Donn Brand Suspension Systems. Accessory. Product Guide

Transcription

1 Donn Brand Suspension Systems Accessory Product Guide

2 Since 1957, DONN brand suspension systems have set the standard worldwide for the ceiling suspension industry. Donn suspension systems are readily available in all markets, install faster than any other suspension system, and maintain modularity (squareness) better than any other system. The following pages represent USG s most popular suspension system accessory items, which are designed to assist you in installing perfect ceilings with minimum effort. If you are in doubt about the application of any of our accessory items or any of our other products, please call our Technical Service Department, USG.4YOU, or your local USG Sales Representative. Installing Perfect Ceilings

3 User s Guide Use this brochure to design, specify, bid and install USG Donn suspension systems. Pages Moldings 4 Angle Molding Shadow Molding US Channel Wall Molding "F" Molding Molding Accessories 6 Outside Corners Inside Corners Grid Installation Accessories 7 Galvanized Hanger Wire Stabilizer Bars Partition Attachment Grid to Primary Support Seismic Compression Posts Hold-Down Clips Grid to Molding Tee Accessories FINELINE Accessories Tee to Tee Light Fixture Accessories 12 Light Fixture Clip Miscellaneous Accessories 13 Cross Tee Hole Punches Touch-Up Paint Air Diffusers Separation Joints 14 Tee-Face Sleeves Expansion Joint Moldings 3 Accessory Product Guide

4 Donn Suspension Systems Moldings Angle Molding Angle Molding w/gasket Shadow Molding M12CE Use for standard ceiling perimeters. Use in cleanroom applications with Donn For creating reveals at ceiling perimeters. CE suspension system. Also helps to hide imperfections in drywall partitions and bulkheads. A B C D Length x A x B x C x D Packaging/Ctn. Number LF Pcs. Wt. (lbs.) Angle Molding M71 12 x 7/8 x 7/8 Wall Molding M7OL 12 x 7/8 x 7/8 Overlapping Wall Molding M7A 12 x 7/8 x 7/8 Aluminum Wall Molding M x 7/8 x 7/8 Wall Molding M7SS 12 x 7/8 x 7/8 Stainless Steel Wall Molding M7Z 12 x 7/8 x 7/8 Hot-Dipped Galvanized Steel Wall Molding M x 9/16 x 15/16 Wall Molding M x 9/16 x 15/16 Wall Molding M12 10 x 1 x 1 1/2 Wall Molding MC11A25 10 x 1 x 1 Aluminum Cap Wall Molding M12CE 10 x 1 x 1 1/2 Wall Molding w/ gaskets M20SM 10 x 1 x 2 Wall Molding M20SM-2 10 x 2 x 2 Wall Molding M x 1 x 2 Wall Molding Shadow Molding MS x 15/16 x 1/4 x 5/16 x 15/16 Shadow Molding (Option 1) Length x A x B x C x D 12 x 15/16 x 5/16 x 1/4 x 15/16 Shadow Molding (Option 2) (See illustration above) MS x 9/16 x 1/4 x 5/16 x 3/4 Shadow Molding (Option 1) x 3/4" x 5/16 x 1/4 x 9/16 Shadow Molding (Option 2) MS x 3/4 x 3/8 x 1/2 x 3/4 Shadow Molding (Option 1) x 3/4 x 1/2 x 3/8 x 3/4 Shadow Molding (Option 2) MS x 7/8 x 3/4 x 3/4 x 7/8 Shadow Molding MS x 3/4 x 3/4 x 3/4 x 3/4 Shadow Molding MS x 7/8 x 3/8 x 3/8 x 9/16 Shadow Molding (Option 1) x 9/16 x 3/8 x 3/8 x 7/8 Shadow Molding (Option 2) MS x 7/8 x 3/4 x 9/32 x 1-1/4 Shadow Molding Notes (1) M7 and M9 available in color. For colors other than Flat White and Flat Black, packaging is 240 LF per carton. (2) Not all M20 modlings are available in all areas. Please contact your USG Sales Representative. (3) MS154 and MS174 available with exposed horizontal leg painted a color. 4 Accessory Product Guide

5 Moldings US Channel Wall Molding US Channel Wall Molding w/gasket F-Molding US28CE Use with C-8 clip to hold down perimeter Use with C-8 clip in cleanroom application Use to create ceiling breaks, soffits and ceiling panels. with DONN CE suspension system. changes in elevation. B A C Length x A x B x C US Channel Wall Molding F-Molding Packaging/Ctn. Number LF Pcs. Wt. (lbs.) US12 10 x 3/4 x 1/2 x 1 U-Molding US20 10 x 1-1/4 x 1/2 x 1 U-Molding US28 10 x 1-11/16 x 1/2 x 1 U-Molding US /16 x 1/2 x 1 U-Molding UA25 10 x 1-9/16 x 1/2 x 1 Aluminum U-Molding U-2-3/32 12 x 2-3/32 x 7/8 x 1-1/8 Aluminum U-Molding, Flat White US28CE 10 x 1-11/16 x 1/2 x 1 U-Molding w/ gaskets, Flat White MF8 10 x 1/2 F-Molding (for 1/2 panels) MF10 10 x 5/8 F-Molding (for 5/8 panels) Accessory Product Guide

6 Donn Suspension Systems Molding Accessories Square Molding Corner Clip Outside Corner Radius Molding Corner Clip JS JS174 JH, JB Use with angle molding. Use with MS174 shadow molding. For radius or bullnose corners. Field-Modified Corner Inside Corner Angle Mold Prefabricated Inside Corner JM16 A2 A174 Cut out clip to fit field condition. Use with angle molding. Use with MS174 shadow molding. Outside Corners Inside Corners Packaging/Ctn. Number Pcs. Wt. (lbs.) JS9 Square 90 Outside Corner Cap for 9/16 molding JS14 Square 90 Outside Corner Cap for 7/8 molding JS16 Square 90 Outside Corner Cap for 1 molding JS174 Square 90 Outside Corner Cap for MS174 Shadow Molding JS274 Square 90 Outside Corner Cap for MS274 Shadow Molding JH9 1 Radius 90 Outside Corner Cap for 9/16 molding JH12 1 Radius 90 Outside Corner Cap for 3/4 molding JH14 1 Radius 90 Outside Corner Cap for 7/8 molding JH15 1 Radius 90 Outside Corner Cap for 15/16 molding JH16 1 Radius 90 Outside Corner Cap for 1 molding JB14 3/4 Radius 90 Outside Corner Cap for 7/8 molding JB16 3/4 Radius 90 Outside Corner Cap for 1 molding JM16 Field-Modified Corner for 1 molding A2 Inside Corner Cap for 7/8 molding A174 Inside Corner Cap for MS174 Shadow Molding A274 Inside Corner Cap for MS274 Shadow Molding Accessory Product Guide

7 Grid Installation Accessories Galvanized Hanger Wire Drywall Grid Hanger Clip Grid Load Transfer Bracket A B C To suspend acoustical ceilings. Also use for To suspend secondary ceiling. To suspend secondary ceiling. flat and curved USG Drywall Suspension System. Furring Clip for Grid to Channel Seismic Attachment Clip for Perimeter Molding Attachment Clip D Conditions F E Connect grid to 1-1/2 channel. Attach tee ends at the perimeter in seismic Attach tees to angle molding and shadow design categories C, D, E and F. molding. Packaging/Ctn. Detail Number Pcs. Wt. (lbs.) Key Galvanized Gauge Wrapped 12 ft.; 50 lb. bundle A Hanger Wire Gauge Wrapped 12 ft.; 36 lb. bundle A Consult Customer Service for Gauge Wrapped 16 ft A available lengths in your area. Grid to Primary Support DGHC Drywall Grid Hanger Clip B Grid Load Transfer Bracket, 15/16 grid C Grid Load Transfer Bracket, 9/16 grid C Grid Load Transfer Bracket, 1-1/2 grid C V-14 Furring Clip for Grid to Channel D Grid to Molding2 ACM7 Seismic Perimeter Attachment Clip E MAC2 Molding Attachment Clip F Note (1) For special lengths, contact your USG Sales Representative. Hanger wire complies with Federal Specification QA-W-461H. (2) Please refer to for more information about seismic applications with the ACM7 seismic clip. 7 Accessory Product Guide

8 Donn Suspension Systems Grid Installation Accessories MT/CT Converter 2-Way Seismic Separation Joint Clip 3-Way Off-Module Connector G H1 H2 Changes main-tee direction 90 from adjacent For seismic separation joints in IBC Seismic Use with cross tees and main tees that are he main tee. Design Categories D,E, and F. same height. 4-Way Seismic Separation Joint Clip Paired Main Tee Clip Light-Fixture Clip I J K For seismic separation joints in IBC Seismic Use for linear air diffusers; use only with For CENTRICITEE suspension system; use black Design Categories D,E, and F. DX /DXL, DXLA, ZXLA, FINELINE (DXF) clips with parabolic fixtures. Cross tee must be and FINELINE 1/8 (DXFF) connected to main tee. Tee to Tee Light Fixture Clip Packaging/Ctn. Detail Number LF Pcs. Wt. (lbs.) Key DXMT/CT 9 x 1-1/2 MT/CT Converter, changes MT direction G DH2 2-Way Seismic Separation Joint Clip H1 DH3 3-Way Off Module Connector H2 DH4 4-Way Seismic Separation Joint Clip I V-32 Paired Main Tee Clip (2 separation center to center) J LFC Light-fixture hold-down clip for 9/16 grid K Notes (1) Please refer to Submittal Sheet AC3301 for more information about the DH2 2-way seismic separation joint clip. (2) Please refer to Submittal Sheet AC3271 for more information about the DH4 4-way seismic separation joint clip. 8 Accessory Product Guide

9 Grid Installation Accessories Seismic Compression Post 1 Tee Face Sleeve Tee Face Sleeve 2 L M1 M2 For lateral bracing in IBC Seismic Design To cut in tees to existing system and for To cut in tees to existing system and for Categories D, E, F and exterior ceiling separation joints. separation joints. applications for wind uplift. DX Accessory Hanger Hook 3 Partition Attachment Clip 4 O P1 and P2 Remove top clip for use with standard 1/4 FINELINE suspension system. DXT DX DXF Reveal edge Squarel edge Seismic Compression Posts Tee Accessories Partition Attachment Packaging/Ctn. Detail Number Pcs. Wt. (lbs.) Key VSA18/30 Adjustable 18 to L VSA30/48 Adjustable 30 to L VSA48/84 Adjustable 48 to L VSA84/102 Adjustable 84 to L VSA102/120 Adjustable 102 to L VSA120/144 Adjustable 120 to L TFS-1 Tee Face Sleeve (3 long) for 15/16 DX/DXL Systems M TFS-2 Tee Face Sleeve (3 long) for 9/16 DXT Systems M TFS-3 Tee Face Sleeve (3 long) for DXF Systems with 1/4 Reveal M TFS-4 Tee Face Sleeve (3 long) for DXFF Systems with 1/8 Reveal M TFS-5 Tee Face Sleeve (3 long) for DXI Systems with 1/8 Reveal M2 TFS-5 DXI FC Tee Face Intersection sleeve (3 long) for DXI Systems with 1/8 Reveal M2 AH1 Accessory Hanger Hook (white, injection molded) 50 1 O PAC15-SQ Partition Clip for 15/16 or 9/16 SQ panels (245339) P1 PAC15-SL Partition Clip for 15/16 SL panels (254340) P2 PAC 9-FL Partition Clip for 9/16 FL panels (254341) P2 Notes (1) Please refer to Compression Posts (SC2497) for more information about USG compression posts. (2) The DXI Tee-Face Intersection Sleeve (TFS-5 DXI FC) is used for off-module intersections to maintain the clean, uninterrupted aesthetic of the grid profile. (3) Whenever possible the accessory hanger hook should be installed on a main tee. If an accessory hanger hook is installed on a main tee the load should not exceed 10 lbs. without installing a supplementary hanger wire support to the structure at the location of the hanger hook. If an accessory hanger hook is installed on a cross tee the load should not exceed 4 lbs. without installing a supplementary hanger wire support to the structure at the location of the hanger hook. The accessory hanger hook is not designed to support loads exceeding 30 lbs. (4) The partition attachment clip shown above is manufactured by Revoe Manufacturing of Canada ( and can be purchased through USG. 9 Accessory Product Guide

10 Donn Suspension Systems Grid Installation Accessories Panel Retention Clip Hold-Down Clip Fire-Rated Grid Hold-Down Clip P3 Q1 Q2 Attaches to 1-1/2 main tees and cross tees Used when required in some fire-rated To maintain a cleanroom seal. behind lay-in ceilings. The retention clips help assemblies. prevent panel displacement from incidental contact. Recommended with ROCK FACE ceiling panels for impaction resistant systems. Variable Locking Hold-Down Clip Accessible Hold-Down Clip Variable Hold-Down Clip Q3 R S Use as a locking hold-down clip for various Use as a hold-down clip for 5/8 panels. For 5/8 to 3/4 panels. acoustical and metal panels. Provides ready accessibility. Packaging/Ctn. Detail Number Pcs. Wt. (lbs.) Key Panel Retention Clip¹ Attaches to 1-1/2 main tees and cross tees behind lay-in ceilings. The retention P3 clips help prevent panel displacement from incidental contact. Recommended with ROCK FACE ceiling panels for impaction resistant systems. Hold-Down Clips L15 Hold-Down Clip for 5/8 fire-rated panels Q1 L15CE Hold-Down Clip for panels in CLEAN ROOM applications Q2 (same clip as L15; smaller quantity) PZ Variable Locking Hold-Down Clip Q3 L45 Accessible Hold-Down Clip for 5/8 panels R V15 Variable Hold-Down Clip S Note (1) For more information about the Keep Clip from American Retention Components, Inc., please visit 10 Accessory Product Guide

11 Grid Installation Accessories Wall Spring Clip Miter Closure Clip for FINELINE system CELEBRATION Hold-Down Channel Clip T U V To hold down perimeter ceiling panels. Useful for maintaining cleanroom seal with US28CE molding. For closing off unused miters. Partition Attachment Clip T-Bolt FINELINE Cut-Off Die W X Y To screw-attach ceiling-height partitions. To bolt-attach partitions, signage or pendant- Use to field-cut FINELINE tees. mounted indirect lighting. Packaging/Ctn. Detail Number Pcs. Wt. (lbs.) Key Hold-Down Clips C-8 Wall Spring Clip T continued C-8CE Wall Spring Clip (same clip as C-8; smaller quantity) T MCC3 2 Miter Closure Clip for 1/8 FINELINE suspension system 50 1 U MCC2 2 Miter Closure Clip for standard FINELINE suspension system 50 1 U T15 10 x 11/32 x 1-9/16 x 3/4 Panel Hold-Down Clip V U-2-3/32 10 x 11/32 x 2-3/32 x 3/4 Panel Hold-Down Clip V FINELINE PAC1 3 Partition Attachment Clip 50 1 W Accessories TB1 1 x 1/4 20 T-Bolt X FC1 FINELINE Suspension System Cut-Off Die (scaffold mount) 1 10 Y Note (1) Please refer to USG Exterior Ceiling Applications (SC2561) for more information about exterior ceiling applications with the U-2-3/32 hold-down clip. Use T-15 hold-down clip with UA25 molding and use U-2-3/32 hold-down clip with U-2-3/32 molding. 11 Accessory Product Guide

12 Donn Suspension Systems Stabilizer Bars Standard Stabilizer Bar Locking Stabilizer Bar Accessible Stabilizer Bar A B C Stabilizer Bars Catalog Number Description Packaging/Ctn. Detail Key LF Pcs. Wt. (lbs.) Standard Stabilizer Bars CC15-20 Standard 20 Stabilizer Bar A CC15-30 Standard 30 Stabilizer Bar A CC Standard 4' Stabilizer Bar notched 2' on center A Locking Stabilizer Bars SB12 Locking 12 Stabilizer Bar B SB24 Locking 24 Stabilizer Bar B SB24-A Locking 24 Stabilizer Bar Elongated for Ashlar Connection B SB36 Locking 36 Stabilizer Bar B SB48 Locking 48 Stabilizer Bar B SB48-24 Locking 24 Stabilizer Bar 24" Center to Center Notch B SB60 Locking 60 Stabilizer Bar B Accessible Stabilizer Bars ASB24 Accessible 24 Stabilizer C ASB30 Accessible 30 Stabilizer Bar C ASB48 Accessible 48 Stabilizer C ASB600MM Accessible 600mm Stabilizer Bar 15(m) C ASB900MM Accessible 900mm 22.5(m) C ASB1200MM Accessible 1200mm 30(m) C Notes (1) Please refer to Perimeter Treatment (SC2540) for more information about USG stabilizer bars in a seismic application. (2) Please refer to Ashlar Condition (SC2550) for more information about the SB24-A stabilizer bar elongated for ashlar modules. (3) Please refer to Application Guide (IC592) for more information about USG stabilizer bars in plank and large panel applications. 12 Accessory Product Guide

13 Miscellaneous Accessories Universal Field Cross Tee Hole Tool Hand-Held Field Cross Tee Hold Tool Air Diffuser For all DONN suspension systems. For all DONN suspension systems. Field-cut foil-backed ceiling panel to fit diffuser face. Use with FINELINE and CENTRICITEE suspension systems. SB2 Sloped Ceiling Bracket Packaging/Ctn. Number Pcs. Wt. (lbs.) Cross Tee Universal Field Cross Tee Hole Tool 1 30 Hole Punches Hand-Held Cross Tee Hole Tool Replacement Die Block for Universal Cross Tee Tool Replacement Die Block for Hand-Held Cross Tee Tool Replacement Punch for Universal Cross Tee Tool Replacement Punch for Hand-Held Cross Tee Tool 1 1 Touch-Up Paint B14 Flat Black Spray Paint (205)1 6 7 B13 Flat White Spray Paint (050) PC15 GAL Standard Gallon PC16 QT Standard Quart PC19 GAL Custom Gallon 1 12 Air Diffusers Recommended for use with 9/16 systems PC20 QT Custom Quart 1 3 AD16 2 x 2 1 Slot with 6 Collar 1 7 AD18 2 x 2 1 Slot with 8 Collar 1 7 AD26 2 x 2 2 Slot with 6 Collar 1 8 AD28 2 x 2 2 Slot with 8 Collar 1 8 AD38 2 x 2 3 Slot with 8 Collar 1 8 AD310 2 x 2 3 Slot with 10 Collar 1 9 AD410 2 x 2 4 Slot with 10 Collar 1 10 AD412 2 x 2 4 Slot with 12 Collar 1 10 Adjustable Wall Molding SB2 SB2 adjustable wall molding bracket used to secure standard wall Bracket molding at an angle to accommodate a sloped acoustical ceiling Notes (1) One carton contains six 12 oz. cans. Paints cannot be shipped air freight. (2) Specify color number from price list. (3) Punch tools are not covered under the USG Standard Product Warranty. There is a basic and limited warranty for 3 months of normal use. Any damage beyond 3 months must be evaluated and a repair fee may be assessed. Please refer to AC3264 for more information. 13 Accessory Product Guide

14 Donn Suspension Systems Separation Joints When a separation joint is required, USG offers several options that are practical, easy to install, and designed for minimal visibility. DONN separation joints represent the greatest range of options to satisfy the stringent requirements for separation joints. For more information on seismic separation joints, please refer to Seismic Technical Guide SC2496. Tee Faced (Main Tee or Cross Tee) Sleeve Tee Face (Cross Tee) Sleeve Expansion Joint M12 Molding Available for DX/DXL, DXI, DXT and DXF/DXFF. hanger wire 12-ga. hanger wire cross tee field cut 1" cross tee 12-ga. hanger wire (existing) at 4'-0" o.c. existing main tee cross tee hanger wire near tee end (3) M12 wall moldings main tee or cross tee tee-face sleeve one side of splice cap crimped to allow movement only on opposite end tee-face sleeve 1" min. typ. one side of splice cap crimped to allow movement only on opposite end lay-in ceiling panel 1" typ. pop rivet (typical) Expansion Joint M20 Molding Expansion Joint US28 Molding Expansion Joint Accordion Style 12-ga. hanger wire min. within 8" of tee end 12-ga. hanger wire at 4'-0" o.c. stabilizer bar along tee ends to prevent spreading main tee field-fasten molding to main tee and through ct clips hanger wire tee cross tee field-fasten channels securely back to back and field-punch hanger wire holes hanger wire main tee cross tee main tee or cross tee M20 1" x 2" wall molding 1" min. typ. flatten CT clip cross tee US28 channel molding lay-in ceiling panel expansion joint by others Expansion Joint M7 Molding Expansion Joint DH2 Slip Joint hanger wire main tee or cross tee punch and hang M7 or M12 wall moldings in field lay-in ceiling panel 4-way seismic separation joint clip fasteners fasten near horizontal face to assure tight joint 1/2" typ. back to back M7 or M12 wall moldings DXW main tee 14 Accessory Product Guide

15

16 Technical Service 800 USG.4YOU Web Site Samples/Literature Samples/Literature Samples/Literature/Fax Customer Service Note All products described here may not be available in all geographic markets. Consult your local sales office or representative for information. Trademarks The following are trademarks of USG Interiors LLC: CELEBRATION, CENTRICITEE, CLEANROOM, DONN, DX, DXL, DXLA, FINELINE. USG in stylized letters. USG is a trademark of USG Corp. Notice We shall not be liable for incidental and consequential damages, directly or indirectly sustained, nor for any loss caused by application of these goods not in accordance with current printed instructions or for other than the intended use. Our liability is expressly limited to replacement of defective goods. Any claim shall be deemed waived unless made in writing to us within thirty (30) days from date it was or reasonably should have been discovered. Safety First! Follow good safety and industrial hygiene practices during handling and installation of all products and systems. Take necessary precautions and wear the appropriate personal protective equipment as needed. Read material safety data sheets and related literature on products before specification and/or installation. Manufactured by USG Interiors, LLC. 550 West Adams Chicago, IL AC2396/rev , USG Interiors, LLC Printed in U.S.A.