CIA-GEL 000 EPOXY One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY
City of Los Angeles Research Report No. (in Concrete, Block and Brick) City of Los Angeles Research Report No. (in URM) ICC ES ESR 0 NSF Listing Pending One Product for All Applications USP CIA-GEL 000 epoxy is designed to solve numerous applications with one product. CIA-GEL 000 is thick enough to be used in hollow masonry or concrete block. CIA-GEL 000 also is also designed to wet the concrete so that a less viscous product is not necessary for solid concrete applications. Some typical applications are: Rebar doweling into solid or hollow masonry. The use of a screen tube is required for hollow wall applications.. degree combination anchors. Anchoring for seismic retrofit in accordance with City of Los Angeles Division or UCBC Appendix Chapter I. See COLA Report No. and/or ICC-ES ESR-0 for details. Anchoring threaded rod into solid or hollow masonry. The use of a screen tube is Anchoring threaded rod or rebar in concrete brick or block rehabilitation projects. Anchoring vibratory equipment. required for hollow wall applications. Attaching steel angles or ledgers to solid or hollow masonry. The use of a screen tube is required for hollow wall applications. Attaching threaded rod or reinforcing bar into grout filled (solid) concrete block. Attaching threaded rod or reinforcing bar into hollow concrete block. The use of a screen tube is required for hollow wall applications. Threaded rod anchorage into foundation for HD hold down and other types of uplift resisting connectors. Attaching sill plates to concrete. Rebar doweling into concrete. Guard rail anchoring close to edge applications. Support brackets for rail projects. Tilt up wall braces. Crack injection paste. High strength non-pick caulking for security projects. Anchoring for DOT projects. Brick veneer anchoring. Expansion joint anchors. Advantages of CIA-Gel Epoxy 0% solids and solvent free. Moisture insensitive. Achieves Exceptional Holding Strengths. Low odor, low toxicity, non-shrink formulation. Long working time in mixing nozzle. No expansion forces exerted on base material. Easy to use - no setting tools required, no manual mixing required. Clean no contact with the adhesive required. Economical minimal waste, use only the amount you require. Versatile One cartridge can be used with any size threaded rod or rebar for numerous applications. Reliable the static mixing nozzle assures constant mixing.
The is a high strength, moisture insensitive, non-sag epoxy ideally suited for a wide range of applications including structural anchoring, rebar doweling, crack injection of medium to wide cracks in concrete, crack sealing, port placement surface patching and spall repair. GEL- oz. GEL- oz. GEL- oz. GEL- oz. Dispenses with a standard caulking gun, and does not require mixing of entire cartridge for use. AN Air Nozzle with Extension Has / FPT thread for quick disconnect air fittings. HDT- oz. Hand Tool Designed for use with the CIA-Gel oz. epoxy cartridge. Very low hand pressure required to dispense epoxy. Does not require an air compressor. Cost-effectiveness makes these the ideal tools for small jobs. HDT- oz. Hand Tool Similar to the oz. For dispensing oz cartridges. Pneumatic Dispensing Tool Lightweight but rugged construction will give years of service. On demand trigger dispenses epoxy easily and stops the flow of epoxy when released. The oz. tool is equipped with a retract button for power return of the piston plungers making this tool the fastest a nd easiest to use. Extremely well balanced and lightweight tools allow one-handed operation. PDT- oz. PDT- oz. PDT- oz. CNOZ / Mixing Nozzle Static mixing nozzles divide and recombine the epoxy thousands of times while the epoxy is dispensed to insure adequate mixing every time. Additional nozzle diameters available to best suit your application. Concrete Cleanout Brush For cleaning of drilled holes. Available sizes: NB / x NB / x NB x BB Blowout Bulb For blowing of dust and debris from drilled holes.
City of Los Angeles Research Report No. (in Concrete, Block and Brick) City of Los Angeles Research Report No. (in URM) ICC ES ESR 0 NSF Listing Pending Concrete Installation. Drill holes to correct diameter and embedment.. Clean holes with compressed air and concrete cleanout brush. Dust and debris left in the hole will reduce the holding capacity of the anchor.. Remove cartridge cap and D-shaped plugs. Place cartridge in dispensing tool and dispense a small amount of adhesive until both black and white components are being ejected.. Place mixing nozzle and retaining nut over cartridge opening and tighten. Discard a small portion of adhesive to insure proper mixing. Blended epoxy should be consistent gray color. Do not use epoxy which is not blended.. Inject epoxy starting from bottom of hole and slowly withdraw to avoid air pockets.. Slowly push anchor into hole, rotating in a clockwise motion. See chart for initial set, bolt-up, and cure times. Average Ultimate Loads (lbs) for Grade 0 Reinforcing Bar Installed In Stone Aggregate Concrete Using CIA-Gel 000 Epoxy, Rebar Size Hole Diameter (inches) Embedment (inches) Tension 00psi Shear 00psi # /,, # / -/,00,0 # / -/,0,0 # -/,00,00 # -/ -/,0,0 # -/,0, # -/,,0 Average Ultimate Loads (lbs) For Grade B Threaded Rod Installed in Stone Aggregate Concrete Using CIA-Gel Epoxy, Stud Diameter Embedment (inches) Tension 00psi Shear 00psi Tension 000psi / -/,,0, / -/,0,0, / -/,,0, / -/,,,0 / -/,,0, / -/,,00, / -/,,0, / -/,0,, / -/,0,,00,, 0, The tabulated values are average ultimate loads provided by an independent testing agency in accordance with ASTM E requirements. General industry practice is to use a minimum safety factor of : to obtain design loads. It is, however, the responsibility of the design engineer to apply the correct safety factor for the particular application.*see ICC Evaluation Service, Inc., ICC-ES ESR 0 for allowable values and/or conditions of use concerning material presented in this document. It is subject to re-examination, revisions and possible cancelation. Allowable loads can be increased -/% for short term earthquake or wind loads, per applicable building codes. See Adhesives and Anchoring Design Guide and ICC-ES ESR-0 for anchor capacities in additional configurations including; brick, CMU, lightweight concrete, and service conditions such as seismic and wind loading, freeze-thaw, water filled holes, and etc...
City of Los Angeles Research Report No. (in Concrete, Block and Brick) City of Los Angeles Research Report No. (in URM) ICC ES ESR 0 NSF Listing Pending Hollow Masonry or Concrete Block Installations. Drill hole to desired embedment.. Clean hole using compressed air nozzle.. Alternate several times between air and concrete cleanout brush. Air nozzle and concrete cleanout brush should reach to the bottom of the hole for proper cleaning.. Fill screen completely full with epoxy starting from the bottom. Monitor cartridges for leaks out the back end. DO NOT USE CARTRIDGES WHICH LEAK.. Insert screen tube into the hole.. Slowly insert steel sleeve (or rust free threaded rod depending upon application) into screen tube using a clockwise motion. Allow sufficient time (see bolt-up and cure time chart) before loading. Screen Tubes Approximate Fastenings Catalog No. Description Screen Tube Hole/Bit Diameter Use with Rod/ Rebar Diameter CST / X / / / # CST / X / / /# CST / X / / /# CST / X / CST / X / CST / X / CSSLV Steel Sleeves / -- -- oz. oz. Overhead Hole Plugs Catalog No. Description Diameter Hole/Bit Diameter Rod Diameter Rebar HP / Hole plug / / # HP / Hole Plug / / # HP / Hole Plug / / # HP / Hole Plug / / N/A HP Hole Plug / # HP -/ Hole Plug -/ # HP -/ Hole Plug -/ -/ # HP -/ Hole Plug -/ -/ #
HOLE DEPTHS INCHES Anchors Per Cartridge Estimating Guide Bolt Size / / / / / -/ -/ // Hole Size / / / / -/ -/ -/ -/ Cartridge Size (oz) 0 0 0 0 0 0 0 0 Number of anchors is based on exact volumetric calculations, No allowance has been made for bolt or hole deformation, waste or unusual drill bit sizes. Multiply listed values by. to estimate usage for corresponding reinforcing bar sizes. Product Specifications Parameter Part A Color Black Product Epoxy Resin Specific Gravity. ±. Flash Point F/ C Viscosity (Brookfield),000 Shelf Life year minimum Not sensitive to UV light or heat Wet or Damp Applications Mixed Epoxy Heat Deflection Temperature (ASTM D -)... F/ C Compressive Strength (ASTM D M-)..., psi Tensile Strength (ASTM D )...,00 psi Elongation (ASTM D )....% Shore D hardness... 0 Slant/Shear (ASTM C-)...000 psi Meets ASTM C -... Types,, &, Grade... Class B, C, D, E & F Viscosity...,000 CPS @ C Meets AASHTO M Approved for FAA and DOT s Part B White Amine Adduct. ±. >0 F/> C,00 year minimum Cure Times Temperature Initial Set Time (hrs.) Bolt-up Time (hrs.) - - -0 - -0 - >0 > ( F) ( C) 0-0 -0 Cure Time (hrs.) Corporate Office: 0 Southcross, Burnsville, MN Ph: (00) - Fax: () - www.uspconnectors.com www.covertoperationsinc.com USP-0