New Measurement Engineering for Heating Technicians and Inspectors

Transcription

1 testo New Measurement Engineering for Heating Technicians and Inspectors A new dimension in speed and efficiency NEW! C hpa O 2 CO/H 2

2 testo A new dimension in speed and efficiency The new flue gas analyser generation offers heating technicians all the features required to competently carry out the inspection tasks at hand: the analyser has a special menu and automatic mean calculation. The course of the temperature during hot spot detection is shown in graphs on the display. Draught measurement is also 1 2 Highest availability and long life of wearing parts Faster and more effective The typical service life of Testo s own measurement cells is now more than three years. The Testo design eliminates the formation of condensate in the actual measurement cell. This and the special design of the gas paths in the instrument combined with the position of the condensate trap prevent blockages and increases service life considerably. The design layout of the gas paths and an additional filter mean that the gas pump is protected thus increasing service life. The lithium ion rechargeable batteries free from the memory effect and total discharge - are currently unbeatable in terms of service life. The service life of the rechargeable battery is more than six hours when the pump is operating. testo 330 has the added advantage that testo rechargeable batteries can be recharged outside the instrument as well in the instrument. The lithium ion rechargeable battery is very compact and can be quickly and easily changed. When changing probes - by quickly and simply attaching the probe or probe shaft - the analyser can automatically recognise the job and the corresponding measurement menu appears immediately. The probe can remain positioned in the flue during the zero phase of the measurement cells. testo 330 is calibrated in less than 30 seconds. Fuel, for example, can be selected at the same time and the analyser is then ready for use. The memory management function in the instrument facilitates easy and user-friendly structured representations of the data. The search function as well as the structuring of customer and measurement data can be carried out according to postcode, town, street, name or system number. The new testo 330 also has a USB interface as well as built-in IRDA interface. This makes it possible to transmit the results to the corresponding branch software.

3 shown in the same menu; the probe can remain positioned in the flue during the zero phase. This improves measurement accuracy when checking the systems and helps to save you time. CO switch-off can be carried out manually if necessary. 3 Increased safety The new testo opens up new opportunities for planning applications. The times in which an analyser suddenly lets the user down belong to the past. testo 330 s instrument diagnosis provides you with information about the qualitative status of functions and wearing parts. Included is the quality check on measurement cells, filter status, level display in the condensate trap, leak-proofness of instrument, pump capacity, rechargeable battery status and the date of the last maintenance. Your daily work is therefore easier to plan.

4 New upload and configuration software When developing the software, userfriendly operation and handling had top priority. Additionally, not only can data be uploaded, it can also be conveniently filed and managed. It is also possible to control the analyser via software when measuring online. Long life of wearing parts. The typical service life of the wearing parts for Testo s own measurement cells is now three years. The lithium ion rechargeable batteries free from the memory effect and total discharge are currently unbeatable in terms of service life.

5 4 5 More convenience and user-friendliness The service cover, which can be easily removed without any tools, makes for easy care and maintenance of the instrument. Changing the lithium ion rechargeable battery and measurement cell could not be easier. Since the calibration data is saved in the measurement cell, it can be changed in compliance with TÜV without the need for sample gas calibration. The condensate trap is easy to access and to empty. It is located just in front of the measurement cell in the housing. The new, very robust quick probe connection for all gas paths eliminates any confusion. The single cable cannot be bent, is indestructible and saves space. The menu-driven operational procedures in accordance with standards help you to avoid errors and save you time. The very large, backlit display is a perfect additional aid. The size of the display means you can switch from four to eight parameters. Totally robust instrument concept The particle filter absorbs contaminants at the points where they occur. For this reason, the filter cartridge is located in the probe handle for easy access. For applications in extreme conditions, such as highly contaminated burners, Testo s patented technology guarantees efficient measurements up to a CO measurement range of 30,000 ppm. The measurement cell is not subjected to any more strain than during normal measurements. The new testo 330 not only stands out on account of its distinctive and ergonomic design but also on account of its unique robust housing design. The material used acts as a builtin protection from impact and shock. The large backlit display is positioned slightly recessed in the housing for better protection.

6 The right accessories for every application. The probes The robust probe handle which fits nicely in your hand facilitates easy positioning. The probe has a quick connection function ensuring that all gas paths are connected while at the same time eliminating any confusion. The particle filter accommodated in the handle blocks out particles efficiently. Additionally, the probes require little or no maintenance and are easy to clean. Different lengths and diameters ensure a high flexibility level for all applications. When changing the probe, the probe shaft is simply attached to the probe handle and clicks into place. The multi-hole and dual wall clearance probe round off our wide range of flue gas probes. The ambient CO probe as well as the CO 2 probe are recognised automatically by the analyser and the measurement results immediately appear in their own graphically supported menu. Furthermore, the user-defined alarm limit is coupled with an audible signal. Measurements can be carried out in their entirety simultaneously with flue gas measurement. The gas leak protection probe which can be attached to the analyser also has a user-defined alarm limit. A warning signal is triggered if the limit is exceeded. The probe is also recognised automatically and the results are shown in a trend graph in their own menu.

7 The new versatile infrared printer The new testo printer cordless with infrared interface saves data for printing. This saves time since the analyser is ready for operation immediately after the data is transmitted. The printer can be used anywhere. New upload and configuration software When developing the software, user-friendly operation and handling had top priority. Additionally, not only can data be uploaded, it can also be conveniently filed and managed. It is also possible to control the analyser via software when measuring online.

8 At a glance The set for the heating technician Testo has put together a set for heating technicians in order to make selection easier for you. Of course, it is always possible to add to and supplement the set by selecting from the comprehensive range of accessories available. testo flue gas analyser incl. rechargeable battery and calibration protocol V mains unit for mains operation or recharging in analyser Modular flue gas probe, immersion depth: 300 mm, ø 8 mm CO multi-hole probe shaft suitable for the modular flue gas probe Combustion air temperature probe, 190 mm long Smoke tester incl. oil, soot sheets and reference scale Basic system case for analyser, probes and accessories testo at a glance testo at a glance Instrument diagnosis Automatic instrument leak test Rechargeable battery status display Sensor status display Monitoring of condensate trap level with FULL message Display of pump power (l/min.) Display of error status incl. description and diagnosis Display of last maintenance Display of instrument temperature Operating hour counter Additional measurement tasks T measurement, flow/return Ambient CO measurement Ambient CO 2 measurement Detection of gas leaks with gas leak detection probe P measurement for gas pressure Gas/oil flow rate measurement Automatic menu selection Recognition of connected probe Initialisation of pressure sensor for draught measurement without removal of probe The probe can remain in the flue during initialisation Memory management 400 measurement data records incl. object address and system number Several measurement data records per system number are possible Read in using barcode reader IRDA interface for data transfer to PDA/Notebook USB interface for data transfer to PC ZIV driver for all conventional branch software Additional features BImSchV menu with manual CO switch-off and qa mean value Calculated parameter: Flue gas dew point Graphics display Graphic hot spot detection Built-in impact protection with magnet, recessed display Protection class IP40 Rechargeable battery lifetime > 6 h with pump operating Rechargeable battery separate and rechargeable in instrument Adjustable alarm thresholds for ambient CO/CO 2 measurement TÜV approval / EN standard approved for O 2, CO 2, CO, NO, NO low, C, hpa Approved measurement cell interchange CO (adjustment without testing gas)

9 Technical Data Temperature Draught measurement Pressure measurement O 2 measurement CO measurement (H2 compensated) -40 to C ±0,5 C (0.0 to C) ±0,5 % of mv (remaining range) 0.1 C (-40 to 999,9 C) 1 C (remaining range) -40 to 40 hpa ±0.02 hpa or ±0.5 % of mv (-0.50 to hpa) ±0.03 hpa or ±0.5 % of mv (+0.61 to hpa) ±1.5 % of mv (+3.01 to hpa) 0.01 hpa 0 to 200 hpa ±0.5 hpa (0.0 to 50.0 hpa) ±1 % of mv (50.1 to hpa) ±1.5 % of mv (remaining range) 0.1 hpa 0 to 21 Vol. % 0.1 Vol. % ±0.2 Vol. % < 20 s 0 to 8000 ppm 1 ppm ±10 ppm or ±10% of mv (0 to 200 ppm) ±20 ppm or ±5% of mv (201 to 2000 ppm) ±10% of mv (2001 to 8000 ppm) < 40 s from 8000 ppm Display range 8000 to ppm (automatic dilution) 500 ppm Efficiency (Eta) Flue gas loss CO2 measurement Option: NO low measurement Option: NO measurement Ambient CO measurement (with CO probe) Gas leak measurement for combustible gases (with gas leak detection probe) 0 to 120 % 0.1 % 0 to 99.9 % 0.1 % Display range Measurement 0 to CO2 max 0.1 Vol. % ±0.2 Vol. % Digital calculation from O2 < 40 s 0 to 300 ppm 0.1 ppm ±2 ppm (0.0 to 40.0 ppm) ±5% of mv (remaining range) < 30 s 0 to 3000 ppm 1 ppm ±5 ppm (0 to 100 ppm) ±5% of mv (101 to 2000 ppm) ±10% of mv (2001 to 3000 ppm) < 30 s 0 to 500 ppm 1 ppm ±5 ppm (0 to 100 ppm) ±5% of mv (>100 ppm) Approx. 35 s Display range 0 to 10,000 ppm CH 4 / C 3 H 8 Signal Optical display (LED) audible display via buzzer Adjustment time t90 < 2 s * * * * Ambient CO 2 measurement (with ambient CO 2 probe) General Technical Data Memory Weight Dimensions Storage temp. Oper. temp. Display Power supply Warranty 0 to 1 Vol. % 0 to ppm ±(50 ppm ±2 % of mv) (0 to 5000 ppm) Approx. 35 s 400 Sites 600 g (without rechargeable battery) 270 x 90 x 65 mm -20 to +50 C -5 to +45 C Graphics display: 160 x 240 pixel Rechargeable block: 3.7 V / 2.2 Ah Mains unit: 6 V / 1.2 A Analyser/cells/probe 2 years, rechargeable battery 1 year IRDA printer Printer type Infrared-controlled thermal printer, adjustable contrast, graphics can be printed Reception radius Max. 2 m Dimensions 186 x 91 x 61 mm Weight 430 g incl. batteries Oper. temp. 0 to +50 C Storage temp. -40 to +60 C Power supply 4 round cell batteries, 1.5 V or NC rechargeable batteries *the larger value applies

10 Fax Order Form testo Set: Pro analysis for heating technicians Probes testo flue gas analyser incl. rechargeable battery and calibration protocol V mains unit for mains operation or recharging in analyser Modular flue gas probe, immersion depth: 300 mm, ø 8 mm CO multi-hole probe shaft suitable for the modular flue gas probe Combustion air temperature probe, 190 mm long Smoke tester incl. oil, soot sheets and reference scale Basic system case for analyser, probes and accessories Modular flue gas probes, available in 2 lengths, incl. positioning cone, NiCr-Ni thermocouple, 2.2 m hose and particle filter Flue gas probe 180 mm long, Ø 8 mm, Tmax 500 C Flue gas probe 300 mm long, Ø 8 mm, Tmax 500 C Flue gas probe 180 mm long, Ø 6 mm, Tmax 500 C Flue gas probe 300 mm long, Ø 6 mm, Tmax 500 C Instrument / Options / Upgrades Probe accessories testo flue gas analyser incl. rechargeable battery and calibration protocol Probe shaft 180 mm long, Ø 8 mm, Tmax 500 C Option: Fine draught measurement, 0.1 Pa, measurement range to 100 Pa (instead of the standard draught measurement) Option: Gas zeroing, Probe can remain in flue during initialisation Option: NO meas. cell, meas. range 0 to 3000 ppm, 1 ppm resolution On request Upgrade: NO meas. cell, meas. range 0 to 3000 ppm, 1 ppm resolution On request Option: NOlow meas. cell, meas. range 0 to 300 ppm, 0.1 ppm resolution Upgrade: NOlow meas. cell, meas. range 0 to 300 ppm, 0.1 ppm resolution Probe shaft 180 mm long, Ø 6 mm, Tmax 500 C Probe shaft 300 mm long, Ø 8 mm, Tmax 500 C Probe shaft 300 mm long, Ø 6 mm, Tmax 500 C Probe shaft 300 mm, Ø 8 mm, Tmax 1000 C Probe shaft 700 mm long, Ø 8 mm, Tmax 1000 C Flexible probe shaft 330 mm long, Ø 10 mm, Tmax 500 C Multi-hole probe shaft, 300 mm long, Ø 8 mm, for mean CO calculation Hose extension, 2.80 m, extension cable for probe and analyser Accessories Cone 8 mm, steel, with grip clamp and grip, Tmax 500 C V mains unit for mains operation or batt. recharging in analyser Cone 6 mm, steel, with spring clamp and grip, Tmax 500 C Spare rechargeable battery with recharging station Additional probes IRDA printer Spare thermal paper for printer (6 rolls), permanent ink Dual wall clearance probe Barcode reader to read in customer number on site Gas leak probe, available from December Barcode labels, self-adhesive (1200 off) Adhesive pockets (50 off) for printout, paper barcode labels Ambient CO probe Smoke tester with oil, soot sheet, for measuring soot in flue gas Ambient CO2 probe Hose connection set for separate gas pressure measurement Connection cable Differential temperature set consisting of 2 pipe clamp probes and adapter Combustion air temperature probe Spare particle filter (10 off) Combustion air temperature probe, immersion depth 300 mm testo 330 software with analysis and graphics functions, online measurement Combustion air temperature probe, immersion depth 190 mm USB connection cable, instrument to PC Combustion air temperature probe, immersion depth 60 mm ISO calibration certificate/flue gas Additional temperature probes Cases Mini ambient air probe Basic system case for analyser, probes and accessories Pipe clamp probe Basic system case with two levels for analyser, probes and additional accessories Product system case with small plastic boxes without contents, can be interlocked to basic system case Tools system case with tools section without content, can be interlocked to basic system case Quick-action surface probe Connection cable Universal system case w/o pockets, can be interlocked to basic system case Measurement case (leather) with drawers for instruments and accessories Spare measurement cells Spare O2 measurement cell Spare CO measurement cell (H2 compensated) Spare NOlow measurement cell 0 to 300 ppm Spare NO measurement cell 0 to 3000 ppm On request Sender Name Subject to change without notice. Company Department Address City Signature /hd/AC/A/