PVC Stub Flanges & Backing Rings Australian Made for the pressure pipe market Quick Alignment No Pre-drilling of Holes Easier Installation Australian Made Manufactured to Class 18 Quality ISO 9001 Lic 570
Quality ISO 9001 Lic 570 TABLE OF CONTENTS INTRODUCTION Design BENEFITS Basis APPLICATIONS DESIGN 3 ASSEMBLY PE100 5mm to 100mm PN6.3 PN10 35 ALIGNMENT 4 PRESSURE TESTING 4 PRODUCT DATA 4 REFERENCES PE100 5mm to 100mm 48 Limitation of Liability This manual has been compiled by Vinidex Pty Limited ( the Company ) to promote better understanding of the technical aspects of the Company s products to assist users in obtaining from them the best possible performance. The manual is supplied subject to acknowledgment of the following conditions: The manual is protected by copyright and may not be copied or reproduced in any form or by any means in whole or in part without prior consent in writing by the Company. Product specifications, usage data and advisory information may change from time to time with advances in research and field experience. The Company reserves the right to make such changes at any time without further notice. Correct usage of the Company s products involves engineering judgements which can not be properly made without full knowledge of all the conditions pertaining to each specific installation. The Company expressly disclaims all and any liability to any person whether supplied with this publication or not in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance whether whole or partial upon the whole or any part of the contents of this publication. No offer to trade, nor any conditions of trading, are expressed or implied by the issue of content of this manual. Nothing herein shall override the Company s Condition of Sale, which may be obtained from the Registered Office or any Sales Office of the Company. This manual is and shall remain the property of the Company, and shall be surrendered on demand to the Company. Information supplied in this manual does not override a job specification, where such conflict arises, consult the authority supervising the job. Copyright Vinidex Pty Limited
PVC Stub Flanges & Backing Ring Introduction Replacing our traditional Cat.16 full face flange, Vinidex are pleased to offer their injection moulded PVC Stub Flange incorporating the Vinidex PVC Backing Ring. Flanged joints in pipelines are used to create a demountable joint for future disassembly to connect valves and vessels, where strength in tensions is required or to join to other materials. The Vinidex Stub Flanges and PVC Backing Rings enable easy access to joins for future maintenance. This unique, lightweight and corrosion resistant system, offers faster and easier connections as the Vinidex PVC Backing Rings are supplied with moulded bolt holes compatible with both Table D and Table E in accordance with AS 19. Benefits Easier installation Quick alignment No pre-drilling of holes Light weight compared to metal backing rings Australian Made - Vinidex own manufacture Greater installation efficiency Corrosion resistance Made to Australian Standards Manufactured to Class 18 Coloured to match existing systems Vinidex quality & reputation Applications The PVC Stub Flange and Backing Ring fitting from Vinidex can be used on PVC pipes for plumbing, irrigation, industrial and rural applications.
PVC Stub Flanges & Backing Ring 4. Check that the nuts and bolts easily screw together and have sufficient thread to enable the sealing surfaces to meet and to be tensioned. 5. Place Backing Ring on the pipe in readiness for jointing, ensuring the ribbed side of the Backing Ring is facing the Stub Flange. Design The Vinidex PVC Stub Flanges and Backing Rings are designed in accordance with Australian Standards, and as such the relevant sections of the Vinidex Water Supply Technical Manual for PVC Pressure Pipe Systems apply. To ensure a long service life, the Vinidex PVC Stub Flanges and Backing Rings should be installed in accordance with AS/NZS566.1:1998. Installation This section should be read in conjunction with Australian Standards AS03 - Installation of UPVC Systems. Installers should also be familiar with the Vinidex Water Supply Manual for PVC Pressure Pipe Systems, Technical Manual. Assembly Preparation prior to assembly will be a key function to a successful installation. Prior to installation a number of checks need to be carried out: 1. Ensure the sealing faces of both the Stub Flange and the mating surface are flat, clean and with no evidence of burrs or notches. 6. Having cut the pipe to the correct length, prepare the pipe end and the socket of the Stub Flange for solvent cementing to each other. The preparation and the solvent cement joint are to be executed in accordance with AS03. With the Flange Plate held captive on the pipe, the following steps are mandatory. 1. Washers to be placed under the heads of all bolts and nuts to spread the force and prevent damage to the Backing Ring.. Tighten bolts gradually by pulling down the nuts diametrically opposite each other using a torque wrench to ensure even loading around the bolt heads and nuts, Figure 1. 3. Tighten each bolt several times repeating the process pattern. 4. The final recommended torque value for Stub Flange bolts are shown in Table. Figure 1. 3. When jointing flange to ring, check the size and number of the nuts and bolts are in accordance with AS19, Table D or Table E. 3. When determining the bolt length consideration should be given to the thickness of the PVC Backing Ring. Thicknesses of PVC Backing Rings are shown in Table below. Nominal Size Torque Table. Thickness DN Value 50 4mm 50Nm 80 38mm 50Nm 100 31mm 50Nm 150 46mm 65Nm
PVC Stub Flanges & Backing Ring Alignment Alignment of the Stub Flange to the mating flange should be installed with the normal installation tolerance in accordance with Australian Standards AS03. The Stub Flange joint should be completed and allowed to cure prior to torquing the flange bolts. Premature torquing of the bolts will cause movement of the joint and weaken the joint itself. Pressure Testing Upon completion, the system should be pressure tested in accordance with Australian Standard AS03. As the Stub Flange is solvent cemented to the pipe the system should not be pressure tested until at least 4 hours after the last joint has been made. Product Data Vinidex Code Description Carton QTY Bag QTY 50mm PVC Stub Flange & Backing Ring 35651 0 10 0.397 80mm PVC Stub Flange & Bakcing Ring 35671 10-0.660 100mm PVC Stub Flange & Backing Ring 35681 7-1.037 150mm PVC Stub Flange & Bakcing Ring 35701 7 -.138 The Vinidex PVC Backing Rings are supplied with moulded bolt holes that are compatible with Table D and Table E in accordance with AS19. W (kg) References Australian Standards AS03: 1977 - Installation of UPVC Pipe Systems. 4
CORPORATE HEAD OFFICE Vinidex Pty Limited ABN 4 000 664 94 19 1 Loyalty Road PO Box 4990 North Rocks NSW 151 Tel: +61 8839 9006 Fax: +61 8839 915 CUSTOMER SERVICE Sales Hotline: 13 11 69 Sales Fax: 13 4 43 Email: info@vinidex.com.au Web: www.vinidex.com.au