinyl Kit. For rooms with a high moisture level like bathrooms, Pergo Vinyl Hydrokit can be used. When the new flooring meets a treshold or a doorway, we recommend undercutting the moldings. To secure the right cut, turn a plank upside down and place it on the floor up to the door frame. Then place the Pergo Vinyl hand saw flat against the plank and simply cut through the frame. Remove the cut out and vacuum away debris. You can now simply click the plank in on the long side at the side of the undercutted molding. Use the Pergo Vinyl installation tool as a pull bar to secure absolute tightness in the long and short joint. If it is difficult to tilt the planks (e.g. under radiators), use the Pergo Vinyl installation tool to pull the panels together. In rows where there is a pipe, make sure the pipe falls exactly in line with the short side of two panels. Take a drill bit with the same diameter as the pipe plus 10 mm. Click the panels together on the short side and drill a hole centered on the joint between the two panels. Now you can install the panels. Ø +10mm InstallationInfo_VinylClick_ENG.indd 8 8/08/ :25:53
9 Finishing In case of a double pipe, drill a hole at each of the marked points that is equivalent to the diameter of the pipes plus 10 mm. If located on the long side of the plank, make a 45 degree cut from each hole to the edge of the plank. Ø D Ø D + 10 mm cf. Then, using an appropriate glue along the cut edges of the piece you cut out, glue the piece in place. Be sure no glue comes between the cut out piece and the subfloor InstallationInfo_VinylClick_ENG.indd 9 8/08/ :25:53
10 Maintenance It is allowed to use a vacuum cleaner on your vinyl floor. The use of a steamcleaner is forbidden Your vinyl floor can be cleaned with a damp or wet mop. Pergo Vinyl Clean is a maintenance product specifically developed to keep your new Vinyl floor in top condition. For further information on how to clean and maintain your floor, please visit For specific cleaning instructions in commercial applications or projects, you can contact the Pergo technical department. Always remove spilled liquids immediately from the floor. Protect furniture and chair legs. Use (office) chairs type W and seats with soft wheels that are suitable for a vinyl floor and/or use a suitable desk mat. Never drag heavy items of furniture over the floor but lift them up. Make sure furniture legs have a large surface and are provided with nonstaining floor protectors. The taller and/or wider the furniture feet are, the greater the repartition of weight will be on the floor and the less chance there is to damage the floor. Place non-rubber backed mats at all outside entrances to prevent dirt, grit and soil from being tracked onto your floor. This will reduce damages, the maintenance requirement and extend the life of your floor. Please note that prolonged contact with rubber can cause a permanent stain. Do not allow cigarettes, matches or other very hot items to contact the floor as this may cause permanent damage. Ensure that the indoor climate conditions are always kept > 0 (32 F) and preferably between (64-86 F). If the floor temperature exceeds 45 (113 F), use the Sunsafe underlay. > 0 InstallationInfo_VinylClick_ENG.indd 10 8/08/ :25:54
premium click optimum click
1 In order to obtain a good result, we advise to follow all given instructions carefully. PREPARATION We recommend to order all panels for the same flooring project at the same time. 2 Always store and
More informationUse a special underlay above 45 C. Click-it! Never use a hammer or tapping block. Keep indoor climate conditions above 0 C.
GOLDEN RULES 8-0 C Install your fl oor between 8 and 0 C. Quick-Step Livyn must be acclimatized in the room of installation between 8-0 C (- 8 F) for a period of at least 8 hours before installation. This
More information1. PREPARATION 2. INSTALLATION 3. FINISHING 4. MAINTENANCE
In the following text vinyl floor(s) refers to floors from the Quick-Step Livyn Ambient Glue+ and Balance Glue+ collections. The branded accessories refer to the specific Quick-Step vinyl accessories.
More informationoptimum glue Preparation INSTALLATION INFORMATION We recommend to order all panels for the same commercial flooring project at the same time.
Preparation We recommend to order all panels for the same commercial flooring project at the same time. Always store and transport your vinyl floor carefully to prevent distortions. Store and transport
More informationIN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY.
IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY. 8-0 C < C > C Basic a b SunHeat. PREPARATION Always store and transport Quick-Step Livyn floors carefully to prevent
More informationpremium click optimum click
5 golden rules 48h 18-30 Install your floor with a room- and floor temperature between 18 and 30. Pergo Vinyl must be acclimatized in the room of installation between 18-30 (64-86 F), preferably at normal
More informationMohawk SolidTech. SolidTech Installation Guidelines. Preparation
55 85ºF (13 30ºC) Preparation We recommend placing a single order for all cartons required for a commercial flooring project. 1. Always store and transport SolidTech Luxury Vinyl Flooring on a flat surface
More informationpremium rigid click optimum rigid click
In order to obtain a good result, we advise to follow all given instructions carefully. www.pergo.com Preparation We recommend to order all panels for a commercial flooring project at the same time to
More informationRigid Core Installation & Maintenance Instructions
Rigid Core Installation & Maintenance Instructions Suitability Rigid Core Click Vinyl Flooring is completely waterproof floating floor and has got exceptional acoustic and insulation properties due to
More informationglue E Installation instructions General Acclimatization and storing conditions Subfloor
E Installation instructions General glue 1. We recommend to order all panels for the same flooring project at the same time. Compatibility of panels in repeated orders cannot be guaranteed. 2. Make sure
More informationINSTALLATION INSTRUCTIONS
CLICK BAMBOO FLOORING INSTALLATION INSTRUCTIONS General The locking system is a revolutionary system for installing bamboo floors without using glue. The panels can be clicked together simply. Position
More informationPURE INSTALLATION MANUAL
INSTALLATION MANUAL Pure Click 40 is an LVT floor, designed for use in residential areas. Pure Click 55 is suited for both residential and commercial areas such as shops, hotel rooms, etc. To obtain a
More informationPURE INSTALLATION MANUAL
INSTALLATION MANUAL Pure Click 40 is an LVT floor, designed for use in residential areas. Pure Click 55 is suited for both residential and commercial areas such as shops, hotel rooms, etc. To obtain a
More informationMega Clic Laminate Floor Installation Instructions
Mega Clic Laminate Floor Installation Instructions GENERAL Mega Clic is a revolutionary system for installing laminate floors without using glue. The planks can be clicked together simply, thanks to the
More informationUSA USA USA PURE CLICK
MADE IN BELGIUM MADE IN BELGIUM 0. MADE IN BELGIUM 100 % QUALITY USA USA USA 100 100 % % QUALITY QUALITY PURE CLICK CLICK CLICK DESIGN CLICK DESIGN FLOOR FLOOR INSTALLATION MANUAL 2 Pure Click 40 is a
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS HYDROCORK
INSTALLATION INSTRUCTIONS FOR WICANDERS HYDROCORK GENERAL INFORMATION Hydrocork floors are intended for indoor use only. Please read the following instructions before installation. Hydrocork connection
More informationQuick Step TIMBER Multifit installation instructions
Quick Step TIMBER Multifit installation instructions please read these instructions carefully prior to installation. TIP: Check out our installation videos on www.youtube.com/user/quickstepfloors in GeneRal
More informationQUICK STEP READYFLOR MULTIFIT INSTALLATION INSTRUCTIONS
QUICK STEP READYFLOR MULTIFIT INSTALLATION INSTRUCTIONS Please read these instructions carefully prior to installation. TIP: Check out our installation videos on www.youtube.com/user/quickstepfloors IN
More informationConcrete 1,8 2,0 Anidrite 0,3 0,5
GUIDE FOR FLOATING CORK FLOORS TRANSPORT, STORAGE AND ACCLIMATIZATION Transport and store cartons in a horizontal position. Tiles and adhesive must be acclimated on-site in its original packaging. Store
More informationPURE INSTALLATION MANUAL
PURE INSTALLATION MANUAL 1 Glue down 55 is suited for both residential and commercial areas such as shops, hotelrooms, To obtain a perfect result, we recommend to respect installation instructions carefully.
More informationInstallation Instructions for SuperFast Hurricane
SuperFast Hurricane Installation Instructions for SuperFast Hurricane I. Before You Start / Preparations Please read all the instructions before you begin the installation. Improper installation will void
More informationPARKAY XPR Installation Instructions (Architect Collection)
Parkay Floors 1-855-5-PARKAY www.parkayfloors.com PARKAY XPR Installation Instructions (Architect Collection) BEFORE YOU START PARKAY XPR FLOORING has a patented locking system making it ideal for a floating
More informationINSTALLATION GUIDE. Please read all the instructions before you begin the installation. Improper installation will void warranty.
INSTALLATION GUIDE I. Before You Start / Preparations Please read all the instructions before you begin the installation. Improper installation will void warranty. Important notice All wood based products,
More informationINSTALLATION INSTRUCTIONS - Please read before installation
INSTALLATION INSTRUCTIONS - Please read before installation The floor panels should be transported in a lying down position. Floor panels should be stored in this position in their unopened packages in
More informationIMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING
IMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING ACCLIMATIZATION AND STORAGE Your new flooring has to be acclimatized for 24 hours before installation begins. The flooring must remain
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION For EGGER FLOORING with glueless locking system PRO CLIC! PATENTED www.egger.com INSPECTION RESPONSIBILITY / SUB FLOORS 1. INSPECTION RESPONSIBILITY Laminate flooring from EGGER
More informationSTANDARDS LAMINATE FLOORING (UNILIN A2A) Installation Instructions
STANDARDS LAMINATE FLOORING (UNILIN A2A) Installation Instructions BEFORE YOU START 1. STANDARDS LAMINATE FLOORING has a patented UNILIN A2A locking system. The collections that carry this particular Click
More informationPARKAY LAMINATE FLOORING (UNILIN DROP) Installation Instructions
Parkay Floors 1855-5-PARKAY www.parkayfloors.com PARKAY LAMINATE FLOORING (UNILIN DROP) Installation Instructions BEFORE YOU START PARKAY LAMINATE FLOORING has a patented UNILIN DROP system. The collections
More informationInstallation instruction
TACKY TILE Installation instruction Introduction Tacky Tile has a Tacky technology backing that bonds firmly but not permanently to the subfloor, making installation easy, fast and clean. If at any time
More informationLaminate Flooring Charlestowne Collection
Laminate Flooring Charlestowne Collection Warranty This quality laminate flooring is under warranty for 25 years not to fade, wear through or stain. This warranty applies only to the original purchaser.
More informationGeneral and Installation Instructions Laminate - 2G + 2G
STOP Please inspect product for color, finish, quality and style BEFORE installing any material. SLCC Enterprise, Inc. warranty DOES NOT cover materials with visible defects once they have been installed.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Dear customer, Thank you for buying our veneer Par-ky floor. Please read our installation instructions carefully. If these instructions are not followed, the installer will be
More informationVerify colour and finish before installation. Once the floor is installed, it is deemed to have been inspected, approved and accepted.
CLICK LAMINATE FLOORING INSTALLATION GUIDELINES Before you start read these Installer/Owner Responsibilities: Relative Humidity (RH) requirements: Laminate floors require a Relative Humidity of 35% - 50%
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION EGGER LAMINATE FLOORING with glueless locking system just clic! www.egger.com INSPECTION RESPONSIBILITY / SUB FLOORS 1. INSPECTION RESPONSIBILITY Laminate flooring from EGGER is
More informationSolid Click-Lock Bamboo Product Installation Instructions
Solid Click-Lock Bamboo Product Installation Instructions General The Valinge locking system is a revolutionary system for installing bamboo floors without using glue. However, it can be glued if necessary.
More informationHome Legend Uniclic Cork Product Installation Instructions
Home Legend Uniclic Cork Product Installation Instructions General Uniclic angle is a revolutionary system for installing cork floors without using glue. The panels can be clicked together simply, thanks
More informationInstallation instruction
Installation instruction BJELIN PARQUET PLANK Locking system G/G . Installation preparations 8 h ( h) - C -0% at 0 C - C. Subfloor preparations PE-foil over floor heating mm underlay material: CS > 0 /
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS 5G-C FLOORS
INSTALLATION INSTRUCTIONS FOR WICANDERS 5G-C FLOORS GENERAL INFORMATION Wicanders 5G-C floors are intended for indoor use only. Please read the following instructions before installation. Store planks
More informationHDWPC Flooring Installation Guidelines
HDWPC Flooring Installation Guidelines 02.22.17 The purpose of this manual is to provide general installations recommendations based on certain installation environments. If there are other questions about
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS 2G FLOORS
INSTALLATION INSTRUCTIONS FOR WICANDERS 2G FLOORS GENERAL INFORMATION Wicanders 2G floors are intended for indoor use only. Please read the following instructions before installation. Store planks at room
More informationWPC Vinyl Floor Installation Guide
WPC Vinyl Floor Installation Guide Introduction This guide will take you through the necessary steps to install your Bel-Air WPC Vinyl Flooring. Make sure to carefully read through this guide so that you
More informationRESIDENTIAL 15 YEARS W A RRANTY
R I DE NT I AL ES W A Y 15 YEARS RRANT RESIDENTIAL 15 YEARS W A R R A N T Y KEY FEATURES SUNLITE LOOSELAY LVT TRADITIONAL LAMINATE Sun-proof (withstands direct sunlight) 4 4 7 7 Will not warp or deform
More informationTARKETT EASIUM. Instrucciones de Instalación & Mantenimiento
TARKETT EASIUM Instrucciones de Instalación & Mantenimiento Product usage Recommended tools Easium flooring is not recommended for use in high humidity areas where the floor is usually wet (steam rooms,
More informationUNICLIC INSTALLATION INSTRUCTIONS
UNICLIC INSTALLATION INSTRUCTIONS General Uniclic is a revolutionary system for installing laminate floors without using glue. The panels can be clicked together simply, thanks to the ingenious shape of
More informationLAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING
LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s satisfaction.
More informationLAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING
LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s
More informationHYBRID. Pre-Laying Checks
Warning Veles CK has been developed for exceptional stability in low and high temperatures, however, after installation extreme temperatures (under 5 C or over 50 C) should be avoided by use of interior
More informationDeZignCore Ultra Luxury Vinyl Planks
DeZignCore Ultra Luxury Vinyl Planks v.7-17 Brushed Handscraped Southern Pecan 6 x 48 x 5.5mm DEDCU-162 $4.73/sf Auburn Oak 6 x 48 x 5.5mm DEDCU-921 $4.73/sf Maple 6 x 48 x 5.5mm DEDCU-630 $4.73/sf Hazelnut
More informationLuxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call
Luxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call 702-534-1115 IMPORTANT Save time & avoid frustration! Read these entire instructions before starting your installation! Prior to
More informationInstallation Procedure of Floating floors
SUBFLOOR PREPARATION OF WICANDERS FLOATING FLOORS WITH CORKLOC Wicanders floating floors with Corkloc can be installed in most domestic areas and in almost all commercial areas except in bathrooms, saunas
More informationINSTALLATION INSTRUCTIONS LAMINATE
INSTALLATION INSTRUCTIONS LAMINATE DROP LOCK GENERAL INSTRUCTIONS FOR LAMINATE HARDWOOD FLOORING ACCLIMATION Acclimation is a recommended procedure prior to installation of laminate flooring either on
More informationVESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE
VESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE Vesdura Engineered Vinyl Plank features the patented Unilin interlocking planks for easy installation and is installed as a glueless floating floor. The
More informationMEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL
REVISED 1/24/2017 MEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL PLEASE READ ALL INSTRUCTIONS CAREFULLY, BEFORE YOU BEGIN INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY. Thank you
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
Read all instructions before installing. Incorrect installation will invalidate and void warranty. IMPORTANT Goodfellow Dubaï is guaranteed for use only as a floor covering. Goodfellow Dubaï is intended
More informationLuxury Vinyl Planks with Interlocking Joints (Glueless) Installation Instructions
Luxury Vinyl Planks with Interlocking Joints (Glueless) Installation Instructions Luxury Vinyl Planks are constructed with a joint that locks the planks together to form a tight, durable, water resistant
More informationWellmade En VogueTM Engineered Vinyl Plank Installation Guide
Wellmade En VogueTM Engineered Vinyl Plank Installation Guide Wellmade En VogueTM is a one of a kind engineered vinyl plank flooring that uses no adhesive to bond the vinyl layers together and features
More informationLock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered
Lock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered Please read the following instructions before starting the installation Applications... 1 Pre installation...
More informationINSTALLATION INSTRUCTIONS
About PROTECH Luxury Vinyl Planks 8.7mm WPC Click Lock Contemporary Collection features patented interlocking planks for easy installation and is installed as a glue less floating floor. The interlocking
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
PLEASE READ THE ENTIRE BEFORE PROCEEDING WITH THE INSTALLATION OWNER / INSTALLER RESPONSIBILITY The installer assumes all responsibility for final inspection of product quality. Inspection of the entire
More informationRigid Core (White Label) Planks with Interlocking Joints (Glueless) Installation Instructions
Rigid Core (White Label) Planks with Interlocking Joints (Glueless) Installation Instructions Rigid Core Planks are constructed with a joint that locks the planks together to form a tight, durable, water
More informationSELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD
TOOLS AND MATERIALS SELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD Vapor barrier (minimum 6 mil/0.15 mm) (if needed) Transitional moldings (if needed) Measuring tape Carpenter s square
More informationINSTALLATION INSTRUCTIONS
1 of 6 INSTALLATION INSTRUCTIONS IMPORTANT! Store the floorboards at room temperature for at least 48 hours, still in their packaging, prior to commencing installation. Ideal room temperature is 18-22
More informationVESDURA VINYL PLANKS 7.5MM WPC CLICK LOCK - AMERICANA COLLECTION
VESDURA VINYL PLANKS 7.5MM WPC CLICK LOCK - AMERICANA COLLECTION Before You Start Click lock vinyl plank flooring is normally laid without adhesive. Before installation, planks must be allowed to acclimatize
More informationVESDURA VINYL PLANKS 5.5MM WPC CLICK LOCK - AMERICANA COLLECTION
VESDURA VINYL PLANKS 5.5MM WPC CLICK LOCK - AMERICANA COLLECTION Before You Start Click lock vinyl plank flooring is normally laid without adhesive. Before installation, planks must be allowed to acclimatize
More informationVESDURA VINYL PLANKS 8MM WPC CLICK LOCK - RAINFALL COLLECTION
VESDURA VINYL PLANKS 8MM WPC CLICK LOCK - RAINFALL COLLECTION INSTALLATION Please read all instructions carefully before installation. Improper installation will void warranty. Sunco engineered vinyl plank
More informationINSTRUCTIONS FOR INSTALLATION
INSTRUCTIONS FOR INSTALLATION Dear customer, Thank you for purchasing our Par-ky veneer wood floor. It is essential to read these instructions for installation attentively. If these instructions are not
More informationAttainSilence & Attain
AttainSilence & Attain Attain 4.2mm Click over 1mm ECOsilence, Attain 4.2mm Click AttainSilence Click 4.2.1 & Attain Click 4.2 Technical Manual Installation Maintenance Warranty Manufactured in the U.S.A.
More informationPremium Glueless Luxury Vinyl with Interlocking Joints Installation Instructions
Premium Glueless Luxury Vinyl with Interlocking Joints Installation Instructions Premium Glueless Luxury Vinyl planks are constructed with the patented Uniclic interlocking joint that locks the planks
More informationKronotex Click Installation & Care Guide
Kronotex Click Installation & Care Guide INSPECTION RESPONSIBILITY / SUB FLOORS 1. INSPECTION RESPONSIBILITY Laminate flooring from Kronotex is produced in precise working steps in one of the most modern
More informationINSTALLATION INSTRUCTIONS
VINYL PLANKS 6.5MM HDPC CLICK LOCK REVIVAL COLLECTION General Information 1. Flooring should be transported and stored in a neatly stacked fashion on a smooth flat surface. Be sure to inspect the run numbers/production
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
PLEASE READ THE ENTIRE BEFORE PROCEEDING WITH THE INSTALLATION OWNER / INSTALLER RESPONSIBILITY The installer assumes all responsibility for final inspection of product quality. Inspection of the entire
More informationATTENTION! READ BEFORE INSTALLING!
ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR This flooring replicates the look of a natural product which has natural variations in color and texture. For best visual
More informationPLEASE READ BEFORE INSTALLATION
PLEASE READ BEFORE INSTALLATION Comprehensive Installation and Maintenance Instructions It is important to work out of several cartons to mix the patterns when installing this select flooring product to
More informationGeneral Guidelines Moduleo Click
General Guidelines Moduleo Click The installation of Moduleo Click design floors is straightforward and follows the same guidelines that apply to all quality resilient floors. NATIONAL REGULATIONS Site
More informationWPC VINYL PLANK INSTALLATION GUIDE
WPC VINYL PLANK INSTALLATION GUIDE Please check color selection and style before Installation. NO CLAIMS will be accepted after installation if installation instructions are not followed. NO CLAIMS will
More informationATTENTION! READ BEFORE INSTALLING!
ATTENTION! READ BEFORE INSTALLING! Uniclic Glueless Floating Floor Installation Instructions COLOR VARIATION This flooring is a natural product and color variations are to be expected. For best visual
More informationQuick Step Studio Laminate Flooring Installation Instructions
Quick Step Studio Laminate Flooring Installation Instructions Tools Required for Installation Job Site Site Requirements Laminate is a durable floor covering, not intended as structural material. Laminate
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
PLEASE READ THE ENTIRE BEFORE PROCEEDING WITH THE INSTALLATION OWNER / INSTALLER RESPONSIBILITY The installer assumes all responsibility for final inspection of product quality. Inspection of the entire
More informationFor more information, call PERGO
SYSTEM SYSTEM MADE IN THE USA SPECIALLY DEVELOPED FOR LAMINATE FLOORING FL OZ (33.ml) 0 ON 0 2 0 00 Non Destructive Moisture 3 0 Concrete Encounter Plus 200 20 dlfwej dtra djflsv dlfwe vtra alskdjf vmwjc
More information5G Click Floating Floor Installation Instructions
5G Click Floating Floor Installation Instructions Market Place RPF Can be installed right out of the carton with no acclimation. SUBFLOOR REQUIREMENTS While Market Place RPF is water resistant, it is not
More informationWATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions
WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION Responsibility for the suitability of this flooring
More informationExpanded AmDry Installation Guide
Expanded Tools Required: Tape measure Utility Knife Straight edge Rubber mallet Circular saw with plywood blade Pull or pry bar 1/2 spacers Pencil / marker Tapping block (made from a piece of 2 x 4 ) Getting
More informationVinyl Flooring Installation Guide Go online at bathstore.com for any assistance
Important notice The key to long term performance of any floor is the quality of the sub floor preparations conducted, the installation procedure being correct and the immediate and ongoing care and maintenance
More informationGeneral Commercial Installation Guide LAMINATE
General Commercial Installation Guide LMINTE Laminate & DXP IVC US Commercial Installation Guide - Laminate PressXpress & DropXpress Materials Required for Installation: Small hand saw Jigsaw Pencil ox
More informationINSTALLATION INSTRUCTIONS
VINYL PLANKS 6.5MM HDPC CLICK LOCK PERSPECTIVE COLLECTION General Information 1. Flooring should be transported and stored in a neatly stacked fashion on a smooth flat surface. Be sure to Inspect the run
More informationINSTALLATION INSTRUCTIONS
VINYL PLANKS 4MM HDPC CLICK LOCK FORESIGHT COLLECTION General Information 1. Flooring should be transported and stored in a neatly stacked fashion on a smooth flat surface. Be sure to Inspect the run numbers/production
More informationATTENTION! READ BEFORE INSTALLING!
ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR This flooring replicates the look of a natural product which has natural variations in color and texture. For best visual
More informationInstallation and Maintenance instructions
PVC Floorcovering Resilient Residential Installation and Maintenance instructions February 2014 IMPORTANT! Make sure all specifications and instructions are followed carefully. Floor covering exclusively
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR MIKASA TM REAL WOOD FLOORS These instructions are for all MIKASA TM real wood flooring products made using - - a unique and proven glue - less mechanism
More informationIVC US Residential Installation Guide - Laminate. Leading the Way
IVC US Residential Installation Guide - Laminate Leading the Way IVC US Residential Installation Guide - Laminate PressXpress & DropXpress IVC US Residential Installation Guide Laminate & DXP Materials
More informationCenterStone Collection Installation Guide
CenterStone Collection Installation Guide 2 SPC Installation Instructions Thank you for choosing our product. When properly installed and cared for, your new flooring will be easy to maintain and will
More informationVinyl Flooring Installation Guide Any queries? Visit
Any queries? Visit www.bathstore.com Important notice The key to long term performance of any floor is the quality of the sub floor preparations conducted, the installation procedure being correct and
More informationALL DRAWINGS/ILLUSTRATIONS ARE LOCATED AT THE END OF THE INSTRUCTIONS.
Saxony Installation Instructions Planks are constructed with a joint that locks the planks together to form a tight, durable, water resistant joint. Saxony is installed as a floating floor so it's quick
More informationCOMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION
COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION! IMPROPER INSTALLATION WILL VOID WARRANTY. STOP! WPC Engineered Vinyl Flooring
More informationINSTALLATION INSTRUCTION BJOORN PARQUET PARALLEL ROWS
INSTALLATION INSTRUCTION BJOORN PARQUET PARALLEL ROWS Locking system 5G Index Introduction page 3 Product information If craftsmen/installer is required Important Tools Before installation page 5 Policy
More informationSPECTRA CLICK RESILIENT VINYL PLANK INSTALLATION GUIDELINES
SPECTRA CLICK RESILIENT VINYL PLANK INSTALLATION GUIDELINES About your New Spectra Luxury Vinyl: Spectra features new click/lock technology, resulting in a floating floor system that only requires minimal
More informationLOOSE LAY INSTALLATION GUIDE PAGE 1 of 6
INSTALLATION GUIDE PAGE 1 of 6 MATERIALS REQUIRED FOR INSTALLATION: Tape Measurer Square Ruler Utility Knife 100lb Roller (if using adhesive) ACCEPTABLE SUBFLOORS: Happy Feet International will not warrant
More information