A2LA has accredited Brackenridge, PA for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 20 th day of February 2015. President & CEO For the Accreditation Council Certificate Number 3109.01 Valid to January 31, 2017 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1300 Pacific Avenue Natrona Heights, PA 15065-1147 Christopher Napoli Phone: 724-994-9802 / 724-226-5635 Fax: 724-226-5856 MECHANICAL Valid To: January 31, 2017 Certificate Number: 3109.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on armor, stainless steel, nickel-base, cobalt-base and titanium sheet, strip and plate products: Bending Hardness Brinell Hardness (3000 kg) Rockwell Hardness (B, C, 15N, 15T, 30N, 30T) ASTM E290 ASTM E10 ASTM E18 Metallographic Evaluation Grain Size ASTM E112 Inclusions ASTM E45 Method A Macro-etch ASTM E340 Microhardness ASTM E384 Knoop: 200 g, 500 g Vickers: 200 g to 10 kg Pitting and Crevice Corrosion ASTM G48, A923 Practices A and C Salt Spray ASTM B117 Stress Rupture ASTM E139 Susceptibility to Stress Corrosion Cracking ASTM G30 Susceptibility to Intergranular Corrosion ASTM G28 Susceptibility to Intergranular Attack ASTM A262 Practices A, B, C, and E; ISO 3651-2, ISO 3651-1 Tensile Test ASTM E8; EN-ISO 6892-1 Lab Heat Treatment AMS 2750 Surface Roughness ASME B46.1 Section 3 Cup Test ASTM E643; EN-ISO 20482 (A2LA Cert. No. 3109.01) 02/24/2015 Page 1 of 1
A2LA has accredited Brackenridge, PA for technical competence in the field of Chemical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 20 th day of February 2015. President & CEO For the Accreditation Council Certificate Number 3109.02 Valid to January 31, 2017 For the tests to which this accreditation applies, please refer to the laboratory s Chemical Scope of Accreditation.
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1 1300 Pacific Avenue Natrona Heights, PA 15065-1147 Christopher Napoli Phone: 724-994-9802 / 724-226-5635 Fax: 724-226-5856 CHEMICAL Valid To: January 31, 2017 Certificate Number: 3109.02 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on armor, stainless steel, nickel-base, cobalt-base and titanium sheet, strip and plate products: Metallurgical Testing Direct Current Plasma (DCP) Iron Base: (Mn, P, Si, Al, Mo, Cu, Nb, Ta, V, Ti, W, Sn, B, Ca, Mg, Zn, Zr, Cd, Ce, La, As) Nickel Base: (Mn, P, Si, Al, Mo, Cu, Nb, Ta, V, Co, Ti, W, Sn, Pb, B, Ca, Mg, Zn, Zr, Cd, Ce, La) Titanium Base: (Mn, Si, Cr, Ni, Al, Mo, Cu, V, Sn, B, Fe, Zr, Y, Pd) Cobalt Alloys (Mn, P, Si, Al, Mo, Cu, Nb, Ta, V, Co, Ti, W, Sn, Pb, B, Ca, Mg, Zn, Zr, Cd, Ce, La) Graphite Furnace Atomic Absorption (GFAA) (Sn, Pb, Cd, Bi, Se, Ag, Te, Tl) Inductively Coupled Plasma (ICP) (Mn, Si, Cr, Ni, Al, Mo, Cu, V, Sn, B, Fe, Zr, Y) Optical Emission (OES) (Al, Ti, Sn, B, Ta) Combustion Elemental Analysis Carbon and Sulfur by Infrared Nitrogen, Oxygen, and Hydrogen by Inert Fusion- LECO (C, S, N, O, H) (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Sn, Ta, Zr) Nickel Alloys: (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Sn, Fe, Ta, Zr) Cobalt Alloys: (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Sn, Fe, Ta, Zr) ASTM E1097; WET 01 ASTM E1184; WET 03 ASTM E1479; WET 04 ASTM E1019; ASTM E1447 1 This accreditation covers testing performed at the main laboratory listed above, and the satellite laboratories listed below. (A2LA Cert. No. 3109.02) 02/24/2015 Page 1 of 2
950 Tenth Street Midland, PA 15059 Optical Emission (OES) (Al, Sn, B, W, Ti) Combustion Elemental Analysis Carbon and Sulfur by Infrared Nitrogen by Inert Fusion- LECO (C, S, N, O) (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, Sn) ASTM E1019 Route 981 North Latrobe, PA 15650 Optical Emission (OES) (Al, Sn, B) Combustion Elemental Analysis Carbon and Sulfur by Infrared Nitrogen by Inert Fusion- LECO (C, S, N, O) (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W) Nickel Alloys: (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Fe) ASTM E1019 100 River Road Brackenridge, PA 15014 Optical Emission (OES) (Al, Sn, B) Combustion Elemental Analysis Carbon and Sulfur by Infrared Nitrogen and Oxygen by Inert Fusion- LECO (C, S, N, O) (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Sn) Nickel Alloys: (Mn, P, Si, Cr, Ni, Al, Mo, Cu, Nb, V, Ti, Co, W, Sn, Fe) ASTM E1019 (A2LA Cert. No. 3109.02) 02/24/2015 Page 2 of 2
A2LA has accredited New Bedford, MA for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 15 th day of January 2015. President & CEO For the Accreditation Council Certificate Number 3109.03 Valid to January 31, 2017 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1357 East Rodney French Blvd. New Bedford, MA 02742 David Shaner Phone: 508 984 2256 Fax: 508 984 8904 MECHANICAL Valid To: January 31, 2017 Certificate Number: 3109.03 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on stainless steels, titanium, carbon steels, and nickel alloys: Bending ASTM E290 Metallographic Evaluation Grain Size Susceptibility to Intergranular Attack ASTM E112 ASTM A262 Practice E; ISO 3651-2 Method A Microhardness Vickers (100 gf, 300 gf, 500 gf, 1000 gf) Surface Roughness ASTM E384 ASME B46.1 Section 3; LP-04 Tensile Test (5000 lbs Flat Specimens) ASTM E8/E8M; ISO 6892-1 Lab Heat Treatment AMS 2750 (A2LA Cert. No. 3109.03) 01/15/2015 Page 1 of 1