TABLE OF ONTENTS Product Page No. Product Page No. Panel Information Vertical Seam Panel Profi les... PVS- Panel Overview... PVS- Flashing Profiles Eave... PVS- Extended Eave... PVS- leat... PVS- Offset leat... PVS- Box Gutter... PVS- Box Gutter End... PVS- Universal Gutter/Downspout Strap... PVS- " x / " Downspout... PVS- " x / " 95 Elbow... PVS- Downspout Bracket... PVS- Valley... PVS- Rake... PVS- Rakewall... PVS- ounter Flashing... PVS- Reglet Flashing... PVS- " Ridge/Hip over... PVS- SSR Ridge... PVS- Vented Ridge over... PVS- Vent Drip... PVS- Peak... PVS- Pitch Break... PVS- Z-losure... PVS-.5" Sill/Head... PVS-.5" Sill to Soffi t... PVS- Starter... PVS- Accessory Profiles Vertical Seam lip... PVS-5 Vertical Seam lip (UL-90)... PVS-5 Floating Rake Angle... PVS-5 Back-Up hannel... PVS-5 Bearing Plate... PVS-5 Vent Material... PVS-5 Rubber Roof Jack... PVS-5 Retro Roof Jack... PVS-5 Rubber Roof Flashing Kit... PVS-5 Tube Sealant... PVS-5 Tape Sealant... PVS-5 Touch-Up Paint... PVS-5 Metal Panel Hemming Tool... PVS-5 Design/Installation onsiderations Fastener Installation Technique... PVS-5 ondition of Substructure... PVS-5 Ventilation... PVS-6 Insulation... PVS-6 System Expansion/ontraction... PVS-7 Selection of System omponents... PVS-7 Detail onditions Eave Detail... PVS-8 Extended Eave Detail... PVS-9 Box Gutter Detail... PVS-9 Valley Detail... PVS-0 Rake (On Module) Detail... PVS- Rake (Off Module) Detail... PVS- Rake Parapet (On Module) Detail... PVS- Rake Parapet (Off Module) Detail... PVS- SSR Ridge/Hip Detail... PVS- Vented Ridge Detail... PVS-5 Highside Parapet Detail... PVS-5 Notes Notes... PVS-6 Testing Information UL 580 Wind Uplift Information...PVS-6- UL Fire Resistance Ratings... PVS- Section Properties and Load Tables... PVS- PVS-
PANEL OVERVIEW PANEL PROFILES Factory Applied Sealant /" Without Striations (Flat) ",6", or 8" overage Factory Applied Sealant /" With Striations ",6", or 8" overage SLOPE SUBSTRATE OVERAGE LENGTH AVAILABILITY APPLIATION PERFORMANE TEST FASTENING SYSTEM FASTENERS MATERIALS FINISH The minimum recommended slope for any Vertical Seam roofing panel is :. Vertical Seam is designed to be utilized over solid substrate, but can easily be used over an open structural framing. The recommended substrate is 5 /8" plywood with a 0 pound felt moisture barrier. To avoid panel distortion, use a properly aligned and uniform substructure. Vertical Seam panels are available in a ", 6", and 8" width with a /" rib height. Lengths under 5'-0" are available with some cutting restrictions. Maximum recommended panel length is 5'-0". Longer panels require additional consideration in packaging, shipping, and erection. Please consult your Metal Sales branch for recommendations (see PGI- and for locations). Vertical Seam panels are available in 6,, and gauge. Minimum quantities may apply. ommercial, Architectural, and Residential panel. UL 580, ASTM E-59, ASTM E-66, ASTM E-680, UL 790, UL 8, UL 6, Texas Department of Insurance, Miami-Dade ounty. oncealed lip System. The fastener selection guide should be consulted for choosing proper fasteners for specific applications. Quantity and type of fastener must meet necessary loading and code requirements (see PGI--). Steel grade 50, Per ASTM-A79 * Acrylic oated Galvalume (AG) / ASTM A-79 - AZ55 Prepainted Galvalume / ASTM A-79 - AZ50 ** Fluorocarbon (PVDF) * Differential appearance of Acrylic oated Galvalume roofing materials is not a cause for rejection. ** Meets both Kynar 500 and Hylar 5000 specifications. PVS-
EAVE FLASHING PROFILES EXTENDED EAVE LEAT 7 /8" X* " Hem 5 /8" X* 6" " 5 /8" /" /" /" 5 Length 0'-" - *Specify Slope Angle Length 0'-" *Specify Slope Angle Length 0'-" OFFSET LEAT BOX GUTTER BOX GUTTER END /" /" " /" X* 5" " Hem " " 5" " " " 5" 5" Length 0'-" UNIVERSAL GUTTER/ DOWNSPOUT STRAP Hem Length 0'-", 0'-" - *Specify Slope Angle DOWNSPOUT " x /" 95 0 ELBOW " x /" " /" " /" 6" DOWNSPOUT BRAKET /" VALLEY Length 0'-", 0'-" (Also available 6" x ") (Also available 6" x ") (Also available in 5 ) RAKE " " " X* 0" 5" RAKEWALL (Also available 6") Length 0'-", 0'-" - *Specify Slope Angle OUNTER FLASHING 5 /8" Hem Length 0'-", 0'-" REGLET FLASHING /" " 5 /8" " /" " " /" Hem Length 0'-", 0'-" /" Length 0'-" Hem Length 0'-" PVS-
" RIDGE/HIP OVER FLASHING PROFILES (ONT.) SSR RIDGE VENTED RIDGE OVER 5 /" X* 5 Hem X* " " " " Hem " " X* /8" 7 /8" Length 0'-", 0'-" - *Specify Slope Angle Length 0'-", 0'-" - *Specify Slope Angle Length 0'-", 0'-" - *Specify Slope Angle VENT DRIP /" 60 /" 0 PEAK 5" X* 6" PITH BREAK X* " /" /8" 6" Length 0'-" Length 0'-", 0'-" - *Specify Slope Angle Length 0'-", 0'-" - *Specify Slope Angle Z-LOSURE ".5" SILL/HEAD.5" SILL TO SOFFIT /" /" /" /" /" /" /" " Length 0'-" Length 0'-", 0'-" /" Length 0'-", 0'-" STARTER /" /" - Indicates color side of flashing. Length 0'-" PVS-
AESSORY PROFILES VERTIAL SEAM LIP VERTIAL SEAM FLOATING RAKE ANGLE UL-90 LIP Length 0'-0" Height / " Galvanized BAK-UP HANNEL BEARING PLATE VENT MATERIAL /8" 7 /8" " Length 8" and 7" Galvanized RUBBER ROOF JAK " X 5" RETRO ROOF JAK RUBBER ROOF FLASH KIT MINI ( /" to /8" O.D. Pipe) # ( /" to " O.D. Pipe) # (" to 6" O.D. Pipe) #6 (6" to 9" O.D. Pipe) #8 (7" to " O.D. Pipe) TUBE SEALANT #80RETRO ( /" to /" O.D. Pipe) #80RETRO (" to 7 /" O.D. Pipe) #80RETRO ( /" to 0" O.D. Pipe) TAPE SEALANT " x 50'-0" Flash Kit 8" x 50'-0" Flash Kit TOUH-UP PAINT 0. oz. artridge Urethane METAL PANEL HEMMING TOOL 7 /8" X /6" X 5' Double Bead Butyl - Gray Available in Pints PVDF / MS F0 PVS-5
UL 580 WIND UPLIFT INFORMATION See Item VERTIAL SEAM onstruction No. 5 February 05, 00 Uplift - lass 90 (See Item No. ) Fire Not Investigated. Metal Roof Deck Panels * No. MSG or No. MSG min thickness coated steel panels. Panels in. wide, -/ in. high at the ribs. Panels continuous over two or more spans. A bead of sealant may be used at panel side joints. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners * (Panel lips) One piece assembly, -/ in. wide, -7/8 in. high, thickness 0.08 in. One panel clip located at each purlin intersection. METAL SALES MFG ORP - Vertical Seam lip. Panel Fasteners (Screws) Fasteners used to attach panel clips (Item ) to purlins to be No. 0-6 by in. long No. self-drilling point, No. Phillips drive head, plated steel screws. Two screws per clip to be used inserted through / in. diameter guide holes.. Purlins No. 6 MSG min thickness steel (50,000 psi min yield strength). Spacing - For MSG thickness panels - 60 in. O For MSG thickness panels - 8 in. O U L Underwriters Laboratories Inc. LISTED PVS-6
UL 580 WIND UPLIFT INFORMATION (ONT.) See Item VERTIAL SEAM onstruction No. 55 January 0, 00 Uplift - lass 90 and 60 (See Item No. ) Fire Not Investigated. Metal Roof Deck Panels* No. MSG min thickness coated steel. Panel width 8 in. max., 0 in. min. Rib height -/ in. at female side. Panels continuous over two or more spans. A bead of sealant may be used at panel side joints. METAL SALES MFG ORP - Vertical Seam.. Roof Deck Fasteners* (Panel lips) - One piece assembly, -/ in. wide, -7/8 in. high. One panel clip located at each purlin intersection. METAL SALES MFG ORP - Vertical Seam lip.. Panel Fasteners (Screws) Fasteners used to attach panel clips (Item ) to purlins to be No. 0-6 by in. long plated pancake head No. phillips drive, No. self-drilling point steel screws. Two screws per clip to be used inserted through / in. diam guide holes.. Purlins No. 6 MSG min thickness steel (50,000 psi min yield strength). Spacing for lass 90 to be 8 in. O: For lass 60 to be 60 in. O Refer to General Information Roof Deck onstructions for items not evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-7
UL 580 WIND UPLIFT INFORMATION (ONT.) See Item VERTIAL SEAM onstruction No. 6 January 0, 00 Uplift - lass 90 or 60 Fire Not Investigated (See Item No.). Metal Roof Deck Panels* 0.0 in. thick aluminum or No. MSG min thickness coated steel. Panels 0-/ in. wide, -/ in. high at the ribs. Panels continuous over two or more spans. A bead of sealant may be used at panel side joints. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners* (Panel lips) One piece assembly, -/8 in. wide, -7/8 in. high. One panel clip located at each purlin intersection. Min thickness 0.08 in. (No. 8 MSG). METAL SALES MFG ORP - Vertical Seam lip. Panel Fasteners (Screws) Fasteners used to attach panel clips (Item ) to purlins to be No. 0-6 by in. long, cadmium plated, pancake head, No. phillips drive, No. self-drilling point. Two screws per clip to be used inserted through / in. diam guide hole in clip base.. Purlins No. 6 MSG min thickness steel (50,000 psi min yield strength). Spacing: For aluminum panels: For lass 90 to be 6 in. O.For lass 60 to be 8 in. O.For steel panels: MSG thick to be 60 in. O. MSG thick to be 8 in. O. Refer to General information, Roof Deck onstructions (Roofing Materials and Systems Directory) for items not evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-8
UL 580 WIND UPLIFT INFORMATION (ONT.) a 6 6 5 5 VERTIAL SEAM onstruction No. 0 January 0, 00 Uplift - lass 90 Fire Not Investigated. Metal Roof Deck Panels* No. MSG min thickness coated steel. Panel width 8 in. max., 0 in. min. ribs height -/ in. at female side. Panels continuous over three or more clips with no end laps. A bead of sealant may be used at panel side joints. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners* (Panel lips) One piece assembly, No. MSG min thickness, -/ in. wide, -5/6 in. high. lip spacing to be 8 in. O. lips to interface with Item A (bearing plate). METAL SALES MFG ORP - Vertical Seam lip A. Roof Deck Fasteners* (Bearing Plate) One piece assembly, No. MSG min thickness steel, -/ in. wide, 6 in. long. D. Bearing Plate (Not Shown) - To be used with Vertical Seam lip only (Item ) - Flat plate, -/ in. wide, 6 in. long fabricated from No. MSG coated steel. Two / in. diam guide holes located to accommodate panel clip screw fasteners. (,000 psi min yield strength).. Panel Fasteners - (Screws) Fasteners used to attach panel clips and bearing plates (Items & A) through rigid insulation and optional OSB and/or gypsum board and into light gauge steel deck (Item No. 5) to be No. truss head type with No. Phillips drive, self-drilling steel screws. Two screws per clip to be used, inserted through / in. diam guide holes. Fasteners to penetrate liner panel / in. min.. Foamed Plastic - (Rigid Insulation) Min thickness in., max thickness -/ in. Density to be a min of pcf. A. Oriented Strand Board (OSB) (Optional) - (Not Shown) - Located over foamed plastic (Item ). Max thickness 7/6 in. Note: Bearing plates not required when OSB is used. B. Gypsum Board (Optional) - Max thickness 5/8 in. Located over liner panel (Item 5). 5. Liner Panel Min thickness No. MSG. oated steel (000 psi) min yield strength min depth -/ in., max pitch 6 in. fabricated to various profiles. 6. Underlayment (Not shown) - One ply of 0 lb roofing felt or one layer of bituminous resin type water proofing membrane. Refer to General information, Roof Deck onstructions (Roofing Materials and Systems Directory) for items not evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-9
UL 580 WIND UPLIFT INFORMATION (ONT.) 7 6 7a 6 8 9 8a 9 8 VERTIAL SEAM onstruction No. October 6, 00 Uplift - lass 90 Fire Not Investigated. Metal Roof Deck Panels* No. MSG min gauge coated steel. Panel width 8 in. max., 0 in. min. Rib height -/ in. at female side. A bead of sealant may be used at panel side joints. Panels continuous over three or more clips with no end laps. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners* (Panel lips) One piece assembly, No. MSG min thickness, -/ in. wide, -5/6 in. high. lip spacing to be 8 in. O. METAL SALES MFG ORP - Vertical Seam lip. Gypsum Board* (Mineral Board) Min thickness / in. Opposite side edges have a tongue and groove configuration. Butt (end) joints to be staggered and occur over steel deck crests. Wallboard installed perpendicular to steel deck corrugations. LOADMASTER SYSTEMS IN. Vapor Barrier (Optional) Installed on top of metal deck (Item 8) or on top of gypsum wallboard (Item ). Minimum 6 mil plastic sheet. 5. Joint Tape (Not Shown) All wallboard joints shall be taped with.5 in. wide joint tape supplied by the manufacturer. 6. Foamed Plastic - (Rigid Insulation) (Optional) - Expanded polystyrene supplied in by 8 ft sheets, min thickness /6 in., min density.0 pcf, or (Rigid Insulation) Polyisocyanurate supplied in by 8 ft sheets or (Rigid Insulation) Phenolic supplied in by 8 ft sheets. All end joints to be staggered with respect to adjoining rows. All joints to be offset from joints in mineral board (Item ). 7. Fasteners For attaching panel clips to steel deck to be two 0.0 in. diam threaded shank Phillips, bugle or trumpet head, self-drilling, self-tapping corrosion resistant coated steel screws supplied by roof deck manufacturer. Screws shall penetrate steel deck min / in. 7A. Fasteners For attaching wallboard to steel deck (Item 8) to be min 0.0 in. diam threaded shank Phillips, bugle or trumpet head, self-drilling, self-tapping, corrosion resistant coated steel screws supplied by the manufacturer. Screws are installed into top corrugations of steel deck through nom by in. corrosion resistant steel roof deck plates, spaced in a pattern as determined by the pitch of the steel deck with the min density of fasteners per by 8 ft sheet (Item ). 8. Steel Deck Fabricated to various profiles, min yield strength,000 psi. Steel deck profile, thickness, support spacing and method of positioning (end and side laps) and fastening deck to supports to be per deck manufacturers requirements for uplift loading. 8A. Deck Fasteners Steel deck panels to be fastened to structural supports and at laps using AR spot welds with weld washers or screw fasteners per deck manufacturer s requirements for uplift loading. 9. Purlins 6 MSG min gauge steel (min yield strength 50,000 PSI) or min Type H open web joists. Refer to General information, Roof Deck onstructions (Roofing Materials and Systems Directory) for items not evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-0
UL 580 WIND UPLIFT INFORMATION (ONT.) 5 5 VERTIAL SEAM onstruction No. December 07, 00 Uplift - lass 90 Fire Not Investigated. Metal Roof Deck Panels* No. MSG min coated steel. Panel width 8 in. max., 0 in. min. Rib height -/ in. at female side. Panels continuous over three or more clips with no endlaps. A bead of sealant may be used at panel side joints. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners*(Panel lips) One piece assembly, -/ in. wide, -7/8 in. high. Min thickness No. 8 MSG. lips spaced 6 in. O, max, fastened to plywood deck. METAL SALES MFG ORP - Vertical Seam lip. Fasteners (Screws) Fasteners used to attach panel clips (Item ) to plywood to be No. 0- by in. long pancake head, No. Phillips drive, A-point, coated steel screw. Min two fasteners per clip to be used.. Underlayment Underlayment used over plywood deck to be Type 5 or 0 organic felt. Sides overlapped min in., end laps per manufacturer s instructions. Felt nailed to plywood deck with -/ in. long steel cap nails, located per manufacturer s instructions. Nail spacing to be max in. O at the side lap and max in. O in interior rows.as An Alternate A self-adhering modified bitumen water proofing membrane may be used, installed per manufacturer s instructions. Note - when alternate is used the plywood joints need not be sealed. 5. Plywood Decking Plywood decking to be graded per PS8 specifications, 9/ in. thick, exposure, APA Rated Sheathing (/0) square edged. Butt ends not blocked. All butt and side joints to be sealed with a one part urethane caulk sealant applied with a caulking gun and feathered outward from the joint. (Note exception under Item No., Alternate.) 6. Supports (Not Shown)-Spaced max of in. O. Any of the following types may be used to support the plywood decking: a) Nom by 6 in., No. grade or better S-P-F, Hemlock Fir, Douglas Fir or Southern Yellow Pine or equivalent. b) Wood trusses with a nom by in. upper chord of the same grade as item a. c) No. MSG min cold formed coated steel (min yield to be,000 psi). 7. Plywood Fasteners (Not Shown)-Fasteners used to attach the plywood deck to the supports to be as follows: a) For plywood-to-wood supports No. 8-8 by -7/8 in. long bugle-head steel screws with a No. Phillips drive, a Hi-Low thread pattern and an S-Point. b) As an alternate to Item a, 8d common nails may be used. c) For plywood-to-steel supports for a steel thickness less than No. 0 MSG No. 7-9 by -/ in. long bugle-head steel screws with a No. Phillips head drive Hi-Low threads and an S-Point. For a steel thickness greater than No. 0 MSG to No. 6 MSG, No. 6-0 by -/ in. long bugle-head steel screws with a No. Phillips drive and a S (TEKS/)supR point. Spacing: Fastener spacing for all fastener types to be 6 in. O at the plywood edges and in. O in the interior. Refer to General information, Roof Deck onstruction (Building Materials Directory) for items not evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-
UL 580 WIND UPLIFT INFORMATION (ONT.) 6 5 " Maximum VERTIAL SEAM onstruction No. 6 February 7, 00 Uplift - lass 90 Fire Not Investigated. Metal Roof Deck Panels* No. MSG min coated steel. Max panel width 8 in., rib height -/ in. Panels continuous over two or more spans. Endlap for panels to be overlapped 6 in. A bead of sealant may be used at panel ends and side joints. METAL SALES MFG ORP - Vertical Seam. Roof Deck Fasteners* - (Panel lips) One piece assembly, -/ in. wide by -7/8 in high. lip spacing to be 8 in. O. METAL SALES MFG ORP - Vertical Seam lip. Fasteners - (Screws) Screws used to attach the panel clips to Substructure (Item ) to be No. 0 by in long Pancake head wood screws with a No. Phillips head or 0x in., / in. Hex Head Woodgrip. Two screws per clip. Screws used to attach Substructure (Item ) to wood trusses or joists (Item 6) to be No. 8 by in. Bugle head screws. As an optional fastener, -/ in. long 8d common deformed shank nails may be used. Fasteners used at endlaps to be x in. Type AB or 0x in. woodgrip. When light gauge structural steel joists are used, screws to be No. by -5/8 in. long with a Phillips head. Spacing of screws to be 6 in. O at plywood or OSB ends and in. O at interior joists.. Substructure (Plywood or OSB) Plywood decking or oriented strand board (OSB) to be a nom 5/8 in. thick, exposure sheathing span -D, 0/0 plywood. (All butt joints to be sealed against leakage by using tape and/or caulking). In lieu of plywood, in. tongue and groove decking may be used. 5. Moisture Barrier - (Optional) Any suitable membrane to protect Substructure (Item ). 6. Joists Joists, spaced at ft, 0 in. O max (when tongue and groove decking is used, joist spacing may be 0 in. O max), may be one of the following: A. Nom by 6 in. wood joists, No. or better. B. Nom by in wood when used on a top chord of a wood truss, No. or better.. Light gauge structural steel framing with the member against the plywood to be a min No. MSG coated steel. Refer to General Information, Roof Deck onstructions, for Items Not Evaluated. *Bearing the UL lassification Mark U L Underwriters Laboratories Inc. LISTED PVS-
UL FIRE RESISTANE RATINGS Metal Roof Deck Panels Metal Sales Manufacturing orporation has obtained fire resistance ratings for various products conducted according to test criteria set forth by 'Underwriters Laboratories' "Standard Fire Tests of Building onstruction and Material" (ANSI/UL 6). This test procedure is identical to ASTM E-9 and NFPA 5. The fire resistance rating is for the total assembly and not just the external metal panel. Ratings are expressed in hours and vary depending upon the assemblies. In general, the test criteria is to evaluate the assembly's ability to continue to support the superimposed loads and resist the passage of flame, high temperatures, or hot gases which will ignite combustible materials. The test assemblies are identified by an alpha-numeric design number. For detail information on specific assemblies and hourly ratings see UL Fire Resistance Directory. METAL SALES MFG ORP R9697 Mechanically attached metal roof panels - Type Vertical Seam secured by steel anchor clips. Anchor clips are attached to a hat shaped member* (minimum depth in.) or a bearing plate**. For use in Design Nos. P, P5, P7, P0, P7, P508, P50, P5, P70, P7, P7, P7, P75, P77, P70, P7, P7, P7, P76, P7, P7, P76, P80, P8, P85, P88, P89, P8, P8, P8. *Hat shaped member to be a minimum of 6 gauge. The member will be fastened through the roof insulation to the steel roof deck with min. No. self-drilling and/or self-tapping fasteners. Spacing to be determined by the structural loading requirements. In addition any compressible UL lassified glass fiber blanket insulation with or without a vapor retarder facing may be used between the specified roof insulation and the metal roof panels. **Bearing plate to be a minimum of 6 gauge. Member will be fastened through the roof insulation to the steel deck with min. No. self-drilling and/or self-tapping fasteners. See the UL Fire Resistance Directory for explanation of each design number listed above. U L Underwriters Laboratories Inc. LISTED PVS-
SETION PROPERTIES AND LOAD TABLES Factory Applied Sealant /" ",6", or 8" overage GAUGE WIDT H (in) YEILD KSI VERTIAL SEAM SETION PROPERTIES WEIGHT PSF Ixx in /f t.. T OP IN OMPRESSION B OTTOM IN OMPRESSIO N " 50. 8. 5 8. 08 0.. 05. 055 7.6 7 6 " 50. 5. 090 8. 060 8.8. 09 8. 0 9. 5 8 " 50.. 08 0. 05 9.6. 05. 07. Sxx in /f t Ma (k-in) Ixx in /f t Sxx in /f t Ma (k-in) ALLOWABLE UNIFORM LIVE LOADS PSF... or more- Equal Spans Inward (Gravity / Deflection) Load.. Outward Uplift (Stress) Load. GA. Width Ksi.5.5.5 5.5.5.5 5 50 99 0 0 80 6 5 70 57 89 5 9 6 50 50 05 78 60 8 9 78 9 09 86 70 8 50 9 69 5 6 7 6 97 76 6. Theoretical section properties have been calculated per AISI 996. Specifications for the design of cold formed steel members. Ixx and Sxx are effective section proper ties for deflection and bending.. Tabulated gravity loads are allowable loads calculated in accordance with AISI 996 specifications considering, bending, shear, and combine stresses. (ombined bending and web crippling is omitted per AISI section.5). Gravity Load considers worst of and multiple equal span condition. Panel weight has not been accounted for in gravity load tables. Allowable loads do not address web crippling requirement or fastener/support connection.. Allowable wind uplift loads have been increased by /% and are based on AISI 996 specifications for the Design of old Formed Steel Members. Note: During uplift or suction condition, panel flat will deflect due to upward load changing shape and reducing these loads. ontact Metal Sales Technical Services for ASTM E-59 uplift design loads.. Deflection consideration is limited by a maximum deflection ratio of L/80 of span. PVS-
DESIGN / INSTALLATION ONSIDERATIONS FASTENER INSTALLATION TEHNIQUE Recommended Tool Type - Use depth locating nose or adjustable clutch on screw gun to prevent overdrilling and strip out. Do not use impact tools or runners. Seating the washer - Apply sufficient torque to seat the washer - do not overdrive the fastener. ORRET Sealing material slightly visible at edge of metal washer. Assembly is watertight. TOO LOOSE Sealing material is not visible; not enough compression to seal properly. TOO TIGHT Metal washer deformed; sealing material pressed beyond washer edge. WOODSREW SELF DRILLER To prevent wobbling - Make sure fastener head is completely engaged in the socket. If the head does not go all the way in the socket - tap the magnet deeper into the socket to allow full head engagement. Metal chips will build up from drilling and should be removed from time to time. Protect drill point - Push only hard enough on the screw gun to engage clutch. This prevents excess friction and burn out of the drill point. orrect pressure will allow screw to drill and tap without binding. Drilling through sheet and insulation - Ease up on pressure when drilling through insulation to avoid striking the purlin or girt with the point - apply more pressure after drill point contacts purlin or girt. Drilling through purlin overlaps - Drilling through lapped purlins requires extra care. Excessive voids between purlins sometimes damages drill points and two self-drillers might be necessary to complete the operation. It is sometimes advantageous to predrill. ONDITION OF SUBSTRUTURE Whether over solid substrate or open structural framing, panel distortion may occur if not applied over properly aligned and uniform substructure. The installer should check the roof deck for squareness before installing Vertical Seam panels. Several methods can be used to verify squareness of the structure for proper installation of the panels. METHOD "A" - One method for checking the roof for squareness is to measure diagonally across one slope of the roof from similar points at the ridge and eave and obtain the same dimension. METHOD "B" - The --5 triangle system may also be used. To use this system measure a point from the corner along the edge of the roof at a module of three (). Measure a point from the same corner along another edge at a module of four (). Then by measuring diagonally between the two points established, the dimension should be exactly a module of five (5) to have a square corner. Multiple uses of this system may be required to determine building squareness. If the endwall cannot be made square, the roof system cannot be installed as shown in these instructions. Method A 0 0 5 Method B PVS-5
DESIGN / INSTALLATION ONSIDERATIONS (ONT) VENTILATION Proper design and installation of vapor barriers and ventilation systems are important to prevent condensation and the resulting problems of moisture damage and loss of insulation efficiency. ondensation occurs when moisture laden air comes in contact with a surface temperature equal to or below the dew point of the air. This phenomenon creates problems that are not unique with metal buildings; these problems are common to all types of construction. The underside of the metal roof on a typical metal building (no attic) should be protected from condensation by insulating with a faced insulation. This should reduce the potential of condensation forming on the underside of the panels. On buildings that have an attic space or are being retrofitted with a metal roofing system, vents should be placed at both the eave and peak of the roof in order to prevent a buildup of moisture (humidity) in the attic space. Vent Vent Insulation Vent at Wall Typical Metal Building (No Attic) Vent at Eave Building with Attic or Retrofitted INSULATION Insulation is recommended on all applications to act as a sound barrier, prevent condensation, and increase insulating value of the roof or ceiling system. Typically, panels are installed over solid substrate but can be installed over open framing or metal decking (shown below) with many different types of insulation. Blanket, rigid, and reflective insulation are just a few. Maximum thickness for blanket insulation is three inches. Please contact your insulation supplier for specific recommendations on type of insulation, vapor barriers, and installation procedures. Vertical Seam lip Blanket Insulation Vertical Seam panel Rigid Insulation /" Maximum (Per UL Listing) Metal Decking Bearing Plate AUTION Use extreme care when working next to insulation. The insulation will provide a false sense of security by hiding the view of the ground below the insulation. PVS-6
DESIGN / INSTALLATION ONSIDERATIONS (ONT) SYSTEM EXPANSION / ONTRATION Steel roofing panels are subject to dimensional changes after installation due to exposure to varying temperatures. The greatest influence is solar energy. Steel roofing absorbs various amounts of heat depending upon color, finish, angle of exposure, and time of exposure. The relationship of ambient temperature to building structural temperature must be considered when designing a Vertical Seam roof system. The floating clips for the Vertical Seam panels are designed for expansion and contraction of the panels in the longitudinal direction. Lateral expansion and contraction is accommodated by the configuration of the panel cross section and causes negligible panel movement. When the total length of panel run exceeds the capability of the clips to accommodate the thermal movement, expansion joints must be designed into the structure. SELETION OF SYSTEM OMPONENTS Vertical Seam panel clips - lips are placed along the male leg of each panel prior to installing adjacent panels. Design wind uplift must be considered for proper clip spacing. Vertical Seam lip Vertical Seam UL-90 lip ( fasteners required) The following chart should be used to determine proper fasteners required for clip installation on the selected applications. (See Fastener Selection Guide page 6 for other fasteners available.) APPLIATION LIPS OVER PURLINS (6 GA. MIN) INSTALLATION REQUIREMENTS UL-90 UL-90 UL-90 GAUGE GAUGE **LIP SPAING '-0" O.. '-0" O.. GAUGE 5'-0" O..*** TYPE OF FASTENER #0 X " PANAKE HEAD DRILLER #0 X " PANAKE HEAD DRILLER #0 X " PANAKE HEAD DRILLER # REQ. FASTENERS FASTENERS FASTENERS LIPS OVER 5 /8" WOOD DEK UL-90 UL-90 GAUGE GAUGE '-0" O.. '-0" O.. #0 X " PANAKE HEAD WOOD #0 X " PANAKE HEAD WOOD FASTENERS FASTENERS Max suction pressure of psf LIP OVER RIGID INSULATION / METAL DEK Standard clip Standard clip UL-90 UL-90 GAUGE GAUGE GAUGE GAUGE '-6" O.. '-6" O.. '-0" O.. '-0" O.. #0 X " PANAKE HEAD WOOD #0 X " PANAKE HEAD WOOD DEKFAST #* DEKFAST #* * Length of Dekfast will vary depending on the total thickness of the rigid insulation and metal. ** ontact your local Metal Sales branch representative for more information (see pages and ). *** " Panel Only FASTENER FASTENER FASTENERS FASTENERS Bearing Plate (Flat) PVS-7
EAVE DETAIL : SLOPE MINIMUM Vertical Seam Panel Tube Sealant #- x /" Self Driller XL (see below) Double Bead Tape Sealant Eave leat #0-6 x " PHD ("o.c.) AUTION Additional screws may be required for high snow loading and steep slopes. PVS-8 Vertical Seam Fastening Pattern
EXTENDED EAVE DETAIL : SLOPE MINIMUM Vertical Seam Panel Tube Sealant #- x /" Self Driller XL (see below) Double Bead Tape Sealant Extended Eave leat #0-6 x " PHD ("o.c.) AUTION Additional screws may be required for high snow loading and steep slopes. Vertical Seam Fastening Pattern VERTIAL SEAM BOX GUTTER DETAIL : SLOPE MINIMUM Vertical Seam Panel Tube Sealant #- x /" Self Driller XL (see below) Double Bead Tape Sealant Universal Gutter/ D.S. Strap ('-0" o.c.) /8" x /6" Pop Rivet (every strap) Box Gutter AUTION In locations where heavy rainfall or severe ice and snow may occur, Metal Sales' standard gutters may not be suitable for use. Vertical Seam Fastening Pattern PVS-9
VALLEY DETAIL : SLOPE MINIMUM Vertical Seam Panel Vertical Seam lip Double Bead Tape Sealant #- x /" Self Driller XL (see below) Tube Sealant Valley Valley Plate " Min. L AUTION Additional screws may be required for high snow loading and steep slopes. Vertical Seam Fastening Pattern PVS-0
RAKE (ON MODULE) DETAIL Vertical Seam Panel /8" x /6" Pop Rivet ('-0" o.c.) Double Bead Tape Sealant Rake leat Rake #- x /" Self Driller XL ('-0" o.c.) Floating Rake Angle #- x /" Shoulder SD ('-0" o.c.) Rake Angle leat #0-6 x " PHD ('-0" o.c.) PVS-
RAKE (OFF MODULE) DETAIL Vertical Seam Panel /8" x /6" Pop Rivet ('-0" o.c.) Double Bead Tape Sealant Rake leat Rake #- x /" Self Driller XL ('-0" o.c.) Floating Rake Angle #- x /" Shoulder SD ('-0" o.c.) Rake Angle leat #0-6 x " PHD ('-0" o.c.) PVS-
: SLOPE MINIMUM RAKE PARAPET (ON MODULE) DETAIL Tube Sealant ounter Flashing Fastener (by others) Rakewall #- x /" SD XL ("o.c.) /8 x /6" Pop Rivet ("o.c.) Double Bead Tape Sealant Rake leat #- x /" Shoulder SD ("o.c.) Floating Rake Angle Vertical Seam Panel VERTIAL SEAM : SLOPE MINIMUM RAKE PARAPET (OFF MODULE) DETAIL Tube Sealant ounter Flashing Fastener (by others) Rakewall /8 x /6" Pop Rivet ("o.c.) Double Bead Tape Sealant Rake leat #- x /" SD XL ("o.c.) #- x /" Shoulder SD ("o.c.) Floating Rake Angle Vertical Seam Panel Field bend panel rib up /" PVS-
: SLOPE MINIMUM SSR RIDGE/HIP DETAIL Vertical Seam lip Vertical Seam Panel /8" x /6" Pop Rivet (see below) Double Bead Tape Sealant Tube Sealant Vertical Seam Z-losure #0-6 x " PHD ( Per Panel) Double Bead Tape Sealant SSR Ridge/Hip over Back-Up hannel " L Flashing Pop Rivet Z-losure Tape Sealant Gun Grade Sealant PVS-
: SLOPE MINIMUM VENTED RIDGE DETAIL Vertical Seam Panel Vertical Seam lip /8" x /6" Pop Rivet ('-0" o.c.) Double Bead Tape Sealant Offset leat #- x 5 /8" Dekfast ('-0" o.c.) Vent Material Tube Sealant #0-6 x " PHD ( per panel) Double Bead Tape Sealant Back-Up hannel Vented Ridge over Vent Drip Note: Refer to PSL-6 for proper ventilation considerations. Flashing Pop Rivet Z-losure Tape Sealant Gun Grade Sealant VERTIAL SEAM : SLOPE MINIMUM AUTION Additional screws may be required for high snow loading and steep slopes. HIGHSIDE PARAPET DETAIL Tube Sealant Fastener (by others) ounter Flashing Pitch Break Back-Up hannel #0-6 x " PHD ( per panel) Tube Sealant Double Bead Tape Sealant /8" x /6" Pop Rivet (see below) Vertical Seam Z-losure Vertical Seam Panel Flashing Pop Rivet Z-losure Tape Sealant Gun Grade Sealant PVS-5
NOTES PVS-6