NAVSEA STANDARD ITEM. 1.1 Title: Piping System Cleanliness (Non-Nuclear); accomplish
|
|
|
- Leonard Dylan Holt
- 5 years ago
- Views:
Transcription
1 NAVSEA STANDARD ITEM ITEM NO: DATE: 18 JUL 2014 CATEGORY: II 1. SCOPE: 1.1 Title: Piping System Cleanliness (Non-Nuclear); accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9AAO-AB-GOS-010, General Specifications for Overhaul of Surface Ships (GSO) , General Specifications for Deep Diving SSBN/SSN Submarines 2.4 S9086-RK-STM-010/CH-505, Piping Systems 2.5 MIL-STD-1330, Precision Cleaning and Testing of Shipboard Oxygen, Helium, Helium-Oxygen, and Nitrogen Systems 2.6 MIL-STD-419, Cleaning, Protecting, and Testing Piping, Tubing, and Fittings for Hydraulic Power Transmission Equipment 2.7 MIL-STD-1622, Cleaning of Shipboard Compressed Air Systems 2.8 S9086-RW-STM-010/CH-516, Refrigeration Systems 3. REQUIREMENTS: 3.1 Accomplish the general cleaning requirements of 2.2 through 2.4 for new, modified, or repaired non-nuclear piping systems and components of nuclear and non-nuclear powered naval vessels. Accomplish the system cleaning requirements of 2.5 through Clean to the following acceptance standard: Cleanliness Level II: Surface shall be visually free of grease, oil, flux, scale, dirt, loose particles and any other contamination foreign to the base metal. Tap water residues on all metals and light superficial rust on carbon steel surfaces, caused by short time exposure to the atmosphere, are permitted. Light dust on cleaned surfaces is not objectionable, provided that the quantity and size of the particle does not adversely affect system operations. 1 of 5 ITEM NO:
2 Cleanliness Level III: Surface shall be reasonably free of contamination and any remaining residue on the surface does not interfere with system operations or damage system components. 3.2 Accomplish local cleaning to areas where existing system cleanliness has been lost in a localized area (such as metal shavings deposited in a pipeline while removing a section for replacement). Restore cleanliness by locally swabbing, wiping, vacuuming, etc., the area to meet existing system cleanliness. (V) VERIFY CLEANLINESS Verify that existing system cleanliness was maintained. 3.3 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of compressed air systems in accordance with Section 551 of 2.2 and Verify cleanliness in accordance with acceptance standards. 3.4 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of oxygen, nitrogen, and helium systems in accordance with Section 552 of 2.2 and Verify cleanliness in accordance with acceptance standards. 3.5 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of hydraulic systems in accordance with Section 556 of 2.2 and Verify cleanliness in accordance with acceptance standards. 3.6 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of fuel oil systems in accordance with Section 541 of Verify cleanliness in accordance with acceptance standards. 3.7 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of steam systems in accordance with Section 253 of Verify cleanliness in accordance with acceptance standards. 2 of 5 ITEM NO:
3 3.8 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of condensate systems in accordance with Section 255 of Verify cleanliness in accordance with acceptance standards. 3.9 Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of lube oil systems in accordance with Section 262 of Verify cleanliness in accordance with acceptance standards Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of fresh and potable water systems in accordance with Section 532 of Verify cleanliness in accordance with acceptance standards Accomplish the requirements of of 2.1 for each cleaning operation of refrigerant systems in accordance with the requirements of Verify cleanliness in accordance with acceptance standards Accomplish the requirements of of 2.1 for cleaning, flushing, and acceptance criteria of HP/LP steam drains in accordance with Section 534 of 4. NOTES: Verify cleanliness in accordance with acceptance standards. 4.1 This Standard Item does not apply to systems of nuclear-powered ships covered by NAVSEAINST , Steam Plant Cleanliness Control, or nuclear piping systems on nuclear-powered ships. 4.2 See Attachment A for Level II and Level III piping systems. 3 of 5 ITEM NO:
4 ATTACHMENT A CLEANLINESS LEVEL II AND III CLEANLINESS LEVEL II PIPING SYSTEMS: DIVERS AIR (NOTE 1) ELECTRONICS DISTILLED WATER COOLING (NOTE 1) HIGH PRESSURE AIR (NOTE 1) HYDRAULIC PIPING SYSTEMS (NOTE 1) LUBRICATING OIL SYSTEMS (NOTE 1) MISSILE HEATING AND COOLING REFRIGERANT SYSTEM (FREON AND LITHIUM BROMIDE) (NOTE 1) OXYGEN SYSTEM (NOTE 1) AIR CONDITIONING CHILLED WATER SYSTEM AUXILIARY STEAM SYSTEM CONDENSATE SYSTEM (NOTE 1) DIESEL FRESHWATER COOLING AIR FOR DIESEL CONTROL, VITAL AIR, ELECTRONICS SYSTEMS, ABC SYSTEMS AND PNEUMATIC CONTROL (NOTE 1) EXHAUST PIPING (STEAM) FEEDWATER SYSTEM (NOTE 1) POTABLE WATER SYSTEM (NOTE 1) FUEL SERVICE SYSTEM (NOTE 1) DISTILLATE PIPING SYSTEMS FUEL TRANSFER SYSTEM (NOTE 1) GASOLINE SYSTEM HIGH AND LOW PRESSURE DRAIN SYSTEM (NOTE 1) MAIN STEAM SYSTEM (NOTE 1) MEDIUM PRESSURE AIR (ABOVE 250 PSI AND BELOW 1500 PSIG) (NOTE 1) NITROGEN PIPING SYSTEM (NOTE 1) JP-5 PIPING SYSTEM OTHER SYSTEMS AS SPECIFIED BY THE DESIGN AGENT NOTE 1: SEE INDIVIDUAL GSO SECTIONS FOR ADDITIONAL SPECIAL CLEANING REQUIREMENTS CLEANLINESS LEVEL III PIPING SYSTEMS: AIR ESCAPE (TANK VENT) AIR CONDITIONING SEAWATER COOLING SYSTEM AFFF CONCENTRATE AND AFFF/SW SYSTEMS AUXILIARY SEAWATER SYSTEM CO2 SYSTEM 4 of 5 ITEM NO:
5 DIESEL EXHAUST SYSTEM DIESEL SEAWATER COOLING SYSTEM DISTILLING PLANT, BRINE OVERBOARD DISCHARGE SYSTEM DISTILLING PLANT, SEAWATER FEED SYSTEM ESCAPE PIPING (STEAM) FIREMAIN SYSTEM HALON MAIN SEAWATER COOLING SYSTEM PLUMBING SYSTEM SANITARY AND FLUSHING PIPING SYSTEM SHIP SERVICE LOW PRESSURE AIR SYSTEM (NON-VITAL) OTHER SYSTEMS AS SPECIFIED BY THE SUPERVISOR 5 of 5 ITEM NO:
NAVSEA STANDARD ITEM. 1.1 Title: Piping System Cleanliness Restoration (Non-Nuclear); accomplish
NAVSEA STANDARD ITEM ITEM NO: 009-107 DATE: 18 NOV 2016 CATEGORY: II 1. SCOPE: 1.1 Title: Piping System Cleanliness Restoration (Non-Nuclear); accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9AAO-AB-GOS-010,
NAVSEA STANDARD ITEM. 1.1 Title: Authorization, Control, Isolation, Blanking, Tagging, and Cleanliness; accomplish
NAVSEA STANDARD ITEM ITEM NO: 009-24 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Authorization, Control, Isolation, Blanking, Tagging, and Cleanliness; accomplish 2. REFERENCES: 2.1 Standard Items
NAVSEA STANDARD ITEM. 1.1 Title: Interference; remove and install LP , Submarine Safety (SUBSAFE) Requirements Manual
NAVSEA STANDARD ITEM ITEM NO: 009-23 DATE: 18 NOV 2016 CATEGORY: I 1. SCOPE: 1.1 Title: Interference; remove and install 2. REFERENCES: 2.1 Standard Items 2.2 0948-LP-045-7010, Material Control Standard
NAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM ITEM NO: 009-23 DATE: 17 JAN 2013 CATEGORY: I 1. SCOPE: 1.1 Title: Interferences; remove and install 2. REFERENCES: 2.1 Standard Items 2.2 0948-LP-045-7010, Material Control Standard
NAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM ITEM NO: 009-23 DATE: 17 JAN 2013 CATEGORY: I 1. SCOPE: 1.1 Title: Interferences; remove and install 2. REFERENCES: 2.1 Standard Items 2.2 0948-LP-045-7010, Material Control Standard
R & R IDENTIFICATION CO.
PRESSURE SENSITIVE HV FOR PIPE WITH OUTSIDE DIAMETER OF 6" AND OVER HOT WATER FOR PIPE WITH OUTSIDE DIAMETER OF 2-1/2" TO 6" COLD WATER FOR PIPE WITH OUTSIDE DIAMETER OF 1" TO 2-1/2" DOMESTIC DOMESTIC
MILITARY STANDARD SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS
NOTICE OF CHANGE INCH-POUND 19 February 2002 MILITARY STANDARD SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS TO ALL HOLDERS OF : 1. THE FOLLOWING PAGES
CHAPTER 51 MACHINIST'S MATE (MM) NAVPERS F CH-70
CHAPTER 51 MACHINIST'S MATE (MM) NAVPERS 18068-51F CH-70 Updated: April 2017 TABLE OF CONTENTS MACHINIST'S MATE, NUCLEAR POWER (MMN) SCOPE OF RATING GENERAL INFORMATION PROPULSION PLANT MECHANICAL OPERATOR
QUALITY ASSURANCE MANUAL FOR APPLICATORS OF ELASTOMERIC SHEET LININGS
QUALITY ASSURANCE MANUAL FOR APPLICATORS OF ELASTOMERIC SHEET LININGS 1.0 Purpose To establish a recommended quality assurance program for applicators of elastomeric sheet linings. 2.0 Scope This bulletin
NAVSEA STANDARD ITEM. 1.1 Title: Globe, Globe Angle, and Globe Stop Check Valve; repair
NAVSEA STANDARD ITEM ITEM NO: 009-51 DATE: 17 JAN 2013 CATEGORY: II 1. SCOPE: 1.1 Title: Globe, Globe Angle, and Globe Stop Check Valve; repair 2. REFERENCES: 2.1 S9086-CJ-STM-010/CH-075, Fasteners 2.2
NAVSEA STANDARD ITEM. 2.2 S9AAO-AB-GOS-010, General Specifications for Overhaul of Surface Ships (GSO)
NAVSEA STANDARD ITEM ITEM NO: 009-67 DATE: 18 NOV 2016 CATEGORY: I 1. SCOPE: 1.1 Title: Integrated Total Ship Testing; manage 2. REFERENCES: 2.1 Standard Items 2.2 S9AAO-AB-GOS-010, General Specifications
STANDARD PHRASEOLOGY SECTION A
STANDARD PHRASEOLOGY SECTION A 1. This section of standard phraseology contains the approved standard phrases to be used when invoking Category II Standard Items. The Standard Item number and title are
STANDARD PHRASEOLOGY SECTION B. 1. This section of standard phraseology is for general use in all disciplines.
STANDARD PHRASEOLOGY SECTION B 1. This section of standard phraseology is for general use in all disciplines. SHALL BE USED WHEN THE EXCEPTIONS LISTED IN 3.1 OF 009-23 ARE TO BE REMOVED/INSTALLED AS INTERFERENCES.
Bondstrand Marine Piping Systems
Bondstrand Marine Piping Systems Bondstrand Marine Pipe Systems Historically, ship owners have faced the grim reality of continuously replacing most metal piping because of severe corrosion. This results
NAVSEA STANDARD ITEM. 2.1 T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods
NAVSEA STANDARD ITEM ITEM NO: 009-55 DATE: 30 JUL 2010 CATEGORY: II 1. SCOPE: 1.1 Title: Regulating/Reducing Valve; repair 2. REFERENCES: 2.1 T9074-AS-GIB-010/271, Requirements for Nondestructive Testing
NAVSEA STANDARD ITEM. 1.1 Title: Maintaining Protection and Cleanliness from Non-Radioactive Operations; accomplish
NAVSEA STANDARD ITEM ITEM NO: 009-06 DATE: 30 JUL 2015 CATEGORY: I 1. SCOPE: 1.1 Title: Maintaining Protection and Cleanliness from Non-Radioactive Operations; accomplish 2. REFERENCES: 2.1 Standard Items
Standard Specifications for Ship Repair and Alteration Committee SSRAC
Standard Specifications for Ship Repair and Alteration Committee SSRAC History The Standard Specification for Ship Repair and Alteration Program (SSRAC) was established in 1970 to carry out the development,
NAVSEA STANDARD ITEM. 1.1 Title: Maintaining Protection and Cleanliness from Non-Radioactive Operations; accomplish
NAVSEA STANDARD ITEM ITEM NO: 009-06 DATE: 06 MAR 2018 CATEGORY: I 1. SCOPE: 1.1 Title: Maintaining Protection and Cleanliness from Non-Radioactive Operations; accomplish 2. REFERENCES: 2.1 Standard Items
C. heating turbine exhaust steam above its saturation temperature. D. cooling turbine exhaust steam below its saturation temperature.
P74 (B2277) Condensate depression is the process of... A. removing condensate from turbine exhaust steam. B. spraying condensate into turbine exhaust steam. C. heating turbine exhaust steam above its saturation
Stainless steel 444 HS tube. 6m lengths
Stainless steel 444 HS tube. 6m lengths SS630 Tube Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode Price ( ) ex VAT 15 x 1.0mm SS630 6 762 24000 5022050418678 8.78 18 x 1.0mm SS630 6 366 24001 5022050418753
NAVSEA STANDARD ITEM. 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other Mechanical and Electromechanical Measuring Instruments
NAVSEA STANDARD ITEM ITEM NO: 009-96 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Ball Valve; repair 2. REFERENCES: 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other Mechanical and Electromechanical
.1 marine diesel engine.1 approved in-service appropriate experience.2 marine steam turbine.2 approved training.3 marine gas turbine ship experience
STCW Code Table A-III/2 Specification of minimum standard of for chief engineer officers and second engineer officers on ships powered by main propulsion machinery of 3,000 kw propulsion power or more
FUNDAMENTALS OF PROCESS & MECHANICAL ENGINEERING
Training Title FUNDAMENTALS OF PROCESS & MECHANICAL ENGINEERING Training Duration 5 days Training Date Fundamentals Of Process & Mechanical Engineering 5 03 07 May $4,250 Dubai, UAE In any of the 5 star
.1 All equipment, controls and accessories to be compatible with system design, and matched to the steam boiler(s) by the boiler Manufacturer.
Construction of Sodium Hypochlorite and Chemical Storage Buildings Page 1 of 7 1. GENERAL 1.1 Scope.1 Boiler feed tank and pumps..2 Blowdown tanks..3 Water Softener System 1.2 Quality Assurance.1 All equipment,
Standard Operating (Installation) Procedures (SOP) For Manual Refractory Shotcreting Applications
Standard Operating (Installation) Procedures (SOP) For Manual Refractory Shotcreting Applications Colloidal silica bonded refractory applications utilizing pneumatic shotcreting include vessel or component
TOPIC: KNOWLEDGE: K1.01 [2.5/2.5]
![TOPIC: KNOWLEDGE: K1.01 [2.5/2.5]](/thumbs/96/127964750.jpg "TOPIC: KNOWLEDGE: K1.01 [2.5/2.5]")
KNOWLEDGE: K1.01 [2.5/2.5] P283 The transfer of heat from the reactor fuel pellets to the fuel cladding during normal plant operation is primarily accomplished via heat transfer. A. conduction B. convection
Recommendations are based on validity of above assumptions.
RST Assessment offukushima Daiichi Units, UNIT ONE ASSUMPTIONS: (based on input from multiple data source: JAIF, NISA, TEPCO, & GEH) Core Status: Core is contained in the reactor pressure vessel, reactor
CITY OF HAMILTON Codified Ordinance CHAPTER 941
CITY OF HAMILTON Codified Ordinance CHAPTER 941 Backflow and Backsiphonage Prevention 941.01 Definitions.1 941.02 Water system.3 941.03 Cross-connection prohibited.4 941.04 Survey and investigations.4
NAVSEA STANDARD ITEM. 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other Mechanical and Electromechanical Measuring Instruments
NAVSEA STANDARD ITEM ITEM NO: 009-52 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Relief Valve; repair 2. REFERENCES: 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other Mechanical and
Division II Contractors
Division II Contractors (d) "Sheet metal contractor" means a contractor whose services are unlimited in the sheet metal trade and who has the experience, knowledge, and skill necessary for the manufacture,
NAVSEA Documents. Topics. Scope. Learning Outcome. Relevant Documents. NAVSEA Basic Paint Inspector Training: NAVSEA Documents
NAVSEA Basic Paint Inspector Training: NAVSEA Documents NAVSEA Documents Topics l NAVSEA documents related to preservation of ships l Practical exercise on use of these document NAVSEA Basic Paint Inspector
MARCH 09, 2011 CIRCULAR NO. 11/11 TO MEMBERS OF THE ASSOCIATION. Dear Member:
MARCH 09, 2011 CIRCULAR NO. 11/11 TO MEMBERS OF THE ASSOCIATION Dear Member: US ENVIRONMENTAL PROTECTION AGENCY (EPA) AND COAST GUARD: AGREEMENT TO COORDINATE EFFORTS TO ENSURE COMPLIANCE WITH EPA VESSEL
How equipment reliability delivers low cost, energy efficient assets at plants around the world!
How equipment reliability delivers low cost, energy efficient assets at plants around the world! Background on topic Savings Opportunities Incorporating Energy Management to Equipment Reliability Q&A s
TOGA PRESENTATION REVIEW OF CASE STUDIES. Paul Boman,
TOGA PRESENTATION REVIEW OF CASE STUDIES Paul Boman, paul_boman@hsb.com October 8, 2014 HSB s TOGA History TOGA Transformer Oil Gas Analyst Registered trademark of Hartford Steam Boiler Inspection and
Proserv Flushing Unit - Offshore
Flushing Services PRODUCTION Proserv Flushing Unit - Offshore Proserv offers a wide range of various flushing units with diesel-engine drive and electrical drive options for sale and hire. We have different
Nuclear Services. Put Our Expertise To Work As Your Single Source For Industrial Cleaning And System Maintenance Solutions.
Nuclear Services Put Our Expertise To Work As Your Single Source For Industrial Cleaning And System Maintenance Solutions. Water Blasting Wet and Dry Vacuuming Pneumatic Hydro-Vacuum Excavation Digital
CONTENTS CO-GENERATING WATER-DESALINATING FACILITY POWERED BY SVBR-75/100 NUCLEAR REACTOR DESIGN ORGANIZATIONS INVOLVED IN THE PROJECT
CONTENTS CO-generating water-desalinating facility powered by SVBR-75/100 NUCLEAR 1 REACTOR Design organizations involved in the project 1 Layout of co-generating nuclear-powered water desalinating facility
Energy Efficient. & Cost Saving. Continuous Boiler Blowdown Package Heat Recovery Systems. 20 Models from 1,200 pph to 50,000 pph Capacity
Continuous oiler lowdown Package Heat Recovery Systems 20 Models from 1,200 pph to 0,000 pph Capacity Energy Efficient & Cost Saving Type HX - For Smaller oiler Systems Type HV - Vertical Type Type - Horizontal
CARRIAGE OF INTEGRAL REFRIGERATED CONTAINERS ON BOARD SHIPS
Guide for Carriage of Integral Refrigerated Containers on Board Ships GUIDE FOR CARRIAGE OF INTEGRAL REFRIGERATED CONTAINERS ON BOARD SHIPS MAY 2017 American Bureau of Shipping Incorporated by Act of Legislature
Energy Transfer in a Hydraulic System. Lecture (1) Hydraulic and Pneumatic Circuits 4th year Mech. power Engineering Dept.
15 Energy Transfer in a Hydraulic System 16 Control in a Hydraulic System The signal control section The power control section Drive section Signal input Signal processing Power control section Power flow
VVER-440/213 - The reactor core
VVER-440/213 - The reactor core The fuel of the reactor is uranium dioxide (UO2), which is compacted to cylindrical pellets of about 9 height and 7.6 mm diameter. In the centreline of the pellets there
Glassfiber Reinforced Epoxy Pipe Systems (GRE)
MARINE Glassfiber Reinforced Epoxy Pipe Systems (GRE) Version 01 Ballast water treatment system Seawater cooling systems Gland & flushing systems Firefight systems Black & grey water systems Condensate
SPECIFICATION FOR 20,000 GALLON LIQUID NITROGEN STORAGE TANK D-ZERO PROJECT FERMILAB G. T. MULHOLLAND G. STEPANEK
SPECIFICATION FOR 20,000 GALLON LIQUID NITROGEN STORAGE TANK D-ZERO PROJECT FERMILAB G. T. MULHOLLAND G. STEPANEK DECEMBER 1985 1.0 SCOPE LIQUID NITROGEN STORAGE TANK SPECIFICATION PAGE 1 ------------------------------------------
PTAC PROCESS TECHNOLOGY II - SYSTEMS. Last Reviewed: Page 1 of 10
Systems Overview Water Systems: Potable Water Fire Water Water Systems: Service/Utility Waste Water Storm Water 1. Describe how process industry facilities are divided into systems. Identify the types
Riviera Beach DIVISION 2. CROSS CONNECTION CONTROL
Riviera Beach DIVISION 2. CROSS CONNECTION CONTROL Sec. 20-231. Definitions. The following words, terms and phrases, when used in this division, shall have the meanings ascribed to them in this section,
BuildingName The Description of the Project P DOCUMENTS
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
NAVSEA STANDARD ITEM. 1.1 Title: Asbestos-Containing Material (ACM); control
NAVSEA STANDARD ITEM ITEM NO: 009-10 DATE: 30 APR 2018 CATEGORY: I 1. SCOPE: 1.1 Title: Asbestos-Containing Material (ACM); control 2. REFERENCES: 2.1 29 CFR 1915.1001, Occupational Safety and Health Standards
Valve Nest Filter with Time Clock Control Installation and Operation Manual
Valve Nest Filter with Time Clock Control Installation and Operation Manual Effective 5/24/12 Effective 5/24/12 Table of Contents Operating Data. 1 Pre-Installation Data... 2 Filter Parameters Installation
Cooling tower efficiency U2 Eco-efficiency resources for the food processing industry
Cooling tower efficiency U2 Eco-efficiency resources for the food processing industry Cool savings Many food processors operate cooling towers to meet the cooling needs of the factory. Cooling towers supply
ANSULITE ALCOHOL RESISTANT CONCENTRATE (ARC) 3% - 6% AFFF CONCENTRATE
ANSULITE ALCOHOL RESISTANT CONCENTRATE (ARC) 3% - 6% AFFF CONCENTRATE DESCRIPTION ANSULITE ARC 3%/6% Alcohol Resistant Concentrate is formulated from special fluorochemical and hydrocarbon surfactants,
CHAPTER 5 SEWAGE PUMPS AND LIFT STATIONS
15 October 1973 FM 5-163 CHAPTER 5 SEWAGE PUMPS AND LIFT STATIONS 5-1. General Pumps for lifting sanitary sewage, storm water, and plant-unit effluents are usually high-capacity, low-head types with large
Read Only Copy Not For Distribution. Chapter 17. Private Potable Water Supply Systems 17.1 GENERAL REGULATIONS 17.2 QUANTITY OF WATER REQUIRED
Chapter 17 Private Potable Water Supply Systems 17.1 GENERAL REGULATIONS 17.1.1 Applicability The regulations in this chapter apply to any private potable water supply system where plumbing fixtures are
NAVAL SEA SYSTEMS COMMAND What s New in Nonskid?
NAVAL SEA SYSTEMS COMMAND What s New in Nonskid? Mega Rust Norfolk, VA June 2017 Mr. Mark Ingle, P.E. SEA 05P2 (202) 781-3665 mark.w.ingle@navy.mil 1 TSN To Improve Flight Deck Performance TSN is only
Brown University Updated March 11, 2013 Facilities Design & Construction Standards
SECTION 01 17 90 UTILITY & CRITICAL SYSTEM CONNECTIONS AND INTERRUPTIONS PART 1 - GENERAL 1.1 SUMMARY: A. Brown University operates and maintains extensive campus and building utilities and distribution
Application Guide for Internal Flow Efficiency Coating
Jotapipe FC 407 Application Guide for Internal Flow Efficiency Coating Jotapipe FC 407 Date of Last Revision: March 2015 Page 1 of 6 Contents 1.0 Product Description... 2 2.0 Surface preparation and cleanliness...
CRYOGENIC FLUIDS CHAPTER 32
CHAPTER 32 CRYOGENIC FLUIDS SECTION 3201 GENERAL 3201.1 Scope. Storage, use and handling of cryogenic fluids shall comply with this chapter. Cryogenic fluids classified as hazardous materials shall also
Cyclone Technology protects analyzer systems for unrivalled reliability and tops productivity
Cyclone Technology protects analyzer systems for unrivalled reliability and tops productivity Standards Certification Education & Training Publishing Conferences & Exhibits Presenter Benson Loh 35 years
CRYOGENIC FLUIDS CHAPTER 32
CHAPTER 32 CRYOGENIC FLUIDS SECTION 3201 GENERAL 3201.1 Scope. Storage, use and handling of cryogenic fluids shall comply with this chapter. Cryogenic fluids classified as hazardous materials shall also
REBUILDING VESSELS LESS THAN 90 METERS (295 FEET) IN LENGTH AND BARGES OF ANY LENGTH
Guide for Rebuilding Vessels Less Than 90 Meters (295 Feet) in Length and Barges of Any Length GUIDE FOR REBUILDING VESSELS LESS THAN 90 METERS (295 FEET) IN LENGTH AND BARGES OF ANY LENGTH NOVEMBER 2014
Lecture (6) on. Schematic of a Thermal Power Plant. By Dr. Emad M. Saad. Mechanical Engineering Dept. Faculty of Engineering.
1 2 Lecture (6) on Schematic of a Thermal Power Plant By Dr. Emad M. Saad Mechanical Engineering Dept. Faculty of Engineering Fayoum University Faculty of Engineering Mechanical Engineering Dept. 2015-2016
THE REPUBLIC OF LIBERIA LIBERIA MARITIME AUTHORITY
Office of Deputy Commissioner of Maritime Affairs THE REPUBLIC OF LIBERIA LIBERIA MARITIME AUTHORITY Marine Notice FTP-002 12/16 TO: SUBJECT: ALL SHIPOWNERS, OPERATORS AND MASTERS OF LIBERIAN FLAGGED REEFER
Chapter 5 Water, Plumbing, and Waste
Chapter 5 Water, Plumbing, and Waste Parts 5-1 WATER 5-2 PLUMBING SYSTEM 5-3 MOBILE WATER TANK AND MOBILE FOOD ESTABLISHMENT WATER TANK 5-4 SEWAGE, OTHER LIQUID WASTE, AND RAINWATER 5-5 REFUSE, RECYCLABLES,
NUCLEAR TRAINING CENTRE COURSE 134 FOR ONTARIO HYDRO USE ONLY
NUCLEAR TRAINING CENTRE COURSE 134 FOR ONTARIO HYDRO USE ONLY NUCLEAR TRAINING COURSE COURSE 134 1 - Level 3 - Equipment & System Principles 4 - TURBINE, GENERATOR & AUXILIARIES Index 134.00-0 Objectives
Conceptual Facility Plans and Details. Appendix B
Conceptual Facility Plans and Details Appendix B Process Flow Diagrams and Equipment ³ ³ ³ ³ ³ PRELIMINARY / CONCEPTUAL 740 SOUTH SYNDICATE AVENUE THUNDER BAY, ONTARIO P7E 1E9 www.genivar.com TEL: 807
AP1000 European 15. Accident Analysis Design Control Document
15.2 Decrease in Heat Removal by the Secondary System A number of transients and accidents that could result in a reduction of the capacity of the secondary system to remove heat generated in the reactor
RIGHT ON COURSE EXPERTISE ON BOARD MARITIME OPERATIONS
RIGHT ON COURSE EXPERTISE ON BOARD MARITIME OPERATIONS PARTNER FOR SYSTEMATIC MORE EXPERTISE, BROAD SCOPE OF SERVICES Innovative systems partner MAHLE Industriefiltration develops and produces high-end
INDUSTRIAL SERVICES ON LINES COMPANY LTD. Your Chemical Cleaning Partner
INDUSTRIAL SERVICES ON LINES COMPANY LTD. Your Chemical Cleaning Partner WHO WE ARE Strategically situated in Jubail, eastern province of Saudi Arabia, Industrial Services Onlines Company Ltd is a division
NAVSEA STANDARD ITEM. 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other Mechanical and Electromechanical Measuring Instruments
NAVSEA STANDARD ITEM ITEM NO: 009-50 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Horizontal Swing Check Valve; repair 2. REFERENCES: 2.1 S9086-RJ-STM-010/CH-504, Pressure, Temperature and Other
Application Guide for Internal Flow Efficiency Coating Jotapipe FC 400
Jotapipe FC 400 Application Guide for Internal Flow Efficiency Coating Jotapipe FC 400 Date of Last Revision: February 2014 Page 1 of 6 Contents 1.0 Product Description... 2 2.0 Surface preparation and
CRYOGENIC FLUIDS CHAPTER 55
CHAPTER 55 CRYOGENIC FLUIDS SECTION 5501 GENERAL 5501.1 Scope. Storage, use and handling of cryogenic fluids shall comply with this chapter. Cryogenic fluids classified as hazardous materials shall also
WELDING AND ALLIED PROCESSES
WELDING AND ALLIED PROCESSES 1. SCOPE 1.1 Scope. This standard specification and appendices describe the general requirements for welding, fabrication, brazing, inspection, and associated processes on
NAVSEA STANDARD ITEM NUMERICAL INDEX
NAVSEA STANDARD ITEM NUMERICAL INDEX FY-18(CH-2) ITEM NO. 009-01 General Criteria; 009-02 Environmental Compliance Report for Material Usage at Naval Facility; 009-03 Toxic and Hazardous Substance; control
MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY. Subject: INSTRUCTIONS FOR THE IDENTIFICATION OF FACILITY PIPING SYSTEMS REVIEW DATE.
DAIMLERCHRYSLER MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY Subject: INSTRUCTIONS FOR THE IDENTIFICATION OF FACILITY PIPING SYSTEMS ISSUE DATE: 9/1/1992 EFFECTIVE DATE: 12/1/1988 REVIEW DATE. 1/22/2003
Pumps. s i n c e PUMPS. KRAL Pumps for Oil & Gas. European and American standards.
Pumps PREMIUM QUALITY KRAL Pumps for Oil & Gas. European and American standards. s i n c e 1 9 5 0 PUMPS www.kral.at Pumps KRAL AG a Reliable Partner for Global Players. High quality positive displacement
Filtration Solutions. In Naval Applications. Clean Fluids. Keep Running.
Filtration Solutions In Naval Applications Clean Fluids. Keep Running. Proven Solutions for Protecting Critical Shipboard Systems At Donaldson we are the acknowledged industry leader in the design, development
The following words and terms, when used in this article, shall have the following definitions, unless the context clearly indicates otherwise:
AVONDALE BACKFLOW ORDINANCE 24-1 Definitions. The following words and terms, when used in this article, shall have the following definitions, unless the context clearly indicates otherwise: "Approved"
Installation, Operating & Maintenance Instructions For Tri-Tech Medical Sleep Lab Panel Series
Manufacturer of Medical Gas Piping Equipment Installation, Operating & Maintenance Instructions For Tri-Tech Medical Sleep Lab Panel Series SLP-1 Sleep Lab Panel SLP-2 Sleep Lab Panel e6427rir 03/17/17
Generic New Construction Cost Estimating Libraries
Generic New Construction Cost Estimating Libraries Computerized Cost Estimating Computer-based tools to quickly formulate a cost estimate Manage cost data from central database Maintain current catalog
NAVSEA STANDARD ITEM. 1.1 Title: Asbestos-Containing Material (ACM); control
NAVSEA STANDARD ITEM ITEM NO: 009-10 DATE: 18 NOV 2016 CATEGORY: I 1. SCOPE: 1.1 Title: Asbestos-Containing Material (ACM); control 2. REFERENCES: 2.1 29 CFR 1915.1001, Occupational Safety and Health Standards
DURASHIELD 110 &
DURASHIELD 110 & 110-61 EFFECTIVE: 3/01/19 I. Scope A. This specification defines application requirements of DuraShield 110/110-61 plural-component, 100% solids, 1:1 volumetric mix ratio polyurethane
An Introduction to Plumbing and Gas Systems for Medical Facilities
An Introduction to Plumbing and Gas Systems for Medical Facilities J. Paul Guyer, P.E., R.A. Paul Guyer is a registered civil engineer, mechanical engineer, fire protection engineer, and architect with
HEAVY INDUSTRY PLANT WASTEWATER TREATMENT, RECOVERY AND RECYCLE USING THREE MEMBRANE CONFIGURATIONS IN COMBINATION WITH AEROBIC TREATMENT A CASE STUDY
HEAVY INDUSTRY PLANT WASTEWATER TREATMENT, RECOVERY AND RECYCLE USING THREE MEMBRANE CONFIGURATIONS IN COMBINATION WITH AEROBIC TREATMENT A CASE STUDY ABSTRACT Francis J. Brady Koch Membrane Systems, Inc.
N N O V A T I O N E F F I C I E N C Y Q U A L I T Y VTG. Vertical Turbine Generator
N N O V A T I O N E F F I C I E N C Y Q U A L I T Y VTG For more than 60 years the name Ruhrpumpen has been synonymous worldwide with innovation and reliability for pumping technology Ruhrpumpen is an
CONDENSATE-FEEDWATER-BOILER SYSTEM ON-LINE ANALYZERS. On-Line Analyzer Sample Point Alarm Points Comments
CONDENSATE-FEEDWATER-BOILER SYSTEM ON-LINE ANALYZERS On-Line Analyzer Sample Point Alarm Points 1. L.P. Heaters 2. H.P. Heaters 3. Boilers Feedwater Low 9.3 High 9.5 Boilers Low 8.7 High 9.7 Feedwater
Replacement Works for the Steam Generator and the Reactor Pressure Vessel Upper Head
Unit 2, Genkai Nuclear Power Plant Replacement Works for the Steam Generator and the Reactor Pressure Vessel Upper Head Replacement works for the above components were conducted at Unit 2 of the Genkai
8 th Annual Systems Engineering Conference Sponsored by the National Defense Industrial Association San Diego CA October 2005 SEC-8
8 th Annual Systems Engineering Conference Sponsored by the National Defense Industrial Association San Diego CA October 2005 1 Integrating MIL-STD-882 System Safety Products Into The Concurrent Engineering
NOVEL SCHEME FOR SMALL SCALE LNG PRODUCTION in POLAND. W.H. Isalski
NOVEL SCHEME FOR SMALL SCALE LNG PRODUCTION in POLAND W.H. Isalski Presentation Overview The history of gas de-nitrogenation in Poland Changes in feed gas Changes in market conditions Expanding market
Information on Status of Nuclear Power Plants in Fukushima
Information on Status of Nuclear Power Plants in Fukushima Japan Atomic Industrial Forum, Inc. Policy on information and compilation This JAIF-compiled information chart represents the situation, phenomena,
DURASHIELD 210 &
DURASHIELD 210 & 210-61 I. Scope A. This specification defines application requirements of DuraShield 210 & DuraShield 210-61 plural-component 100% solids, 2:1 volumetric mix ratio polyurethane to steel
December Illinois American Water Cross Connection Control Program
December 2007 Illinois American Water Cross Connection Control Program INDEX Page SECTION I PURPOSE..... 1 SECTION II DEFINITIONS..... 3 SECTION III BACKFLOW PROTECTION REQUIREMENTS.....6 SECTION IV BACKFLOW
PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
FRESH WATER GENERATORS ONBOARD A FLOATING PLATFORM
FRESH WATER GENERATORS ONBOARD A FLOATING PLATFORM P.K. TEWARI, R.K. VERMA, B.M. MISRA, H.K. SADHULKAN Desalination Division (Chemical Engineering Group), Bhabha Atomic Research Centre, Bombay, India Abstract
Joint Surface Preparation Standard. NACE No. 3/SSPC-SP 6 Commercial Blast Cleaning
Item No. 21067 Joint Surface Preparation Standard NACE No. 3/SSPC-SP 6 Commercial Blast Cleaning This NACE International (NACE)/SSPC: The Society for Protective Coatings standard represents a consensus
Waste Heat to Power (WHP) Technologies. Eric Maxeiner, PhD. May 24, 2017
Waste Heat to Power (WHP) Technologies Eric Maxeiner, PhD. May 24, 2017 Presentation Outline of WHP WHP Market : Thermoelectric Steam Organic Rankine Cycle (ORC) sco 2 power cycle Overview of WHP: Definitions
Backflow Prevention Program Revised:
Backflow Prevention Program Revised: Approved by Director OBJECTIVE: The purpose of this policy is to define the minimum requirements for all connections to the University potable water system. Compliance
Information on Status of Nuclear Power Plants in Fukushima
Information on Status of Nuclear Power Plants in Fukushima Japan Atomic Industrial Forum, Inc. Policy on information and compilation This JAIF-compiled information chart represents the situation, phenomena,
Marine Facilities for LNG Carrier Transfer Alternatives
2.3.3.2 Marine Facilities for LNG Carrier Transfer Alternatives Two alternatives were considered for the marine facilities to support the transfer of LNG between the LNG carriers and onshore storage tanks.
Design Theories of Ship and Offshore Plant
Lecture Note of Design Theories of Ship and Offshore Plant Design Theories of Ship and Offshore Plant Part I. Ship Design Ch. 2 Introduction to Offshore Plant Design Fall 2015 Myung-Il Roh Department of