c GmbH Annex to the Accreditation Certificate D-PL-11086-01-00 according to DIN EN ISO/IEC 17025:2005 period ofvalidity: 05.08.2015 to 04.08.2020 Dateofissue: 05.08.2015 Certificate Holder: IFO - Institut für Oberflächentechnik GmbH Alexander-von-Humboldt-Straße 19, 73529 Schwäbisch Gmünd Tests in the fields: Testing of coatings or metal and plastic surfaces against corrosion, climatic or environmental impact and other contamination factors; Corrosion analyses, including chemicat, physico-chemical tests on metallic and non-metallic coatings and structural elements äs well äs metallic and plastic surfaces and coatings; Testing of mechanical properties of coatings; Testing of performance properties of coatings with selected non-destructive testing Abbreviations used : please referto the last page The testing laboratory is permitted, without being required to inform and obtain prior approval from, to use Standards or equivalent testing methods listed here with different issue dates. This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/8
Annex to accredltation certificate D-PL-11086-01-00 c l. Chemical and physico tests testing on coatings and corrossion DINEN ISO 3613 2011-04 DIN EN 15205 2007-02 Metallic and other inorganic coatings - Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zincaluminium alloys - Test methods Determination of hexavalent chromium in corrosion protection layers - Qualitative analysis (withdrawn Standard) HausmethodeOB 2009-11 Residual soiling for particle greater 150 \i m in metallic components DIN EN ISO 10523 2012-04 Determination of ph DIN 38404-4 1976-12 Determination oftemperature (C 4) DIN EN 27888 1993-11 Water quality; determination of electrical conductivity DIN EN 12373-4 1999-04 ISO 2143 2010-07 DIN EN ISO 2143 2010-12 Aluminium and aluminium alloys - Anodizing - Part 4: Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye Spot test with prior acid treatment (withdrawn Standard) Anodizing of aluminium and its alloys - Estimation of loss of absorptive power of anodic oxidation coatings after sealing - Dye- Spot test with prior acid treatment DIN EN 12373-7 2002-11 DIN EN ISO 3210 2010-12 Aluminium and aluminium alloys - Anodizing - Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment (withdrawn Standard) Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution Perlod ofvalidity: 05.08.2015 to 04.08.2020 -Transtation - 2/8
Annextoaccreditation certificate D-PL-11086-01-00 c 2. Testing of mechanical properties of coatings 2.1 Mechanical properties in air 2.1.1 mechanical and physical testing of deformation behaviour and failure limits of aluminium and steel coatings in air DIN EN ISO 1519 2011-04 Paints and varnishes - Bend test (cylindrical mandrel) DIN EN ISO 1520 2002-04 Paints and varnishes - Cupping test (withdrawn Standard) DIN EN ISO 1520 2007-11 Paints and varnishes - Cupping test DIN EN ISO 2409 1994-10 Paints and varnishes - Cross-cut test (withdrawn Standard) DIN EN ISO 2409 2013-06 Paints and varnishes - Cross-cut test DIN EN ISO 6272-2 2011-11 Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter DIN EN ISO 2815 2003-10 Paints and varnishes - Buchholz indentation test RAL-GZ 632 2011-08 Applicable test guideline Clause 1-3.2 Cleaning and protection - Fa^ade and monument - Quality assurance ASTM D 2794 2010 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) BS 6161 Part 18 1991-12 Methods of test for anodic oxidation coatings on aluminium and its alloys. Determination ofsurface abrasion resistance GSBAL631 Part VII Clause 10 International high-class directive for the component coating of aluminium - behaviour compared with drilling and milling -Translation - 3/8
Annex to accreditation certiflcate D-PL-11086-01-00 2015-01 Clause 2.18 Sawing, milling and drilling / regulation for determining the adhesion strength of an organic coating during mechanical processing 2.2. Mechanical properties in media 2.2.1 mechanical testing of properties GSB ST 663 Part VII Clause 8.2 Crosslinking test / polymerization test / wiping test International quality guideline for component coatings made of steel GSBAL631 Part VII Clause 8.2 Cross-linking test / Polymerization lest / Wiping test International quality guideline for component coatings made of aluminium QIB 2013-03 Clause2.10 Cross-linking test - Test for the determination of the degree of curing of liquid paints 2015-01 Clause2.14 Cross-linkingtest GSBAL631 PartVIICIauselS Resistance to boiling water / Cooking test International quality guideline for the component coating made of aluminium QIB 2013-03 Clause 2.12 Cooking test to check the pre-treatment 2015-01 Clause2.16 Resistance to boiling water / cooking test Period ofvalidity: OS.08.2015 to 04.08.2020 Dateofissue: 05.08.2015 - Translation - 4/8
Annex to accreditation certificate D-PL-11086-01-00 [(. 2.2.2 Testing of optical properties /colour fastness DI N 11664-4 2012-06 Colorimetry - Part 4: CIE 1976 L*a*b* Colour space DINEN ISO 2813 2015-02 Reflectometer äs a means for gloss assessment of plane surfaces of paint coatings and plastics DINEN ISO 2813 1999-06 Paints and varnishes - Determination of specular gloss of nonmetallic paint films at 20, 60 and 85" (withdrawn Standard) ISO 7724-2 1984-10 Paints and varnishes; Colorimetry; Part 2 : Colour measurement (withdrawn Standard) 2.3. Testing of media resistance due to aging, climatic and environmental impact äs well äs other contamination factors on laminated aluminium and steel and galvanic coatings DINEN ISO 6270-2 2005-09 Paints and varnishes - Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensationwateratmospheres DIN 50017 1982-10 Condensation water test atmospheres (withdrawn Standard) DINEN ISO 9227 2012-09 Corrosion tests in artificial atmospheres - Salt spray tests DIN 50021 1988-06 Spray tests with different sodium chloride solutions (withdrawn Standard) DIN EN ISO 6988 1997-03 Metallic and other non-organic coatings - Sulphur dioxide test with general condensation of moisture DINEN ISO 3231 1998-02 Paints and varnishes - Determination of resistance to humid atmospheres containing sulphur dioxide DIN 50018 Testing in a saturated atmosphere in the presence ofsulphur dioxide DIN EN ISO 7253 2002-04 Paints and varnishes - Determination of resistance to neutral salt spray (fog) (withdrawn Standard) -Translation- 5/8
Annex to accred itation certificate D-PL-11086-01-00.<^ RAL-GZ 632 2011-08 Applicable test guideline Clause 1-3.4 Cleaning of metal facades- alternative immersion test (Testing of cleaning agents for cleaning metal facades) RAL-GZ 632 2011-08 Applicable test guideline Clause 1-3.5 Cleaning of metal facades - cotton ball test (Testing of cleaning agents for cleaning metal facades) RAL-GZ 632 2011-08 Applicable test guideline Clause 1-3.3 Cleaning of metal facades - immersion test (Testing of cleaning agents for cleaning metal facades) GSBAL631 PartVIICIauselS International quality guideline for component coating made of aluminium - resistance to mortar GSB ST 663 PartVIICIauselS QIB 2013-03 Clause2.11 International quality guideline for component coatings made of steel - resistance to mortar Resistance to mortar Clause 2.15 Resistance to mortar DIN EN ISO 105-B02 2014-11 DIN EN ISO 16474-2 2013-03 QIB 2013-03 Clause2.9 Tests for colour fastness - Part B02: Colour fastness to artificial light: Xenon arc fading lamp test Paints and varnishes - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps Machu test (short-term corrosion test for aluminium, steel and galvanized steel) 2015-01 Clause2.11 Machu test (short-term corrosion lest, only on profile pieces) -Translation - 6/8
Annex to accreditation certificate D-PL-11086-01-00.^=^ Akkredltierungsstelle DINEN ISO 2931 2010-12 ISO 2931 2010-07 Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance Caterpillar Specifications 1E2732 (2010-01) 1E4093 (2012-12) Laboratory Cyclic Corrosion Test according to SÄE J 2334 (2003-12) - resistance against fluids (MG1004-151) 3. Testing of performance properties of coatings or metallic, plastic surfaces with selected non-destructive testing ISO 2177 2003-03 Metallic coatings - Measurement of coating thickness - Coulometric method by anodic dissolution Hausmethode 02 2008-07 Materialography - General Joint Preparation / Coating Thickness Determination DINEN ISO 2178 1995-04 DIN EN ISO 2360 2004-04 Hausmethode 01 2004-12 Non-magnetic coatings an magnetic Substrates - Measurement of coating thickness - Magnetic method (withdrawn Standard) Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness - Amplitudesensitive eddy current method Conductance measurement: The process is used to differentiate aluminium alloys by different conductivities Abbreviations used: ASTM American SocietyforTesting and Materials BS British Standard Caterpillar Published test guidance on coatings of U.S. American Company Caterpillar Inc. Specifications Manufacturerofconstruction machinery DIN German Institut ofstandardisation EN European Standard ISO International Organization for Standardization GSB ST Quality community of coatings of steel structural elements Quality community of organic coatings of aluminium structural elements in Architecture Dateofissue: 05.08.2015 -Translation - 7/8
Annex to accreditation certificate D-PL-11086-01-00 / QIB Quality communitv Industrial coating Hausmethode In-house test method of ifo - Institut für Oberflächentechnik GmbH RAL-GZ RAL-QualityLabel SÄE Standard from ANSI - American National Standards Institute -Translation - 8/8