Handi-Mate TM Shed HINGED - TYPE HM4

Transcription

1 INSTALLATION GUIDE Handi-Mate TM Shed HINGED - TYPE HM4 HOLD DOWN LUGS MUST BE INSTALLED ACCORDING TO WIND CLASSIFICATION SHMSHSDHM4## WIND CLASSIFICATION N, N = x HOLD DOWN LUG (HMHL) N3 = 6x HOLD DOWN LUG (HMHL)

2 BEFORE YOU START Prior to installation, it is important that you contact your local government authority to determine if building approval is required. To ensure that the installation and erection of your Stratco Handi-Mate TM Shed proceeds smoothly you should confirm that all the components and materials listed on the delivery documentation, and in this installation guide, have been supplied. Carefully read this installation guide to familiarise yourself with all the steps involved, and ensure that you have the correct tools and equipment for the job. NOTE: Use heavy gloves when handling steel sheeting and flashings and never attempt to install a shed in windy conditions. TOOLS REQUIRED COMPONENTS x CORNER WALL SHEET SSPHMWSCNR900## WALL SHEET SSPHMWS900## ROOF SHEET SSPHMRS090AZ x4 x4 x4

3 3 SPLIT WALL SHEET DOOR ASSEMBLY SSPHMSW900## HDJAHDC## x x

4 4 LEFT HAND BARGE CAP HMBCHDRL0## RIGHT HAND BARGE CAP HMBCHDRR0## x x RIDGE CAP HMRC785GA RIDGE BEAM HMRB450GA DOOR SHROUD HMDSHDRBO80GA DOOR JAMB HMDJHDC900## 400 WALL CHANNEL HMWC400GA 00 WALL CHANNEL HMWC00GA x x x x x4 x4 RIV4-3 RIV4-3## WTK0 ALUMINIUM RIVET RIVET 0x WAFER TEKNNW06 TEK06 TEK05## 0x6 SCREW 0x6 WASHER SCREW 0x5 WASHER SCREW HMCBGA HMDTHDR HMTH DOOR HANDLE x DOOR TONGUE x CORNER BRACKET x8 MAA847 N/N N3 M8x47 MASONRY ANCHOR HMHL N/N N3 x6 x0 HOLD DOWN LUG x x6

5 5 SITE AND ASSEMBLY PREPARATION Preventing Wind Uplift All Stratco Handi-Mate TM Sheds must be securely bolted to a permanent concrete base with sufficient masonry anchors to prevent wind uplift. It is particularly important that masonry anchors are placed within all four corner brackets of the Handi-Mate TM Shed. Further anchors and mounting brackets are also used to fix the Handi-Mate TM Shed to the permanent concrete base according to shed size. The mounting brackets are to be evenly spaced along the length of the wall. Concrete Floor Option - Before building the shed, pour a base that is larger than the area by at least 00mm in each direction. The base should be poured so the concrete that will be outside the shed floor area slopes away from the shed to help prevent water from entering the shed. Option - Substantial concrete pads may be used at each anchor location as an alternative to a complete concrete floor. It is recommended pads are minimum Ø50mm x 400mm deep, embedded into a firm natural soil base Important Notes It is essential to clear and level the site prior to assembling your Stratco Handi-Mate TM Shed. Before starting to build the shed, please refer to the previous pages of this guide for a list of recommended shed assembly tools and shed components. Also note there are different types and colour screws. Ensure that the right type and colour screw is being used at each location. Stability and performance of the shed relies on the door being closed during high wind events. Do not traverse the roof of the Handi-Mate TM Shed. If this is unavoidable, ensure crawl boards or ladders are used over the roof surface to distribute the load.

6 6 DOOR ASSEMBLY 0x WAFER SCREW DOOR HANDLE DOOR TONGUE OPTIONAL DOOR FRONT WALL ASSEMBLY DOOR DOOR JAMB SPLIT WALL SHEET CORNER WALL SHEET

7 7 00 WALL CHANNEL 00 WALL CHANNEL 0x6 SCREW x4 3

8 8 BACK WALL ASSEMBLY CORNER WALL SHEET WALL SHEET WALL SHEET 00 WALL CHANNEL 00 WALL CHANNEL

9 9 0x6 SCREW x4 POSITION THE WALL SHEETS SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK. 3 0x6 SCREW POSITION THE WALL SHEETS SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK FOR ALL SCREWS. RIVET 0x6 SCREW 4

10 0 SIDE WALL ASSEMBLY CORNER WALL SHEET WALL SHEET 400 WALL CHANNEL 400 WALL CHANNEL

11 0x6 SCREW x4 POSITION THE WALL SHEET SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK. 3 0x6 SCREW POSITION THE WALL SHEET SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK. RIVET 0x6 SCREW 4

12

13 3 SHED ASSEMBLY MAKE SURE PRE-PUNCHED HOLES IN CORNER BRACKETS AND WALL PANELS ARE ALIGNED. CORNER BRACKET REPEAT PROCESS FOR THIRD WALL 0x6 SCREW

14 4 3

15 5 0x6 SCREW 4 CHECK DIAGONALS FOR SQUARE 5 MASONRY ANCHOR FIX TO CONCRETE ONCE SQUARE

16 6 USE DOOR SHROUD AS SPACER TEMPLATE BETWEEN BOTH DOOR JAMBS. FIX AT BASE. 0x6 SCREW DOOR SHROUD DOOR SHROUD 6 3 0x6 SCREW 3 3 RIVET 0x6 SCREW RIVET RIVET 3 7 RIVET

17 7 0x6 SCREW RIDGE BEAM 005mm 8 TURN UP VALLEYS ON SHEET TO ENCOURAGE WATER TO FLOW TOWARDS WALLS FIXING LOCATIONS FOR ALL ROOF SHEETS ALL SCREWS 0x6 WASHER SCREWS ALUMINIUM RIVET

18 8 RIDGE CAP RIDGE CAP RIDGE BEAM 5mm IN FROM BACK EDGE OF RIDGE CAP THEN CONTINUE WITH 300mm SPACING. RIDGE CAP 0x6 WASHER SCREW 0

19 9 0x5 WASHER SCREW LEFT BARGE CAP 0x5 WASHER SCREW FIX THROUGH DOOR JAMB 0mm MIN LEFT BARGE CAP FIX THROUGH DOOR JAMB RIGHT BARGE CAP RIGHT BARGE CAP

20 SECURE THE SHED CONTACT The installer is responsible for ensuring the slab or concrete squares are sufficient to support the shed and sustain wind loading. Do not directly anchor your shed to pavers. MAXIMUM DISTANCE BETWEEN HOLD DOWN LUGS (CENTRE TO CENTRE) IS DETERMINED BY WIND CLASSIFICATION WIND CLASSIFICATION N, N = 400mm MAXIMUM (CENTRE TO CENTRE) N3 = 900mm MAXIMUM (CENTRE TO CENTRE) FIX TO CONCRETE WITH MASONRY ANCHORS TEK06 MAX. DIST. MAX. DISTANCE MAX. DISTANCE MAX. DIST. MAX. DISTANCE HOLD DOWN LUG ALL HOLD DOWN LUG SCREWS SHALL BE SECURED THROUGH BOTH THE WALL CHANNELS AND WALL SHEETS. MAX. DIST. MAX. DISTANCE (NOT ACTUAL SHED) MAX. DIST. MAX. DIST. HANDY HINT SHEETS OFF GROUND DURING WALL ASSEMBLY MAINTENANCE Your Stratco Handi-Mate TM Shed will maintain its good looks for even longer with a simple wash and wipe down. Cleaning should be performed as often as is required to remove any dirt, salt and pollutants. Copyright April 06 4/04/6 All brands and logos/images accompanied by or are trade marks of Stratco (Australia) Pty Limited. Stratco Handi-Mate TM Sheds are produced from the highest quality materials and will provide many years of service. Refer to the Selection Use and Maintenance brochure for more information on how to get the best out of your product. BROCHSDHM4