ChemSet 101 PLUS. Chemical Anchoring - Anchor Studs 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION. Product

Size: px

Start display at page:

Download "ChemSet 101 PLUS. Chemical Anchoring - Anchor Studs 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION. Product"

Aubrey Goodwin
6 years ago
Views:

12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION Product PERFORMANCE RELATED MATERIAL SPECIFICATION INSTALLATION RELATED ChemSet Injection 101 PLUS is a marine grade polyester adhesive.

Suitable for ing into a wide variety of substrates Solid concrete, hollow block and brick Flooded holes Styrene Free Cold and temperate climates VOC Compliant Australian Made Installation Principal

Load should not be applied to until the chemical has sufficiently cured as specified in the following diagrams.

1 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION Product PERFORMANCE RELATED MATERIAL SPECIFICATION INSTALLATION RELATED ChemSet Injection 101 PLUS is a marine grade polyester adhesive. Benefits, Advantages and Features Certified Performance European Technical Approval ETAG Option 7 Fast installation: Load in 50 minutes (at 20 C) Easy cold weather dispensing Versatile: Suitable for ing into a wide variety of substrates Solid concrete, hollow block and brick Flooded holes Styrene Free Cold and temperate climates VOC Compliant Australian Made Installation Principal Applications Hollow brick and block Stadium seating Starter bars Balustrades Installation temperature limits: Substrate: 0 C to 40 C. Adhesive: 5 C to 40 C. Load should not be applied to until the chemical has sufficiently cured as specified in the following diagrams. ETA European Technical Approval ETAG 001 Part 5 Option 7 Galvanised And Stainless Steel Anchors ETA-13/ CPD Service temperature limits: -40 C to 80 C Drill recommended diameter and depth hole. 2. Important: Use Ramset Dustless Drilling System to ensure holes are clean. Alternatively, clean dust and debris from hole with stiff wire or nylon brush and blower in the following sequence: blow x 4, brush x 3, blow x 4, brush x 3, blow x Insert mixing nozzle to bottom of hole. Fill hole to 3/4 the hole depth slowly, ensuring no air pockets form. 4. Insert Ramset /rebar to bottom of hole while turning. 5. ChemSet Injection to cure as per setting times. 6. Attach fixture. Substrate Temperature Setting Times 30 C 25 C 20 C 10 C 5 C Gel Time (mins) 101 PLUS Loading Time (mins) Note: Cartridge temperature minimum 5 C RAMSET

2 CHEMICAL INJECTION ANCHORING Installation and performance details: ChemSet Injection 101 PLUS and s Anchor size, d b (mm) Drilled hole diameter, d h (mm) Fixture hole diameter, d f (mm) Anchor effective depth, h (mm) Tightening torque, T r (Nm) Edge distance, e c (mm) Optimum dimensions* Anchor spacing, a c (mm) Concrete substrate thickness, b m (mm) M M M M M M * Note: For shear loads acting towards an edge or where these optimum dimensions are not achievable, please use the simplified strength limit state design process to verify capacity. Anchor Size, d b (mm) Reduced Characteristic Capacity# Grade 5.8 Steel Studs Grade 8.8 Steel Studs AISI 316 Stainless Steel Studs Concrete Tension, ØN uc (KN)** Shear, ØV us Tension, ØN us Shear, ØV us Tension, ØN us Shear, ØV us Tension, ØN us Concrete Compressive Strength, f' c (kn) (kn)*** (kn) (kn)*** (kn) (kn)** 20 MPa 32 MPa 40 MPa M M M M M M * Note: For shear loads acting towards an edge or where these optimum dimensions are not achievable, please use the simplified strength limit state design process to verify capacity. **Note: Reduced characteristic ultimate concrete tensile capacity = ØN uc where Ø = 0.6 and N uc = Characteristic ultimate concrete tensile capacity. For conversion to Working Load Limit MULTIPLY ØN uc x 0.55 ***Note: Reduced characteristic ultimate steel tensile capacity = ØN us where Ø = 0.8 and N us = Characteristic ultimate carbon steel tensile capacity. For conversion to Working Load Limit MULTIPLY ØN us x 0.45 #Note: Design Tensile Capacity ØN ur = minimum of ØN uc and ØNus WET HOLES: Multiply ØN uc x DESCRIPTION AND PART NUMBERS Description Cartridge Size Part No. Cartridge 380 ml C101C Jumbo Cartridge 750 ml C101J Kit 2 x 380 ml ISKP Mixer Nozzle for 101 PLUS ISNP Effective depth, h (mm) Preferred h = h n otherwise, h = L e - t h 6 * d h t = total thickness of material(s) being fastened. Substrate thickness, bm (mm) b m = greater of: 1.25 x h, h + (2 x d h ) Drilled hole depth, h 1 (mm) h 1 = h h = Effective depth 12.3 ENGINEERING PROPERTIES Refer to Engineering Properties for s on page RAMSET

3 STEP 1 Design tensile action effect, N* (kn) Select to be evaluated Table 1a Indicative combined loading interaction diagram Notes: ~ Shear limited by Grade 5.8 steel capacity. ~ Tension limited by concrete capacity using nominal depths. ~ No edge or spacing effects. ~ f' c = 32 MPa M12 M10 M8 M16 M20 M Design shear action effect, V* (kn) Table 1b Absolute minimum edge distance and spacing values, e m and a m (mm) e m, a m Step 1c Calculate effective depth, h (mm) Refer to Description and Part Numbers table for either s on page 43. Effective depth, h (mm) Preferred h = h n otherwise, h = L e - t h 6 * d h t = total thickness of material(s) being fastened. 1 Anchor size determined, absolute minima compliance achieved, effective depth (h) calculated RAMSET

4 STEP 2 Verify concrete tensile capacity - per Table 2a Reduced characteristic ultimate concrete tensile capacity, ØN uc (kn), Ø c = 0.60, f c = 32 MPa Drilled hole dia., d h (mm) Effective depth, h (mm) Bold values are at nominal depths. Note: Effective depth, h must be 6 x drilled hole diameter, d h for to achieve tabled shear capacities. WET HOLES: Multiply ØN uc x 1 Table 2b Concrete compressive strength effect, tension, X nc f c (MPa) X nc Table 2c Edge distance effect, tension, X ne Edge distance, e (mm) Table 2d Anchor spacing effect, end of a row, tension, X nae For single design, X nae = 1.0 Anchor spacing, a (mm) RAMSET

5 2 STEP 3 Table 2e Anchor spacing effect, internal to a row, tension, X nai For single design, X nai = 1.0 Anchor spacing, a (mm) Design reduced ultimate concrete tensile capacity, ØN urc ØN urc = ØN uc * X nc * X ne * ( X nae or X nai ) Verify tensile capacity - per Table 3a Reduced characteristic ultimate steel tensile capacity, ØN us (kn), Ø n = 0.8 Grade 5.8 Carbon Steel A4/316 Stainless Steel Typical Threaded Rod Grade 8.8 Carbon Steel Step 3b Reduced characteristic ultimate bolt steel tensile capacity, ØN tf (kn) Not appropriate for this product. Design reduced ultimate tensile capacity, ØN ur ØN ur = minimum of ØN urc, ØN us Check N* / ØN ur 1, if not satisfied return to step 1 Tensile performance conversion table Performance Required Concrete Tensile Performance Notation Concrete Tension Capacity NOTE: Design Tensile Capacity is the minimum of Concrete Tension and Steel Tension Capacities Notation Steel Tensile Performance Carbon Steel Tension Capacity Stainless Steel Tension Capacity Strength Limit State ØN urc MULTIPLY ØN urc x 1.00 ØN us MULTIPLY ØN us x 1.00 MULTIPLY ØN us x 1.00 Working Load Limit N ac MULTIPLY ØN urc x 0.55 N as MULTIPLY ØN us x 0.45 MULTIPLY ØN us x 0.50 Cyclic Loading Refer to page 40 for suitable Refer to page 40 for suitable Refer to page 40 for suitable N yc N ys Fire Resistance N Rk,c,fi,t Refer to pages N Rk,s,fi,t Refer to pages Refer to pages Cracked Concrete/Tension Zone N 0 Rd,p Refer to pages N Rd,s Refer to pages Refer to pages Seismic N 0 Rd,p,sis Refer to pages N Rd,s,sis Refer to pages Refer to pages RAMSET

6 STEP 4 Verify concrete shear capacity - per Table 4a Reduced characteristic ultimate concrete edge shear capacity, ØV uc (kn), Ø q = 0.6, f c = 32 MPa Edge distance, e (mm) Note: Effective depth, h must be 6 x drilled hole diameter, d h for to achieve tabled shear capacities. Table 4b Concrete compressive strength effect, concrete edge shear, X vc f c (MPa) X vc Load direction effect, conc. edge shear, X vd Table 4c Load direction effect, concrete edge shear, X vd Angle, X vd Table 4d Anchor spacing effect, concrete edge shear, X va Note: For single designs, X va = 1.0 Edge distance, e (mm) Anchor spacing, a (mm) RAMSET

7 e 1 Concrete edges Shear Force e 2 ANCHOR AT A CORNER Failure wedge Table 4e Multiple s effect, concrete edge shear, X vn Note: For single designs, X vn = 1.0 Anchor spacing / Edge distance, a / e Number of s, n Table 4f Anchor at a corner effect, concrete edge shear, X vs Note: For e 1 /e 2 > 1.25, X vs = 1.0 Edge distance, e 2 (mm) Edge dustance, e 1 (mm) STEP 5 Design reduced ultimate concrete edge shear capacity, ØV urc ØV urc = ØV uc * X vc * X vd * X va * X vn * X vs Verify shear capacity - per Table 5a Reduced characteristic ultimate steel shear capacity, ØV us (kn), Ø v = 0.8 Grade 5.8 Carbon Steel A4/316 Stainless Steel Typical Threaded Rod Grade 8.8 Carbon Steel Step 5b Reduced characteristic ultimate bolt steel shear capacity, ØV sf (kn) Not appropriate for this product RAMSET

8 5 Shear performance conversion table Performance Required Design reduced ultimate shear capacity, ØV ur ØV ur = minimum of ØV urc, ØV us Check V* / ØV ur 1, if not satisfied return to step 1 Concrete Shear Performance Notation Concrete Shear Capacity NOTE: Design Shear Capacity is the minimum of Concrete Shear and Steel Shear Capacities Notation Steel Shear Performance Carbon Steel Shear Capacity Stainless Steel Shear Capacity Strength Limit State ØV uc MULTIPLY ØV uc x 1.00 ØV us MULTIPLY ØV us x 1.00 MULTIPLY ØV us x 1.00 Working Load Limit V ac MULTIPLY ØV uc x 0.55 V as MULTIPLY ØV us x 0.50 MULTIPLY ØV us x 0.52 Cyclic Loading Refer to page 40 for suitable Refer to page 40 for suitable Refer to page 40 for suitable V yc V ys Fire Resistance V Rk,c,fi,t Refer to pages V Rk,s,fi,t Refer to pages Refer to pages Cracked Concrete/Tension Zone V 0 Rd,c Refer to pages V 0 Rd,s Refer to pages Refer to pages Seismic V 0 Rd,c,sis Refer to pages V 0 Rd,s,sis Refer to pages Refer to pages STEP 6 6 Combined loading and specification Check N*/ØN ur + V*/ØV ur 1.2, if not satisfied return to step 1 Specify Threaded Stud Anchors Ramset ChemSet Injection 101 PLUS with (Anchor Size) grade 5.8 ((Anchor Stud Part Number)). ). Drilled hole depth to be (h) mm. Example Ramset ChemSet Injection 101 PLUS with M16 grade 5.8 (CS16190). Drilled hole depth to be 125 mm. To be installed in accordance with Ramset Technical Data Sheet RAMSET

ChemSet 101 PLUS. Chemical Anchoring - Reinforcing Bar Anchorage 20.1 CHEMICAL INJECTION ANCHORING 20.1 GENERAL INFORMATION.

ChemSet 101 PLUS. Chemical Anchoring - Reinforcing Bar Anchorage 20.1 CHEMICAL INJECTION ANCHORING 20.1 GENERAL INFORMATION. 20.1 CHEMICAL INJECTION ANCHORING 20.1 GENERAL INFORMATION Product ChemSet Injection 101 PLUS is a marine grade polyester adhesive anchor. Benefits, Advantages and Features Certified Performance European