Fine-Blend PP-g-MAH Version:3.0 Revision Date:10/6/2014

Transcription

1 1. PRODUCT AND COMPANY IDENTIFICATION Product name: PP-g-MAH resin Grade names: Fine Blend TM CMG5001, CMG9801, CMG9801-GS, CMG5001-T Manufacturer: Nantong Sunny Polymer New Materials Technology Co., Ltd. Address: NO.3078 Humin RD, Minhang, Shanghai, , China TEL: FAX: Emergency contact: HAZARDS IDENTIFICATION Most important danger hazardous property Potential Health Effects: Eye: Dust and process vapors may irritate eye Skin: Exposure to molten resin may cause thermal burns Inhalation: Dust and process vapors may cause respiratory tract irritation Ingestion: Not applicable GHS classification: It can't be classified for data shortage. GHS label element: Not applicable 3. COMPOSION/INFORMATION ON INGREDIENTS Component Concentration CAS No. Maleated Polypropylene wt% Additive agent etc. 0-1% Secret Note: This product do not contains regulated components. 1 / 5

2 4. FIRST AID MEASURES Eye contact: Flush with plenty of water. Skin contact: Wash with water and mild soap. Inhalation: Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call a physician. Ingestion: Drink enough warm water, promote emesis. Call a physician. 5. FIREFIGHTING MEASURES Suitable extinguishing media: Water, Foam, Dry chemical, Carbon dioxide (CO 2 ). Firefighting Instructions: Wear self-contained breathing apparatus (SCBA). 6. ACCIDENTAL RELEASE MEASURES Land spill: Pellet represent a slipping hazard, scoop and sweep up or use industrial vacuum cleaner. Water Spill: Recover spilled material and place in suitable containers for recycle or disposal. Consult an expert on disposal of recovered material and ensure conformity to federal, state and local disposal regulations. Individual precautions: Ventilate the area. Be careful not to slip on loose pellets. Environmental precautions: Try to prevent the material from entering drains or water courses. Do not contaminate surface water. 7. HANDLING AND STORAGE Store away from oxidizing materials in a cool, dry place with adequate ventilation. Keep away from open flame and heat. Material will burn if exposed to fire. The suitable storage temperature range between 0 C to 40 C. Ground transfer equipment to avoid static discharge. Material should be stored in packaging similar to that which it was originally 2 / 5

3 shipped in. 8. EXPOSURE CONTROLS /PERSONAL PROTECTION Provide personal protective equipment. Ventilation equipment is necessary in workplace. Respiratory protection: Dust mask recommended. Eye/face protection: Safety glasses with side shields. Skin protection: Cloth gloves when working with molten plastic. Other protection: Smoking, eating, drinking water are prohibited in workplace. Avoid drinking stimulant before work. Changing clothes and showering after work. Prior to employment and periodic physical examination is necessary. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Solid Appearance/odor: Pellets with minimal odor Melting point/range: C Specific gravity (H 2 O=1): 0.85~0.98(g/cm 3 ) Thermal decomposition: > 270 C PH: N/A Solubility in Water (20 C): Negligible 10. STABILITY AND REACTIVITY Stability: The product is stable under ambient conditions. Conditions to avoid: Avoid heating for prolonged periods above the recommended upper processing limit. Heat, flames and sparks. Avoid dust formation and electrical charging. Materials to avoid: Strong oxidizing agents. Hazardous decomposition products: Carbon dioxide (CO 2 ), Carbon monoxide (CO), Hydrocarbons, Smoke. Decomposition can occur below the recommended processing 3 / 5

4 temperature limit. Decomposition products may vary in nature depending upon actual conditions, eg. availability of oxygen, temperature and presence of other materials. Hazardous reaction: Polymerization will not occur. 11. TOXICOLOGICAL INFORMATION High toxicity: None Sensitization: May irritate skin. May cause sensitization by skin contact. May cause sensitization by inhalation. Carcinogenicity/mutagenicity/reproductive toxicity: Maleic anhydride is not listed by ACGIH, IARC, NIOSH, NTP, or OSHA. 12. ECOLOGICAL INFORMATION Additional ecological information:no data is available on the product itself. Toxicity is expected to be low based on insolubility in water. 13. DISPOSAL CONSIDERATIONS Dispose of in accordance with local environmental regulations. 14. TRANSPORT INFORMATION According to the international and national laws that regulate road, train, air and water transport, this product is not considered dangerous. Refer to Section 7 for material handling and storage during transport. 15. REGULATORY INFORMATION Not a hazardous substance or preparation according to EC-directives 67/548/EEC or 1999/45/EC. Labeling according to EC regulations:the product does not require a hazard warning label 4 / 5

5 in accordance with EC directives. SARA Hazard Notification: Section 302 Extremely Hazardous Substances:None Section 313 Toxic Chemical(s):Maleic anhydride is subject to SARA 313 reporting requirements. 16. OTHER INFORMATION Caution do not use Fine-Blend materials in applications involving implantation within the body; direct or indirect contact with the blood pathway; contact with bone, tissue, tissue fluid or blood; or prolonged contact with mucous membranes. Fine-Blend materials are not designed or manufactured for use in implantation in the human body or in contact with internal body fluids or tissues. Fine-Blend will not provide to customers making devices for such applications any notice, certification or information necessary for such medical device use required by FDA regulation or any other statute. Fine-Blend makes no representation, promise, express warranty or implied warranty concerning the suitability of these materials for use in implantation in the human body or in contact with internal body tissues or fluids. 5 / 5