STAINLESS STEEL HYGIENIC, DECORATIVE AND EXTREMELY TOUGH

STAINLESS STEEL HYGIENIC, DECORATIVE AND EXTREMELY TOUGH

STAINLESS STEEL RUST, ACID AND HEAT-RESISTANT STAINLESS STEEL SHEETS Clients from industry and trade have been using our experience and comprehensive stocks for more than 25 years. Important markets are the food industry, the domestic technology industry, engineering, the chemical and automotive industries as well as the medical industry. You will find the size and quality that you are looking for in the range of over 1,500 products that we always have in stock. You benefit from a logistically advantageous and concentrated range of products in one place. Should you prefer decorative finishes we surface-finish stainless steel sheets by grinding, brushing and coating on our own two high-performance processing lines. Stainless steel pipes as well as stainless steel, rolled or drawn, are also available with ground or polished surfaces. We use international contacts to realise special customer wishes in the field of coils and strips. cold-rolled sheet hot-rolled sheet Heat-resistant sheet pattern-rolled sheet Tear plate 1.4016 1.4301 1.4541 1.4571 1.4404 1.4512 2B (IIIc) 2R (IIId) ground brushed film 0.30 x 1,000 x 2,000-6.00 x 1,500 x 3,000 mm 1.4301 1.4541 1.4571 1.4404 1D (IIa) 2.00 x 1,000 x 2,000-30.00 x 1,500 x 3,000 mm 1.4828 1.4841 1.4878 2B (IIIc) 2C (IIIs) 1D (IIa) 1C (Ic) 1.00 x 1,000 x 2,000-12.00 x 1,500 x 3,000 mm 1.4016 1.4301 Linen Leather Rhombus Squares 5WL 0.50 x 1,000 x 2,000-2.00 x 1,500 x 3,000 mm 1.4301 Mandorla 3.00 x 1,000 x 2,000-6.00 x 1,500 x 3,000 mm Processing Grinding Grain 80 to 400 Brushing Grinding + Brushing Film coating max. width 1,500 mm max. length 4,500 mm Material thickness 0.40-6.00 mm Second choice second choice sheets second choice wide coils and strips third coice sheet and coilends

PROCESSING We can realise your desired finish with our processing machines. Grinding with grain 80-400 0.70-5.00 mm Brushing 0.40-6.00 mm Duplo ground / microlon ground (Grinding and brushing) 0.70-5.00 mm Custom grinding to customer s specification/ pattern 0.40-5.00 mm Protective film coating 0.40-6.00 mm also available with two-sided finishing Max. width 1,500 mm Max. length 4,500 mm We can grind/brush stainless steel plate and stainless steel perforated plate (grease-free) Film coating is possible with Stainless steel plate Aluminium plate Perforated plate (grease-free) cold-rolled/galvanized plate (clean/grease-free) Brass, copper, Hastelloy, zinc... Synthetic plates Hire work: we will also carry out this processing on your goods! Work done at short notice good value processing modern processing and warehousing technology Film Type Usage/Characteristics UV-protection Description 100 my laser film (standard NC 4224 or Laser cutting; heavy load Y top white bottom black; blue stripes on our warehouse stocks) PF 564C high adhesiveness and longitudinal arrows 90 my film NC 4204 white heavy load; medium adhesiveness N white; blue longitudinal stripes 80 my film NC 4223 or heavy load Y top white bottom black PF 562C medium adhesiveness blue longitudinal stripes 70 my film NC 4504 heavy load; medium adhesiveness N blue-transparent 60 my film NC 4105 low load; low adhesiveness N blue-transparent 50 my film NC 4951 acrylic glue for brass and copper N blue-transparent medium load; medium adhesiveness STAINLESS STEELS/HEAT-RESISTANT STEELS Chemical composition Mechanical characteristics at room temperature Comparison with various norms Mate- Structure Code name C Si Mn Cr Mo Ni Other Delivery 0,2% - Tensile Breaking Scale AISI GOS rial- % % % % % % % condition proof- strength elongation resistance USA GUS No. K= cold- stress in air max. max. max. max. rolled Rp 0,2 Rm up to W= hot- N/mm 2 N/mm 2 % C rolled min. min. Rustfree steel 1.4003 Ferritic X2CrNi12 0.03 1.00 1.50 10.50-12.50 0.30-1.00 N: 0.030 K 320 450-650 20 S40977 W 320 450-650 20 1.4016 Ferritic X6Cr17 0.08 1.00 1.00 16.00-18.00 K 280 450-600 20 430 12 Ch17 W 260 450-600 18 1.4034 Martensitic X46Cr13 0.43-0.50 1.00 1.00 12.50-14.50 K max. 780 12 (420) 40Ch13 W max. 780 12 1.4301 Austenitic X5CrNi18-10 0.07 1.00 2.00 17.00-19.50 8.00-10.50 N: 0.11 K 230 540-750 45 304 08Ch18N10 W 210 520-720 45 1.4306 Austenitic X2CrNi19-11 0.03 1.00 2.00 18.00-20.00 10.00-12.00 N: 0.11 K 220 520-670 45 304L 03Ch18N11 W 200 520-670 45 1.4307 Austenitic X2CrNi18-9 0.03 1.00 2.00 17.50-19.50 8.00-10.00 N: 0.11 K 220 520-670 45 304L 04Ch18N10 W 200 520-670 45 1.4310 Austenitic X10CrNi18-8 0.05-0.15 2.00 2.00 16.00-19.00 < 0.80 6.00-9.50 K 250 600-950 40 (301) W 1.4401 Austenitic X5CrNiMo17-12-2 0.07 1.00 2.00 16.50-18.50 2.00-2.50 10.00-13.00 K 240 530-680 40 316 W 220 530-680 40 1.4404 Austenitic X2CrNiMo17-12-2 0.03 1.00 2.00 16.50-18.50 2.00-2.50 10.00-13.00 N: 0.11 K 240 530-680 40 316L W 220 530-680 40 1.4435 Austenitic X2CrNiMo18-14-3 0.03 1.00 2.00 17.00-19.00 2.50-3.00 12.50-15.00 N: 0.11 K 240 550-700 40 316L 03Ch17N14 W 220 550-700 40 M2 1.4439 Austenitic X2CrNiMoN17-13-5 0.03 1.00 2.00 16.50-18.50 4.00-5.00 12.50-14.50 N: 0.12-0.22 K 290 580-780 35 S31726 W 270 580-780 35 1.4509 Ferritic X2CrTiNb18 0.03 1.00 1.00 17.50-18.50 Ti: 0.10-0.60 K 250 430-630 18 S43940 3 x C+0.30 Nb 1.00 1.4512 Ferritic X2CrTi12 0.03 1.00 1.00 10.50-12.50 6 x (C+N) Ti 0.65 K 220 380-560 25 409 W 220 380-560 25 1.4539 Austenitic X1NiCrMoCu25-20-5 0.02 0.70 2.00 19.00-21.00 4.00-5.00 24.00-26.00 N: < 0.15 K 240 530-730 35 N08904 Cu: 1.20-2.00 W 220 530-730 35 1.4541 Austenitic X6CrNiTi18-10 0.08 1.00 2.00 17.00-19.00 9.00-12.00 5 x C < Ti < 0.70 K 220 520-720 40 321 08Ch18N10T W 200 520-720 40 1.4571 Austenitic X6CrNiMoTi17-12-2 0.08 1.00 2.00 16.50-18.50 2.00-2.50 10.50-13.50 5 x C < Ti < 0.70 K 240 540-690 40 316Ti 10 Ch17N13 W 220 540-690 40 M 2 T Heat-resistant steel 1.4878 Austenitic X8CrNiTi18-10 0.10 1.0 17.00-19.00 9.00-12.00 5 x C Ti 0.8 190 500-720 40 850 321H 12 Ch18N10T 1.4828 Austenitic X15CrNiSi20-12 0.20 1.5-2.5 19.00-21.00 11.00-13.00 230 550-750 28 1,000 1.4845 Austenitic X8CrNi25-21 0.10 1.5 24.00-26.00 19.00-22.00 210 500-700 35 1,050 310/310S 1.4841 Austenitic X15CrNiSi25-20 0.20 1.5-2.5 24.00-26.00 19.00-22.00 230 550-750 30 1,150 No responsibility is taken for the correctness of these specifications, made in accordance with DIN EN 10 088-2 or 10 095. This page was made with the friendly help of ThyssenKrupp Nirosta. Other materials, special analyses on request.

FINISHES Execution and surface quality for plate and strip Abbre- Execution Surface quality / Note former viation designation 1C Warm-rolled, heat-treated, covered with mill scale I c not descaled for heat-resistant quality 1.4841 1E Warm-rolled, heat-treated, Scale-free, mechanically descaled, e.g. by II a mechanically descaled grinding or blasting. 1D Warm-rolled, heat-treated, Scale-free, Standard for most warm-rolled IIa or pickled types of steel. Not as smooth as C2 or 2D or 2B. No.1 2H Cold-hardened Bright III a Cold recast to achieve greater hardness. 2C Cold-rolled, heat-treated, Smooth, with scale from heat treatment III s not descaled for heat-resistant quality 1.4841 2D Cold-rolled, heat-treated, Smooth III b pickled Good reworkability, but not as smooth as 2B or 2R. 2B Cold-rolled, heat-treated, Smoother than 2D III c pickled, cold re-rolled Standard for most cold-rolled types of steel. 2R Cold-rolled, bright-annealed Smooth, bright, reflective IIId or Smoother and brighter than 2B. BA 2G Ground Grain between 80 and 400 IV available. 2J Brushed Smoother than ground. 2M Patterned Various patterns available, such as linen, leather, rhombus or squares. The back is smooth here Other patterns like 5WL are embossed. Special models Cold-rolled Warm-rolled Reference values: Thickness tolerances for cold-rolled plate and strip Thickness in mm 0.30-0.50-0.60-0.80-1.00-1.20-1.50-2.00-2.50-3.00-4.00-5.00 - Width in mm 0.49 0.59 0.79 0.99 1.19 1.49 1.99 2.49 2.99 3.99 4.99 6.00 up to 1,000 ± 0.04 ± 0.045 ± 0.05 ± 0.055 ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.11 ± 0.13 ± 0.14 ± 0.15 1,000-1,300 ± 0.04 ± 0.05 ± 0.05 ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.10 ± 0.12 ± 0.14 ± 0.15 ± 0.15 over 1,300 ± 0.06 ± 0.07 ± 0.08 ± 0.10 ± 0.11 ± 0.12 ± 0.14 ± 0.15 ± 0.16 * ± 0.03 ± 0.04 ± 0.04 ± 0.04 ± 0.05 ± 0.05 ± 0.06 ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.10 STAINLESS STEEL PIPES Profile pipe 1.4301 1.4571 HF or WIG welded, non-brazed Square pipes 10 x 10 x 1.00-200 x 200 x 5.00 mm Rectangular pipes 20 x 10 x 1.00-300 x 100 x 5.00 mm Decoration and construction tubing DIN 17455 1.4301 1.4571 HF or WIG welded, non-brazed or brazed 6.00 x 1.00-168.3 x 5.00 mm EN ISO 1127 Conduit pipes DIN 17457 1.4301 1.4571 WIG or laser welded, non-brazed or brazed 6.00 x 1.00-168.3 x 5.00 mm EN ISO 1127 STRIPS/COILS/ZUSCHNITTE Product Cold-rolled strip Surface Thickness Width Warm-rolled strip Surface Thickness Width further options: 1.4512 1.4016 1.4301 1.4541 1.4571 1.4404 2B (IIIc) 2R (IIId) ground brushed film 0.30-6.00 mm 5.00-2,000 mm EN 10259 1.4003 1.4541 1.4571 1.4404 2E (IIa) 2.00-8.00 mm 20.00-2,000 mm EN 10051 Slit strip for vehicle exhausts Decoiling of fixed dimension sheets Flat bars, cut, calibrated Roller aligned Aligned Precision strip in accordance with EN10258 STAINLESS STEEL BARS Flat rolled steel Round steel bar Railings Angels Square steel wire NOT JUST ROUND STAINLESS STEEL BRIGHT BARS Our bright steel range is comprehensive and thanks to exact tolerances ideal for use in industries where precision and surface quality are critical. Our advantage: the entire range is also available in stainless steel. 1.4301 1.4541 1.4571 1.4828 1.4841 Cut corner, classic rolled or ground grain 240 10 x 2.00-200 x 20.00 mm / HL 4 m oder 4-6 m DIN 1017 1.4301 1.4305 1.4541 1.4571 1.4404 1.4828 1.4841 rolled or rolled/peeled 20-400 mm / HL 4-6 m DIN 1013 1.4301 Brushed or ground grain 240 Rund 8-10 - 12-14 - 20 mm / HL 6 m DIN 668/671 1.4301 1.4571 rolled 20 x 20 x 3-100 x 100 x 10 mm / HL 6 m DIN 1028 1.4301 1.4571 rolled 20 x 150 mm / HL 4-6 m DIN 1014 All dimensions, materials and details can be found in the individual brochure Stainless steel, bright bars. For further information: vbl@holzrichter-stahl.de. brushed or ground Mandorla 5WL Linen (25) Rhombus (22) Squares (21) Leather (42) * These tolerances are possible for new production upon production of a complete coil.

ESSEN A42 A40 A43 BOCHUM A44 A45 DORTMUND HERDECKE A44 WITTEN A43 HERDECKE ISERLOHN A45 AS-- BARMEN SCHÜTZENSTR. AS-- WICHLINGHSN. AS- - OST 7 SCHÖNE- BECKERSTR. FRIEDRICH- ENGELS-ALLEE CARNAPER- STR. 7 SCHÖNEBECKER PLATZ 11 51 51 Administration Office: Schönebecker Platz 11, D-42283 Wuppertal Supply and dispatch warehouse in the Loh industrial park Access via Schönebecker Straße Phone: +49 (0) 202 5 62-0 Fax: +49 (0) 202 5 62-278 YOUR CONTACTS:ÄN Angelika Bäcker Phone: +49 (0) 202 5 62-174, Fax: +49 (0) 202 5 62-259 Email: a.baecker@holzrichter-stahl.de Larissa Bergmann Phone: +49 (0) 202 5 62-104, Fax: +49 (0) 202 5 62-259 Email: l.bergmann@holzrichter-stahl.de Stefan Bergs Phone: +49 (0) 202 5 62-100, Fax: +49 (0) 202 5 62-259 Email: s.bergs@holzrichter-stahl.de Christian Martin Phone: +49 (0) 202 5 62-252, Fax: +49 (0) 202 5 62-259 Email: c.martin@holzrichter-stahl.de Wolfgang Matzolleck Phone: +49 (0) 202 5 62-297; Fax: +49 (0) 202 5 62-259 Email: w.matzolleck@holzrichter-stahl.de Axel Sticher Phone: +49 (0) 202 5 62-256, Fax: +49 (0) 202 5 62-259 Email: a.sticher@holzrichter-stahl.de Sylvia Kroll Phone: +49 (0) 202 5 62-274, Fax: +49 (0) 202 5 62-259 Email: s.kroll@holzrichter-stahl.de Peter Holzrichter GmbH Postfach 200764, D-42207 Wuppertal Email: info@holzrichter-stahl.de Web: www.holzrichter-stahl.de A company of the -Group