MAJESTIC WETROOMS PRODUCT GUIDE WETROOMS

Transcription

1 MAJESTIC WETROOMS PRODUCT GUIDE WETROOMS

2 CONTENTS 3 INLINE TIMBER 7 FOURWAY TIMBER 11 SOLID FLOOR 20 WATERPROOFING

3 Inline Timber 3 Inline Timber Timber Floors The Inline Timber pre-formed shower base has been developed specifically to allow the installation of a wetroom on a timber floor. Available in a range of sizes, the former has a built-in gradient ensuring that water from the shower is directed towards the integral linear drain, giving a sleek and stylish finish. The key feature of the Inline Timber is its two-way fall which allows the tiling to be laid without diagonal cuts, therefore making it ideal for use with large format tiles. The integrated linear drain can be fitted with one or two traps and a choice of stylish grill finishes. Key Features: Designed for timber floors Two-way fall - suited to large format tiles 9 pre-formed sizes Trimmable by up to 50mm off of all sides Lifetime Guarantee Stylish linear drain available in 3 finishes Variable waste position Flow rate up to 40 L/min by adding a second trap Height adjustable grill

4 Inline Timber 4 Former The Inline Timber floor former is manufactured using a highdensity XPS foam with a mineral coating on both sides, making them both lightweight and easy to handle, whilst maintaining good thermal properties and compressive strength. The former has a pre-formed 12mm fall, providing a consistent two-way gradient every time. The clever design allows for far higher flow rates than a more traditional four-way fall former whilst the linear drain makes it ideal for the installation of large format tiles. Each Inline Timber former is supplied with a stainless steel trim for detailing the difference in tile heights where the former meets the remainder of the bathroom floor - see image for details. Waste The trap has an adjustable ball joint and comes with removable dip-tube. For ease of installation, it can be fitted anywhere within the central section of the trough, making it simple to avoid joists and other such obstructions. Multi-directional outlet Variable position 50mm water seal 50mm outlet, supplied with 50mm-42mm reducer BS1455/1566 Easy to maintain No. of Shower Wastes One Trap Two Traps A single trapped Inline Timber has a flow rate of up to 25 L/min. The trap can be fitted anywhere within the 600mm trough. When a higher flow rate is required simply fit an additional trap, allowing up to 40 L/min. Up to 25 L/min Up to 40 L/min

5 Inline Timber 5 Grill Finish The grill is available in three different finishes. All are manufactured in 316 marine grade stainless steel, ensuring a stunning high quality finish and supplied 600mm long. MG1 Type MG1 Oblong slots: MG1 Rows of oblong slots in a grained stainless steel finish. ST1/ST2 Type ST1 & ST2 - Stone-infill: Allows a section of tile to be inserted to provide a sleek continuous look with a minimal stainless steel frame around the tile. ST1 Suitable for 10-12mm stone / porcelain tiles ST2 Suitable for stone up to 20mm thick Type FL1 - Frameless Infill A similar solution to our ST1 grill but without a visible frame around the tile. Creates the look of a continuous tiled floor. Will take stone / porcelain tiles from 6mm to 20mm thick. FL1 Height Adjustment The grill is height adjustable in 1mm increments to suit tile thicknesses of 6mm to 20mm. Additional spacers are available upon request for tiles thicker than 20mm. How to specify To specify your Inline Timber solution, simply select the former size, the grill finish and any additional traps (depending on the required flow rate). Membrane It is essential that the floor is waterproofed or tanked using one of the Majestic Floor Membranes - See page 20. For timber floors we would recommend the Majestic Floor Membrane is applied to the entire wetroom floor. Floor Build Up

6 Inline Timber 6 900x900 MG1 ITF9X9MG1 590 ST1/ST2 ITF9X9ST1 or FL1 ITF9X9FL x1000 MG1 ITF10X10MG1 695 ST1/ST2 ITF10X10ST1 or FL1 ITF10X10FL x900 (Centre Waste) MG1 ITF12X9CWMG1 695 ST1/ST2 ITF12X9CWST1 or FL1 ITF12X9CWFL x900 MG1 ITF12X9MG1 695 ST1/ST2 ITF12X9ST1 or FL1 ITF12X9FL x1000 MG1 ITF12X10MG1 695 ST1/ST2 ITF12X10ST1 or FL1 ITF12X10FL x900 MG1 ITF15X9MG1 799 ST1/ST2 ITF15X9ST1 or FL1 ITF15X9FL x1000 MG1 ITF15X10MG1 799 ST1/ST2 ITF15X10ST1 or FL1 ITF15X10FL x900 (Centre Waste) MG1 ITF18X9CWMG1 830 ST1/ST2 ITF18X9CWST1 or FL1 ITF18X9CWFL x900 MG1 ITF18X9MG1 830 ST1/ST2 ITF18X9ST1 or FL1 ITF18X9FL1 865 Additional Trap Options Item Additional Trap ITFTRAP 35 s are RRP including VAT.

7 Fourway Timber 7 Fourway Timber Timber Floors The Fourway Timber is a pre-formed shower base developed specifically to allow the installation of a wetroom onto a timber floor. Available in a range of sizes, the Fourway Timber has a built-in gradient ensuring that water from the shower is directed towards the drain outlet. The Fourway Timber has a built-in four-way fall which provides a consistent gradient, making it ideal for use with mosaic tiles. Each Fourway Timber is supplied with our height adjustable shower drain which is available in a choice of stylish finishes. Key Features: Designed for timber floors Four-way fall - suited to mosaic tiles 8 pre-formed sizes Trimmable by up to 50mm off of all sides Lifetime Guarantee Flow rate up to 27 L/min Height adjustable grill Flexible drain outlet 22mm deep tray

8 Fourway Timber 8 Former The Fourway Timber is manufactured using a high-density XPS foam with a mineral coating on both sides, making them both lightweight and easy to handle, whilst maintaining good thermal properties and compressive strength. The four-way fall provides a consistent gradient of approximately 12mm to the drain, making it ideal for the installation of mosaic tiles, but also suited to large format tiles cut and layed in an envelope effect. Waste The trap has an adjustable ball joint for ease of installation and comes with removable dip-tube. The trap is located within the base component which comes un-drilled allowing for extra flexibility. Multi-directional outlet 50mm water seal 50mm outlet, supplied with 50mm-42mm reducer BS1455/1566 Easy to maintain Flow rate up to 27 L/min

9 Fourway Timber 9 Grill Finish The grill is available in two different finishes. MG1 All are manufactured in 316 marine grade stainless steel, ensuring a stunning high quality finish. Type MG1 - Oblong slots: Rows of oblong slots in a grained stainless steel finish. Type ST1 - Stone-infill: Allows a section of tile to be inserted to provide a sleek continuous look with a minimal stainless steel frame around the tile. Suitable for 10-12mm stone/porcelain tiles. Bespoke depths available to order. ST1 Height Adjustment The grill is height adjustable in 1mm increments to suit tile thicknesses of 6mm to 20mm. Additional spacers are available upon request for tiles thicker than 20mm. How to specify To specify your Fourway Timber, first select the required size of shower area, followed by the grill height and finally the grill finish. Membrane It is essential that the floor is waterproofed or tanked using one of the Majestic Floor and Wall Membranes - see page 20. For timber floors we would recommend the Majestic Floor Membrane is applied to the entire wetroom floor. Floor Build Up

10 Fourway Timber x900 MG1 FTF9X9MG1 430 ST1 FTF9X9ST x900 MG1 FTF12X9MG1 469 ST1 FTF12X9ST x1000 MG1 FTF12X10MG1 495 ST1 FTF12X10ST x x x1000 MG1 FTF12X12MG1 580 ST1 FTF12X12ST1 620 MG1 FTF15X9MG1 495 ST1 FTF15X9ST1 528 MG1 FTF15X10MG1 521 ST1 FTF15X10ST x1000 MG1 FTF10X10MG1 440 ST1 FTF10X10ST x900 MG1 FTF18X9MG1 643 ST1 FTF18X9ST1 686 s are RRP including VAT.

11 Solid Floor 11 Solid Floor Drains The Inline Solid Floor Drain has been developed specifically for concrete or screed floors and can be used on concrete slabs, planks and block and beam floors. The key feature of the Solid Floor Drain is its height - the total height from the base to the top of the trough being only 55mm, making it perfect for today s modern construction methods. The drain incorporates a unique waterless trap which has a lifetime guarantee and has been granted BBA approval. It is available with one or two traps and a choice of stylish grill finishes. Key Features: Minimum height 55mm BBA approved Lifetime Guarantee Waterless Trap 360 Rotatable outlet Central trap position as standard Flow rate up to 56 L/min (with 2 traps) Height adjustable Height adjustable grill Grill lengths up to 2000mm (ST1, ST2 and FL1 grills only) Available in 3 grill finishes Available in 2 grill types - Floor grill: for installation off the wall - Wall grill: positioned neatly up against the wall Min 55mm Max 88mm

12 Solid Floor 12 Waterless Trap Trap The waterless trap has been specially designed with a spring loaded mechanism which keeps the trap sealed when not in use. This ensures that even when left unused for prolonged periods the trap cannot dry out, making it ideal for situations where the shower is not in everyday use. The smart design of the linear trough allows the waste position to be rotated through 360 enabling installation in most scenarios with ease. 360 Rotation BBA approved 360 rotatable waste position Easy to clean and replace trap No requirement to top up the trap during long periods of non-use No siphoning of the trap due to other appliances No chance of smells or gases entering the room Lifetime Guarantee No of Traps A single trapped Inline Floor Drain has a flow rate of up to 29 L/min with the support brackets on either side. When a higher flow rate is required a double trap version is available, allowing up to 56 L/min. The traps are positioned near each end of the trough. Single Trap Flow rate up to 29 L/min Centre trap position (shown) Left and right handed options available Outlet position rotates through 360 One Trap Double Trap Flow rate up to 56 L/min For medium-high performance showers Outlet position rotates through 360 Two Traps

13 Solid Floor 13 Grill Length All Inline Floor Drains are supplied with a 660mm drain body/trough. All lengths of grill are then fitted onto this trough. The MG1 grill is available in four standard sizes: 600mm 800mm 1000mm 1200mm The ST1, ST2 and FL1 grills are available in 15 lengths up to 2000mm. The drain body/trough is always installed first prior to the application of the waterproofing membrane, with the grill installed at the point of tiling. Regardless of the length of the grill, the drain body always remains the same at 660mm. Where the grill length exceeds 660mm the ends of the grill overhang the drain body and are supported with tile adhesive. Grill Finish MG1 The grill is available in two different finishes. Both are manufactured in 316 marine grade brushed stainless steel, ensuring a stunning high quality finish. Type MG1 - Oblong slots: MG1 Rows of oblong slots in a grained, brushed stainless steel finish. Type ST1 & ST2 - Stone-infill: Allows a section of tile to be inserted to provide a sleek continuous look with a minimal brushed stainless frame around the tile. ST1 suitable for 10-12mm stone/porcelain tiles. To allow for stone/ porcelain tiles up to 20mm order ST2. ST1 & ST2 Type FL1 - Frameless Infill A similar solution to our ST1 grill but without a visible frame around the tile. Creates the look of a continuous tiled floor and offers the perfect solution to match all brassware finishes. Will take stone/ porcelain tiles from 6mm to 20mm thick. FL1 Ultimately the grill finish is the only visible element of our wetroom system and as such, is often the defining factor of the overall design. From the contemporary Stone-Infill or ultra stylish Frameless to the simplicity of the Brushed stainless steel, we have a grill finish to complement any design. We manufacture all of our grills using only 316 marine grade stainless steel, ensuring a stunning high quality durable finish, complete with our Lifetime Guarantee. The grill insert is easily removed for cleaning and maintenance using the key provided with the grill.

14 Solid Floor 14 Grill Type - Wall or Floor There are two types of grill available with the solid floor drain, both fit onto the drain body using 8 pre-set fixing points. Both of the Floor Grill and Wall Grill are independently height adjustable, enabling the grill to be positioned precisely to suit the tile thickness being used. The final position of the Wall Grill is also independently width adjustable by up to 38mm, allowing the grill to be neatly positioned up against the wall tile, after the drain body has been installed, for a perfect finish every time. Floor Grill Wall Grill The centre point of the Floor Grill is typically positioned 150mm from the wall, to create a two-way fall within the shower. Grill width 58mm. The Wall Grill is positioned neatly up against the wall, to create a one-way fall within the shower. Grill width 86mm.

15 Solid Floor 15 Typical detail with Wall Grill Wall Grill with Standard Bracket INSULATION MAJESTIC FLOOR MEMBRANE MAJESTIC WALL MEMBRANE STONE / TILE TILE ADHESIVE SCREED SCREED LAID TO FALLS ST1 WALL GRILL A SLAB LINEAR SCREED DRAIN STANDARD BRACKETS Key Features: Use to create a one-way fall DIMENSION A: MIN. - 55mm Minimum height 55mm MAX. - 88mm (Extension brackets available) DRAWN Waterless AS - 78mm trap 360 Rotatable waste outlet Left or Right handed options available as a special order Flow rate up to 56 L/min Height adjustable brackets THIRD ANGLE PROJECTION Grill lengths up to 2000mm (ST1, ST2 & FL1 only) ORDER REF CD ISS DATE DRN CHKD APRD MATERIAL FINISH Single Trap TOLERANCE - UNLESS STATED ± 0.2 ORIGINAL SCALE Double Trap CLEAN 1:3 DIMENSIONS IN MILLIMETRES UNLESS STATED TITLE DRG. No. MAJESTIC SHOWER COMPANY LTD 2 NORTH PLACE EDINBURGH WAY HARLOW ESSEX, CM20 2SL TEL : INLINE WALL DRAIN WITH SCREED LAID TO FALLS MJS-TD-LSD601 CURRENT ISSUE Standard Height Bracket GRILL - HEIGHT & WIDTH ADJUSTABLE 40mm ABS PIPE CONNECTION BRACKETS HEIGHT ADJUSTABLE THIRD ANGLE PROJECTION ORDER REF MATERIAL FINISH CLEAN TOLERANCE - UNLESS STATED ± 0.2 ORIGINAL SCALE CD 1:1 DIMENSIONS IN MILLIMETRES ISS DATE DRN CHKD APRD UNLESS STATED TITLE DRG. No. TD-LSD901 CCL WETROOMS LTD LODGE FARM HOOK ROAD NORTH WARNBOROUGH HOOK ROAD, RG29 1HA TEL : LSD WALL ON STANDARD BRACKETS CURRENT ISSUE

16 Solid Floor 16 Typical detail with Floor Grill Floor Grill with Standard Bracket MAJESTIC WALL MEMBRANE MAJESTIC FLOOR MEMBRANE INSULATION SCREED LAID TO FALLS STONE / TILE ST1 FLOOR GRILL TILE ADHESIVE SCREED LINEAR SCREED DRAIN STANDARD BRACKETS Key Features: Use to create a two-way fall Minimum height 55mm Waterless trap 360 Rotatable waste outlet Centre, left and right handed waste position Flow rate up to 56 L/min Height adjustable brackets Grill lengths up to 2000mm (ST1 & FL1 only) Standard Height Bracket GRILL - HEIGHT ADJUSTABLE 40mm ABS PIPE CONNECTION A 5 12 SLAB Single Trap Double Trap BRACKET HEIGHT ADJUSTABLE 240

17 Solid Floor 17 How to build your Drain There are two components required to specify an Inline Solid Floor Drain - the drain body and the grill. To specify the drain body, select the required number of traps along with the bracket type. Then simply choose the grill, selecting the desired type, length and finish. Step 1 Drain Body Number of traps Single Trap - flow rate up to 29 L/min Double Trap - flow rate up to 56 L/min Bracket type Standard Height - adjustment 55mm-88mm* * Extension brackets are available for floor depths above 88mm. Step 2 MG1 Grill Grill type - Wall or Floor Floor Grill - for installation off the wall Wall Grill - positioned neatly up against the wall ST1 & ST2 Grill length 15 Standard lengths Bespoke lengths from 600mm mm Grill finish 3 stylish grill finishes FL1 Membrane It is essential that the floor is waterproofed or tanked using one of the Majestic Floor Membranes - See page 20. For solid floors we would recommend that the Majestic Floor Membrane is applied to the entire wetroom floor.

18 Solid Floor 18 Product s Drain Body Type Drain & Flow rate Traps 29 L/min 1 : Centre IFD1C 285 Min 55mm Max 88mm 56 L/min 2 IFD2D 350 Height Extension Brackets Type Bracket Type Suitable For Single Trap IFDHEBC 38 Centre Double Trap IFDHEBD 50 Use extension brackets where the required height of the drain body exceeds 88mm. Each bracket will increase the height by 30mm. Multiple brackets can be used if necessary. s are RRP including VAT.

19 Solid Floor 19 Product s Wall Grill MG1 ST1, ST2, FL1 Type Length 600mm IWG mm* IWG mm IWG mm* IWG mm IWG mm* IWG mm IWG mm* IWG Grill Finish Add code for Grill Finish: EXAMPLE: IWG600MG1 MG1 = Stainless ST1 = Suits 10-12mm tile thickness ST2 = Suits 18-20mm tile thickness FL1 = Suits any tile thickness up to 20mm 1400mm* IWG mm* IWG mm* IWG mm* IWG mm* IWG mm* IWG mm* IWG * ST1, ST2 and FL1 only Floor Grill MG1 ST1, ST2, FL1 Type Length 600mm IFG mm* IFG mm IFG mm* IFG mm IFG mm* IFG mm IFG mm* IFG Grill Finish Add code for Grill Finish: EXAMPLE: IFG600MG1 MG1 = Stainless ST1 = Suits 10-12mm tile thickness ST2 = Suits 18-20mm tile thickness FL1 = Suits any tile thickness up to 20mm 1400mm* IFG mm* IFG mm* IFG mm* IFG mm* IFG mm* IFG mm* IFG * ST1, ST2 and FL1 only Tile Trim Type Length 300/600 ITT /700 ITT /900 ITT /1200 ITT /1500 ITT s are RRP including VAT.

20 Solid Floor 20 Waterproofing Our Floor Membrane is a self-adhesive waterproof membrane designed for use prior to the application of ceramic tiles or natural stone onto both Timber Floors and Solid Floors in wetrooms and other critical areas. Key Features: Lifetime Guarantee Suitable for timber and solid floors Self-Adhesive - Quick and easy to apply Ready to tile immediately Ideal for fast track construction Supplied as a kit Factory controlled thickness Membrane Thickness Joint Tape thickness Tensile Strength (ASTM D3759) Elongation at break (ASTM D3759) Peel Adhesion at 180 angle (ASTM 3330) 1mm 1mm 140N /5cm - (Cross Direction) 120% - (Cross Direction) >11N/mm Majestic Butyl Floor Membrane Type Suitable For Floor Membrane 5m2 Kit WMFK5 345 Floor Membrane 10m2 Kit WMFK Majestic Wall Membrane Type Suitable For Wall Membrane 8kg WMW8 115 Wall Membrane Reinforcing Tape 5m WMRT5 45 Wall Membrane Primer 1Ltr WMP1 30 s are RRP including VAT.