ET4 The measuring unit consists of a glass table and a tele-centric lens framed in aluminium profiles and painted guards, RAL 7035. The overall dimensions are: 420 x 840 x H2000 mm.the operator places the part to measure on the glass table, the camera (matrix 2000x2000) together with the telecentric lens acquires the image without distortion. The collected data can be accessed by the operator through the graphic interface. These data are saved in a database and are available for the operator at any time. Type of check - Ring Min.and Max ID Min.and Max OD Max difference between the max and the min ID Min. Max. Chord Average ID Average OD Average Chord Multiple measurement (it allows to measure more parts within the framed field by comparing them with the set average tolerances). Type of check - Irregular shape Four adjustable rulers (identified with the auto-learning) for the measurement of linear distances on the part's shape. Automatic definition of the measurement point (by means of a dedicated software) which allows obtaing orthogonal measurements (even of non parallell profiles). Partial curving rays, distance between the centers, ID. Part's data saving for following consecutive measurements without need to orient the part. Comparison with the tolerances (five positive and five negative (or at zero) with respect to the nominal value) Saving of the obtained values in a chart with CP and CPK calculation Framed field: Min. diameter measurable part: Part's thickness (Z): Max. diameter measurable part: Elaboration time: Measure repeatability Measure accuracy Single-phase power supply: Use temperature: Relative humidity: Electrical safety protection: Installed power supply: ET4 130x130mm 124 mm 1 mm 0,1-30 mm 1 pc/sec. ± 0,013 mm ± 0,027 mm < 15 db 230V - 50Hz +5 C to +40 C max 80% IP 44 4 kw 1,5 Kw
MIGG & MIGG1500 Automatic measuring system without contact for circular parts, deformed as well, with Laser techology. Instrument accuracy according to DIN 3771. Calibrated sample ring for the machine adjustment (with calibration certificate- not a SIT one). Type of check Article file: each article code is complete with description and relative tolerances. By re-calling of an existing code, all the data relative to this article are displayed on the main page. The results are shown in different colors: green= piece within tolerance, red= piece out of tolerance Acoustic alarm to signal that the part is out of tolerance. MIGG MIGG1500 Min. ID Max. OD Max. piece weight Repeatability Accuracy Circumference scan - low speed Circumference scan - high speed Single-phase power supply: Max. installed power supply: 10 mm 250 mm 450 mm 1500 mm 0.8 Kg 4 kg ± 15 µm (1) ± 100 µm (2) ± 30 µm (1) ± 100 µm (2) 15 sec. 60 sec. 5 sec. 20 sec. 115/230 V 115/230 V 0,5 kw 0,8 kw (1) With metallic gauge: chord 10 mm and diameter 150 mm, max. disalignement 5 mm, low speed. (2) With metallic gauge: chord 10 mm and diameter 370 mm, max. disalignement 5 mm, high speed.
Densimetro The system allows to measure the density of solid bodies in elastomeric material. The device works on the principle of the weight measure, of the volume determination through the thrust received by the body in the liquid and the correction due to the liquid temperature. The device is composed of an electronic scale (accuracy 0,001 g), an automatic piece handling system and an external keyboard. Through the data interface, the values are displayed on both keyboard and PC and elaborated in a dedicated database. Type of check Density - specific weght Weight delta Volume delta Sample max. weight Sample max volume Beaker dimensions Typical cycle (5 read. Air + 5 read. Water) Measure repeatability Linearity Single-phase power supply: Use temperature: Relative humdity: Electrical safety protection: Installed max. power: Densimetro 120 g 100 cc 500ml x ø80mm 30 sec e= 0,01 g +/- 0,002 < 40 db 230V - 50Hz +5 C to +40 C max 80% IP 44 0,1 kw 0,02 Kw
Spess Instrument for the thickness measuring. It can be programmed to check different thickness with a double tolerance (+ or - xxx) The machine structure is made of aluminum while the plane, where the laser heads are positioned, is made of steel. Parts are loaded manually by the operator onto an antiscratch belt. The software recognizes the profile while the parts pass under the laser heads.the result displayed is a line representing the profile as if the analyzed parts were cut. The system calculates the measures and displays them according to the data previously set in the system and in the respect of the tolerances. Type of check The type of measures that can be displayed: 10 different thickness measures possible. Recording of the measured sets. Check of each measure with double tolerance (plus & minus) Recording of each measure in a table for CP & CPK calculations. Max. Framed field Min part s thickness Max part s thickness Repeatability Accuracy Elaboration time: Single-phase power supply Max. installed power Electrical safety protection Noise rate Use temperature Relative humidity Signalling device The software shows different menus for the following functions: set up of the parameters for image resolution and optimization. Selection of the type of measurement Spess 80x100mm 0,2 mm 20mm ± 0,01 mm ± 0,02 mm 5 sec. Max 230 V 500 w IP44 < 15 db +5 C to +40 C max 80% 2 colors lamp
Mistral Automatic sorting machine.the pieces will be loaded in a bulk and then separated, in different bins, into good parts (iin the tolerance range) and scraps, at the end of each inspection cycle. The operator sets the machine with the parameters and the tolerances required and as a result, he obtains a complete report of the good parts, the scrap details and the counting for each type. This machine is available in two versions: Automatic: lenses and feeding system are completely motorized (motors with encoders). The machine can be set automatically in few seconds. Manual: manual optimization of the zoom and aperture as well as of the feeding system. The estimated time for this operation is 15'. The machine guarantees a perfect repeatability of the checks and traceability of the inspected batches. Option: Both versions (automatic and manual) can be equipped, even later, with a single periferico unit for the inspection of the border's surface and with packaging and labelling machine. Type of check - Digital camera One side surface inspection Check flash, lack of material and remolded. Cuts Dimension Different color Porosity Certificate Non circolarity Concentricity Piece counting Statistics Type of check - Laser Planarity Thickness Type of check - Periferico (option) Scratches on the closing line Cuts Lack of material Max. piece's dimension (ext.): Max. piece's height: Pieces/sec.: Zoom: Resolution Wide: Resolution tele: Measurement repeatability (wide mode) Measurement repeatability (tele mode) Measurement accuracy min/max T/W Three-phase power supply: Max. installed power: Manual Automatic 50mm 50mm 0,8-15 mm 0,8-15 mm 8 pc/sec.(1) 8 pc/sec.(1) 6x manual 6x automatic 78 µm/px 78 µm/px 26 µm/px 26 µm/px ± 20 µm (2) ± 20 µm (2) ± 5 µm (2) ± 5 µm (2) ±10/±40 µm ±10/±40 µm < 76,5 db < 76,5 db 400/440 V (3) 400/440 V (3) 4 kw 4 kw 1,5 Kw 1,5 Kw 650 NL/min 650 NL/min (1) For parts with outside diameter smaller than 10 mm - (2) Test done with a stable part on a glass table, at low speed, on the dimensional station. - (3) Tension 440V only 60 Hz
Lite D Automatic sorting system composed of two tables which enable the pieces to be checked on both sides. The pieces will be loaded in a bulk and then separated in different bins, into good parts (in the tolerance range) and scraps, at the end of each inspection cycle. The operator sets the machine with the parameters and the tolerances required and as a result, he obtains a complete report of the good parts, the scrap details and the counting for each type. The machine guarantees a perfect repeatability of the checks and traceability of the inspected batches. Option Additional Periferico unit Packaging and labelling machine for the inspected and counted parts (in bags). Type of check - Camera 1/Camera 2 Surface inspection side A Surface inspection side B Color identification Cuts Scratches Inclusions Haloes Piece counting Statistics Certificate Type of check - Camera 2 Dimensional check: up to 4 measurements per piece Profile check (contour) Check flash, lack of material and remolded Concentricity Ovalization Piece counting Statistics Certificate Type of check - Laser Planarity Thickness Type of piece: Color of the piece: Characteristic of the piece: Inspection area: Max framed field: Max.piece's height: Pieces/sec.: Zoom: Measurement repeatability in wide: Measure repeatability in tele: Measurement accuracy min/max T/W: Three phase power supply: Max installed power: LITE D LITE D M LITE D HD LITE D HD M elastomers,rigid materials all, non transparent clean, free of dust or particles that may alter the part's profile manual - automatic 55 mm 90 mm 55 mm 85 mm 0,8-15 mm 0,8-15 mm 0,8-15 mm 0,8-15 mm 8 pc/sec.(1) 8 pc/sec.(1) 8 pz/sec.(1) 8 pz/sec.(1) 6x man/aut 6x man/aut 6x man/aut 6x man/aut ± 39 µm (2) ± 130 µm (2) ± 12 µm (2) ± 20 µm (2) ± 13 µm (2) ± 21 µm (2) ± 2 µm (2) ± 5 µm (2) ±26/±78 µm ±21/±130µm ±4/±24 µm ±10/±40 µm < 75 db < 75 db < 75 db < 75 db 1,7 Kw 1,7 Kw 2,2 Kw 2,2 Kw 230/400/440 V (3) 230/400/440 V (3) 230/400/440 V (3) 230/400/440 V (3) 6 kw 6 kw 6 kw 6 kw 800 NL/min 800 NL/min 800 NL/min 800 NL/min (1) For parts with outside diameter smaller than 10 mm - (2) Test done with a stable part on a glass table, at low speed, on the dimensional station - (3) With 440V only 60 Hz
Ispegg Automatic sorting machine for big gaskets, composed of 6 inspection stations. The feeding unit conveys the pieces, one by one, on the handling system which carries them to the "Pick&Place" device. This will load one piece at a time onto the checking stations. Two pulleys, one of which is motorized, will put the piece in rotation. Each camera inspects one portion of the piece thus guaranteeing the check on the whole surface. The operator chooses the parameters and the tolerances to follow and he obtains, as a result, a complete report of the good parts. The machine guarantees a perfect repeatability of the checks and traceability of the inspected batches. Options Possibility of an additional station for the dimensional checks. Type of check - complete surface inspection Inclusions Stains Haloes Lack of material Scratches Tears Cuts Flashes Different colour Dimensional Type of pieces: Min. internal diameter: Max external diameter: Min. Chord: Max. Chord: Resolution: Max. inspection speed: Three-phase power supply: Max. installed power: Type 1 Type 2 Elastomers Elastomers 60 mm 100 mm 180 mm 250 mm 2 mm 2 mm 6 mm 6 mm 0,025 mm/pixel 0,025 mm/pixel 1000 pz/h (1)(3) 600 pz/h (1)(3) < 70 db < 70 db 400 V (2) 400 V (2) 6 kw 6 kw 800 NL/min 800 NL/min (1) For parts with OD smaller than 100mm/150mm (2) Tension 440V only 60 Hz (3) Pieces with pace feeding
Migl II Sorting machine for irregular gaskets with manual load. Parts need to be clean, free of dust and/or particle which can alter the shape/profile, otherwise they will be rejected. Type of check Station 1 Surface check side A (first side): Scratches Porosity Type of check Station 2 Turnover system Surface check side B (second side): Scratches Porosity Type of check - Station 3 Four linear measurements to be acquired by means of 8 rulers. Check internal/external flashes Check breaks that may alter the piece profile Check batch assignement Broken parts Piece dimensions: width Piece dimensions: length Piece dimenisons: thickness Resolution: Type of pieces: Color of pieces: Inspection speed: Inspection area: Migl II 30-190 mm 30 190 mm 1-10 mm 0,045 mm/pixel elastomers rigid mat. all, non transparent 15 mt/min < 70 db (A) fix, manual adj. 9 KW 800 Nl/min
Piri T Automatic sorting system dedicated to oil seals and similar parts. The pieces will be loaded one after the other on the conveyor belt and then separated, in different bins, into good parts (in the tolerance range) and scraps, at the end of each inspection cycle. The operator chooses the area to inspect and the relative parameters for each camera. Type of check Surface inspection ID/OD Cuts Porosity Flow lines Lack of material Tears M1=Inspection of the sealing lip of the oil seal M2=upper surface inspection"check the presence of the spring". M3=Lower surface Inspection check back-ring M4=Outside lateral surface inspection M5=Diameter measurement, check flashes, concentricity, ovalization. Technical Data Sheet Max. optical field: Max. piece's height: PC/second: Zoom: Piece's colour Measurement accuracy with telecentric Three-phase power supply: Necessary power supply: (1) For parts with Ø 100 mm - (2) Power supply 440V only 60 Hz Piri T 200 mm 50 mm 8,5 sec/pc. (1) manual All ± 0,027 mm < 75 db 1,7 Kw 230/400/440 V (3) 10 kw 100 NL/min
DIM Automatic sorting machine for diaphragms and similar parts. It consists in 5 parallel stations to check the seal. The operator loads the parts manually on a synchronized revolving table with double button. 5 stations will check the loss of pression and they will detect the defected part. Pick&place devices will prepare the parts for the dimensional and surface inspection. At the end of the cycle, a robot will select and unload the rejected parts and will place the good ones into the relative gathering blisters. An additional lung with empty and full blisters complete the supply guaranteeing a longer autonomy. The operator sets the parameters and the tolerances and the machine completes a report relative to the good parts. The machine guarantees a perfect repeatability of the checks and the traceability of the inspected batches. Type of check Leak test (loss of pression) Surface test - upper surface Dimensional test Check flashes and profile deformation Palletizer Robot and blister unload Max. inspection area Single-phase power supply: Use Temperature: Relative humidity: Electrical Protection: Installed power supply: DIM 80x100 mm < 70 db 230V - 50Hz +5 C to +40 C max 80% IP 44 9 kw 650 NL/min