MicroVantage MAN Series Nylon 66 Membrane Filter Cartridges Absolute retention ratings from. to.65 microns Nylon 66 membranes provide electropositive charge to enhance particle removal through electrokinetic adsorption 7.2 square feet (.67 m2) of media surface area per ten inch length for optimal performance MAN grade cartridges are flushed and dried to ensure reliable performance in critical applications Rigid, molded polypropylene cage protects pleated media and strengthens structural stability Manufactured in a state-of-the-art white room and Class, clean room for high purity Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics. Available in standard lengths and end cap configurations to fit most filter housings Produced up to inches in length ( inch modules) Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Specifications & Operating Parameters Pore Sizes.,.2,.5,.65 microns absolute retention Nominal Lengths 9.75" (2.7 cm), " (25. cm), 2" (5.8 cm), 3" (76.2 cm), " (.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter." (2.5 cm) Media Surface Area 7.2 sq.ft. (.67 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Nylon 66 Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure 75 psid @ 7 F (5.2 bar @2 C), psid @76 F (2.8 bar @ 8 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop. µm 3 2.2 µm.5 µm.65 µm 2 6 8 Gallons per Minute GPM This chart represents the typical water flow per " cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, P of the housing becomes more apparent. Ordering Guide (Example: MAN.2-SS-E) MAN.2 S S E PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET/O-RING GRADE OPTION MAN..2.5.65 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPDM S = Silicone V = Viton T = Teflon encapsulated Viton (O-ring only) G = General B = Beverage E = Electronic HT = High Temperature* * High Temperature construction (cage, core, end caps): Maximum Temperature 2 F (93.3 C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: MAN.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage MAS-B Series Beverage Grade Polyethersulfone Membrane Filter Cartridges Absolute retention ratings from. to.2 microns 7.2 square feet (.67 m2) of media surface area per ten inch length for optimal performance Fully integrity tested to ensure reliable performance in critical applications % flushed with 8 megohm DI water for low extractables Rigid, molded cage protects pleated media and strengthens structural stability Manufactured in a Class, Clean Room environment for high purity Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics Available in standard lengths and end cap configurations to fit most filter housings Produced up to inches in length ( inch modules) Applications Food & Beverage Malt Beverages Beer RO Pre/Post Filtration Wine Bottled Water Process Water Water & Wastewater Specifications & Operating Parameters Pore Sizes.,.2,.5,.65,.8,.,.2 microns absolute retention Nominal Lengths 9.75 (2.7 cm), (25. cm), 2 (5.8 cm), 3 (76.2 cm), (.6 cm) Outside Diameter 2.67 (6.78 cm) Inside Diameter. (2.5 cm) Media Surface Area 7.2 sq.ft. (.67 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Polyethersulfone Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure 75 psid @ 7 F (5.2 bar @2 C), psid @76 F (2.8 bar @ 8 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop Integrity Testing 3. µm 2.5.2 µm PORE SIZE AIR DIFFUSION RATE 2.5.5.5 µm.65 µm.8 µm. µm.2 µm. μm.2 μm.5 μm.65 μm.8 μm. μm.2 μm 3cc/min@8psi 3cc/min@35psi 3cc/min@2psi 3cc/min@5psi 3cc/min@2psi 3cc/min@8psi 3cc/min@7psi Per " length water wetted membrane 2 6 8 GALLONS PER MINUTE GPM This chart represents the typical water flow per cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, P of the housing becomes more apparent. Ordering Guide (Example: MAS.2-SS-B) MAS.2 S S B PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET/O-RING GRADE OPTION MAS..2.5.65.8..2 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPDM S = Silicone V = Viton T = Teflon encapsulated Viton (O-ring only) B = Beverage HT = High Temperature* * High Temperature construction (cage, core, end caps): Maximum Temperature 2 F (93.3 C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: MASB.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage MAS-E Series Electronic Grade Polyethersulfone Membrane Filter Cartridges Absolute retention ratings from.3 to.65 microns 7.2 square feet (.67 m2) of media surface area per ten inch length for optimal performance Fully integrity tested to ensure reliable performance in critical applications % flushed with 8 megohm DI water to less than 5 ppb TOC Rapid rinse-up to 8 megohm resistivity and low extractables for use in ultrapure water Manufactured in a Class, Clean Room environment for high purity Rigid, molded cage protects pleated media and strengthens structural stability Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics Available in standard lengths and end cap configurations to fit most filter housings Produced up to inches in length ( inch modules) Applications Semiconductor Process Water RO Pre/Post Filtration Microelectronics DI Water Water & Wastewater Specifications & Operating Parameters Pore Sizes.3,.,.2,.5,.65 microns absolute retention Nominal Lengths 9.75" (2.7 cm), " (25. cm), 2" (5.8 cm), 3" (76.2 cm), " (.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter." (2.5 cm) Media Surface Area 7.2 sq.ft. (.67 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Polyethersulfone Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure 75 psid @ 7 F (5.2 bar @2 C), psid @76 F (2.8 bar @ 8 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop Integrity Testing 8.3 µm PORE SIZE AIR DIFFUSION RATE 6 2. µm.2 µm.5 µm.65 µm.3 μm. μm.2 μm.5 μm.65 μm 3cc/min@6psi 3cc/min@8psi 3cc/min@35psi 3cc/min@2psi 3cc/min@5psi Per " length water wetted membrane 2 6 8 GALLONS PER MINUTE GPM This chart represents the typical water flow per cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, P of the housing becomes more apparent. Ordering Guide (Example: MAS.2-SS-E) MAS.2 S S E PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET/O-RING GRADE OPTION MAS.3..2.5.65 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPDM S = Silicone V = Viton T = Teflon encapsulated Viton (O-ring only) E = Electronic HT = High Temperature* * High Temperature construction (cage, core, end caps): Maximum Temperature 2 F (93.3 C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: MASE.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage MAS-G Series General Grade Polyethersulfone Membrane Filter Cartridges Absolute retention ratings from.3 to.2 microns 7.2 square feet (.67 m2) of media surface area per ten inch length for high throughput and longer service life Fully integrity tested to ensure reliable performance in critical applications % flushed with 8 megohm DI water for low extractables Manufactured in a Class, Clean Room environment for high purity hardware offers wide range of chemical compatibility Rigid, molded cage protects pleated media and strengthens structural stability Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics Available in standard lengths and end cap configurations to fit most filter housings Produced up to inches in length ( inch modules) Applications Specifications & Operating Parameters RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Pore Sizes.3,.,.2,.5,.65,.8,. and.2 microns absolute retention Nominal Lengths 9.75" (2.7 cm), " (25. cm), 2" (5.8 cm), 3" (76.2 cm), " (.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter." (2.5 cm) Media Surface Area 7.2 sq.ft. (.67 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Asymmetric Polyethersulfone Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure 75 psid @ 7ºF (5.2 bar @2ºC), psid @76ºF (2.8 bar @ 8ºC) Sanitization and Sterilization Hot water at 75ºF (8ºC) at 5 psid for 3 minutes In-line steam at 257ºF (25ºC) @ psid (.7 bar) for 3 minutes Autoclavable at 257ºF (25ºC) for 3 minutes FDA and USP Compliance All polypropylene materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop Integrity Testing 6.3 µm PORE SIZE AIR DIFFUSION RATE 5 3 2. µm.2 µm.5 µm.65 µm,.8 µm. µm,.2 µm.3 μm. μm.2 μm.5 μm.65 μm.8 μm. μm.2 μm <55cc/min@6psi <55cc/min@8psi <55cc/min@psi <55cc/min@2psi <55cc/min@5psi <55cc/min@2psi <55cc/min@8psi <55cc/min@7psi Per " length water wetted membrane 2 6 8 GALLONS PER MINUTE GPM This chart represents the typical water flow per " cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, P of the housing becomes more apparent. Ordering Guide (Example: MAS.2-SS-G) MAS.2 S S G PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET/O-RING GRADE OPTION MAS.3..2.5.65.8..2 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPDM S = Silicone V = Viton T = Teflon encapsulated Viton (O-ring only) G = General HT = High Temperature* * High Temperature construction (cage, core, end caps): Maximum Temperature 2 F (93.3 C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: MASG.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage MAT Series PTFE Membrane Filter Cartridges Absolute retention ratings from. to. microns High surface area provides superior flow rates and minimizes system size requirements Constructed of Inherently hydrophobic PTFE membrane and polypropylene components Ideal for gas / vent applications and filtering of aggressive solvents and chemicals PTFE membrane and polypropylene component construction offers excellent chemical compatibility and cost effectiveness versus all fluoropolymer filters Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics. Available in standard lengths and end cap configurations to fit most filter housings Applications Tank Ventilation Process Gases Compressed Air Alcohols Bases Specialty Chemicals Photoresists Solvents Acids Esters Specifications & Operating Parameters Pore Sizes.,.2,.5,. microns Nominal Lengths 9.75" (2.7 cm), " (25. cm), 2" (5.8 cm), 3" (76.2 cm), " (.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter." (2.5 cm) Media Surface Area 8.5 sq.ft. (.79 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: PTFE Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure Forward: 7 psid @ 7 F (5.2 bar @ 2 C), psid @76 F (2.8 bar @ 8 C) Reverse: psid @ 7 F (2.7 bar @ 2 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop Air Flow Rate Air Flow Rate. µm System pressure at 3 psig, 65 F (8 C).75.5.25. µm.2 µm.5 µm System pressure at < psig (vent), 65 F (8 C). Outlet open to atmosphere.75.5.25.2 µm.5 µm. µm. µm 2 3 5 2 3 5 SCFM SCFM Water Flow Rate 5 PORE SIZE Integrity Testing AIR DIFFUSION RATE This chart represents the typical water flow per " cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, P of the housing becomes more apparent. 3 2. µm.2 µm.5 µm. µm 3 6 9 2 GPM GALLONS PER MINUTE. μm.2 μm.5 μm. μm <5cc/min@8 psig (.2 bar) <2cc/min@2 psig (.8 bar) <5cc/min@5 psig (.3 bar) <5cc/min@3 psig (.2 bar) Per " length with 6/ IPA/water wetted membrane Ordering Guide (Example: MAT.2-SS-G) MAT.2 S S G PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET/O-RING GRADE OPTION MAT..2.5. 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPDM S = Silicone V = Viton T = Teflon encapsulated Viton (O-ring only) G = General E = Electronic HT = High Temperature* * High Temperature construction (cage, core, end caps): Maximum Temperature 2 F (93.3 C) - Available only in 222 or 226 with Fin or Flat end caps. Note: For vent applications, always use a rupture disc on the tank to prevent against potential collapse. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: MAT.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage WGAS Series Water Grade Polyethersulfone Membrane Filter Cartridges Absolute retention ratings from.3 to. microns 6. square feet (.56 m2) of media surface area per ten inch length for optimal performance Cost effective absolute filtration for less critical applications - not integrity tested % polypropylene construction offers wide range of chemical compatibility Rigid, molded cage protects pleated media and strengthens structural stability Manufactured in state-of-the-art white room environment for high purity Complies with Food & Drug Administration s CFR criteria for food & beverage contact Meets USP Class VI Biological Test for plastics. Available in common end cap configurations to fit most filter housings Produced in standard lengths up to inches Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Specifications & Operating Parameters Pore Sizes.3,.,.2,.5,.65,. microns absolute retention Nominal Lengths 9.75" (2.7 cm), " (25. cm), 2" (5.8 cm), 3" (76.2 cm), " (.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter." (2.5 cm) Media Surface Area 6. sq.ft. (.56 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Asymmetric Polyethersulfone Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure 75 psid @ 7 F (5.2 bar @ 2 C), psid @76 F (2.8 bar @ 8 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop BAR.28.3 µm. µm.2..7 3 2.2 µm.5 µm.65 µm. µm. 2 6 8 GPM 3.79 7.57.36 8.93 37.9 LPM Gallons per Minute This chart represents typical water flow per " cartridge length. The test fluid is water at ambient temperature. Extrapolation for multiple elements tends to be linear, but as flows increase the P of the housing becomes more apparent. Ordering Guide (Example: WGAS.2-SS) WGAS.2 S S PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET / O-RING WGAS.3..2.5.65. 9.75" " 9.75" 2" 29.25" 3" " S = S3 = S = S5 = S6 = S7 = S9 = DOE 222 w/ Fin End 222 w/ Flat End 226 w/ Fin End 226 w/ Flat End Internal O-ring with Recessed Plug Internal O-ring on both ends B = E = S = V = T = Buna N EPR Silicone Viton Teflon encapsulated Viton (O-ring only) Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: WGAS.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.
MicroVantage WGPS Series Water Grade Polysulfone Membrane Filter Cartridges Absolute retention ratings from.3 to. microns 6. square feet (.56 m2) of media surface area per ten inch length for optimal performance Highly tapered asymmetric pore structure provides excellent flow rate and dirt holding capacity Cost effective absolute filtration for less critical applications - not integrity tested Rigid, molded cage protects pleated media and strengthens structural stability Manufactured in state-of-the-art white room for high purity Complies with Food & Drug Administration s CFR criteria for food & beverage contact. Meets USP Class VI Biological Test for plastics Available in common and end cap configurations to fit most filter housings Produced in standard lengths up to inches Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Specifications & Operating Parameters Pore Sizes.3,.5,.,.2,.5,.65,. microns absolute retention Nominal Lengths 9.75 (2.7 cm), (25. cm), 2 (5.8 cm), 3 (76.2 cm), (.6 cm) Outside Diameter 2.67 (6.78 cm) Inside Diameter. (2.5 cm) Media Surface Area 6. sq.ft. (.56 m2) per inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Polysulfone Outer Cage Inner Core: End caps: Maximum Operating Temperature 76 F ( 8 C) Recommended Change-out Differential Pressure 35 psid (2. bar) Maximum Differential (Collapse) Pressure Forward: 75 psid @ 7 F (5.2 bar @ 2 C) Reverse: psid @ 76 F (2.8 bar @ 8 C) Sanitization and Sterilization Hot water at 75 F (8 C) at 5 psid for 3 minutes In-line steam at 257 F (25 C) @ psid (.7 bar) for 3 minutes Autoclavable at 257 F (25 C) for 3 minutes FDA and USP Compliance All materials comply with the requirements of Food and Drug Administration Title 2 of The Code of Federal Regulations 7.5, 77.52 and 77.63. All components meet current USP Class VI biological tests for plastics www.shelco.com
Flow vs. Pressure Drop BAR.28.3 µm.5 µm. µm.2..7 3 2.2 µm.5 µm.65 µm. µm. 2 6 8 GPM 3.79 7.57.36 8.93 37.9 LPM GALLONS PER MINUTE This chart represents typical water flow per cartridge length. The test fluid is water at ambient temperature. Extrapolation for multiple elements tends to be linear, but as flows increase the P of the housing becomes more apparent. Ordering Guide (Example: WGPS.2-SS) WGPS.2 S S PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET / O-RING WGPS.3.5..2.5.65. 9.75" " 9.75" 2" 29.25" 3" " S = DOE S3 = 222 w/ Fin End S = 222 w/ Flat End S5 = 226 w/ Fin End S6 = 226 w/ Flat End S7 = Internal O-ring with Recessed Plug S9 = Internal O-ring on both ends B = Buna N E = EPR S = Silicone V = Viton T = Teflon Encapsulated Viton (O-ring only) Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge housings. Shelco is the perfect choice for your filtration solutions. Shelco Filters Bradley Street Middletown, CT 657 USA Tel: 8-53-583 / Fax: 86-85-62 / E-mail: info@shelco.com MicroSentry, MicroVantage, Shelco Filters and the Shelco logo are registered trademarks of the Tinny Corporation. Shelco Filters is a division of the Tinny Corporation. Bulletin: WGPS.2. Shelco Filters 22 Manufacturer reserves the right to make changes without notice.