Destination Indoor and outdoor decoration of buildings evn of those with particular historicartistic importance. Even if it reaches a high thickness layer, it has a high breathability Characteristics Readytouse Antibacterial Adherence to mineral supports BREATHABLE Good light resistance VOC (Directive 2004/42/CE) ( g/l ) 200 <Decorative effects paintings.eu limit value for this product (Cat. A/l): 220g/l (2010). This product cointans max. 200 g/l Recommended surface and temperature conditions Avoid applications at room temperatures lower than +10 C or higher than +3 C and relative humidity higher than 80%. Check the surfaces suitability referred to the humidity degree with hygrometer. Support temperature: min +10 C, max +3 C. Avoid application on chalking surfaces if not peviously treated with fixatives model FIXODIL for outdoors or Acrilan 3470 for indoors. WARNING:ventilate the room to avoid humidity accumulation. WARNING:the maximal washability is obtainable after 710 days from application. Completely eliminate preexistent solvent paintings. Remove, wet sanding or brushing, the possible efflorescences. In presence of moulds, use antimolds detergents and fixing elements. Reccomendations Well mix the product before use The applications must not be executed on walls directly exposed to the sun or with room temperatures under + C. In case of doubt, with old chalking or just a little cohesive paintings, evaluate the first coat dillution. Apply the fixative primer on a little surface portion and after at least 12 hours make an adhesion test. It is recommended to apply the product in favorable weather conditions, as inadequate weather conditions could negatively affect the drying conditions by compromising the optimal achieving of the product aesthetic characteristics and performances. Page 1/
Application cycle Never painted interior walls In case of new civil plasters let it age for at least 28 days (T= 20 C and UR< at7%) ) before any operatin. Carefully brush. Remove bad anchored parts, dust and dirt. level imperfections with STUCOL. After 8 hours level the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry. Verify surface idoneity according to humidity degree with match test or hygrometer. If necessary, consolidation with water fixative as ACRILAN 3470. In case of chalking supports use solvent fixative as FIXODIL, otherwise use the following modalities. If the support does not need fixative, it is anyway recommended to moisten it, to avoid the wall to subtract excessively water from the binder. After 24 hours from fixative application apply a first layer of GRASSELLO DI CALCE. After at least 12 hours apply one more layer to create the adequate thickness. After at least 12 hours sand to remove possible imperfections, then remove dust and apply little quantities of material compacting and polishing it (with inox trowel) beofre it dries completely. Clean the tools withh water after use. Already painted interior walls with tempera paintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Insulate the whole surface with solvent fixative as FIXODIL. After 24 hours apply a first layer of GRASSELLO DI CALCE or marmorino. After at least 12 hours apply one more product layer to cerate the adequate thickness. After at least 12 hours sand to remove possible imperfections, then remove the dust and apply little quantities of material, compacting and polishing it (with inox trowel) before it dries completely. Clean the tolls withh water after use. Page 2/
Application cycle Already painted interior walls with washable hydropaintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect teh surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly drt. Verify surface idoneity according to humidity degree with match test or higrometer. In case of much chalking supports use solvent fixative as FIXODIL. After 24 hours apply a first layer of GRASSELLO DI CALCE or marmorino. After at least 12 hours apply one more layer to give the adequate thickness. After at least 12 hours wet sanding to remove possible imperfections, then remove the dust and apply little quantities of material, compacting it and polishing it (with inox trowel) before it completely dries. Clean the tools with water after use. Never painted exterior walls In case of new civil plasters let age for at least 28 days( T= 20 C and U.R. < at 7%) before any operation. Carefully brush. Remove badanchored parts, dust and dirt. Level imperfections with special plasters. Wait the drying times and sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry.. Verify surfaces idoneity according to humidity degree with match test or higrometer. If necessary, use water fixative for solidification as ACRILAN 3470. If the support does not need fixative, it is recommended to moisten it, to avoid that the wall subtracts excessively the watre in the binder. Apply a first coat of product diluted at 3 40%. After at least 4 6 hours apply a second layer of prodct diluted at 30 3%. Already painted exterior walls Completely remove the old organic paintings as synthetic ones, washable quartz, tempera and plastic coatings. Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 h sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry. Verify surfaces idoneity according to humidity degree with match test or higrometer. If necessary, use water fixative for solidification as ACRILAN 3470. If the support does not need fixative, it is recommended to moisten it, to avoid that the wall subtracts excessively the watre in the binder. Apply a first coat of product diluted at 3 40%. After at least 4 6 hours apply a second layer of prodct diluted at 30 3%. Page 3/
Characteristics and technical informations Tin aspect RESIN Color Use Data observable at T=20 C and 60% relative humidity Tixotropic White White suitable for tintometric system MW2 Adherence to mineral supports Spatula Thinner Tools' cleaning Application process Water Water Brush Thinner (% Volume) TECHNICAL DATA Complete polymerisation days Recoating interval ( h ) Minimum film temperature ( C ) 7 10 12 Notice Mass density ( kg/l ) Solids content by vol. ( % ) Brooklfield viscosity (cp) Brilliance ( % ) Touch dry ( h ) Depth dry ( days ) recommended dry film thickness (dtf) ( µm ) Theoretical spreading rate ( mq²/lt ) Data refer to the product mixed at 20 C. 1,60 6 8 1 (kg/m²) Glossy Page 4/
STORAGE (dry and cool place) 12 months in tightly closed package, protected from frost and heat sources Storage temperature ( C) + +30 Unit size 23 kg Safety instructions Products must be treated with attention, avoid the skin contact. Users will have to follow the actual laws. Actions as wet sanding, sanding, removal with flame, etc. of old painting coats can geerate dust and dangerous smokes. Work in well areated areas and wear the adequate individual protection means. In Italy Decree 303 and 47 concern the rules valid for the application operations. For further information concerning the right product elimination, storage and manipulation please consult the relative taìechnical data sheet. Data in this technical sheet are only given for information and are the result of laboratory tets and practical experience, However, the factory is not responsible if the product isn't used under its direct control. SESTRIERE VERNICI Srl Technical Assistance is available to give all information necessary for a correct use of the product. Be careful: the product could show, towards some subject who are particularly sensitive to isothiazolones, a little irritation. It's thus recommended to use gloves and protective glasses and to wash very well the parts which could by chance touch the skin. Page /