Assembly Instructons Model: 235SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH:.52m FRONT WALL HEIGHT:.8m REAR WALL HEIGHT: 2.08m CONCRETE SLAB 620mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosng an Australan made shed. For further assstance please vst our detaled nstructonal vdeo lbrary at Http://www.abscosheds.com.au/watch-vdeos At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. feedback@absco.com.au ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE
Model: 235SK GENERAL INSTRUCTIONS Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. An uneven surface may result n msalgnment of parts. It s recommended that the shed be set on a 00mm concrete slab and anchored down approprately (refer to last page for detals). Anchor sets are not suppled as standard tems wth ths product as some customers wsh to use ther own anchorng systems. TOOLS REQUIRED OPTIONAL A NOTE ON SAFETY Normal: 4mm & 0mm Masonry: 0mm Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 2
Model: 235SK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 2 STEEL SHEET 2045 X 773mm 262 WITH HINGES L = 725mm 58A STEEL SHEET 2045 X 773mm 263 L = 725mm 58B STEEL SHEET 95mm X 773mm 260L 2 L = 773mm 58C STEEL SHEET 95mm X 773mm 260R 2 L = 530mm 6D STEEL SHEET 2045mm X 773mm 26L L = 788mm 79B STEEL SHEET 2045mm X 773mm 26R 2 L = 53mm 8E 3 STEEL SHEET 60mm X 773mm 43S 2 STEEL SHEET 785mm X 73mm 32A STEEL SHEET 725mm X 773mm B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 3
Model: 235SK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 6 JOINER L= 200mm (7.9") CSJ THESE COMPONENTS ARE TO BE JOINED TO THESE COMPONENTS 2 L = 26.5mm 8CL 2 L = 26.5mm 8CR L = 26.5mm 54AL L = 26.5mm 54AR L = 26.5mm 54BL L = 26.5mm 54BR L = 26.5mm 54CL L = 26.5mm 54CR L = 26.5mm 8DL L = 26.5mm 8DR ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 4
Model: 235SK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK JAMB L= 785mm 89A 2 JAMB L= 20mm 9A JAMB L= 785mm 89B 2 LIP TRIM L= 60mm 88J 220 JAMB L= 788mm 90B CONTENTS OF FITTINGS PACKET SELF TAPPING SCREWS DOOR PADBOLT 22A 6 4mm CSK SCREW & NUT SECURE HINGES TO DOOR DOOR PADBOLT HASP ASSEMBLY INSTRUCTIONS 6 3mm POP RIVETS SECURE HINGES TO DOOR (ALTERNATIVE FIXING METHOD) DOOR STRAP L: 65mm 2A ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 5
Model: 235SK INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP. Poston the channels and the CSJ joner channel so the center of the CSJ s n lne wth the end of each channel to be joned together. STEP 2. Jon the frst channel to the CSJ by nsertng the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text s marked. Push down one sde of the CSJ untl you hear a 'clck'. = = JOIN>> <<JOIN JOIN>> = <<JOIN = DRILL 4mm (0.6") x 3mm (0.2") (2 PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) STEP 3. Jon the second channel to the CSJ by postonng the <<JOIN end of the channel at the center of the CSJ (on an angle). Push the CSJ nto the channel untl you here a 'clck'. FINISHED The joned channels should now look lke the pcture above wth the CSJ postoned equally nsde of the joned channels. PUSH QTY = 0pcs. CSJ PUSH CSJ CSJ CSJ HIGH-SIDE CSJ LOW-SIDE 20mm (0.79") CSJ 5mm (0.59") ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 6
Model: 235SK STEP. PRE-ASSEMBLY OF SPLICED S NOTE: JOIN TOGETHER 2 X SECTIONS USING 6 X JOINERS (PART CSJ) 2 X 8CR 2 X 8CL X 54AR X 54AL X 54CR X 54CL NOTE: SOME S HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY WHERE THE CSJ JOINING COVERS HOLES ON THE S YOU ARE CONNECTING 2253mm (88.7") 8CL 8CR 54CL 54CR 54AL 54AR 8DR 54BL 54BR = = = = = 2 x 8C x 54A x 54C x 54B x 8D X 54BR X 54BL 8DL X 8DR X 8DL ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 7
Model: 235SK VIEW OF ROOF COMPONENTS 8C 88J 43S 43S 43S 88J 8C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 8 NO.
Model: 235SK 54B 262 26L 262 263 6D 90B 26R 260R 32A 89A 89B 8D 79B 8E 54C VIEW OF WALL COMPONENTS ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 22A 260L 32A 6D 9A 54A 8E B PAGE 9
Model: 235SK ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst. Use one component as a template to mark where the holes are. Drll wth 3mm drll bt. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 Each permeter channel must fnsh flush wth the edges of the sheets.the snaptte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. If you need to remove channels from the panels, pull the channel along the panel from opposng ends. You may need someone to help wth ths. 3mm POP RIVETS 4mm NUT & BOLT SET PAGE 0
Model: 235SK DOOR 6. DOOR PANEL ASSEMBLY 58C 58A 58B B 2A 58C ALL VERTICAL DOOR S ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR S 20mm FLANGE B 5mm FLANGE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE
Model: 235SK REAR PANEL ASSEMBLY 262 263 262 54B 8D ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 2
Model: 235SK SIDE PANEL ASSEMBLY x LEFT SIDE PANEL x RIGHT SIDE PANEL 260R 26R 26L 260L 6D 8E 6D 8E ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 3
Model: 235SK ROOF PANEL ASSEMBLY 43S 43S 43S 8C 88J 88J 8C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 4
Model: 235SK FRONT PANEL ASSEMBLY 89A 89B 32A 32A 54A 90B SNAP T TE 79B 54C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 5
Model: 235SK 9A B 9A B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. poston each hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 6
Model: 235SK PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not postoned upsde down. The top channel of each panel s pre-punched for attachng roof sheet. The base channels are not pre-punched. SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 7
Model: 235SK FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 2 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 235SK 5/04/6 PAGE 8
AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS Congratulatons on your purchase of an ABSCO SHED ABSCO SHEDS, ncludng garden sheds, garden beds, avares, storage unts, garages, awnngs and carports are made usng hgh qualty Australan made steel. We are pleased to advse we warrant that the steel coatng wll not rust, crack, flake peel or blster for 20 years from date of purchase, when nstalled wthn Australa. Ths warranty does not apply to surface deteroraton of panels caused by Swarf (Tny partcles of steel debrs left from cuttng, grndng or drllng operatons) that has not been removed after buldng constructon, or as a result of contact wth damp sol, chemcals, fertlsers or other corrosve substances. Ths warranty covers any Absco product used for normal domestc use and nstalled n accordance wth the nstallaton nstructons. The warranty does NOT cover Damage caused by storms, wnd, ran snow or poor foundatons. Ths warranty does NOT cover ABSCO products nstalled n severe coastal, ndustral or other hghly corrosve envronments. The warranty does not cover fasteners (screws, nuts, bolts, rvets, hasps or bolts). The warranty s lmted to replacement and delvery of components and does not nclude any labour or nstallaton costs. The benefts gven by the warranty are n addton to your other rghts and remedes under a law n relaton to the goods or servces to whch the warranty relates. The warranty apples to the excluson of all other representatons, guarantees or warrantes express or mpled, our goods come wth guarantees that cannot be excluded under the Australan consumer law and s not transferable. You are enttled to a replacement or refund for a major falure and for compensaton for any other foreseeable loss or damage. You are also enttled to have the goods repared or replaced f the goods fal to be of an acceptable qualty and the falure does not amount to a major falure. For further nformaton go to http://www.consumerlaw.gov.au. Please retan a proof of purchase (sales docket or nvoce) or regster your warranty wthn 30 days of purchase here: www.absco.com.au/regster_warranty.php In the unlkely event a warranty clam s made, t must be supported by photographc evdence and detals of the defect, ncludng component part numbers, together wth proof of purchase documentaton (or on-lne regstraton of purchase) and forwarded to the address below. Upon recept of the warranty clam, the Customer Servce Manager wll contact you wthn three busness days to advse you of the assessment outcome of the clam, whch may nclude your expenses ncurred n makng the clam. THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 9 ACACIA RIDGE QLD AUSTRALIA 40 PHONE: 800 02970 FAX: 07-33449 EMAIL: warranty@absco.com.au Issued 0 January 202 P a g e
ABSCO SHEDS - STORAGE GUIDELINES ABSCO SHEDS nclude garden sheds, garden beds, storage unts, avares, garages, awnngs and carports. ABSCO SHEDS are desgned to be weatherproof for normal weather condtons. In the event of extreme weather condtons such as heavy ran, combned wth hgh wnd gusts, the rdge cappng, sheetng jons, screw fxngs etc., may exhbt mnor deformatons whch may allow some water entry. These areas should be checked regularly to ensure that maxmum strength and protecton s mantaned. Other weather condtons such as extreme heat and extreme cold, most or dry ar can nfluence the effects of concrete floor mosture and/or condensaton on the undersde of the roof sheets. ABSCO SHEDS and storage unts are prmarly used for storage of garden equpment such as lawnmowers, wheelbarrows, garden tools etc. Storage tems that mght be adversely affected by any of the above condtons may requre addtonal protecton such as beng sealed or covered by plastc sheets and/or stacked above the concrete floor on tmber slats. Waterproof sealants may be used to offer further protecton where requred around jons and screw fxngs, as can rubber door seals and other products whch are avalable from most hardware outlets. Placement of waterproof sealants (slcone) between the base of the shed and concrete slab s not recommended, as ths process can have a reverse effect, preventng excess water from escapng, resultng wth water accumulatng and beng trapped nsde the shed. Absco accepts no responsblty for water entry, floor mosture, condensaton or the condton of the Contents nsde your Absco steel buldng arsng from any of the pre-mentoned weather condtons. 2 P a g e