High Reliability Hyperboloid Contacts ICO SERIES TM Technology Company, Inc.
integramate Hyperboloid Contacts QA Technology integramate TM Contacts are high quality, high reliability hyperboloid TM contacts intended for use in a wide range of applications. Our patented design provides lower insertion force, closer connector pin spacing, and better protection from damage than competitive designs. In addition, our automated manufacturing equipment typically allows us to ship within 24-48 hours of order. Competitive Advantages Socket Construction Details The integramate Hyperboloid Contact System has three clear advantages over existing hyperboloid contacts: 1. Lower and more uniform insertion and extraction force 2. Smaller contact diameter allows closer spacing and higher connector density 3. Better protection of the hyperbolic wire cage from accidental damage, since the cage lies behind a strong tubular entrance Features Low insertion/extraction force Low resistance Long cycle life Resistance to shock and vibration* Positive wiping action Easy contact removal using available extraction tools Small external contact diameter compared to other hyperboloid contacts allowing closer spacing Tubular entrance to protect spring wire cage and guide mating Intermates with other hyperboloid contacts known in the industry Applications High reliability connectors for: Medical & Dental Equipment ATE Interfaces Scientific Instruments Industrial Equipment Transportation Equipment Military & Aerospace Telecommunications & Data Communications * Contacts have been tested while installed in integramate circular connectors for resistance to vibration, shock, humidity, and corrosion. For details and test results, please contact QA. Technology Company 110 Towle Farm Road, Hampton, NH 03842 USA Tel: 603.926.1193 Fax: 603.926.8701
0.6mm Signal Contacts Type ICO60 SOCKETS PINS PCB Termination Ø.024 [0.61].157 [3.99] ICO60 A1 S1P1.808 [20.52].065 ICO60 A1 P1P1.065 1.018 [25.86] Ø.024 [0.61].157 [3.99] Solder Cup Termination Ø.034 [0.86] ICO60 A1 S1S5 ICO60 A1 P1S5 Ø.034 [0.86] Crimp Termination Ø.052 [1.32] Ø.057 [1.45] Ø.065 Ø.052 [1.32] Ø.024 [0.60] Ø.054 [1.37] Ø.065 Ø.052 [1.32].150 [3.81] ICO60 A1 S1C5.136 [3.45].798 [20.26].287 [7.29].413 [10.48].237 [6.02] ICO60 A1 P1C5.399 [10.13].289 [7.34] 1.011 [25.68].150 [3.81] Actual Size Specifications Mechanical Specification Insertion/Extraction Force 3.0 oz [85 g] typical Retention Force 5.0 lb [22.2 N] Durability (Cycle Life) Up to 100,000 Cycles Electrical Current Rating 4.0 Amps nominal (dependent upon mounting config., contact density, ambient temp., etc.) Contact Resistance 4.0 milliohms maximum, 3 milliohms typical Wire Size 22 26 AWG Crimp & Solder Cup Materials Contact Wires Beryllium Copper, ends not plated Spring Clip Beryllium Copper, not plated All other parts High conductivity copper alloys Plating 50 μ-inch of gold plating over nickel on all sliding contact surfaces 10 μ-inch minimum of gold plating over nickel on all other surfaces, except as noted ICO60 Pin / Socket Engagement Lengths.225 MAXIMUM INSERTION DEPTH.155 FULL ENGAGEMENT OF WIRES.065.090 LENGTH INITIAL POINT OF WIPE OF CONTACT Ø.026 min. ENTRY Ø.0236 [0.6mm] NOMINAL MATING PIN Typical Dimensions for Mounting in Insulator DIMENSION TO SUIT APPLICATION*.006 [.15].205 [5.21].304* [7.72].129 [3.28].288 [7.32].133 [3.38] Ø.073 [1.85] Ø.056 [1.42] Ø.066 [1.68] Ø.075 [1.91] All specifications subject to change without notice. All dimensions are in inches [mm]
1.5mm Power Contacts Type ICOA5 SOCKETS PINS Ø.100 [2.54] Ø.105 Ø.113 [2.67] [2.87].097 [2.46] Ø.083 [2.11] Ø.059 Ø.083.097 Ø.113 [1.50] [2.11] [2.46] [2.87] Ø.100 [2.54] Solder Cup Termination Ø.067 [1.70] ICOA5 A1 S1S8 ICOA5 A1 P1S8 Ø.067 [1.70] Crimp Termination.170 [4.32] ICOA5 A1 S1C8.136 [3.45].795 [20.19].040 [1.02].410 [10.41].302 [7.67] ICOA5 A1 P1C8.389 [9.88].040 [1.02] 1.066 [27.08].170 [4.32] Actual Size Specifications Mechanical Insertion/Extraction Force Retention Force Durability (Cycle Life) Electrical Current Rating Contact Resistance Wire Size Materials Contact Wires Spring Clip All other parts Plating Specification 4 oz [114 g] typical 5.0 lb [22.2 N] Up to 100,000 Cycles ICOA5 Pin / Socket Engagement Lengths Typical Dimensions for Mounting in Insulator 12.0 Amps nominal (dependent upon mounting config., contact density, ambient temp., etc.) 2 milliohms maximum, 1.5 milliohms typical 16 20 AWG Crimp & Solder Cup Beryllium Copper, ends not plated Beryllium Copper, not plated High conductivity copper alloys 50 µ-inch of gold plating over nickel on all sliding contact surfaces 10 µ-inch minimum of gold plating over nickel on all other surfaces, except as noted DIMENSION TO SUIT APPLICATION*.205 [5.21].225 MAXIMUM INSERTION DEPTH.140 FULL ENGAGEMENT OF WIRES.070.070 LENGTH INITIAL POINT OF WIPE OF CONTACT.006 [.15] Ø.060 min. ENTRY Ø.059 [1.5mm] NOMINAL MATING PIN www.qatech.com/integramate.199* [5.05].200 [5.08].045 [1.14].410 [10.41] Ø.104 [2.64] Ø.087 [2.21] Ø.114 [2.90] Ø.123 [3.12] All specifications subject to change without notice. All dimensions are in inches [mm] For detailed product specifications, please contact QA Technology Company, Inc. at (603) 926-1193 or integramate@qatech.com.
integramate Hyperboloid Contact Ordering Information TM 0.6mm Contact Order Code: I C O 6 0 A 1 1 Contact Type Termination Type Wire Size P Pin P PCB 1 Ø.024 Solder Tail S Socket C Crimp 5 22-26 AWG S Solder Cup 1.5mm Contact Order Code: I C O A 5 A 1 1 8 Contact Type Termination Type Wire Size P Pin C Crimp 8 16-20 AWG S Socket S Solder Accessories and Tools for ICO60 (0.6mm) Contacts ITC-100 Crimping Tool Daniels AFM8 crimping tool (contact positioner not included) ITP-O60 Contact Positioner Positions 0.6 mm contacts in Daniels AFM8 crimping tool ITE-O60 Contact Extraction Tool Extracts 0.6 mm contacts from dielectric Accessories and Tools for ICOA5 (1.5mm) Contacts ITC-200 Crimping Tool Daniels AF8 crimping tool (contact positioner not included) ITP-OA5 Contact Positioner Positions 1.5 mm contacts in Daniels AF8 crimping tool ITE-OA5 Contact Extraction Tool Extracts 1.5 mm contacts from dielectric ITP-O60 Positioner for 0.6 mm Contacts ITE-O60 Extraction Tool for 0.6 mm Contacts ITC-100 & ITC-200 Crimping Tools ITE-OA5 Extraction Tool for 1.5 mm Contacts ITP-OA5 Positioner for 1.5 mm Contacts www.qatech.com/integramate All specifications subject to change without notice. All dimensions are in inches [mm]. ISO 9001:2000
About QA Technology QA Technology was founded in 1981 and has since been recognized as a worldwide leader in the manufacture of high quality spring contact test probes. QA designs and builds its own flexible, high-speed automatic assembly equipment, which allows us to typically ship orders within 24-48 hours. Now QA Technology brings the same high quality and manufacturing speed to the hyperboloid contact market. TM Technology Company, Inc. 110 Towle Farm Road Hampton, NH 03842 USA Tel: 603.926.1193 Fax: 603.926.8701 www.qatech.com/integramate 2007 QA Technology, Inc. All Rights Reserved.