Part Numbers Kinetico Drinking Water Systems Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 1
Model 7000/7500 Components 4 7A 1 8 7B 2 5A 3 5B 6A 6B Dwg. No. Description Part No. 1 Screws (3 required) 1010 2 Ball Valve, Inlet 15792 3 MAC Head 12870A 4 Bracket 9328 5A Elbow, Male ¼ Tube x ⅜ Stem, V/L 15791 5B Elbow, Male ¼ Tube x ⅜ Stem, GAC 15793 6A Cartridge, MAC, V/L 9308A 6B Cartridge, MAC, GAC 9306B 7A Drinking Water Filter, Model 7000 with install kit 4049A 7B Drinking Water Filter, Model 7500 with install kit 4050A 8 K5 Flow Supressor* 13477 *For the use in Mac 7500 only Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 2
Model 7000/7500 Components 2A 1 2B 3 7A 7B 5 6 8 4 Dwg. No. Description Part No. 1 Mounting Screws (2 required) 3321A 2A Elbow, Male, ¼ Tube x ¼ NPT, V/L 15791 2B Elbow, Male, ¼ Tube x ¼ NPT, GAC 15793 3 Union Connector, ¼ T x ¼ T 9847A 4 Tubing, ¼ x 10 8554A 5 Ball Valve 9460 6 Tee, ⅜ x ¼ 9207A 7A Assembly Kit, V/L 14938A 7B Assembly Kit, GAC 14937A 8 Faucet, non-air gap 11450B 9 K5 Flow Supressor* 13477 *For the use in Mac 7500 only Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 3
Plus Deluxe Module Assembly Complete 5 8 6 7 1 2 3 4 Dwg. No. Description Part No. 1 Sump with Plug, RO - Siliconed 12971 2 Module Subassembly (does not include tubing collets) 10504 3 Membrane Assembly 10501 4 Module Assembly 10500 5 O-ring (Top) 9063 6 O-ring (Middle) 5021 7 O-ring (Bottom) 5020 8 O-ring (Membrane) 2648 Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 4
Plus Deluxe Bracket Assembly Dwg. No. Description Part No. 1 Cartridge, Prefilter - Sediment 9309A 1 Cartridge, Prefilter - Carbon/Sediment, High Capacity 9461A 2 Prefilter Head 9313C 3 Elbow, Male ¼" Tube x ¼" NPT 8551 4 Bracket 9326 5 Manifold Clip 9301A 6 Module Assembly - TF 10500 7 Cap Screws 1010 8 MAC Postfilter Head 9382 9 Elbow, Male ⅜ Tube x ¼ NPT (GX) 8552 9 Elbow, ⅜ Tube x ¼ NPT with Flow Control (VX) 9373 10 Cartridge, MAC Postfilter - VOC (VX) 9307A 10 Cartridge, MAC Postfilter - GAC (GX) 9306B 11 Manifold Assembly 9335A 12 Bracket Cover - VX 9358A 12 Bracket Cover - GX 9359A Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 5
AquaKinetic A200 Bracket Assembly 10 4B 8 4 7 11 6 3 2 9 1 5 Drawing No. Description Part No. 1 Cartridge, Prefilter - Sediment 9309A 1 Cartridge, Prefilter, Carbon/Sediment, High Capacity 9461A 2 Prefilter Head 9313C 3 Inlet Elbow, Male ¼ Tube x ¼ NPT 8551A 4A Bracket 9441 4B Bracket Assembly 9442 5 Cartridge, Membrane 9428A 6 Cap screws 1010 7 Postfilter head 9426C 8 Elbow, Male ⅜ Tube x ¼ NPT 8552A 9 Cartridge, MAC GAC Postfilter 9306B 10 Bracket Cover 9443B 11 Module Head Assembly 9440 Not Shown Flow Restrictor, Capillary, A200 10803A Not Shown Drain Elbow 8551A Not Shown Economy Faucet, non air gap 11450B Not Shown Economy Faucet, air gap 11451B Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 6
Plus and A200 Faucets Part No. 12939 Description Non-Air Gap Taps: Plus Deluxe and Purefecta Part No. A200 Part No. Tap Escutcheon Tap, Decorative, Classic Chrome 12725 NA 11621 Tap, Decorative, Satin Nickel 12770 NA 11623 Tap, Decorative, Arctic White 12765 NA 11627 Tap, Decorative, Light Biscuit 12768 NA 11626 Tap, Decorative, Black Licorice 12766 NA 11628 Tap, Decorative, Oil Rubbed Bronze 14683 NA 14684 Tap, Decorative, Polished Brass 12769 NA 11625 Tap, Decorative, Brilliant Nickel 12767 NA 11622 Tap, Decorative, Brushed Stainless 13289 NA NA Tap, Economy Chrome NA 11450B NA Air Gap Taps: Tap, Economy Chrome NA 11451B NA Kit, Air Gap Decorator Tap 12961A NA NA Tap Handle, A200 Only NA 9380 NA Connector, ¼ x ⅜, A200 Only NA 8561A NA Cartridge, Decorator Faucet 12072 NA NA Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 7
3 Gallon QuickFlo Plus Deluxe and A200 Units Part No. Description Color Code 9309A Cartridge, Sediment Prefilter (Plus Deluxe and A200 Models) Yellow Decal 9307A Cartridge, MAC Postfilter Plus Deluxe VX (Replacement only), Plus Deluxe Models ONLY Blue Decal 9306B Cartridge, MAC Postfilter Plus Deluxe GX (Plus and A200 Models) Orange Decal 9461A High Capacity Carbon/Sediment (Plus Deluxe and A200 Models) Purple Decal 9305A Insert Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 8
Storage Tanks 5 1 8 3 2 6 4 9 7 Drawing No. Description Plus and A200 Models 1 Ball Valve, ⅜", Storage Tank 11378 2 Adapter, Stem Tube 9396 3 Bushing, Red ¾ x ⅜" NPT 7542 4 Coupling, ¾ x PVC-thd. 7969 5 Ball Valve Kit 9395 6 Storage Tank, 10 Gallon 12968 7 Storage Tank Assembly, 10 Gallon - RO 9375 8 Ball Valve, ¼ FNPT x ⅜T 12583A 9 Storage Tank, 3 Gallon, Black 9344B Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 9
3 Gallon QuickFlo 1 4 5 6 2 3 Drawing No. Description Part No. 1 Control Valve Assembly 10248C 2 Foot Storage Tank 9487 3 Retainer Storage Tank (not shown) 7964 4 Bladder 9408A 5 Tank Complete 3 gallon 9496 6 Tank only 3 gallon QuickFlo 11716 Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 10
Reverse Osmosis Accessories Booster Pump This Kinetico accessory is designed to produce a higher volume and better quality of water than is possible under low pressure operating conditions. A booster pump is recommended whenever high TDS or low pressure conditions exist. If the volume of water produced by the Kinetico Drinking Water System with the available water pressure is not satisfactory to the customer, a booster pump can be added. The booster pump raises the feed pressure entering the R.O. module to approximately 95 psig. The increased pressure increases the volume and the quality of permeate water produced by the RO module. The Kinetico RO Booster Pump consists of an electric diaphragm pump, voltage transformer and a pressure switch, which turns the pump on via a signal from the Kinetico Drinking Water System. All these components are packaged in an attractive enclosure with a removable cover. The booster pump measures 12" long by 7" wide by 5" high, making it easy to install beneath a kitchen sink or any desirable location. The pump comes with a 5 foot electrical cord. Operation When the Kinetico Drinking Water System senses the tank needs to be filled, the main spool valve in the R.O. module (or the shutoff valve on A200 units) opens. Feed water enters the inlet port, pressurizing the membrane and the bottom of the module. The booster pump pressure switch is connected to a port in the bottom of the RO module via an elbow and ¼" O.D. tubing included in the optional installation kit. The pressure switch contacts close when the water pressure reaches approximately 10 psig. This starts the booster pump, which produces regulated 95 psig water pressure at the RO module inlet port. Permeate water is now produced by the membrane and fills the storage tank. When the storage tank water pressure reaches approximately 2/3 of line pressure (in this case 62 of 95 psig) the Kinetico Drinking Water System shuts down, preventing any more feed water from entering the membrane. On Plus units, the membrane is then flushed with permeate water. Then the bottom of the sump begins to depressurize. When the pressure falls to less than 10 psig, the pressure switch contacts open, shutting off the pump. The pump will remain off until enough water is consumed to lower the pressure in the storage tank to the turn on point of the R.O. system. Feed water now enters the inlet port, applying pressure to the membrane and the bottom of the module and starting the cycle over again. Notes and Cautions - Do not run pump dry for extended periods. The use of a Ground Fault Interrupter (GFI) is recommended and may be required locally. Consult and follow state and local codes for your specific area before starting installation. Always unplug pump before servicing. Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 11
Reverse Osmosis Accessories Kinetico Drinking Water System Plus 4 2 1. Water inlet from cold water supply (Plus units) 2. Water outlet discharge to RO prefilter inlet (Plus) 3. Signal line from bottom of RO module 4. Power cord 3 1 Specifications Size:...12.0" x 7.0" x 5.0" Maximum TDS:...TF membrane - 4000 ppm Maximum Feed Water Temperature:...100 F Maximum Feed Water Pressure:...60 psig Minimum Feed Water Pressure:...15 psig Power Requirements Voltage:...115 VAC Cycle:...60 Hz Tools and Supplies Required ¼" Allen Wrench Teflon Thread Tape Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 12
Reverse Osmosis Accessories Shurflo Booster Pump (part no. 9069A) Installation Kit (part no. 7281) 1 - Length of ¼" O.D. Tubing (part no. 8554A) 1 - Male Elbow, ¼" NPT X ¼" O.D. Tube (part no. 8551) 1 - Tee, Union, ¼" Tube (part no. 8748) 1 - Elbow, ¼ Tube X ¼ Stem (part no. 8958) Wrenches and Drain Saddle 1 Top View Bottom View 2 3 Dwg. No. Description Part No. 1 Wrench, Module 3960 2 Wrench, Sump 5223 3 Drain Saddle 4806 Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 13
Reverse Osmosis Accessories RO Fittings Part No. 8748 Tee, ¼" x ¼ x ¼ w/ metal gripper Parker True Seal fittings Part No. 10803A Flow Restrictor, Capillary, A200 Part No. 8553 Tee, ⅜" T x ¼" T x ¼" NPT Parker True Seal fittings Part No. 9410 Manifold Adapter Pin Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 14
Reverse Osmosis Accessories Part No. 8968 Tee, ⅜" x ⅜" x ⅜" Parker True Seal fittings Part No. 8561A Union Connector, ⅜" T x ¼" T Parker True Seal fittings Part No. 7761 Swivel Elbow Part No. 8574 3/8" diameter collet Parker True Seal fittings Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 15
Reverse Osmosis Accessories Part No. 8575A ⅜" diameter O-ring Parker True Seal fittings Part No. 3977 Gauge, low pressure Checking storage tank air pressure Part No. 5024 Assembly pressure test Used to check water pressure throughout R.O. unit Part No. 8563 1/4" diameter collet Parker True Seal fittings Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 16
Reverse Osmosis Accessories Part No. 8564A ¼" diameter O-ring Parker True Seal fittings Part No. 11439 Fitting,3/8 Adapter Ice Maker RO Tubing, Tools, and Fittings Part No. 1890 Tubing, ⅜" diameter x 100' Polyethylene Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 17
Reverse Osmosis Accessories Part No. 8586 Tool, Tubing Release Parker True Seal fittings Part No. 8552A Elbow, ¼" NPT x ⅜" tube Part No. 11378 Valve, Ball Tank ⅜ stem Part No. 8555 Tubing, ¼" diameter x 100' Polyethylene Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 18
Reverse Osmosis Accessories Part No. 8587 Tool, Tubing Cutter Parker True Seal fittings Part No. 8560 Ball Valve, ¼", Plastic Part No. 12866 Pressure Switch, Plus Deluxe Booster Pump Part No. 12855B 1/4" Diameter Collet Black Parker True Seal Fittings Revised: 07/2016 Drinking Water Systems Parts Pages Section 7 Page 19
Reverse Osmosis Accessories Part No. 12961A Kit Air Gap Part No. 9207A Tee, ⅜" x ⅜" x ¼ ¼ Collet is color coded orange Parker True Seal Fittings Section 7 Drinking Water Systems Parts Pages Revised: 07/2016 Page 20