T-Rib Roofing System

T-Rib Roofing System Installation Manual 3449 Hempland Road Lancaster, PA 17601 (717) 397-2741 308 Alabama Blvd. Jackson, GA 30233 (770) 775-4484 World Wide Web: www.fabral.com E-Mail: fabinfo@fabral.com 10/01(9832-728) A-900 8 2001 FABRAL

Table of Contents General Notes Hem Lengths Thermal Movement Table Accessories T-Rib Specifications Product Application Endlap Detail Details Dormer Details 4 5 5 5 6-8 9-10 11 12-19 20-22 ROOF/FASCIA TRANSITION PEAK VALLEY PITCH BREAK WITHOUT FASCIA SIDEWALL VENT PIPE (LIGHT EQUIP- MENT CURB) HEAVY EQUIP- MENT CURB RIDGE GABLE GABLE FASCIA (OUTSIDE CORNER) EAVE WITH GUTTER EAVE WITHOUT GUTTER FASCIA (INSIDE CORNER) 3

T-Rib Architectural Roofing T-RIB SSR SYSTEM General Notes and Installation Recommendations A. GENERAL NOTES 1. This booklet has been prepared to assist the designer and installer with various recommended details and installation procedures. Each project usually requires its own specially designed details. The details included can be used as a guide in designing project details. 2. Each roof panel is manufactured with four (4) minor stiffening ribs in the flat area to minimize oil-canning. However, due to the limitations of commercially available metals, some oil-canning should be anticipated and is not cause for rejection. 3. The erection of the T-Rib roof system can begin at either end of the building. 4. Whenever possible, workers should walk on the panel ribs rather than the flat of the panel. Boards or plywood should be placed over panels in areas which receive excessive foot traffic (such as roof top equipment, skylights, etc.). 5. Flashings must lap a minimum of 6". Treat flashing endlaps similar to a panel endlap detail using two rows of sealant tape with stitch screws 4" o.c. maximum. 6. Sealants: (a) Quality long-life butyl sealants work best as a gasket sandwiched between two pieces of metal. (b) One part polyurethane sealants are recommended when voids must be filled. 9. Jobsite handling: (a) Panel crates must be lifted at bundle block locations. (b) Do NOT lift material with ropes or wires. (c) Do NOT lift panels greater than 25'-0" long without a spreader bar. (d) Do NOT lift panels from ends while flat. DO lift panels on edge. B. PROPER STORAGE If the material is not to be used immediately, it should be stored in a dry place where little moisture can contact it. Moisture (from rain, snow, condensation, etc.) trapped between pieces of material may cause water stains or white rust which can affect the service life of the material and will detract from its appearance. To avoid staining or white rust, store the material in a well ventilated, dry area. Break the steel strapping bands used for shipment and store the material stacks material in an inclined position. If outdoor storage cannot be avoided, protect the material with a canvas or waterproof paper cover. Do not use plastic which can cause condensation. Keep the material off the ground in an inclined position with an insulator such as wood. It is the responsibility of the contractor to insure that all materials are properly stored at the jobsite. C. INSTALLATION PROCEDURES 1. Check the structural support system to be sure it is straight and square and that the tops of all members are in the same plane. Vertical camber in roof supports can cause water to pool on low pitched roofs. Misaligned structures can greatly increase the amount and degree of oil-canning. 2. Fasten each clip to the roof support member with the appropriate screw fastener. Clips are furnished pre-drilled to accept #12 screws. 3. For applications requiring endlaps, install the first panel (down-slope panel) like a normal panel. Prior to installing the upslope panel, place the back-up plate onto the installed downslope panel. Position the endlap sealant tape and place the upslope panel into position. Install the upslope panel as outlined in the endlap details. Secure the endlap with four (4) self-drilling, self-tapping screws, as shown on the detail. Connect all beads of sealant prior to placement of the cap-lock at panel endlaps. For ease of installation, install the clip at the endlap prior to installing the remaining clips on the upslope panel. D. FINAL CAP STRIP SEAMING 1. The cap strip seaming with the electric closure machine is begun after all other erection sequences are complete. 2. Remove closure machine from shipping box. 3. Install handle in position on motor mount stanchion. Insert clevis pin with washer through pivot holes. Insert retaining washer and spring pin. 4. To operate, use an approved electrical cord and plug into a 115 volt A.C. source. 5. Determine direction of operation and starting location on roof panel assembly. 6. Open seaming dies by moving lock lever to unlock position. At same time, raise handle of closing mechanism opening seaming dies to fully open position, approximately 30 degrees to each side of closure machine. 7. Lift closure machine and place in position where cap strip has been hand seamed. Insure front and rear guide blocks are aligned with panel ribs, are properly seated, and cam followers are along the sides of the cap strip. 8. Close seaming dies by moving lock lever into lock position. 9. Turn electric switch on, machine will begin seaming cap strip. 10.Operator should maintain alignment to panel ribs at same time applying slight forward pressure to assist movement along roof panel rib. 11. Upon reaching end of panel ribs, turn power switch off. Never install or remove closure machine while running. 12. Open seaming dies by moving lock lever to unlock position, releasing lock on left side of base platform, at same time raise handle of closing mechanism. 13. Position closure machine on next area of ribs to be seamed. Do not let closure machine sit directly on top of panels or it may mar the finish. 14. It is suggested that the closure machine be placed approximately 3 feet from the ridge and faced toward it and then seamed. Machine is then turned 180 degrees and seaming to the eave is completed. 15. The closure machine is not self-propelled but requires some pushing. A slightly firmer push may be needed at clip locations. 16. Inspect each seam after completion. Machine may be re-run over seam if required. 4

HEM LENGTHS The length of the hem at the end of a panel will vary with the change in temperature that the panel experiences and the length of the panel. Unless a more exact analysis of the temperature during installation compared to the maximum and minimum anticipated temperature is conducted, use the following equation and Thermal Movement Table. When installing panels, be sure to leave room at the end of the panel that will experience movement for the "starting gap" which is the required air space (X) between the panel and cleat. X 2X + 1/4" OVERALL HEM LENGTH THERMAL MOVEMENT TABLE Panel movement (in.) with a 100 F temperature change in the panel and a 50 F temperature change in the substrate. PANEL MATERIAL steel aluminum SUBSTRATE MATERIAL rigid insulation wood steel concrete rigid insulation wood steel concrete PANEL LENGTH(FT.) 10' 50' 100' 3/32" 13/32" 25/32" 1/16" 3/8" 5/8" 1/16" 3/8" 13/32" 1/16" 3/8" 15/32" 5/32" 25/32" 1 9/16" 5/32" 11/16" 1 3/8" 1/8" 19/32" 1 5/32" 1/8" 5/8" 1 7/32" CLIPS ACCESSORIES CLIPS ARE AVAILABLE IN STAINLESS STEEL AND GALVANIZED STEEL. CLOSURE MISC. USE STAINLESS STEEL CLIPS FOR EITHER STEEL OR AC 3 ROOF CLIP, 1/4" STAND OFF, AC 5 ROOF CLIP, 1 1/4" STAND ALUMINUM PANELS. USE 18GA., TWO HOLES, UL 90 RATED. OFF, 18 GA., TWO HOLES, UL 90 GALVANIZED STEEL CLIPS FOR RATED. STEEL PANELS ONLY. TOOLS METAL TOP CLOSURE, GAUGE, COLOR AND WIDTH TO MATCH PANEL. PLATES TOUCH-UP PAINT # 10-16 x 1" PHILLIPS PANCAKE HEAD, TYPE "A", SELF-TAPPING. # 10-16 x 1" PHILLIPS PANCAKE HEAD, SELF- DRILLING, SELF- TAPPING. HAND CRIMPING TOOL BEARING PLATE, 4" x 4", 20 GA.(USED FOR CLIPS INSTALLED OVER RIGID INSULATION) FILTER PLATE, "KNEE CAP", GAUGE AND COLOR TO MATCH PANEL. #12-14 x 1" PHILLIPS PANCAKE HEAD, TYPE "A", SELF TAPPING. #12-14 x 1" PHILLIPS PANCAKE HEAD, SELF-DRILLING. ELECTRIC SEAMER END DAMMING TOOL BACK UP PLATE, 16 GA. (USED AT END LAPS OR RIDGES FOR EXTRA SUPPORT) THERMAL BLOCK, 1" x 4" x 17 1/2" POLYSTYRENE BLOCK. 5

T-Rib Architectural Roofing 5/8" 1 1/2" CAP STRIP 12", 16", OR 18" 2 3/8" 1 1/2" 1/16" 1 1/2" 2 7/16" 2 7/16" SEAM WITH CLIP BEFORE SEAMING SEAM WITH CLIP AFTER SEAMING ALLOWABLE WIND UPLIFT LOAD (PSF) substrate width 3.0' 3.5' 4.0' 4.5' 5.0' 24 ga. steel 12" 75 65 57 50 45 24 ga. steel 18" 57 48 42 38 34 22 ga. steel 12" 94 81 71 63 56 22 ga. steel 18" 71 60 53 48 43.032" alum. 12" 55 52 49 46 42.032" alum. 18" 42 39 37 34 32 Notes: 1. Allowable loads are based on 1980 edition of AISI specifications. 2. Deflection is limited to L/240 of span. 3. Loads are based on spans of 3 or more. 4. FY = 50 ksi for steel panels. 5. Uplift values based on attachment to 16 ga. purlins with 2 #10-16 SD ST screws. DESIGN INFORMATION The T-Rib panels can be custom tapered to a minimum width of 23" and a maximum width of 18". The maximum length of tapered panels is 40'. The maximum purlin spacing for the T-Rib panels is 4'. Minimum roof slope is 2:12. Panel can be curved in the field to a minimum radius of 200'. Maximum panel length is 65'. Minimum panel length is 6'. TEST REPORT SUMMARIES AIR INFILTRATION: had 0.015 cfm/sq ft leakage with 6.24 psf pressure differential per ASTM E283. WATER RESISTANCE: No water penetration under 5 gal./hr. spray at 6.24 psf pressure differential per ASTM E 331. UL90 UPLIFT RATING: 18" wide, 24 ga. panels on 16 ga. purlins (50 ksi yield strength) spaced 4' o.c. with two screws per clip and up to 6" of insulation between the panels and purlins (Construction No. 103). UL90 UPLIFT RATING: like Construction No. 103 (above) but with optional foamed plastic insulation (13" to 12" thickness) between panels and purlins and with butts occurring over purlins (Construction No. 139). UL90 UPLIFT RATING: 18" wide, 24 ga. panels on 2" plywood with clips spaced 2' o.c. and two #12-14 screws per clip (Construction No. 415). UL90 UPLIFT RATING: 18" wide, 24 ga. panels on 22 ga. deck (33 ksi yield strength) with clips spaced 2' o.c. Clips are fastened to deck with two #14 truss-head, No. 3 Phillips drive, self-drilling screws per clip. Bearing plates (42" x 6" x 24 ga.) are required under each clip. One to 4" of rigid insulation (2 pcf density) is optional between the panel and deck (Construction No. 416). 6

T-Rib Architectural Roofing T-Rib Metal Roofing Suggested Specification PART 1: GENERAL 1.01 SUMMARY A. Section includes: Prefinished, prefabricated, mechanically seamed, structural standing seam roof system and accessories. B. Related Sections 1. Metal decking 2. Rough carpentry, plywood, and underlayment 3. Insulation 4. Membrane roofing 5. Flashing and sheet metal 6. Joint sealers: sealants and caulk 7. Structural framing. 1.02 REFERENCES A. American Society for Testing and Materials (ASTM) 1. ASTM A 653: Steel Sheet, Zinc-Coated by the Hot Dip Process 2. ASTM A 792: Steel Sheet, Aluminum -Zinc Alloy Coated by the Hot Dip Process. 3. ASTM B 209: Aluminum and Aluminum Alloy Sheet and Plate. 4. ASTM E 283: Air leakage 5. ASTM E 331: Water penetration B. Underwriters Laboratory 1. UL Building Materials Directory C. Sheet Metal and Air Condition Contractors National Association, Inc. (SMACNA) 1. SMACNA Architectural Sheet Metal Manual, 1993 Edition. D. American Iron and Steel Institute (AISI) 1. AISI Cold Formed Steel Design Manual E. Metal Construction Association (MCA) 1. Preformed Metal Wall Guidelines F. Code references 1. ASCE, Minimum Loads for Buildings and Other Structures 2. BOCA National Building Code 3. UBC Uniform Building Code 4. SBC Standard Building Code 1.03 SYSTEM DESCRIPTION A. Performance Requirements: Provide factory formed, prefinished, mechanically seamed, concealed clip, structural standing seam metal roof system, that has been pretested and certified by manufacturer to comply with specified requirements under installed conditions. 1. Provide UL90 rated roofing system that has been tested in accordance with UL 580 test procedure. 2. Resistance to air leakage: 0.015 cfm/ft. of joint leakage when tested in accordance with ASTM E 283 at static pressure differential of 6.24 psf. 3. Resistance to water penetration: No leakage through panel joints when tested in accordance with ASTM E 331 at static pressure differential of 6.24 psf. B. Structural Requirements: Engineer panels for structural properties in accordance with latest edition of American Iron and Steel Institute=s Cold Formed Steel Design Manual using Aeffective width" concept and Aluminum Association=s Aluminum Design Manual. C. Maximum clip spacing shall be 4' o.c. 1.04 SUBMITTALS A. Product Data: submit manufacturer's specifications, standard profile sheet, product data brochure and finish warranty. B. Shop Drawings: shop drawings showing roof plan with layout of panels, clips, clip attachment, underlayment and sections of each flashing/trim condition shall be submitted for approval prior to fabrication. Drawings shall contain material type, metal thickness and finish. Drawings shall distinguish between factory and field fabrication. C. Samples: 1. Submit sample 12" long x full width panel, showing proposed metal gauge, seam profile and specified finish. 2. Submit manufacturers standard colors for Architect's selection. D. Test Reports: 1. Submit the test reports prepared by Underwriters Laboratory indicating wind uplift rating of proposed roof system. The manufacturer must be listed by name in the UL Directory. 2. Air leakage per ASTM E 283 and Water penetration per AST M E 331. (Actual independent laboratory certified test results must be submitted). E. Certification: Submit manufacturer's certification that materials and finishes meet specification requirements. 1.05 QUALITY ASSURANCE A. Panel manufacturer shall have a minimum of ten (10) years of experience in manufacturing architectural roofing in a permanent stationary indoor facility. B. Panel installer shall have a minimum of two (2) years experience in the installation of concealed clip architectural standing seam metal roofing and show evidence of successful completion of at least three (3) projects of similar size, scope, and complexity. 1.06 DELIVERY, STORAGE, and HANDLING A. Panels shall be protected and properly packaged to protect against transportation damage in transit to the jobsite. B. Upon delivery, exercise care in unloading, stacking, moving, storing, and erecting panels to prevent twisting, bending, scratching, or denting. C. Store panels in a safe, dry environment under a waterproof covering to prevent water damage. Allow for adequate ventilation to prevent condensation. Panels and flashings with strippable film shall not be stored in direct sunlight. D. Upon installation immediately remove strippable film from panels and flashings. Protect panels and flashings from foot traffic and from all other trades. 1.07 PROJECT CONDITIONS A. Field dimensions shall be taken prior to fabrication to verify jobsite conditions. 1.08 WARRANTIES A. Panel manufacturer shall provide a twenty (20) year warranty on the paint finish covering chalking, cracking, checking, chipping, blistering, peeling, flaking, and fading. B. Applicator shall furnish written warranty for a two (2) year period from date of substantial completion of building covering repairs required to maintain roof and flashings in watertight conditions. Part 2 PRODUCTS 2.01 PRODUCT DESCRIPTION A. T-Rib structural standing seam roof system as manufactured by Fabral, 3449 Hempland Road, Lancaster, PA 17601, ph.: 800-477-2741; fax: 800-283-4289. B. Panels: The T-Rib panel shall have a width of 12", 16", or 18" wide. Seams shall be 22" high with a 2" top flange angled at 90 degrees from the seam to facilitate the seaming of the panel and cap. The panels shall have 1/16" x 1" stiffening ribs in the pan of the panel. C. Roof panels shall use a one-piece roof clip allowing for thermal movement of the panel system. D. The panel shall have a factory applied mastic and be mechanically seamed with a field operated electric seaming machine provided by the manufacturer. E. The panel system shall be as a true standing seam shape requiring no trapezoidal foam closures, plugs, or fillers at eaves. F. The maximum cap length shall be 30'. 2.02 PRODUCT SUBSTITUTIONS A. Requests to use alternate systems shall be submitted in writing to the project designer at least ten (10) days prior to bid date. Request shall demonstrate proposed substitution meets or exceeds specified performance requirements. Certified 7

T-Rib Architectural Roofing statements, samples and descriptive data shall be included in this submittal request. B. Manufacturers listed in this section are prequalified manufacturers. Substitution of manufacturer's products for those specified shall not be allowed at anytime during construction. 2.03 MATERIALS AND FINISHES A. Panel materials 1. 24 or 22 gauge, Grade 50 (50 ksi yield strength) structural steel with G90 (0.90 oz./ft. 2 ) hot dipped galvanized coating, both conforming to ASTM A 653. 2. 24 or 22 gauge, Grade 50 (50 ksi yield strength) structural steel with AZ50 (0.50 oz./ft. 2 ) aluminum-zinc alloy coating, both conforming to ASTM A 792. 3. 0.032" or 0.040", 3105-H14 or equal (20 ksi yield strength) aluminum alloy conforming to ASTM B 209. B. Texture: panels shall be smooth C. Finish: paint shall be full strength 70% polyvinylidene fluoride (Kynar/Hylar* fluorocarbon) baked-on coating, factory applied prior to roll forming. The treatment shall be a two-coat system consisting of a single coat of 0.2 mil. primer followed by a finish coat of 0.8 mil. Kynar topcoat with a total dry film thickness of 1.0 mil 0.2 mil. The reverse side of the panels shall be treated with a back coat system consisting of a 0.2 mil. primer with a 0.3 mil. topcoat for a total dry film thickness 0.5 mil. 2.04 ACCESSORIES A. Concealed clips: 1. AC3 roof clip: a one piece, 18 ga. galvanized steel or (stainless steel), 3" stand-off, used on purlins (with or without up to 4" vinyl faced batt insulation) or light gauge framing and metal decking (with or without rigid insulation board and a bearing plate). 2. AC4 roof clip: a one piece, 18 ga. galvanized steel ( or stainless steel), 3" stand-off used on bar joist (with or without up to 4" vinyl faced batt insulation). 3. AC5 roof clip: a one piece, 18 ga. galvanized steel (or stainless steel), 1 3" stand-off used on purlins (with 4" t o 8" batt insulation). 4. Deck style roof clip: a one piece, 22 ga. galvanized steel used on plywood underlayment. B. Flashing and Trim 1. All flashing and trim shall be of the same material, gauge, finish, and color as the roof panels and fabricated in accordance with standard SMACNA procedure and details. 2. Provide transition rib covers where roofing changes pitch. 3. Fabricate gutters and downspouts in the same gauge, material, finish, and color as the roof panels. C. Fasteners 1. Clips to substrate: screw shall be #12-14, self tapping type, zinc-plated steel. 2. Flashings to panels: exposed screws shall be zinc plated with a #14 x f" combination steel and neoprene washer, color to match panel. 3. Pop rivets: #43 stainless steel, color finish to match panel. D. Sealants 1. Shall not contain oil, asbestos, or asphalt. 2. Factory applied weatherstripping shall be applied in the seam cap and designed for metal to metal concealed joints. 3. Field applied panel end sealant shall be mastic tape sealant. 4. Exposed sealant shall be one-part polyurethane joint sealant. Coordinate color with roof panels. E. Closures 1. Ridge and hip closures shall be protected and supported by a formed metal closure manufactured from the same material, color, and finish as the panels. 2. Metal closures shall be factory fabricated and field-cut as needed. F. Thermal blocks 1. Thermal blocks shall be: a. Non-treated wood as per manufacturer=s recommendation. b. Extruded polystyrene block. c. EPDM membrane. G. Vapor Retarder: 1. Retarder with a permeance of 0.05 or less as determined by ASTM E 98. 2.05 RELATED MATERIALS A. Refer to other sections listed in Related Sections paragraph for related materials. 2.06 FABRICATION A. Roof panels shall be formed in continuous lengths. End laps will not be allowed. B. Panels shall be roll formed on a stationary industrial type rolling mill to gradually shape the sheet metal. Portable rollformers, rented or owned by the installer, are not acceptable. C. Fabricate flashings from the same material as the roof system. 2.07 SOURCE QUALITY A. Source Quality: obtain metal panels and accessories from a single manufacturer. B. Fabrication tolerances: follow tolerances in MCA=s Preformed Metal Wall Guidelines. C. Tests and inspections D. Verification of performance PART 3 EXECUTION 3.01 MANUFACTURER=S INSTRUCTIONS A. Compliance: Comply with manufacturer=s product data, including product technical bulletins, product catalog installation instructions, and product cartons for installation. 3.02 EXAMINATION A. Installer shall: 1. Inspect roof deck and/or purlins to verify that it complies with shop drawings and is smooth, even, sound, and free of depressions. 2. Report variations and potential problems in writing to the architect. 3.03 INSTALLATION A. Conform to the standard set forth in the SMACNA architectural sheet metal manuals and the approved shop drawings detailed for the project. B. Install panels plumb, level, and straight with the seams parallel, conforming to the design as indicated. C. Install panel system so it is watertight, without waves, warps, buckles or distortions, and allow for thermal movement considerations. D. Abrasive devices shall not be used to cut on or near roof panel system. E. Apply sealant tape or caulking as necessary at flashing and panel joints to prevent water penetration. F. Remove any strippable film immediately upon installation. G. Hand-crimp battens at each clip or mechanically seam before workers stand on panels. H. Seam panels together with electric-powered seaming machine supplied by the panel manufacturer for a weathertight seam. I. Vapor retarder: The joints, perimeter, and all openings shall be sealed per the manufacturer's instructions to provide a continuous vapor retarder. J. Underlayment (solid substrat e): 1. Provide one layer of 30# felt with horizontal overlaps and endlaps staggered between layers. 2. Provide ice and water shield membrane at all valley and eave conditions as well as any area at less than a 3:12 slope. 3. Lay parallel to ridge line with 22" horizontal laps and 6" vertical laps 3.04 CLEANING A. Dispose of excess materials and debris from jobsite. B. Remove filings, grease, stains, marks, or excess sealants from roof panel system to prevent staining. C. Protect work from damage from other trades until final acceptance. 8

T-Rib Architectural Roofing * Kynar 7 500 is a registered trademark of Elf Atochem North America, Inc. * Hylar 7 5000 is a registered trademark of Ausimont USA, Inc. 9

1 1/2" 12", 16", & 18" COVERAGE 2 3/8" 1/16" x 1" STANDARD RIBS PROFILE PRODUCT APPLICATION 1" x 1" TUBING FIELD BEND BOTTOM OF PANEL UP WITH BENDING TOOL. BE CAREFUL NOT TO TEAR THE PANEL NEAR THE SEAMS. 2-2" x 2" x 1/4" ANGLES WELDED AS SHOWN. VARIES AS REQ'D BOX END DETAIL (AT RIDGES, HIPS, PEAKS, ETC.) BOX END OR HEMMED END BENDING TOOL 5-#14x7/8" 1 1/2" 1"x3/32" MASTIC. CONT. ALONG TOP OF CLOSURE GUN GRADE MASTIC METAL TOP CLOSURE (AT RIDGES, HIPS, PEAKS, ETC.) 9

UPSLOPE CAP STRIP. HAND CRIMP OVER LOWER CAP. PANEL RIBS DOWNSLOPE CAP STRIP. HAND CRIMP END. HAND CRIMP AT ROOF CLIPS. 1" LAP PUSH OUT (BEFORE) (AFTER) HAND CRIMPING TOOL 10

END LAP DETAIL 6" LAP 2 1/ 2 (2) ROWS TAPE MASTIC (1) ROW GUN GRADE MASTIC #12x1 1/4" CLIP BACK PLATE PURLIN 1 1/ 2 " 9 1/ 2 FOLD MASTIC OVER LAPPED PANEL FLANGE #12x 1 1/4" THRU PREPUNCHED HOLES. MASTIC MUST BE SNUG IN CORNERS 6" BACK PLATE SLIDE UNDER PANEL. TAPE MASTIC GUN GRADE MASTIC 11

T-Rib panels can be installed over a variety of substrates and can accomodate most insulation requirements. Continuous horizontal members are required for roof clip attachment and must be spaced to meet loading requirements. The horizontal members must have a flat surface at least as wide as the clip. Two fasteners per clip are required. Because T-Rib is a type of standing seam roof that accommodates thermal movement, the roof panels will not act as a diaphragm for wind design. Therefore, bracing is required to resist wind loads. PLYWOOD CLIP OPEN FRAMING CLIP 30lb. SATURATED FELTS ON PLYWOOD SUBSTRATE ZEE PURLIN VINYL FACED BATT INSULATION RIGID INSULATION AND METAL DECK CLIP ON BEARING PLATE RIGID INSULATION AND WOOD DECKING CLIP ON BEARING PLATE 30lb. SATURATED FELTS ON RIGID INSULATION AND METAL DECK 30lb. SATURATED FELTS ON RIGID INSULATION AND WOOD DECK TUBE STEEL HAT CHANNELS CLIP CLIP TUBE STEEL HAT SECTION PURLIN 12

CLIP SEALANT IN SEAM SEALANT IN SEAM 3/16" x 1" "CHEMSCO" HOLD DOWN CLEAT SET ON 3/16" x 1" "CHEMSCO" HEM PANEL END EAVE TRIM EAVE STRUT ZEE PURLIN 3/16" x 1" "CHEMSCO" HOLD DOWN CLEAT SET ON 3/16" x 1" "CHEMSCO" EAVE TRIM ZEE PURLIN EAVE STRUT HOLD-DOWN STRIP @ 6" o.c. HOLD-DOWN STRIP @ 6" o.c. SLIDING EAVE DETAIL (USE WITH SLIDING VALLEY AND FIXED RIDGE, HIP, AND END WALL DETAILS) FIXED EAVE DETAIL (USE WITH SLIDING RIDGE, HIP, AND END WALL DETAILS) CLIP 1 1/ 2 " SEALANT IN SEAM SEALANT IN SEAM 3/16" x 1" "CHEMSCO" HEM PANEL END EAVE TRIM w' CLEAT ZEE PURLIN EAVE STRUT 3/16" x 1" "CHEMSCO" POP-RIVET EAVE TRIM w' CLEAT ZEE PURLIN EAVE STRUT HOLD-DOWN STRIP HOLD-DOWN STRIP @ 6" o.c. @ 6" o.c. SLIDING EAVE DETAIL (USE WITH SLIDING VALLEY AND FIXED RIDGE, HIP, AND END WALL DETAILS) FIXED EAVE DETAIL (USE WITH SLIDING RIDGE, HIP, AND END WALL DETAILS) CLIP 1 1/ 2 " 3/16" x 1" "CHEMSCO" HEM PANEL END GUTTER STRAP @ 24" o.c. FASTENER @ 24" o.c. 3/16" x 1" "CHEMSCO" GUTTER STRAP @ 24" o.c. FASTENER @ 24" o.c. ZEE PURLIN ZEE PURLIN EAVE STRUT EAVE STRUT @ 6" o.c. @ 6" o.c. BOX GUTTER EAVE TRIM w' CLEAT BOX GUTTER EAVE TRIM w' CLEAT SLIDING EAVE WITH GUTTER DETAIL (USE WITH FIXED RIDGE, HIP, AND END WALL DETAILS) FIXED EAVE WITH GUTTER DETAIL(USE WITH SLIDING RIDGE, HIP, AND END WALL DETAILS) 13

CLIP 7" RIDGE/HIP TRIM PAN PANEL END STAKING FASTENER (1) PER PANEL #12 x 1" SET @ 3" o.c. METAL TOP CLOSURE SET ON 3/16" x 1" "CHEMSCO" 8" x 8" RIDGE/HIP PLATE 20 ga. STEEL ZEE PURLIN FIXED RIDGE/HIP DETAIL (USE WITH SLIDING EAVE AND VALLEY DETAILS) 2" @ 12" o.c. 12" 2" RIDGE TRIM 3/16"x 1" "CHEMSCO" CLIP METAL TOP CLOSURE SET ON 3/16"x 1" "CHEMSCO" @ 3" o.c. #12 SLIDING RIDGE/HIP DETAIL (USE WITH SLIDING EAVE AND VALLEY DETAILS) 2" RIDGE TRIM 12" 2" VENT DRIP CLEAT CLIP METAL TOP CLOSURE SET ON 3/16"x 1" "CHEMSCO" @ 3" o.c. #12 VENTED, FIXED RIDGE/HIP DETAIL (USE WITH SLIDING EAVE AND VALLEY DETAILS) * CLIP SCREWS MUST HAVE LOW- PROFILE HEADS. PURCHASE FROM FABRAL ONLY. 14

CLIP SEALANT IN SEAM #14 FASTENER @ 6" o.c. W' NEOPRENE WASHER 3/16"x 1" "CHEMSCO" ICE & WATER SHIELD ON 16ga. STEEL BACKER VALLEY TRIM FIXED VALLEY DETAIL (USE WITH FIXED EAVE AND SLIDING RIDGE, HIP, AND END WALL DETAILS) * CLIP SCREWS MUST HAVE LOW-PROFILE HEADS. PURCHASE FROM FABRAL ONLY. CLIP SEALANT IN SEAM 3/16" x 1" "CHEMSCO" NOTE: INSTALLER TO FIELD NOTCH AND HEM PANEL END UNDER. 3/ 8 1 1/ 2 " 5" MIN. @ 6" o.c. ZEE PURLIN HOLD-DOWN CLEAT ON 3/16" x 1" "CHEMSCO" ICE & WATER SHIELD ON 16" x 16" VALLEY BACKER VALLEY TRIM SLIDING VALLEY DETAIL (USE WITH SLIDING EAVE AND FIXED RIDGE, HIP, AND END WALL DETAILS) * CLIP SCREWS MUST HAVE LOW-PROFILE HEADS. PURCHASE FROM FABRAL ONLY. 15

CONTINUOUS ANGLE CONTINUOUS HOLD-DOWN CLEAT SCREW RIVET CAULK W/ BUTYL CONTINUOUS ZEE FIELD-BEND PANEL UP AT LEAST 2 1/2" CONTINUOUS SUPPORT (UNNECESSARY FOR INSTALLATIONS OVER DECK) GABLE FLASHING PURLIN PURLIN SCREW GABLE FLASHING CONTINUOUS SUP- PORT (UNNECES- SARY FOR INSTAL- LATIONS OVER DECK) WALL PANEL WALL PANEL START GABLE END GABLE SEALANT TYPICAL REGLET CONTINUOUS HEM; FILL W/ BUTYL CAULK CONTINUOUS SUPPORT (UNNECESSARY FOR INSTALLATIONS OVER DECK) PURLIN SIDEWALL DETAIL SCREW (12" O.C.) BEND UP PANEL 2 1/2"; CAULK SEAM W/ BUTYL RIVET (12" O.C.) EXPANSION JOINT CAP HOLD-DOWN CLEAT BUTYL CAULK OR E E 2E RIVET CONTINUOUS ANGLE E = CALCULATED THERMAL MOVEMENT CONTINUOUS ANGLE EXPANSION JOINT DETAIL RUBBER MEMBRANE CONTINUOUS SUPPORT (UNNECESSARY FOR INSTALLATIONS OVER DECK 16

LOW FIXED CLIP URETHANE SEALANT UNDER COVER RIB COVER CLIP 7" PEAK TRIM METAL TOP CLOSURE SET ON 3/16" x 1" "CHEMSCO" SEALANT PAN PANEL END #12 x 1" SET @ 3" o.c. STAKING FASTENER (1) PER PANEL #12 x 1" SET @ 12" o.c. POP-RIVET 30lb. FELTS ON PLYWOOD SUBSTRATE HOLD-DOWN STRIP PEAK STRUT CLIP ZEE PURLIN FIXED PEAK DETAIL (USE WITH FIXED RIDGE, HIP, AND END WALL DETAILS AND SLIDING EAVE AND VALLEY DETAILS) ROOF/FASCIA TRANSITION (FIXED AT TRANSITION; USE WITH SLIDING RIDGE, HIP, AND PEAK DETAILS AND SLIDING DETAIL AT FASCIA BOTTOM) COUNTERFLASHING PITCHBREAK TRIM 6" METAL TOP CLOSURE SET ON 3/16" x 1" "CHEMSCO" SEALANT TAPE CLIP STAKING FASTENER (1) PER PANEL #12 x 1" SET @ 3" o.c. PEAK STRUT ZEE PURLIN FIXED END WALL DETAIL WITH SURFACE- MOUNTED REGLET (USE WITH SLIDING EAVE AND VALLEY DETAILS) 17

PRE-FAB ROOF CURB CURB ROOF PANEL A A DOWNSLOPE 3/16"x 1" "CHEMSCO" CURB JAMB FLASHING 6" CURB FLASHING (by others) typ. POP-RIVET TO PANEL CURB TRIM 3/16"x 1" "CHEMSCO" TURN PANEL EDGE UP 6" SECTION A-A 30lb. FELTS ON RIGID INSULATION AND METAL DECK 18

C L C L C L VENT PIPE PIPE BOOT SET IN SEALANT SCREW FASTENER @ 3" o.c. VENT PIPE FLASHING (ALSO APPLIES TO LIGHT EQUIPMENT CURBS) LEAVE CLEARANCE OF 2" AROUND PIPE. 2" 2" FOR ATTACHING PIPE BOOTS TO PANELS ON PURLINS, DO NOT PENETRATE PURLINS WITH SCREWS AND KEEP SCREWS AND PIPE AT LEAST 1" FROM PURLINS. NOT TO EXCEED 10" FIELD-CUT PANEL OUTSIDE CORNER FLASHING FILL HEM W/ BUTYL CAULK PANCAKE HEAD SCREW (12" O.C.) NOT TO EXCEED 10" PANCAKE HEAD SCREW (12" O.C.) FILL HEMS W/ BUTYL CAULK INSIDE CORNER FLASHING NOT TO EXCEED 10" NOT TO EXCEED 10" FASCIA INSIDE CORNER NOT TO EXCEED 10" FASCIA OUTSIDE CORNER FIELD-CUT AND HEM PANEL; FILL HEM WITH BUTYL SEALANT FOR VERTICAL FASCIA PANELS LESS THAN 10' LONG, MAKING THE FIRST FOLD ONLY OF THE SEAM IS PERMISSIBLE. CONTINUOUS CLEAT PANCAKE HEAD SCREW (12" O.C.) FASCIA EDGE 19

1 SET 36" WIDE ICE & WATER SHEILD 2 SET 30# FELTS, LAP 6", START AT EAVE 20

3 SET RAKEWALL TRIM WITH J-CLEAT 4 SET VALLEY TRIM WITH CLEATS 21

5 PANELS IN PLACE RIDGE VALLEY GABLE LAP PANELS 12" ROOF TO FASCIA RAKEWALL PITCHBREAK 22

3449 Hempland Road, Lancaster, PA 17601 (800) 477-2741 Route 24 West, Gridley, IL 71744 (800) 451-3974 308 Alabama Blvd., Jackson, GA 30233 (800) 884-4484 Route 3, Box 632, Idabel, OK 74745 (800) 926-8509 2402 Industry Way, Cedar City, UT 84720 (800) 432-2725 658 Boekel Road, Rathdrum, ID 83858 (888) 432-2725 1820 East 26 th St., Marshfield, WI 54449 (800) 528-0878 Highway 41 South & 55 Lamb Loop Road, Tifton, GA 31793 (800) 749-8144 World Wide Web address: www.fabral.com e-mail address: fabinfo@fabral.com 10/01(9832-728) A-900 8 2001 FABRAL