1. TECHNICAL DATA LIGHT FITTING REFLECTOR Polycarbonate tube of 4 mm. thickness Laquered steel painted white END CAPS Aluminium 2030 (polyester paint RAL 7047) POWER SOURCE LAMP TYPE 220-240V, 50/60Hz T8 IP PROTECTION IP 66 INSULATION CLASS Class I WORK TEMPERATURE -20 ºC to +55 ºC ACCESORIES INCLUDED ATEX MARK CABLE ENTRY ATEX CERTIFICATE 2 steel zinc clamps with rubber protection and 2 eyebolts Holders. II 2GD Ex d IIB+H2 T6 Gb Ex tb IIIC T85ºC Db M25 thread (2 entries). GLAND valid for NON ARMOURED CA- BLE INERIS 14ATEX0064X 2. PICTURE PAGE 1/09
3. DIMENSIONS & WEIGHT A 208 190 150 B C 1 TUBE / 2 TUBES WATTS (W) A B C PACKING (Units) 58 1537 1565 1659 1 4. AVAILABLE POWERS 1 TUBE / 2 TUBES WATTS (W) ELECTRONIC DIMMABLE 58 PAGE 2/09
5. SPECIAL ACCESSORIES 5.1. CABLE GLANDS EEx d VALID FOR NON ARMOURED CABLE II 2 GD EEx d IIC T6 THREAD SIZE DIMENSIONS (mm) Ø OVERAL (mm) METRICS PG. NPT GAS CONE A B C D MÍN. MÁX. TYPE M-25 x 1,5 16 21 3/4 1 3/4 1 35 39 42 15 7 10 A M-25 x 1,5 16 21 3/4 1 3/4 1 35 39 42 15 9 12 B M-25 x 1,5 16 21 3/4 1 3/4 1 35 39 42 15 11 14 C M-25 x 1,5 16 21 3/4 1 3/4 1 35 39 42 15 13 16 D M-25 x 1,5 16 21 3/4 1 3/4 1 35 39 42 15 15 18 E 5.2. PLUG EEx d II 2 GD EEx d IIC T6 THREAD SIZE DIMENSIONS (mm) METRICS A B C M-25 15 10 30 Important: for each light, 1 plug and cable gland. If installed in a continuous line, 2 cable glands. PAGE 3/09
6. ATEX MARKIED NOMENCLATURE PROTECTION MODE GROUP TEMPERATURE CLASS II 2 DG Ex d IIC T6 Ex td A21 IP66 T85ºC DEVICE CATEGORY PROTECTION MODE ZONE IP PROTECTION TEMPERATURE CLASS ATEX ZONE CLASSIFICATION GROUP II FIXTURES: ABOVE GROUND INDUSTRIES ZONE CATEGORY EXPLOSIVE ENVIRONMENT PRESENCE Zone 0 Zone 20 Zone 1 Zone 21 1G (gases and vapors) 1D (powders) 2G (gases and vapors) 2D (powders) Constant, permanent. Occasional, frequent. Zone 2 Zone 22 3G (gases and vapors) 3D (powders) Never in normal service, only for short periods of time. GROUP I FIXTURES: MINES WITH FIRE-DAMP M1 M2 Presence (methane, dust) Presence risk (methane, dust) PAGE 4/09
PROTECTION MODES SYMBOL PROTECTION TYPE ZONE d Explosion proof 1,2 e Increased security 1,2 ia Intrinsic security 0,1,2 ib Intrinsic security 1,2 o Oil inmersion 2 p Pressurized 1,2 q Below sand 1,2 m Encapsulated 1,2 n Antisparks 2 GROUPS II CLASSIFICATION OF GASES AS YOUR TEMPERARUTA OF IGNITION ( * ) GASES I Methane (fire-damp) A B C Acetone Acetic acid Ammonia Ethane Methylene chloride Methane (CH 4 ) Carbon oxide Propane N-Butane N-Butyl N-Hexane Acetaldehyde ethyl ether Ethyl nitrite Ethyl Ethyl oxide Sulfur Hydrogen Acetylene (C 2 H 2 ) Carbon Sulfur (CS 2 ) Hydrogene (H 2 ) TEMPERATURE CLASSES T1 T2 T3 T4 T5 T6 PAGE 5/09
TEMPERATURE CLASSES TEMPERATURE CLASSES MAX. SURFACE TEMPERATURE (ºC) T1 450 T2 300 T3 200 T4 135 T5 100 T6 85 * The material marked as IIB suited to applications requiring material marked as IIA and IIC adapted for IIA and IIB. PAGE 6/09
8. PHOTOMETRY 1 tube light fitting. 2 tubes light fitting. PAGE 7/09
9. APPLICATIONS The light fitting of Airfal is designed to operate in environments that can be formed or an explosive atmosphere being present according to the ATEX directive 94/9/EC. The ITC-BT-29 BOE No. 224, based on R.D. 400/1996 establishes the hazardous locations where products must be installed with ATEX: Locations where volatile flammable liquid transfer from one container to another. Garages and car repair shops. It excludes garages of private use for parking of 5 vehicles or less. Interiors of paint booths where spray systems are used and their immediate environment when using solvents. Dries of material with inflammable solvents Places of extraction of fats and oils that use inflammable solvents. Places with warehouses of inflammable opened liquids or that could be opened. Zones of laundries and dry cleaner's shops in which inflammable liquids are used. Rooms of fuels. Facilities where they take place, manipulate, store or consume inflammable gases. Pump rooms and / or compressor flammable liquids and gases. Interiors of refrigerators and freezers in which inflammable matters are stored in opened containers, easily perforables or with slightly consistent closings Any other emplacement where there exists risk of explosion or of fire due to the presence of inflammable substances. * For more information contact the technical department. PAGE 8/09
10. VERSION LED TUBES 10.1 DIMENSIONS AND OTHER INTEREST DATA. A 208 190 150 B C LED 1 TUBE / 2 TUBES TUBE LED LENGHT (W) A B C PACKING (Units) 600 626 654 748 1 1.200 1235 1263 1357 1 1.500 1537 1565 1659 1 All the accesories can be use for the LED version (Cableglands, plug, ), except emergency kits. The photometry depends on the LED tube to be installed. PAGE 9/09