ALSAN RS POCKET INSTRUCTIONS

ALSAN RS POCKET INSTRUCTIONS

ALSAN RS Pocket Guide INDEX SECTIONS PAGE Surface preparation 07 Product information Systems information Application information Details 9

ALSAN RS Pocket Guide TIME TESTED DEPENDABILITY For over 00 years, the SOPREMA GROUP has developed and manufactured cutting edge waterproofing systems for all aspects of the building envelope. Today, advanced PMMA (polymethyl methacrylate) technology found in the ALSAN RS System is revolutionizing the industry by combining liquid with time proven products to deliver unbeatable waterproofing protection. The ALSAN RS System is the ideal solution for waterproofing almost any surface including balconies, terraces, water features, flat roof areas, plazas and many more. This ALSAN RS System Pocket Guide has been developed to aid installers by providing detailed system information, optional finishes, proper installation procedures, drawing details and much more. It can be used right on the job site and acts as a quick reference tool promoting a successful installation every time.

ALSAN RS Pocket Guide 6 7 Surface Preparation Product Information Systems Information Application Information Details

Surface preparation GENERAL Prior to application of any Soprema ALSAN RS products or materials, the substrate shall be prepared as recommended by Soprema and required for the intended application. All substrates must be clean, dry and free of oil, grease, curing compounds, release agents, laitance, grass irregularities, loose, unsound or foreign material such as moss, algae growth, dirt, ice, snow, water or any other condition that would be detrimental to adhesion of the primer and/or resin to the substrate. Some surfaces may require scarifying, sandblasting or grinding to achieve a suitable substrate. CONCRETE New concrete must be cured a minimum of 8-days in accordance with ACI-08, or as recommended by the concrete/mortar manufacturer, with a minimum hardness of,00 psi ( mpa). Where required, new or existing concrete shall be abrasively cleaned in accordance with ASTM D 9 to provide a sound substrate free from laitance with an open concrete surface. Concrete surface must be prepared to obtain a concrete surface profile (ICRI CSP) of, or. When using mechanical methods to remove existing waterproofing products or surface deterioration, the surface profile is not to exceed mm (/8-inch) peak to valley. The substrate shall be sounded and all spalls, voids and blow holes on vertical or horizontal surfaces must be repaired before placement of the approved primer coat. Areas of minor surface deterioration of mm (/-inch) or greater in depth shall be repaired to prevent possible pounding, leading to excessive usage of primer and/or resin. MASONRY Walls should be constructed of hard kiln-dried brick, concrete block, or other tilt-up or cast-in-place concrete construction. Masonry walls shall be prepared in the same manner as indicated for concrete substrates. Membrane must not be applied over soft or scaling brick or masonry, faulty mortar joints, or walls with broken, damaged or leaking coping. Walls of ordinary hollow tile, or other materials which in themselves are not waterproofed, should not be accepted as suitable to receive flashings unless they are properly waterproofed, to prevent moisture infiltration from above or behind the flashing system.

ALSAN RS Pocket Guide 8 9 WOOD Wood plank, timber or plywood shall be prepared as required to provide a suitable substrate for proper application of Soprema ALSAN RS materials. Fill joints, knot holes or cracks with ALSAN RS Paste to provide a level substrate. Cover joints in plywood sheathing with -inch (0 cm) wide strips of appropriate ALSAN RS fully reinforced liquid membrane after priming. Plywood sheathing shall meet the requirements of American Plywood Association (APA) product standard PS or better. METAL Clean and prepare metal surfaces to near white metal in accordance with SSPC - SP (power tool clean) or as required by membrane manufacturer. Extend preparation a minimum of 8 cm ( inch) beyond the termination of the membrane flashing materials. Notch steel surfaces to provide a rust-stop. Unless otherwise indicated, all metal surfaces shall be abraded in order to provide a rough open surface. A wire brush finish is not acceptable. Surfaces should be cleaned with ALSAN RS Cleaner or ALSAN All-Purpose Claner prior to system application. MODIFIED BITUMEN MEMBRANE All loose granules, dust and dirt shall be removed from the surface of the builtup roof (BUR) membrane by brooming and/or power vacuuming. FRAME CONSTRUCTION Frame walls are not acceptable to receive ALSAN RS cold fluid-applied reinforced membrane flashings unless suitable solid backing for the flashing is provided. As a minimum, plywood sheathing or cement backer board should be used as wall sheathing. Walls sheathed with gypsum wall board or other gypsum based products are not acceptable as a substrate for cold fluid-applied reinforced membrane. Suitable stops should be provided at the top of the flashing in curtain wall construction, to ensure a watertight seal for flashings.

ALSAN RS Pocket Guide 0 GLASS Glass should be solvent washed and cleaned with Soprema ALSAN RS Cleaner or ALSAN All-Purpose Cleaner to remove all oil, grease, loose particles, algae growth, dirt, bituminous products and previous waterproofing materials to ensure a continuous uniform bond between surfaces. A minimum -inch (0 cm) continuous overlap and bond line of ALSAN RS membrane to glass should be used where a mechanical termination to glass is required. In areas where a watertight joint is required, a -/ inch ( cm) minimum continuous overlap and bond line of ALSAN RS membrane to glass should be used. In all cases, the bond strength should be tested to assure proper adhesion. OTHER SUBSTRATES Remove all contaminants as required. Surface preparation shall be performed by means approved by Soprema. Contact your Soprema representative for preparation and treatment not specifically indicated above. SUBSTRATE LEVELING AND PATCHING Fill cavities and depressions with ALSAN RS Repair Mortar or ALSAN RS Mortar resin on horizontal surfaces or ALSAN RS Paste for all vertical and horizontal substrate repairs as needed to achieve a flat surface. Any surface to be leveled or patched must first be primed with an appropriate ALSAN RS primer when required. CRACKS Determine that crack is not active. Remove any existing filler and clean out crack by brushing and oil-free compressed air. Fill crack with ALSAN RS Paste. Alternately, when approved prior to project start-up, a polyurethane sealant may be used, but must be allowed to completely cure prior to application of ALSAN RS primer or membrane.

Substrate testing Void investigation Tap the surface with a hammer and mark hollow areas. Non-destructive testing for relative humidity of substrate Electronic methods allow for testing of the relative humidity which should not exceed % (by weight) or 6% (by volume). Ground moisture testing Calcium chloride-based moisture measurements are a very accurate gauge for surface moisture testing.

ALSAN RS Pocket Guide Compressive strength study A specialized device is used to examine compressive strength of a substrate. Adhesive strength study The substrate is investigated with a device to determine bond strength. Cementitious substrates: >. mpa Asphalt surfaces: > 0.8 mpa Core study A core drill study can be used to determine the existence of previously installed systems that may impact current system selection. 6

Surface preparation Shot-blasting Shotblasting is the most efficient method for concrete surface preparation over wide open spaces. Laitance and other contaminants are found in the upper layer of finished concrete and will adversely affect adhesive strength. Shot-blasting will remove this layer and smooth the surface while removing dust at the same time. Diamond grinding A handheld grinder with a diamond cup wheel is the easiest way to prepare small areas, as well as vertical walls, upturns and curbs. Removal of abrasive dust through vacuum suction is highly recommended. Milling Particularly with very rough substrates, milling of the surface is recommended. A subsequent shot-blasting will provide an optimal surface for subsequent coatings.

ALSAN RS Pocket Guide Sandblasting Sandblasting is an efficient method for surface preparation of vertical surfaces, but protective measures are necessary. Clean Clean non-absorbent surfaces with a suitable cleaner. Manual Grinding / Buffing... with abrasive discs for metal and other surfaces. The rougher the substrate, the better the adhesion! 6

Surface preparation Manual Grinding / Buffing Using abrasive paper (assuming machine grinding is not possible). Grain size: 0-0. The rougher the substrate, the better the adhesion! Surface Cleaning Remove dust and non-adhesive particles with a vacuum cleaner. 7 Tool Cleaning Tools should be cleaned immediately and thoroughly with ALSAN RS Cleaner or ALSAN All-Purpose Cleaner. 8 9

ALSAN RS Pocket Guide 6 7

Substrate preparation table Surface Preparation Primer CEMENTIOUS SURFACES Concrete Grind with diamond cup wheel or shot blast ALSAN RS 76 Primer Brick Grind with diamond cup wheel or shot blast ALSAN RS 76 Primer Masonry block Grind with diamond cup wheel or shot blast ALSAN RS 76 Primer Mortar Grind with diamond cup wheel or shot blast ALSAN RS 76 Primer RECOVERY BOARDS DensDeck Remove dust and particulates ALSAN RS 76 Primer DensDeck Prime Remove dust and particulates ALSAN RS 76 Primer DensDeck DuraGuard Remove dust and particulates ALSAN RS 76 Primer SECUROCK Roof Board Remove dust and particulates ALSAN RS 76 Primer WOOD PRODUCTS Raw Remove dust and particulates ALSAN RS 76 Primer OSB Remove dust and particulates ALSAN RS 76 Primer Plywood Remove dust and particulates ALSAN RS 76 Primer METAL Copper Clean with ALSAN All-Purpose Cleaner; roughen with abrasive disc or belt sander No primer Aluminum Clean with ALSAN All-Purpose Cleaner; roughen with abrasive disc or belt sander No primer Galvanized steel Clean with ALSAN All-Purpose Cleaner; roughen with abrasive disc or belt sander No primer Zinc Clean with ALSAN All-Purpose Cleaner No primer Stainless steel Clean with ALSAN All-Purpose Cleaner; roughen with abrasive disc or belt sander No primer MEMBRANES (SBS) modified bitumen Remove loose particulates No primer (APP) modified bitumen Remove loose particulates ALSAN RS Primer PVC Remove particulates; clean with ALSAN All-Purpose Cleaner No primer TPO Remove particulates; clean with ALSAN All-Purpose Cleaner No primer EPDM Remove particulates; clean with ALSAN All-Purpose Cleaner No primer MISCELLANEOUS PMMA Remove particulates; clean with ALSAN All-Purpose Cleaner No primer Polyurethane coating Remove particulates; clean with ALSAN All-Purpose Cleaner No primer Rigid PVC pipes and tubes Lightly sand; wipe clean No primer Glass Lightly sand; clean with ALSAN All-Purpose Cleaner No primer

ALSAN RS Pocket Guide 8 9 Notes Laitance must be removed. Laitance must be removed. Laitance must be removed. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. All joints to be stripped in with fabric-reinforced ALSAN RS 0 Flash or ALSAN RS 60 LO Flash must be covered. Do not grind if zinc corrosive protective film is present. Roughen with abrasive disc at least /6 inch (0. mm). Thermofusible plastic film should be burned off prior to liquid application. Liquify surface by application of heat and immediately top with quartz aggregate. Adhesion testing on existing membrane is recommended. Adhesion testing on existing membrane is recommended. Adhesion testing on existing membrane is recommended. Adhesion testing is recommended. Adhesion testing is recommended. Adhesion will not be optimal.

ALSAN RS Pocket Guide 0 Surface Preparation Product Information Systems Information Application Information Details

ALSAN RS Pocket Guide CONTENTS Product information PAGE ALSAN RS Primer 6 ALSAN RS 76 Primer 7 ALSAN RS 0 Field (summer formulation) 8 ALSAN RS 0 Field (winter formulation) 9 ALSAN RS 0 Flash (summer formulation) 0 ALSAN RS 0 Flash (winter formulation) ALSAN RS 60 LO Field ALSAN RS 60 LO Flash ALSAN RS 6 LO Self-Leveling Mortar ALSAN RS 87 Color Finish Base + Color Pack ALSAN RS 89 Textured Base (+ Color Pack or Deco Chips) 6 ALSAN RS Paste 7 ALSAN RS Detailer 8 ALSAN RS Fleece 9 Quartz Aggregate 9 ALSAN RS Catalyst 0 Deco Chips 0

Product information Product ALSAN RS SYSTEM (PMMA) ALSAN RS ALSAN RS 76 ALSAN RS 0 Field ALSAN RS 60 LO Field ALSAN RS 0 Flash ALSAN RS 60 LO Flash ALSAN RS Mortar ALSAN RS 89 Textured Base + Color Pack Additive ALSAN RS 6 LO Mortar ALSAN RS 8 Clear Finish ALSAN RS 87 Color Base ALSAN RS Paste ALSAN RS Detailer Description Primer for asphaltic surfaces Primer for porous surfaces Resin incorporated with fleece reinforcement Low odor resin incorporated with fleece reinforcement Resin incorporated with fleece reinforcement for flashing details Low odor resin incorporated with fleece reinforcement for flashing details Flexible leveling mortar and wearing layer Aggregate infused trafficable surface layer Low odor flexible leveling mortar and wearing layer Clear finish for use with colored quartz aggregate Customizable color finish mixed with color pack additive Flexible resin paste Micro-fiber infused resin paste ALSAN RS 87 Color Finish Base is a clear base resin that is mixed with a pre-selected Color Pack Additive prior to the addition of catalyst activator. Coverage rate over aggregated finish is lower than over smooth surface application. Coverage rate information refers to a generally smooth surface and may vary depending on substrate conditions.

ALSAN RS Pocket Guide Container weight (kg) Coverage per container Coverage rate (per m ) Pot life (at 0 C) Rainproof (at 0 C) Next layer (at 0 C) Fully cured 0 69 0. kg 0 min 0 min 0 min hours 0 69 0. kg 0 min 0 min 0 min hours 90.0 kg min 0 min 60 min hours 90.0 kg 0 min min hours hours.0 kg min 0 min 60 min hours.0 kg 0 min min hours hours 0. kg min 0 min 60 min hours 0. kg min 0 min 60 min hours 0. kg min 0 min 60 min hours 0 0. kg min 0 min 60 min hours 0 / 0. / 0. kg min 0 min 60 min hours n/a n/a 0 min 0 min 60 min hours n/a.0 kg 0 min 0 min 60 min hours

Product information ALSAN RS PRIMER Primer for modified bitumen (APP) WEIGHT 0 69 0. 0.07 kg ft per container kg / m kg / ft -0 wet mils -0 dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE RAIN PROOF NEXT LAYER FULLY CURED 0 0 0 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 6 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0-0 C (0-68 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (69-9 F) Coverage rates may vary depending on substrate conditions.

ALSAN RS Pocket Guide 6 7 ALSAN RS 76 PRIMER Primer for porous substrates WEIGHT 0 69 0. 0.07 kg ft per container kg / m kg / ft -0 wet mils -0 dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE 0 RAIN PROOF 0 NEXT LAYER 0 FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 6 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0-0 C (0-68 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (69-9 F) Coverage rates may vary depending on substrate conditions.

Product information ALSAN RS 0 FIELD (SUMMER FORMULATION) Polyester scrim reinforced liquid membrane resin WEIGHT kg 90 ft per container base layer.0 top layer.0 kg / m base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP C C 9 F à 7 F SUBSTRATE TEMP C 0 C à 7 F POT LIFE RAIN PROOF 0 NEXT LAYER 60 FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0 0. kg packets - C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets - C (60-9 F) Coverage rates may vary depending on substrate conditions. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

ALSAN RS Pocket Guide 8 9 ALSAN RS 0 FIELD (WINTER FORMULATION) Polyester scrim reinforced liquid membrane resin WEIGHT kg 90 ft per container base layer.0 top layer.0 kg / ft base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP - C 0 C 0 to F SUBSTRATE TEMP - C C 9 to F POT LIFE 0 RAIN PROOF NEXT LAYER 60 FULLY CURED 6 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0 0. kg packets - - 0 C ( - 9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

Product information ALSAN RS 0 FLASH (SUMMER FORMULATION) Polyester scrim reinforced liquid membrane application for vertical surfaces WEIGHT kg ft per container base layer.0 top layer.0 kg / m base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP C C 9 F to 7 F SUBSTRATE TEMP C 0 C to 7 F POT LIFE RAIN PROOF 0 NEXT LAYER 60 FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - C (7-9 F) CATALYST DOSAGE PER CONTAINER. 0. kg packets - C (60-9 F) Coverage rates may vary depending on substrate conditions. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

ALSAN RS Pocket Guide 0 ALSAN RS 0 FLASH (WINTER FORMULATION) Polyester scrim reinforced liquid membrane application for vertical surfaces WEIGHT kg ft per container base layer.0 top layer.0 kg / ft base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP - C 0 C 0 to F SUBSTRATE TEMP - C C 9 to F POT LIFE 0 RAIN PROOF NEXT LAYER 60 FULLY CURED 6 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - - 0 C ( - 9 F) CATALYST DOSAGE PER CONTAINER. 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

Product information ALSAN RS 60 LO FIELD Low odor polyester scrim reinforced liquid membrane application WEIGHT kg 90 ft per container base layer.0 top layer.0 kg / m base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE 0 RAIN PROOF NEXT LAYER FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0 0. kg packets - C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets - C (60-9 F) Coverage rates may vary depending on substrate conditions. ALSAN RS 60 LO Field requires the use of ALSAN RS LO Catalyst. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

ALSAN RS Pocket Guide ALSAN RS 60 LO FLASH Low odor polyester scrim reinforced liquid membrane application for vertical surfaces WEIGHT kg ft per container base layer.0 top layer.0 kg / ft base layer 0.9 top layer 0.09 kg / ft base layer 0-60 top layer -6 wet mils base layer 0-60 top layer -6 dry mils AMBIENT TEMP 9 F F 0 à C SUBSTRATE TEMP F F 0 à 0 C POT LIFE 0 RAIN PROOF NEXT LAYER FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - C (7-9 F) CATALYST DOSAGE PER CONTAINER. 0. kg packets - C (60-9 F) Coverage rates may vary depending on substrate conditions. Mil thickness rate does not take into account polyester fleece reinforcement thickness; measurement is for liquid resin only.

Product information ALSAN RS SELF-LEVELING MORTAR Heavy-duty trafficable surface combining ALSAN RS 0 and ALSAN RS Powder WEIGHT 0. 0. kg ft per container kg / m kg / ft 8-9 wet mils 8-9 dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE RAIN PROOF NEXT LAYER FULLY CURED 0 60 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions.

ALSAN RS Pocket Guide ALSAN RS 87 COLOR FINISH BASE + COLOR PACK Customizable thin-film color finish WEIGHT 0 0. 0.08 kg ft per container kg / m kg / ft - wet mils - dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE RAIN PROOF 0 NEXT LAYER 60 FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions.

Product information ALSAN RS 89 TEXTURED BASE + COLOR PACK Aggregate infused trafficable surface finish WEIGHT 0. 0. kg ft per container kg / m kg / ft -0 wet mils -0 dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE RAIN PROOF NEXT LAYER FULLY CURED 0 0 60 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 6 0. kg packets - C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets - C (60-9 F) Coverage rates may vary depending on substrate conditions.

ALSAN RS Pocket Guide 6 7 ALSAN RS PASTE Flexible resin paste WEIGHT N/A N/A N/A kg ft per container kg / m kg / ft N/A wet mils N/A dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE 0 RAIN PROOF 0 NEXT LAYER 60 FULLY CURED minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 6 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions.

Product information ALSAN RS DETAILER Micro-fiber infused flexible resin WEIGHT N/A.0 0.8 kg ft per container kg / m kg / ft N/A wet mils N/A dry mils AMBIENT TEMP 0 C C 9 F à F SUBSTRATE TEMP 0 C 0 C à F POT LIFE RAIN PROOF NEXT LAYER FULLY CURED 0 0 60 minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) minutes (at 0 C [68 F]) hours (at 0 C [68 F]) CATALYST DOSAGE PER CONTAINER 0. kg packets - 0 C (7-9 F) CATALYST DOSAGE PER CONTAINER 0. 0. kg packets 0 - C (0-9 F) Coverage rates may vary depending on substrate conditions.

ALSAN RS Pocket Guide 8 9 ALSAN RS FLEECE Non-woven, polyester fabric reinforcement LENGTH WEIGHT THICKNESS WIDTH 6 ft 0 m 0 g / m 0-0 (mils, nominal) 0 cm, po WIDTH WIDTH WIDTH WIDTH cm 0,7 po cm,8 po cm 0 po 0 cm po Allow for a minimum cm ( ) overlap at field and flashing side laps, 0 cm ( ) overlap at the end laps and a minimum 0 cm ( ) overlap at the base of the wall and all penetration flashings. QUARTZ AGGREGATE Chemically inert, kiln-dried quartz silica for providing skid resistant surfacing WEIGHT kg 0 lb.0 lb / ft.0 kg / m 00 QUARTZ 0 QUARTZ QUARTZ QUARTZ Color quartz blend options also available. Contact local sales representative for additional information.

Product information ALSAN RS CATALYST Reactive agent based on dibenzoyl peroxide used to induce curing in ALSAN RS products PACKAGING 0. kg PACKAGING kg DO NOT STORE IN DIRECT SUNLIGHT Refer to individual product information modules and product data sheets for proper catalyst activation quantities. ALSAN RS DECO CHIPS Paillettes de polymère minces et angulaires WEIGHT kg, lb Refer to individual product information modules and product data sheets for proper catalyst activation quantities.

ALSAN RS Pocket Guide 0

ALSAN RS Pocket Guide Surface Preparation Product Information Systems Information Application Information Details

System information

ALSAN RS Pocket Guide SYSTEM APPLICATIONS ALSAN RS systems allow for a number of waterproofing and surfacing systems, depending on the needs of a given application. Below is a selection of possible applications and surfaces. FULLY REINFORCED WATERPROOFING APPLICATIONS Roofing and Waterproofing System Construction ALSAN RS 76 Primer (as necessary) ALSAN RS 0 Field with ALSAN RS Fleece ALSAN RS 0 Field ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS Roofing and Waterprooing System with Custom Color Construction ALSAN RS 76 Primer (as necessary) ALSAN RS 0 Field with ALSAN RS Fleece ALSAN RS 0 Field ALSAN RS 87 Color Finish Base + Color Pack ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 60 LO Field and ALSAN RS 60 LO Flash may be used in place of ALSAN RS 0 Field and ALSAN RS 0 Flash, respectively, for a low odor application option.

System information

ALSAN RS Pocket Guide 6 7 PARTIALLY REINFORCED TRAFFICABLE SYSTEMS ALSAN RS Partially Reinforced Trafficable System with Deco Chips Construction. ALSAN RS 76 Primer. ALSAN RS Mortar with Deco Chips. ALSAN RS 8 Clear Finish ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS Partially Reinforced Trafficable System with Color Quartz Construction. ALSAN RS 76 Primer. ALSAN RS Self-Leveling Mortar with color quartz. ALSAN RS 8 Clear Finish ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 60 LO Field and ALSAN RS 60 LO Flash may be used in place of ALSAN RS 0 Field, ALSAN RS 0 Flash and ALSAN RS Mortar, respectively, for a low odor application option.

System information

ALSAN RS Pocket Guide 8 9 FULLY REINFORCED TRAFFICABLE SYSTEMS ALSAN RS Fully Reinforced Trafficable System with Deco Chips Construction. ALSAN RS 76 / Primer. ALSAN RS 0 Field -RS Fleece-ALSAN RS 0 Field. ALSAN RS Mortar with Deco Chips. ALSAN RS 8 Clear Finish ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS Fully Reinforced Trafficable System with Quartz Construction. ALSAN RS 76 Primer. ALSAN RS 0 Field -RS Fleece-ALSAN RS 0 Field. ALSAN RS Mortar with natural quartz aggregate. ALSAN RS 87 Color Finish Base + Color Pack ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS Fully Reinforced Trafficable System with Color Quartz Construction. ALSAN RS 76 Primer. ALSAN RS 0 Field -RS Fleece-ALSAN RS 0 Field. ALSAN RS Self-Leveling Mortar with color quartz. ALSAN RS 8 Clear Finish ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 60 LO Field and ALSAN RS 60 LO Flash may be used in place of ALSAN RS 0 Field and ALSAN RS Mortar, respectively, for a low odor application option.

System construction diagrams

ALSAN RS Pocket Guide 0 ALSAN RS 89 TEXTURED FINISH SYSTEMS ALSAN RS 89 Textured Base Partially Reinforced Balcony System Construction. ALSAN RS 76 Primer. ALSAN RS 89 Textured Base + Color Pack ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 89 Textured Base Heavy Duty Partially Reinforced System Construction. ALSAN RS 76 Primer. ALSAN RS LO Mortar. ALSAN RS 89 Textured Base + Color Pack ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 89 Textured Base Heavy Duty Fully Reinforced System Construction. ALSAN RS 76 Primer. ALSAN RS 0 Field -RS Fleece-ALSAN RS 0 Field. ALSAN RS Mortar. ALSAN RS 89 Textured Base + Color Pack ALSAN RS 0 Flash with ALSAN RS Fleece for details and flashing ALSAN RS 60 LO Field and ALSAN RS 60 LO Flash may be used in place of ALSAN RS 0 Field and ALSAN RS Mortar, respectively, for a low odor application option.

ALSAN RS Pocket Guide Basic Information Product Information Systems Information Application Information Details

ALSAN RS Pocket Guide CONTENTS PAGE Mixing 6 Catalyst dosage chart 7 Priming 8 Leveling with ALSAN RS Paste 60 Fully reinforced application 6 Protective and wear layer application 66 Surfacing applications 70 Drain installation 7 Pipe projection installation 76 Metal edge strip-in application 78 Control joint application 80 I-beam installation 8 Stair application 8

Mixing MIXING ALSAN RS systems are two- or multi-component products based on PMMA (polymethyl methacrylate) technology. The second component is a white catalyst powder which activates the curing reaction of the liquid resin product. Catalyst quantity is determined by resin amount and ambient temperature. When mixing, it is important to thoroughly mix the catalyst into the liquid resin. A slow-speed mechanical agitator (electric drill with a mixing paddle) should be utilized to ensure thorough mixing. For smaller quantities, the catalyst can be stirred into the liquid resin by hand using a stir stick. Always mix only as much resin as can be consumed based on product pot life. Use caution when handling products. Keep away from open flame, fire or any ignition source. Avoid skin and eye contact with this product. Workers must wear long sleeved shirts, long pants, work boots and use only butyl rubber or nitrile gloves. Safety glasses with side shields are required for eye protection. Use of NOISH approved respirator is required if the airborne concentration exceeds recommended limits. For more information, refer to relevant Material Safety Data Sheets (MSDS). CATALYST DOSAGE RESIN QUANTITY (KG) 0 0 % 0 0 CATALYST DOSAGE % 6 8 0 0 0 0 0 % 6 9 0 60 7 % 8 6 0 0 60 80 00 % 0 0 0 7 00 6% 6 8 0 60 90 0 0 TEASPOONS One teaspoon weighs approximately 0 grams or 0.00 kg. Each 0. kg packet of catalyst activator is equivalent to 0 level teaspoon.

ALSAN RS Pocket Guide 6 7 Standard equipment for application. Materials: liquid component, catalyst (white powder) and mixing paddle. Thoroughly stir liquid material in the bucket prior to catalyst activation. For batch mixing, pour off product (primer, resin, leveling mortar, etc.) into clean mixing bucket. Catalyst (according to mixing table, temperature and processing time) mixed with low-speed agitator. Mix for two () minutes. (Small amounts may also hand-mixed.)

Priming Before the start of the waterproofing work, prepare and clean areas of application and mask off application with masking tape. Prime surface as necessary (refer to substrate chart). Wood and concrete substrates must be primed. Apply primer via lambswool roller or brush. Consumption will depend on existing surface texture and roughness: approximately 0. kg / m. Apply primer by roller over entire surface. Consumption will depend on existing surface texture and roughness: approximately 0. kg / m.

ALSAN RS Pocket Guide 8 9 Immediately remove masking tape. The primed surface is ready after about 0 minutes for additional layers.

Leveling with ALSAN RS Paste ALSAN RS Paste is a thick resin used for leveling and preparation of substrate to eliminate voids. ALSAN RS Paste can be mixed at a : ratio with quartz sand. Add necessary quantity to a mixing bucket...... Add catalyst activator and mix throroughly.

ALSAN RS Pocket Guide 60 6 Prime all areas prior to application of ALSAN RS Paste. Fill cavities, etc. The filler can be applied with a trowel or spatula. Consumption depends on the nature of the substrate. Rule of thumb: about kg per m at one millimeter thickness. Allow the paste to cure for minutes prior to subsequent layer applications. 6

Fully reinforced application Before the start of the waterproofing work, prepare and clean areas of application and mask off application with masking tape. Roll catalyzed resin onto prepared substrate. Provide sufficient liquid, especially onto vertical surfaces (about.0 kg / m ). Apply the previously cut fleece into wet catalyzed liquid resin. Roll fleece into liquid resin, removing air bubbles and wrinkles with a roller. Any fleece overlaps require additional application of catalyzed liquid resin between fleece layers.

ALSAN RS Pocket Guide 6 6 Immediately roll in additional catalyzed resin, fully saturating fleece. Visible white areas in fleece reinforcement are evidence of too little material being applied. Consumption: approximately.0 to. kg / m. Pour catalyzed resin onto prepared substrate. Provide sufficient material for the fleece embedment layer (about. kg / m ). Evenly distribute catalyzed liquid resin with a lambswool roller or /6 in. ( mm) notched squeegee. 6

Fully reinforced application Install ALSAN RS Fleece reinforcement directly into wet catalyzed liquid resin. Roll fleece into liquid resin, removing air bubbles and wrinkles with roller. Apply additional catalyzed resin over fleece. 7 Immediately roll catalyzed resin, fully saturating fleece. Visible white areas in fleece reinforcement are evidence of too little material being applied. Consumption: approximately.0 to. kg / m. 8 9

ALSAN RS Pocket Guide 6 6 The surface is cured after about 60 minutes for additional layers, as required. 0

Protective and wear layer application Apart from the actual product components that are used to create the protective layers, the following tools are needed: Large mixing bucket, spiked roller, trowel, etc. It is important to ensure a clean and tidy mixing area. The required product components for the creation of ALSAN RS Self-Leveling Mortar: ALSAN RS 0, ALSAN RS Mixing Powder, catalyst. The first two components are mixed. This mixture can be stored (ALSAN RS mortar course, without a catalyst), for approximately one week and must be mixed again prior to the addition of the catalyst activator. After mixing the first two components, add the prescribed amount of catalyst. Mix well.

ALSAN RS Pocket Guide 66 67 Apply mixed material to the primed substrate or previously installed layers. Apply with a trowel...... Distributing evenly. Consumption:. -. kg / m.

Protective and wear layer application Use a spiked roller in order to even out the application. As specified, sprinkle with natural quartz, colored quartz or Deco Color Chips. Allow about 60 minutes to cure before application of subsequent layers. 6 7

ALSAN RS Pocket Guide 68 69

Surfacing applications Mask application edges with masking tape. Apply ALSAN RS 87 Color Finish Base + Color Pack. Consumption: approximately 0. kg / m. Immediately remove masking tape. Apply ALSAN RS 87 Color Finish Base + Color Pack with a lambswool roller, trowel or flat-edged squeegee. Consumption: approximately 0.6-0.8 kg / m.

ALSAN RS Pocket Guide 70 7 Prior to curing, immediately apply decorative vinyl chips with the hopper gun or by hand. Consumption: approximately 0.0-0. kg / m. Finished surface. No further sealing is necessary. The area is accessible after one hour and can withstand consistent trafficking after one day.

Surfacing applications Variant surfacing application used to achieve a required slip resistance and increased abrasion strength Prior to curing of mortar course, broadcast natural or colored kiln-dried quartz aggregate to excess. Grain size selection is dependent upon trafficking requirements. Sweep off excess sand. The aggregated surface can be coated with ALSAN RS 87 Color Finish Base + Color Pack or ALSAN RS 8 Clear Finish after about minutes. Note: This aggregated surface must always be sealed.

ALSAN RS Pocket Guide 7 7 Prepare given substrate as necessary. Wood and concrete surfaces must be primed with ALSAN RS 76 Primer. Apply primer with lambswool roller or brush. Consumption: approximately 0. kg / m. Pre-cut all ALSAN RS Fleece. Allow primer to cure approximately 0 minutes. Mask off area with masking tape. Apply ALSAN RS 0 Flash with a brush or lambswool roller. Consumption: about.0 kg / m. Install pre-cut fleece into wet ALSAN RS 0 Flash. Use roller to eliminate wrinkles and air bubbles. Completely saturate all fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps.

Drain application Apply additional application of ALSAN RS 0 Field in preparation for target fleece installation. This layer may be applied concurrently with initial fleece installation; there is no waiting period between fleece installations. Fully saturate second fleece installation, removing all wrinkles and air bubbles. Consumption:.0 to. kg /m. Immediately remove masking tape. No drain clamping ring installation is subsequently required. 6

ALSAN RS Pocket Guide 7 7 Prior to start of application, prime areas as necessary. Apply masking tape to application edges. Prepare metal surface by abrading metal, removing existing coatings, rust. Wipe with ALSAN RS Cleaner. Pre-cut ALSAN RS Fleece polyester reinforcement prior to resin activation. Apply ALSAN RS 0 Flash with a lambswool roller. Consumption: about.0 kg / m. Install pre-cut fleece into wet ALSAN RS 0 Flash. Use roller to eliminate wrinkles and air bubbles. Completely saturate all fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps. Saturate fleece on vertical surface with ALSAN RS 0 Flash. Consumption: approximately.0 to. kg / m.

Pipe projection installation While still wet, install RS Fleece target reinforcement around horizontal base. Apply ALSAN RS 0 Flash. Consumption: approximately.0 to. kg / m. Promptly remove masking tape prior to ALSAN RS 0 Flash curing.

ALSAN RS Pocket Guide 76 77

Metal edge strip-in Prior to application, prepare surface via metal abrasion. Wipe surface with ALSAN RS Cleaner with a rag in order to thoroughly clean surface. Allow to dry prior to continuing application. Mask off area with masking tape prior to application. Apply ALSAN RS 0 Flash with a brush or lambswool roller. Consumption: about.0 kg / m. Install ALSAN RS Fleece into wet ALSAN RS 0 Flash.

ALSAN RS Pocket Guide 78 79 Use the roller to eliminate any wrinkles or air bubbles. Completely saturate the fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps. While still curing, apply a top application of ALSAN RS 0 Flash in order to complete liquid membrane construction. Consumption: approximately.0 to. kg / m.

Control joint Prior to start of application, prime areas as necessary. Apply masking tape to application edges. Apply ALSAN RS 0 Flash with a lambswool roller. Consumption: about.0 kg / m. Install ALSAN RS Fleece reinforcement into wet ALSAN RS 0 Flash. Use the roller to eliminate any wrinkles or air bubbles. Completely saturate the fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps.

ALSAN RS Pocket Guide 80 8 While still curing, apply a top application of ALSAN RS 0 Flash in order to complete liquid membrane construction. Consumption: approximately.0 to. kg / m. Immediately remove masking tape. Please note: This assembly is for joints with low to moderate expected movement. More dynamic movement requires a different assembly. Contact Technical Services for additional information.

I-beam application Prior to start of application, prime areas as necessary. Apply masking tape to application edges. Prepare metal surface by abrading metal, removing existing coatings, rust. Wipe with ALSAN RS Cleaner. Apply ALSAN RS 0 Flash with a lambswool roller. Consumption: about.0 kg / m. Install ALSAN RS Fleece reinforcement into wet ALSAN RS 0 Flash. Use roller to eliminate any wrinkles or air bubbles. Completely saturate the fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps. While still curing, apply a top application of ALSAN RS 0 Flash in order to complete liquid membrane construction on vertical reinforcement. Consumption: approximately.0 to. kg / m.

ALSAN RS Pocket Guide 8 8 While still wet, install RS Fleece target reinforcement around horizontal base of I-beam. Immediately apply ALSAN RS 0 Flash in order to complete liquid membrane construction. Consumption: approximately.0 to. kg / m. Promptly remove all masking tape prior to liquid membrane curing.

Stair application The following series of photos illustrate a fully reinforced staircase application. Very often, in practice, only planar transition changes are fleece reinforced. Surface substrate should be properly prepared. Refer to substrate preparation chart for additional information. Prime surface as necessary. Wood and concrete surfaces require primer application. Apply primer with a brush or lambswool roller. Consumption: 0. kg / m depending on surface texture. Allow to dry approximately 0 minutes.

ALSAN RS Pocket Guide 8 8 Apply catalyzed ALSAN RS 0 Flash. Consumption: about. kg / m.... and spread with a roller. 6 Install ALSAN RS Fleece reinforcement into wet ALSAN RS 0 Flash. Use the roller to eliminate any wrinkles or air bubbles. Completely saturate the fleece. Additional liquid resin should be applied in areas where the fleece reinforcement overlaps.

Stair application While still curing, apply a top application of ALSAN RS 0 Flash in order to complete liquid membrane construction. Consumption: approximately.0 to. kg / m. Allow to cure for 0 minutes prior to wearing surface applications. 7 Use ALSAN RS Paste as a setting bed for the protective metal edge profile installation. 8 9

ALSAN RS Pocket Guide 86 87 0 Apply catalyzed ALSAN RS Paste directly to clean and dry ALSAN RS 0 application. Consumption depends on the nature of the substrate. Rule of thumb: about kg / m and one millimeter in thickness. Install the metal edge profile, pressing them into wet ALSAN RS Paste. The metal edge profiles are recommended for slip resistance purposes.

Stair application Apply masking tape to metal edge profiles. Mix mortar course (see ALSAN RS Self-Leveling Mortar), catalyze and apply...... and distribute onto horizontal surfaces with a trowel. Consumption:. -.0 kg / m. Immediately remove masking tape. Allow to dry approximately 0 minutes prior to subsequent applications. Apply masking tape over metal edge profiles. Mix and catalyze ALSAN RS 87 Color Finish Base and apply...

ALSAN RS Pocket Guide 88 89... and spread with a lambswool roller. Consumption: 0.6-0.8 kg / m. Immediately remove masking tape. 6 The staircase is accessible after one hour and able to withstand heavy traffic after one day. 7

ALSAN RS Pocket Guide 90 9 Surface Preparation Product Information Systems Information Application Information Details

ALSAN RS Pocket Guide 9 9 DETAILS PAGE Inside corner detail 9 Outside corner detail 9 Standard wall flashing 96 Brick wall flashing w/ reglet 97 Drain flashing 98 Metal edge tie-in 99 Pipe projection 00 Rail post projection 0

Details Inside Corner Detail ALSAN 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 / Primer (as necessary) Prepared substrate

ALSAN RS Pocket Guide 9 9 Outside Corner Detail ALSAN 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate

Details Standard Wall Flashing ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate 0 cm (8 " ) MIN. 0 cm ( ")

" ( cm ) MIN. " ( 0 cm ) MIN. 8 ALSAN RS Pocket Guide 96 97 Brick Wall w/ Reglet ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN RS 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate cm ( ) MIN. 0cm (8 ) MIN. 0 cm ( " )

Details Drain Flashing ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate 0 cm ( " ) MIN. cm ( " ) MIN. NOTE: Drain ring clamp installation is optional in ALSAN RS fluid-applied membrane application.

ALSAN RS Pocket Guide 98 99 Metal Edge Flashing ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN RS 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate 0 cm ( " ) cm ( " ) MIN.

Details Pipe Projection ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN RS 0 Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate cm ( 6 " ) cm ( " ) 0 cm ( " )

ALSAN RS Pocket Guide 00 0 Rail Post Penetration ALSAN RS 0 Field / ALSAN RS Fleece / ALSAN RS 0 Field ALSAN 0 RS Flash / ALSAN RS Fleece / ALSAN RS 0 Flash ALSAN RS 76 Primer (as necessary) Prepared substrate cm ( " ) MIN. 0 cm ( " ) MIN.

BR96_v.060 SOPREMA CANADA 688, Jean-Berchmans-Michaud Drummondville, Quebec, JC 8E9 Canada 877 MAMMOUTH www.soprema.ca www.alsan.us