Description PercoTop Primer 010 is a solvent borne zinc chromate-free 1K primer. Composition based on polyvinyl butyral. Products CS310/CS311/CS312/CS313/CS315/CS316 CS010-CS095 CS600 PercoTop Tints PercoTop Thinner Standard Colours CS310: ca RAL 7035. CS311: ca RAL 6011. CS312: ca RAL 9010. CS313: ca RAL 9005. CS315: colourless. CS316: ca RAL 1015 Properties Very fast drying. Very good adhesion on metal substrates as listed below. Provides a very fine and smooth surface. Indoor use without warm-humid or wet conditions. Substrates Steel, aluminium and non-ferrous metal. Galvanic and sendzimir zinc coated steel. 1/5
Surface preparation Substrates must be free from all contaminants. Because of the wide variety of substrates and their manufacturing processes, a preliminary test should be carried out on the respective substrate to ensure that the pretreatment is sufficient to guarantee a perfect adhesion. For information on substrate and respective surface preparation, refer to the supplier s specifications. VOC value ready for use (EU Directive 1999/13/EC) RAL 9010: 706 g/l 25 % CS600 inclusive. RAL 9005: 711 g/l 25 % CS600 inclusive. 2/5
Product preparation Thinner Recommended dry film thickness CS600 20-30 µ Application Gravity feed Application viscosity Thinner Spray nozzle Pressure Number of coats DIN 4 at 20 C (s) (%) (mm) (bar) 18-20 25-30 1.3-1.4 3.0-4.0 2 Suction feed (High pressure spraying) HVLP 18-20 25-30 1.3-1.4 2.0-2.5 2 (Low pressure spraying) Airless 30-35 10-15 0.28 2.0-3.0 air 1-2 Airmix Ca 100 Pressure pot 18-20 25-30 1.1 2.5-3.5 air 2 Membrane pump (High pressure spraying) Electrostatic 1.0-2.0 According to the advice of the DuPont Technical Representative. 3/5
Drying Air drying at 20 C Dust dry Dry to handle Dry to recoat Dry 25 µ dry film thickness 10 minutes 15 minutes 30 minutes 30 minutes Forced drying Drying time Drying temperature Flash time: 5 minutes. Depending on film thickness. 10 minutes 60 C object temperature Recoatability Recoatable Remarks With PercoTop and Imron topcoats. Recoating with above mentioned products without sanding is possible. Product data Package viscosity 60-80 s DIN 4 Flash point 25 C Solids Density Theoretical coverage Theoretical consumption (at 25 µ) (at 25 µ) Weight (%) (kg/l) (m 2 /kg) (g/m 2 ) +/- 1 +/- 0.01 White Packaged 43.4 1.14 8.1 123 Black Packaged 42.8 1.14 7.9 126 4/5
Remarks Stir before use. Storage Conditions Shelf life at 5 C to 35 C Material has to be stored at a temperature between 5 C and 35 C. Refer to the label on the original can. Safety Consult the Safety Data Sheet prior to use. Observe the precautionary notices displayed on the container. Information The information provided herein corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific designated; these data may not be valid for such used in combination with any other s or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. This Technical Data Sheet supersedes all previous issues. Copyright 2011 DuPont. All rights reserved. The DuPont Oval Logo, DuPont, The miracles of science and all products denoted with or are registered trademarks or trademarks of E. I. du Pont de Nemours and Company or its affiliates 5/5