TREMLOCK SL INSTALLATION MANUAL

TREMLOCK SL INSTALLATION MANUAL

TREMLOCK SL TremLock SL i a concealed fatener architectural tanding eam roof panel. The TremLock SL panel are eaily intalled over decking, utilizing metal clip. TremLock SL panel are ideally uited for decorative manard, facia and roof. * Other width available upon requet. SUBSTRATE: 24 Gauge Galvalume - Standard Surface PANEL CONFIGURATIONS: Striated, Ribbed or Flat Pan PANEL WIDTH: 16, 18, and (12 Available Upon Requet) PANEL LENGTH: 50 Maximum 3 9 Mimimum PANEL HEIGHT: 1 3/4 MINIMUM SLOPE: 3:12 CLIP SPACING: See U.L. 90 Claification - Roof Deck Contruction for maximum clip pacing. U.L. 90 Claification - Roof Deck Contruction: U.L. Cla 90-24 Ga. minimum panel on 4-0 maximum purlin pacing, per U.L. contruction #255 U.L. Cla 60-24 Ga. minimum panel on 5-0 maximum purlin pacing, per U.L. contruction #255 U.L. Cla 90-24 Ga. minimum panel with clip paced 36 on center over plywood decking, per U.L. contruction #343 U.L. Cla 90-24 Ga. minimum panel with clip paced 48 on center over rigid inulation on metal deck, per U.L. contruction #468 IMPACT RESISTANCE: UL 2218 - IMPACT: CLASS 4 EXTERNAL FIRE: CLASS A AIR AND WATER INFILTRATION: TremLock SL ytem have been teted in accordance with ASTM E1680 and ASTM E1646 procedure. Oil canning (pan wave) of metal panel i inherent in the product and i not caue for panel rejection.

ACCESSORIES Material: 18 Ga. Length: N/A TremLock SL Standard Clip Item #: 36512 Material: 18 Ga. Length: N/A TremLock SL UL-90 Clip Item #: 36515 5 15/16 Bearing Plate Primed Item #: 94599 Galvanized Item #: 203541 Material: 16 Ga. Length: 5 15/16 3 7/8 2 11/32 2 11/32 5/8 #9-15 x 1 Woodgrip W/O Waher - Plain Item #: 36115 Material: N/A Length: 1 1/4-14 x 1 1/4 TEK2 W/O Waher - Plain Item #: 10969 Material: N/A Length: 1 1/4 Pancake Head Woodgrip Item #: 36116 Material: N/A Length: 1 1 #10-16 x 1 TEK2 Pancake Head Self-Driller Item #: 36117 Material: N/A Length: 1

ACCESSORIES Material: N/A Length: 7/8 Material: N/A Length: Varie 1/4-14 x 7/8 LAPTEK ZAC Self Driller (Part # Varie by Color) #14-10 DEKFAST Phillip (Length Varie by Application) Material: 1/8 DIA Stainle Steel Length: 5/16 43D PopRivet (Part # Varie by Color) Material: N/A Length: 45 Roll Tape Sealant 3/32 x 1 x 45 Item #: 95335 Material: N/A Length: N/A White Urethane Sealant Item #: 95320 Material: N/A Length: N/A Butyl Tube Sealant Item #: 95342 Material: N/A Unit of Meaure: 2 oz. Touch-Up Paint Pen (Part # Varie by Color) Material: N/A Length: N/A Hemming Tool Item #: 36120 2

TRIM Length: 10-3 20-3 4 1/4 6 2 1/2 Soffit Bae Trim Length: 5-3 10-3 3 3/4 2 3/4 1 1 3/4 1 3/4 Outide Corner 2 3/4 1 3/4 Inide Corner Length: 5-3 10-3 3 3/4 1 3/4 1 4 3/8 12 * Length: 10-3 20-3 3 1/2 5/8 Eave Trim* *pecify roof pitch 5 1/8 12 * Length: 10-3 20-3 3 1/2 5/8 1 3/4 Eave Drip Trim* *pecify roof pitch Length: 10 1 5/8 Perimeter Cleat 5/8 3

TRIM 5/8 1 3/4 1 3/8 Length: 10 Perimeter Zee Trim 12 * 1 9 1/2 9 1/2 Length: 10-3 20-3 Valley Trim* *pecify roof pitch 3/16 1 3/4 1 1/2 Length: 10 Offet Cleat 5 1/8 5 1/4 5/8 Length: 10-3 20-3 Rake Trim 3 5/8 3 3/8 Length: 10-3 20-3 Rake Tie-In Trim 1 3/8 1 3/4 Length: 10 1 3/8 Zee Cloure 4

TRIM 12 * Length: 10-3 20-3 5 1/4 5/8 6 1/2 Hi-Side Trim* *pecify roof pitch * 12 Hi-Side Tie-In Trim* *pecify roof pitch Length: 10-3 20-3 8 4 1/2 * 12 Hip Flahing* *pecify roof pitch Length: 10-3 20-3 6 3/8 6 3/8 12 * Ridge Flahing* *pecify roof pitch Length: 10-3 20-3 6 3/8 6 3/8 Length: 10-3 20-3 5 5 1 12 1 1/2 3 1/2 * Gutter Trim* *pecify roof pitch 4 Length: 10 1 10 Gutter Strap 5

TRIM 5 5 1 1/2 3 1/2 Length: NA 4 Gutter End Cap 4 14 3 Material: 26 Ga. Length: 14 3 4 3 3 x 4 Downpout 4 3/4 1 3/8 Material: N/A Length: N/A Aluminum Downpout Outlet Box 3 9 Material: 26 Ga. Length: N/A 9 A Style Downpout Elbow 10 Material: 26 Ga. Length: 10 Downpout Strap 6

Note: 7

N O T E S T he detail hown on the following page are uggetion or guideline for intalling the TremLock SL ytem. The intallation detail hown here are proven method of contruction, but they are not intended to cover all building requirement, deign or code. The detail may require change or reviion due to individual project condition. Intallation procedure hall be in accordance with the manufacturer printed intruction, detail or approved hop drawing. Intaller hould thoroughly familiarize themelve with all intruction prior to beginning the intallation proce. The deigner / i ntaller i reponible to enure the following: - That the detail here meet the particular building requirement. - Awarene of and allowance for expanion / c ontraction of the roof panel. - That adequate water tightne i maintained. - That a proper uniform ubtructure i ued to avoid panel ditortion and that the ubtructure meet neceary code requirement. - That all upporting member have been examined and are traight, level, and plumb. Tremco Inc. can provide all flahing and acceorie hown in the intallation drawing unle noted otherwie. Panel, flahing and trim hall be intalled true and in proper alignment with any expoed fatener equally paced for the bet appearance. Sealant hall be field applied on a clean, dry urface. Some field cutting and fitting of panel and flahing i to be expected and to be conidered a part of normal intallation work. Workmanhip hall be of the bet indutry tandard with intallation performed by experienced metal craftmen. Oil canning of metal panel i inherent in the product and i not a caue for rejection. Striated panel are recommended a they reduce the appearance of oil canning. Content of thi manual are ubject to change without notice. To confirm thi book i the mot current copy, pleae viit the Tremco Inc. webite at www.tremcoroofing.com. 8

PANEL HEMMING TOOL Field Notch Field Hem 1 1/2 Panel Hemming Tool Panel Hemming Tool Panel Hemming Tool 1. Cut through male and female leg/rib 1 1/2 up from panel end a hown. 2. Then cut diagonally with metal hear a hown. 3. Place hemming tool over panel tab. 4. Bend down and under to 180 a hown. When the eave drip trim condition i ued, the panel length need to be 3/4 longer than panel ued for offet cleat condition. 9

WALL PANEL BASE (Cut a Required) Ue Clip (Pancake Head ) Fatener to attach Soffit Trim Soffit Soffit Bae Trim Soffit Bae Trim 1. Soffit bae trim hould be intalled with the clip fatener. 10

OUTSIDE CORNER (Field cut a required) 1 3 3/4 Pancake Head Fatener 2-0 O.C. Corner Trim Outide Corner Trim 1. Attach corner trim with fatener on 2-0 center. 2. Field cut panel, a hown, to fit into corner trim. 11

INSIDE CORNER 3 3/4 1 Corner Trim TremLock SL Panel Pancake Head Fatener 2-0 O.C. Subtructural Inide Corner Trim (Field cut a required) 1. Attach corner trim with fatener on 2-0 center. 2. Field cut panel, a hown, to fit into corner trim. 12

EAVE TO WALL TRANSITION 1 Roll Tape Sealant Offet Cleat Pancake Head Fatener 1-0 O.C. (Mut Penetrate Tape Sealant) Fill Cavity w/urethane Sealant at End (Field cut a required) Eave Trim Perimeter Zee Hex Head Fatener #9-15 x 1 Type A Woodgrip (2 per Panel) Pancake Head Fatener Offet Cleat Eave Trim 1 Roll Tape Sealant Perimeter Zee 1. Locate a clip approximately 6 down from tranition and attach panel. 2. Attach perimeter zee a hown. 3. Secure eave trim to perimeter zee. 4. Apply a continuou run of 1 roll tape ealant on eave trim. 5. Locate offet cleat over tape ealant and faten to ubtructure. Pancake head fatener hould penetrate the ealant. 6. Locate a clip approximately 6 up from tranition. 7. Before attaching TremLock SL panel, field cut 1 1/2 off the leg of the panel and hem panel. Allow clearance for thermal movement. 13

Tremlock SL STANDARD EAVE WITH OFFSET CLEAT 1 Roll Tape Sealant Offet Cleat Fill Cavity w/urethane Sealant at End Pancake Head Fatener Eave Trim 3 1/2 Pancake Head Fatener 1-0 O.C. (Mut Penetrate Tape Sealant) Perimeter Cleat Attach with Pancake Head Fatener 1-0 O.C. Eave Trim Offet Cleat 1 Roll Tape Sealant Perimeter Cleat 1. Attach perimeter cleat a hown. 2. Secure eave trim to perimeter cleat. 3. Apply a continuou run of 1 roll tape ealant on eave trim. 4. Locate offet cleat over tape ealant and faten to ubtructure. Pancake head fatener hould penetrate the ealant. 5. Locate a clip approximately 6 up from tranition. 6. Before attaching TremLock SL panel, field cut 1 1/2 off the leg of the panel and hem panel. Allow clearance for thermal movement. 14

EAVE WITH STANDARD GUTTER Attach w/pancake Head Fatener 1 Roll Tape Sealant Offet Cleat Fill Cavity w/urethane Sealant at End Pancake Head Fatener 1-0 O.C. (Mut Penetrate Tape Sealant) Fatener Not by Tremco Inc.) Gutter Strap 2-0 O.C. 43D Pop Rivet (2) Gutter SUGGESTED FOR HIGH SNOW AREAS SNOW GUARDS REQUIRED TO PREVENT DAMAGE CAUSED BY SLIDING SNOW. Gutter Gutter Strap Offet Cleat 1 Roll Tape Sealant 1. Locate gutter and place a continuou run of 1 roll tape ealant in gutter leg. 2. Locate a gutter trap at 2-0 on center. Place tape ealant on trap. 3. Locate offet cleat and faten through cleat, trap, ealant, gutter and into the ubtructure. 4. Intall panel. Allow clearance. Field cut 1 1/2 off leg of panel and hem panel. 5. Field bend gutter trap and attach to gutter with two (2) 43D pop rivet. 15

RAKE - STARTING ON MODULE WITHOUT WALL PANEL 1 3/4 Rake Trim 43D Pop Rivet 1-0 O.C. Zee Cloure w/1 Roll Tape Sealant Top and Bottom TremLock SL Clip 3 1/2 Perimeter Cleat Hex Head Fatener #9-15 x 1 Type A Woodgrip at 1-0 O.C. (Mut Penetrate Sealant) Pancake Head Fatener Pancake Head at 1-0 O.C. Zee Cloure w/1 Roll Tape Sealant Top and Bottom Rake Trim Perimeter Cleat 1. Start a TremLock SL panel on the wood or teel-line a hown. 2. Apply a continuou run of 1 roll tape ealant under zee cloure before fatening. 3. Apply a continuou run of 1 roll tape ealant over zee cloure before fatening rake trim. 4. Faten perimeter cleat per dimenion hown. Follow roof lope, and then attach rake trim. 16

RAKE - TERMINATING OFF MODULE W/O WALL PANELS 43D Pop Rivet at 1-0 O.C. Rake Trim Zee Cloure w/1 Roll Tape Sealant Top and Bottom 1 3/4 3 1/2 Pancake Head Fatener Hex Head Fatener #9-15 x 1 Type A Woodgrip at 1-0 O.C. (Mut Penetrate Sealant) Perimeter Cleat Attach with Pancake Head Fatener at 1-0 O.C. Zee Cloure w/1 Roll Tape Sealant Top and Bottom TremLock SL Panel Rake Trim Perimeter Cleat 1. Field cut TremLock SL panel a required. 2. Apply a continuou run of 1 roll tape ealant under zee cloure before fatening. 3. Attach zee cloure with #9-15 x 1 fatener on 1-0 center. 4. Apply a continuou run of 1 roll tape ealant over zee cloure before fatening rake trim. 5. Faten perimeter cleat a hown. Follow roof lope, and then attach rake trim. 17

RIDGE / HIP Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom Ridge/Hip Trim 5 Max. On Pitch Butyl Tube Sealant 43D Pop Rivet at 0-6 O.C. TremLock SL Panel TremLock SL Clip Hex Head Fatener #9-15 x 1 Type A Woodgrip Pancake Head Fatener (2 Per Panel) Ridge/Hip Trim 1 Roll Tape Sealant Zee Cloure 1 Roll Tape Sealant 1 Roll Tape Sealant 2 Minimum Lap RIDGE TRIM LAP 1. Intall panel with a clip approximately 1-0 downhill on each ide of the ridge or hip. 2. Apply a continuou run of 1 roll tape ealant between the panel leg about 5 maximum down from centerline of ridge. 3. Field cut and attach zee cloure with two (2) #9-15 x 1 fatener through cloure, ealant, panel and into ubtructure. See detail for location dimenion. 4. Apply tube ealant to zee cloure and panel rib. 5. Apply a continuou run of 1 roll tape ealant to top of Z cloure. 6. Attach ridge/hip trim to zee cloure with a 43D pop rivet on 6 center. 7. Lap ridge/hip trim with 1 roll tape ealant and pop rivet a hown. Lap away from the prevailing wind direction. Attach with 43D pop rivet 4 on center maximum. 18

HIGH SIDE EAVE WITHOUT WALL PANEL Butyl Tube Sealant Hi-Side Trim 5 1/4 4 5/8 Max. On Pitch 43D Pop Rivet at 0-6 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom ) Perimeter Cleat Hex Head Fatener #9-15 x 1 Type A Woodgrip (2 Required per Panel) Pancake Head Fatener at 1-0 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom Hi-Side Trim Perimeter Cleat 19 1. Place a continuou run of 1 tape ealant between the panel leg. 2. Field cut and attach zee cloure with two (2) #9-15 x 1 fatener through cloure, ealant, panel and into ubtructure. 3. Apply tube ealant to zee cloure and panel rib. 4. Attach idewall perimeter zee. 5. Slide hi-ide trim over perimeter zee, before attaching to zee cloure. Place a run of 1 tape over zee cloure. 6. Attach hi-ide trim to zee cloure with 43D pop rivet on 0-6 center.

HIGH SIDE EAVE WITH WALL PANEL Hi-Side Trim Butyl Tube Sealant 4 5/8 Max. On Pitch 43D Pop Rivet at 0-6 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom 5 1/4 Perimeter Zee Hex Head Fatener #9-15 x 1 Type A Woodgrip (2 Required per Panel) Hex Head Fatener #9-15 x 1 Type A Woodgrip (2 Required per Panel) Pancake Head Fatener TremLock Sl Panel Perimeter Zee Hi-Side Trim Zee Cloure w/1 Roll Tape Sealant Top and Bottom 1. Place a continuou run of 1 tape ealant between the panel leg. 2. Field cut and attach zee cloure with two (2) #9-15 x 1 fatener through cloure, ealant, panel and into ubtructure. 3. Apply tube ealant to zee cloure and panel rib. 4. Attach idewall perimeter cleat. 5. Slide hi-ide trim over perimeter cleat, before attaching to zee cloure. Place a run of 1 tape over zee cloure. 6. Attach hi-ide trim to zee cloure with 43D pop rivet on 0-6 center. 20

VALLEY 1 Roll Tape Sealant Fill Cavity w/urethane Sealant at End Valley Trim Offet Cleat 4 Typical Pancake Head Fatener at 1-0 O.C. (Mut Penetrate Tape Sealant) Pancake Head Fatener Pancake Head Fatener at 1-0 O.C. (Mut Penetrate Tape Sealant) Valley Trim 1 Roll Tape Sealant Offet Cleat 1. Locate valley trim over ubtructure. 2. Apply a continuou run of 1 roll tape ealant over valley trim and under offet cleat. 3. Locate offet cleat approximately 4 from center of valley trim and faten through cleat, ealant, valley trim and into ubtructure. 4. Locate a clip 6 from end of panel. 5. Field cut 1 1/2 off leg of panel and hem panel. Allow clearance for thermal movement. 21

START RAKE TIE-IN - ENDWALL PARAPET Parapet Wall Sealant (A ) 3 5/8 Min. Counter Flahing (A ) Tie-In Trim 43D Pop Rivet at 1-0 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Top and Bottom Hex Head Fatener #9-15 x 1 Type A Woodgrip at 1-0 O.C. (Mut Penetrate Sealant) Pancake Head Fatener Parapet Wall Counter Flahing (A ) Tie-In Trim Zee Cloure 1. After panel are intalled, cut termination at wall if required. 2. Apply a continuou run of 1 roll tape ealant on panel approximately 1 1/2 in from edge of ubtructure. 3. Locate zee cloure over tape ealant and attach with #9-15 x 1 fatener on 1-0 center. 4. Apply a continuou run of 1 roll tape ealant over zee cloure. 5. Faten tie-in trim to zee cloure with 43D pop rivet on 1-0 center. 6. Counter flahing and ealant a pecified. 22

FINISH RAKE TIE-IN - ENDWALL PARAPET Sealant (A ) Parapet Wall Counter Flahing (A ) Tie-In Trim 43D Pop Rivet at 1-0 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Top and Bottom 3 5/8 Minimum Pancake Head Fatener Hex Head Fatener #9-15 x 1 Type A Woodgrip 1-0 O.C. (Mut Penetrate Sealant) Counter Flahing (A ) Parapet Wall TremLock SL Panel Tie-In Trim Zee Cloure 1. After panel are intalled, cut termination at wall if required. 2. Apply a continuou run of 1 roll tape ealant on panel approximately 1 1/2 in from edge of ubtructure. 3. Locate zee cloure over tape ealant and attach with #9-15 x 1 fatener on 1-0 center. 4. Apply a continuou run of 1 roll tape ealant over zee cloure. 5. Faten tie-in trim to zee cloure with 43D pop rivet on 1 -O center. 6. Counter flahing and ealant a pecified. 23

START RAKE TIE-IN - ENDWALL WITH WALL PANEL Exterior Wall Panel (Optional) 43D Pop Rivet at 1-0 O.C. Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom Fatener 1-0 O.C. (Not by Tremco Inc.) Tie-In Trim Pancake Head Fatener Hex Head Fatener #9-15 x 1 Type A Woodgrip 1-0 O.C. (Mut Penetrate Tape Sealant) Exterior Wall Panel (Optional) Tie-In Trim TremLock SL Panel Zee Cloure w/1 Roll Tape Sealant (Top and Bottom) 1. After panel are intalled, cut termination at wall if required. 2. Apply a continuou run of 1 roll tape ealant on panel approximately 1 1/2 in from edge of ubtructure. 3. Locate zee cloure over tape ealant and attach with #9-15 x 1 fatener on 1-0 center. 4. Apply a continuou run of 1 roll tape ealant over zee cloure. 5. Faten tie-in trim to zee cloure with 43D pop rivet on 1-0 center. Fatener for trim to ubtructure i not by Tremco Inc. 24

HIGH SIDE TIE-IN - SIDEWALL PARAPET ABOVE ROOFLINE Sealant (A ) Counter Flahing (A ) Parapet Wall Fatener (A ) 43D Pop Rivet at 0-6 O.C. Tie-In Trim Zee Cloure (Field Cut) w/1 Roll Tape Sealant Top and Bottom 6 Max. Butyl Tube Sealant Pancake Head Fatener Hex Head Fatener #9-15 x 1 Type A Woodgrip 2 Required per Panel (Mut Penetrate Tape Sealant) Counter Flahing (A ) Tie-In Trim Sealant (A ) Parapet Wall Zee Cloure w/1 Roll Tape Sealant (Top and Bottom) 1. After panel are intalled, place a continuou run of 1 roll tape ealant approximately 6 from edge of wall ubtructure. 2. Field cut zee cloure and intall over tape ealant and attach with two (2) #9-15 x 1 fatener through cloure, ealant, panel and into ubtructure. Locate a hown. 3. Apply tube ealant to zee cloure and panel rib. 4. Apply a continuou run of 1 roll tape ealant over zee cloure and faten trim to cloure with 43D pop rivet on 6 center. Ue tube ealant at cloure. 5. Fatener for attachment to parapet wall i not by Tremco Inc. 6. Counter flahing and ealant to parapet wall a pecified. 25

HIGH SIDE TIE-IN - SIDEWALL WITH WALL PANELS 6 Max. Fatener (A ) Tie-In Trim 43D Pop Rivet at 0-6 O.C. Zee Cloure (Field Cut) 1 Roll Tape Sealant (Not by Tremco Inc.) Butyl Tube Sealant Pancake Head Fatener Hex Head Fatener #9-15 x 1 Type A Woodgrip 2 Required per Panel (Mut Penetrate Tape Sealant) Exterior Wall Panel (Optional) Tie-In Trim Zee Cloure 1 Roll Tape Sealant (Top and Bottom) TremLock SL Panel 1. After panel are intalled, place a continuou run of 1 roll tape ealant approximately 6 from edge of wall ubtructure. 2. Field cut zee cloure and intall over tape ealant and attach with two (2) #9-15 x 1 fatener through cloure, ealant, panel and into ubtructure. Locate a hown. 3. Apply tube ealant to zee cloure and panel rib. 4. Apply a continuou run of 1 roll tape ealant over zee cloure and faten trim to cloure with 43D pop rivet on 6 center. Ue tube ealant at cloure. 5. Fatener for attachment to wall ubtructure are not by Tremco Inc. 26

ROOF JACK INSTALLATION Dektite Tube Sealant Field cut hole a per note #2 1. Before cutting hole in heet, conider the bet poition to uit ize of Dektite elected. 2. Cut a neat hole with minimum clearance for pipe and intall pipe. 3. Rubber leeve hould be a watertight fit on pipe. If rubber ha to be cut, a neat hole 1/2 dia. le than outide pipe diameter hould be cut in Dektite. Ue a harp pair of cior and avoid nick. 4. Apply tube ealant to underide of bae and, uing water a lubricant, lide flahing along until it meet heet. 5. Hand pre Dektite bae on to heet, preing bae firmly to heet to avoid gap, progreively drill and faten to heet. Faten to panel with 1/4-14 x 7/8 LAPTEK ZAC Fatener. 27

Tremco Incorporated 3735 Green Road Beachwood, Ohio 44122 216-292-5000 Rev 3/11