G30. Burke Coolants G30 fulfills the requirements of the following coolant standards:

Transcription

1 Page 1/6, in CoBranding partnership with BASF manufacturers of Glysantin, is an engine coolant based on ethyleneglycol that needs to be diluted with water before use. contains a corrosion inhibitor package based on organic acid salts (OAT coolant). is free of nitrites, amines, phosphates, silicates and borates. PROPERTIES protects engines against corrosion, overheating and frost. It effectively protects engines against corrosion and deposits in the cooling system with its vital parts, the coolant channels in the block and cylinder head, the radiator, the water pump and the heater core. fulfills the requirements of the following coolant standards: AS , ASTM D 3306, ASTM D 4985, BS 6580:2010, CUNA NC 95616, AFNOR NFR , ÖNORM V 5123, SAE J1034, SANS 1251:2005 and SH Furthermore, Glysantin G30, by BASF, is officially approved according to the following OEM standards: Audi / Bentley / Lamborghini / Seat / Skoda / VW TL 744 D/F DAF MAT MAN MAN 324 SNF MercedesBenz MBApproval Mini (Diesel motors) MTU MTL 5048 Porsche is also recommended for use in: Alfa Romeo (Built from 2005), Chrysler (Built from 2008), Citreon (Built from 1993), CNH (Built from 2014), Dacia (Built from 2005), Daihatsu (Built from 1979), Ferrari (Built from 2005), Fiat (Built from 2005), Ford (Built from 2008), Honda (Built from 1983), Hyundai (Built from 1982), Jaguar (Built from 1999), KIA (Built from 1991), Lancia (Built from 2005), Land Rover (Built from Page 1/6

2 Page 2/6 1998), Lexus (Built from 1994), Lotus (Built from 2000), Mazda (Built from 1977), MG Rover (Built from 1982), Mitsubishi (Built from 1982), Nissan (Built from 1982), Peugeot (Built from 1993), Renault (Built from 1985), Subaru (Built from 1977), Suzuki (Built from 1981), Toyota (Built from 1978), Volvo Truck (Built from 2006). MISCIBILITY The special advantages of will only be achieved when Burke Coolants G30 is used exclusively. Mixing with other Burke Coolant products or coolants of other producers is not recommended. Concentrate should be blended with water in a concentration amongst 33 to 60% by volume prior to infilling. The usage of a 50/50 ratio for the mixture of water and Burke Coolant is generally advisable. For preparation of the coolant it is recommended to use distilled or deionized water. In most cases tap water is also appropriate. Analysis values of the water may not exceed the following threshold values: Water hardness: Chloride content: Sulfate content: mmol/l max. 100 ppm max. 100 ppm Chemical nature Ethylene glycol with corrosion inhibitors Appearance Clear liquid without solid contaminants Physical data Density, 20 C Viscosity, 20 C Refractive index, 20 C Boiling point Flash point ph value g/cm mm 2 /s > 160 C > 120 C DIN DIN DIN ASTM D 1120 DIN ISO 2592 ASTM D 1287 Page 2/6

3 Page 3/6 Reserve alkalinity Water content 8 11ml max. 3 % ASTM D 1121 DIN Stability Inhibitor stability after 168 h no flocculation VW TL 774 D/F Hard water stability after 10 days no flocculation VW PV 1426 Freezing Point Freezing point ASTM D vol % solution 33 vol % solution below 38 C below 18 C Frost Protection of Foaming characteristics 33 vol % solution 33 vol % solution max. 20 ml/max. 5ml max. 50 ml/3 s VW TL 774D/F ASTM D 1181 Electrical conductivity 3050 vol % solution approx. 4 ms/cm, at 23 C ASTM D 1125 Page 3/6

4 Page 4/6 Glassware Corrosion Test ASTM D 1384 Metal coupons typical weight loss mg/coupon ASTM D 3306 limit mg/coupon Copper Solder Brass Steel Cast iron Cast aluminium 0.8 *) 1.2 *) 0.9 *) *) 30 max 30 max *) remark: negative values mean a weight gain. Simulated ServiceTest ASTM D 2570 Metal Coupons Copper Solder Brass Steel Cast iron Cast aluminium typical weight loss mg/coupon 2.8 *) 1.7 *) 1.4 *) 0.3 *) *) ASTM D 3306 limit mg/coupon 60 max 60 max *) remark: negative values mean a weight gain. Cavitation Erosion Corrosion Test ASTM D 2809 Rating ASTM D 3306 limit Rating Aluminium water pump 9 8 min Page 4/6

5 Page 5/6 Heat Transfer Corrosion Test ASTM D 4340 typical corrosion rate mg/cm 2 /week ASTM D 3306 limit mg/cm²/week G AlSi6Cu max Polarization Resistance NF R limit NF R Aluminium: 1.2 * 10 6 Ω*cm² > 10 6 Ω*cm² QUALITY CONTROL The above data represents average values at the time of going to press of this technical information. It cannot be regarded as specified data. Specified product data is issued as a separate product specification. STORAGE STABILITY has a shelf life of at least three years when stored in originally closed, airtight containers at temperatures of maximum 30 C. Do not use galvanized containers for storage. COLOUR is usually available in redviolet. SAFETY When using this product, the information and advice given in our Safety Data Sheet should be observed. Due attention should also be given to the precautions necessary for handling chemicals. Page 5/6

6 Page 6/6 NOTE The data contained in this publication is based on our current knowledge and experience. In view of the many factors that may affect processing and application of our product, this data does not relieve processors from carrying out their own investigations and tests; neither does this data imply any guarantee of certain properties, nor the suitability of the product for a specific purpose. Any descriptions, drawings, photographs, data, proportions, weights, etc. given herein may change without prior notice and does not constitute the agreed contractual quality of the product. It is the responsibility of the recipient of our products to ensure that any proprietary rights and existing laws and legislation are observed. Company: S.J. Burke & Company Limited t/a Burke Coolants Milltown Shopping Park, Rathnew, Co. Wicklow, Ireland Telephone: +353 (0) Website address: Page 6/6