CPC EVACUATED TUBE COLLECTOR SYSTEMS FOR PROCESS HEAT UP TO 6 C Rolf Meissner Ritter XL Solar GmbH e-mail: r.meissner@ritter-xl-solar.com Introduction Using water as heat transfer fluid CPC evacuated tube collector (CPC-ETC) technology generates temperatures of 8 6 C under almost all weather conditions all year round.. CPC-ETC with water as heat fluid is completely self-secured against thermal standstill, even in the event of a power cut. Therefore, with this technology storage tanks can be optimized according to space considerations, load profiles and profitability; in the case of low collector areas storage tanks can often be done away with completely. This means that CPC-ETC technology is ideally suited for middle-temperature process heat, district heating, and providing high levels of solar heat support to heating systems.. Outline of CPC-ETC with AquaSystem The foundations of this technology are Dewar, or Sydney, tubes. These are double-walled glass vessels, constructed in an analogously simple manner to a thermos flask. Due to the experimentation performed on thermos flasks for over a hundred years, Dewar collector tubes have a lifetime of to 5 years. On the surface of the inner tube a highly selective absorber is coated in good solar radiation conditions and under thermal standstill, this absorber is heated to temperatures of up to 35 C. If the collector i s not in thermal standstill, the heat is transferred via a thin water-carrying metal tube, which is made of copper, steel, or stainless steel depending on its use. The CPC mirror (Compound Parabolic Concentrator) guarantees that as few tubes as possible are needed per unit area and yet over 9 percent of the gross collector area is still optically used. This saves material, increases the yield and decreases the heat loss. Due to the special geometry of this set-up all light (both direct and diffuse) is used. Illustration : Dewar pipes, CPC mirror, metal heat conductor and tube Illustration : Ray paths for direct and diffuse solar radiation
Illustration 3: Collector efficiency curves for plasma coated CPC-ETC collectors and the dependence of the radiation incident angle on the fraction of used radiation for CPC-ETC and for flat collectors The plots of collector performance show that, for a temperature difference between the collector and the surroundings of 5 Kelvin, the collector has an efficiency of over 5 for watt/m² of irradiation. Even with only 4 watt/m² of irradiation the efficiency is well over 5. In order to reach efficiencies of at least 5 for temperature differences of less than 75 Kelvin, irradiation of only 5 watt/m² will suffice such levels can be achieved without sunshine. Therefore, if an operational pressure of 6 bars is used, water can easily be heated to 6 C using CPC-ETC without mechanical tracking and can then be used for process heat. In addition, physical investigations have shown that the production of steam presents no problem. A particular advantage of cylindrical absorbers is the fact that the incident radiation which the collector can use is nearly independent of the radial angle of incidence. In practical terms, this means that throughout the day almost exactly the same maximum performance can be expected over many hours. In contrast to more highly-concentrating technologies, such as parabolic or Fresnel mirror collectors, CPC-ETC makes use of almost all diffuse light, which corresponds to around half of the solar radiation worldwide. Only in a few extreme areas does the diffuse light sink to a quarter of the total irradiation. Using the Solar Keymark Output Calculator (SKOC), the following collector yields have been calculated for locations in Stockholm, Vienna, Davos, Athens und Hurghada, for constant medium collector temperatures of 6 C, 9 C, C, 5 C und 8 C. These are almost equal to the process temperatures in case of small solar temperature differences. SKOC is only calibrated up to C and was further dev eloped to give the results here. However, how do the simulation results for high temperatures compare to results obtained by testing collectors according to EN (European Norm) 975-. As the measured stagnation temperatures correspond well with the calculated ones, it can be assumed that the calculated results are also reliable for those temperatures which were not measured. Illustration 4 annual collector yield per square meter of collector area (left) and as a percentage of the irradiation (right), for a south-facing orientation and a 3 degree inclination.
. CPC-ETC with AquaSystem in comparison It is not widely appreciated that CPC evacuated tube collectors (CPC-ETC), which do not concentrate sunlight, give a greater yield than solar collector technology which does concentrate sunlight. This is partly due to the fact that, until now, few references have been made to ETC, and partly because ETC was not developed with the target of application to super-heated water, steam or heat transfer oil. Hot water and heating are the focus of ETC development; even under unfavourable weather and climate conditions, temperatures of 95 C should almost alw ays be generated. In contrast, concentrating solar technology with parabolic or Fresnel mirrors was developed exclusively for high temperature applications such as solar cooling or electricity generation. For such a technology it is unavoidable that diffuse sunlight remains almost completely unused. These concentrating collectors do have important advantages when used at temperatures above C. However, such high-temperature applications are much less common than those that require temperatures between and C, which is why attempts are being made to establish the technology at lower temperatures. For CPC-ETC, applications with temperatures far higher than C present th emselves, since it is accepted that CPC-ETC collectors are very efficient in this temperature range compared to concentrating collectors and are not dependent on whether the sunlight is direct or diffuse. The curves below are based only on the collectors and their gross collector area, not on the whole system. 8 Collector power [ Watt/m² gross coll. area ] 7 6 5 4 3 irradiance 8 W/m² 6 W/m² 4 W/m² W/m² 5 5 Temperature difference [Kelvin] CPC-evacuated tube collectors w ith plasma coating, Ritter CPC-evacuated tube collectors, Ritter standard since 999 CSP Concentrating Solar Power, Fresnel reflectors at 8 W/m² direct irradiance CSP Parabolic Trough Collector (Sopogy, USA) at 8 W/m ² direct irradiance CSP don't use diffuse irradiance (that is 5...75 % of all irradiation). Illustration 5 Efficiency curves of CPC-ETC, Fresnel reflector and parabolic trough collectors For Fresnel and parabolic trough collectors all irradiance has to be direct! For the CPC-ETC and the parabolic trough collector, Solar-Keymark and SRCC certification data were used. For the Fresnel collector the curve was taken from publications by TVP (emerged from CERN) with an aperture/gross collector area ratio of 8 %. Even though the CSP curve has an uncertainty of, the maximum yield relationships are clear. It also has to be considered that CSP collectors need to be constantly and precisely repositioned on at least one axle by an electromechanical apparatus, while CPC-ETC collectors, once optimally installed according to latitude and usage, remain permanently mounted in one position. It is also important to clarify certain points about solar radiation:. In almost all locations worldwide the percentage of diffuse sunlight is well over 5 %. This percentage only sinks to around 5 % in extremely arid and inhospitable areas. All this diffuse radiation is not used by concentrating technology. In addition, if the mirrors become even slightly dirty the yield will rapidly approach zero, as direct radiation is then converted into diffuse radiation.. The direct radiation spectrum very rarely reaches its peak values. Without the additional diffuse radiation it is virtually impossible to obtain power above 9 W/m². The yearly average for total radiation does not exceed 6 W/m² anywhere on the planet, and the yearly average for direct radiation scarcely reaches 5 W/m². In these values we have neglected all radiation below W/m², as otherwise the yearly average would clearly fall even lower.
Irradiance [W/m²] onto the horizontal area (< W/m² neglected) 35 Radiation time in hours 3 5 5 5 > > > 3 > 4 > 5 > 6 > 7 > 8 > 9 > > total radiation : direct radiaton (diffuse light is neglected) : yearly rad. average yearly rad. sum dayly rad. max 368 W/m² 93 kwh/m ² 8,57kWh/m ² 3 W/m² 46 kwh/m ² 7,4kWh/m ² Hurghada, Egypt Irradiance [W/m²] onto the horizontal area (< W/m² neglected) 45 Radiation time in hours 4 35 3 5 5 5 > > > 3 > 4 > 5 > 6 > 7 > 8 > 9 > > total radiation : direct radiaton (diffuse light is neglected) : yearly rad. average yearly rad. sum dayly rad. max 6 W/m ² 335 kwh/m² 9,8kWh/m ² 53 W/m ² 793 kwh/m² 7,9kWh/m ² Illustration 6 METEONORM 4. data about total and direct irradiance in Wurzburg und Hurghada Radiation relationships and collector curves give only snapshots. A year-long simulation for particular locations with defined temperature conditions is much more informative. The following simulation was calculated using T*SOL 5. Professional to compare the performance of a particularly simple hydraulic system at 5 different locations for 5 different collector types and 3 operating temperature conditions. Only the collectors were considered. The heat loss of the piping has almost been neglected and considered to be constant. Unfortunately, some corrections and comparisons with other results (obtained using different methods) had to be made in the case of the concentrating collectors in order to quantify the effect of the mechanical power required. This accounts for the uncertainty of %.,5 Yearly energy yield (75 / 88 C) e. g. stage solar cooling,5 Yearly energy yield (5 / 3 C) e. g. solar cooling, process heat,5 Yearly energy yield ( / 6 C) e. g. solar cooling, process heat Illustration 7 One year T*SOL simulations for different temperatures, sites and collector systems.3 Applications for solar process heating, cooling and domestic heating networks About 5 CPC ETC systems have been installed so far with water pressurized up to 8 bars and operation temperatures of 7 95 C, 35 of them for process heat, solar cooling or district heating and of them with more than m² collector area. Only one CPC ETC, which does not work with water but with silicon oil and supports a Stirling engine, has been built for temperatures of 6 8 C. Wa ter
steam generation is already proved at testing systems. At the moment a 4 m² installation is under construction for a water steam jet cooling pump with steam temperatures of 6 8 C. 33 m² Festo ( 7) cooling and heating 33 m² Metro Istanbul (Turkey 9) cooling 3388 m² trade center Wels (Austria ) domestic heating network 458 m² Juluis Blum (Austria ) galvanization m² Hustert Galvanic ( ) galvanization 394 m² Zehnder (Schweiz ) galvanization 64 m² New York tube (USA ) train washing 57 m² Elk (Poland 9) concrete plant 47 m² Parris Island (USA ) cooling 55 m² Kral (Austria ) cooling Illustration 8 CPC ETC applications for domestic heating networks, cooling and process heat Summary CPC ETC water technology is a high-efficient solar thermal system and already proven at lower temperatures millions of times. Obviously it is also reliable for medium-sized temperatures up to 8 C. With water as heat fluid there is a temporary restriction to 6 C because the boiling pressure must not be higher than bars. The hydraulic system has also already proven thousands of times at temperatures up to 95 C to be proofe against therm al stagnation by self-filling and self-emptying in the case of boiling although the collectors are not tracked. For higher temperatures different pumps, valves, storages and thermal insulations are necessary. The R&D as well as the testing efforts are comparably small because the collector system already exists. Depending on the geographic location for operation temperatures of 6 C a solar efficiency of about...4 % is possible. The time is ripe for using CPC ETC in industrial processes for heating and cooling.