SERIES 00 AN-2- Series 00 butterfly valve with 0 position lever lock Used in commercial grooved-end piping systems 2" through 2". The uniqueness of the Series 00 ruvlok begins with the spherical bore of the disc seat area. This facilitates a constant DISC-TO-SEAT loading that maintains a leak tight stem seal regardless of disc position. The stem sealing force is constant through the full disc cycle and operating torques are kept low which increases valve life. The design provides a bubble tight seal from full vacuum to 00 psi when the valve is closed. The valve is rated for dead-end service to a full pressure rating of 00 psi. Silicone Free Series 00 available upon special request. NSF/ANSI 6 AN-22- Series 00 butterfly valve with gear operator The stem-to-disc connection provides zero backlash. The high strength, corrosion resistant, stainless steel stems are blow-out proof. Each stem is fitted with a secondary seal that also provides a lifetime lubrication chamber. The Series 00 valve is designed with the contractor in mind. The valve body is a rugged one-piece casting with an integral mounting base for gear operator or handle actuation, while providing room for a minimum of 2" of pipe insulation. The valve is designed and manufactured to meet or exceed the requirements of MSS SP-6. For data on fire protection listings/approvals, contact your Anvil representative. 2" - 0" Series 00 Certified to NSF/ANSI 6 (cold water) and Annex LEAD FREE Project: Address: Contractor: Engineer: Submittal Date: Notes : Notes 2: L-8.4 PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:
SERIES 00 MATERIAL SPECIFICATIONS. BODY: Ductile Iron conforming to ASTM A 56, rade 65-45-2 Body Coating: Nylon (For nylon coating resistance, see table on page 8.) 2. DISC: Ductile Iron conforming to ASTM A 56 rades 65-45-2 Disc Encapsulation: Properties as specified in accordance with ASTM D 2000. rade E (EPDM): Service Temperature Range -40 F to +20 F (-40 C to +0 C) Recommended for water service, dilute acids, alkalies, oil-free air and many chemical services. NOT FOR USE IN PETROLEUM SERVICES. rade T (Nitrile): Service Temperature Range -20 F to +80 F (-2 C to +82 C) Recommended for petroleum products, air with oil vapors, vegetable oils and mineral oils. NOT FOR USE IN HOT WATER SERVICES., 4. UPPER AND LOWER SHAFT: Type 46 Stainless Steel 5. O-RINS: Compatible with disc coating 6,. TOP AND BOTTOM BRONZE SLEEVE BUSHINS: 8", 0", & 2" only 6 5 2 5 4 RUVLOK BUTTERFLY VALVE SERIES 00 (ORDERIN INFORMATION) Sample Part Number 8" AN2- > 8" A N 2 - Special Body Style Body Coating Series Disc Coating Operator Stem 2" - 2" A N - Nylon -XX - Nitrile (rade T) 0 - None - 46 S.S. SF - Manufactured 2 - EPDM (rade E) - 0 Pos. L/Lock 2 - ear Operator D - Infinite Pos. w/memory Stop 4 - Short 0 Pos. L/lock Operator without Silicone NOTE: For operator safety, hand levers on 8" valves are limited to applications with a 25 PSI (. bar) maximum pressure. For operator safety, hand levers on 0" and 2" valves are not available. L-.6
SERIES 00 Dimensions SERIES 00 BUTTERFLY VALVE DIMENSIONS Note: " or 5" handwheels may be included on valves sizes 2" - 4". Contact your Anvil Rep. for additional information. (ANSI/DN) 2 2 4 5 6 8 0 2 In./mm 50 65 80 00 25 50 200 250 00 2 8 2 8 4 5 6 5 8 8 5 8 0 2 In./mm 60..0 88. 4. 4. 68. 2. 2. 2. A 4 5 8 5 5 5 6 6 8.0 6.8 6.8. 4.6 4.6.4 58.8 65. B 4 5 5 6 5 8 5.4 80.8 6.5 08.5 26.5 8. 5.8 202. 22.4 C 4 4 8 5 5 8 5 8 6 8 0 05.. 2.0 6. 4.4 6.8 6. 240. 266. D 5 8 5 8 5 8 26. 26. 26. 26. 26. 26. 4. 4. 4. E......... F 5 5 5 6.2 6.2 6.2 6.2 6.2 6.2 2.0 2.0 2.0 8 8 4. 4. 4. 4. 22.2 22.2 25.4.8.8 H.......5.5.5 J - - - - - 8 8 8 2 - - - - -. 4.8 4.0 0. K 5 5 5 6.2 6.2 6.2 6.2 6.2 6.2 2.0 2.0 2.0 L 5 5 5 6 6 - - 5. 40.5 58.2 65. 8.6.0 240. - - M 0 0 0 0 0 0 5 - - 266. 266. 266. 266. 266. 266. 8.0 - - N 8 8 0 4 5 6 5 8 20 8.0 20. 22. 228. 24.4 25..2 422. 525. P 4 4 4 4 4 4 8 8 5 8 02. 02. 02. 02. 02. 02. 204.5 204.5 25.4 R 2 5 2 5 2 8.2 8.2 8.2 8.2 8.2 8.2 58.5 58.5 65.5 S 2 2 2 2 2 2 2 5 8 2 5 8 5.0 5.0 5.0 5.0 5.0 5.0 66.0 66.0 8.0 T 6 5 6 5 6 5 6 5 6 5 6 5 0 0 60. 60. 60. 60. 60. 60. 25. 25. 50. U 5 5 5 5 5 5 2 2 8 2.0 2.0 2.0 2.0 2.0 2.0 04.8 04.8 45.2 L-6.
SERIES 00 Performance Data Maximum Working Pressure Rating: 00 PSI (Commercial Applications - s 2" thru 2") In./mm In./mm CV VALUES Disc Position (degrees open) 25 0 40 50 60 0 80 0 2 2.5 4 44 48 80 58 50 60. 0. 0.5..0. 5.5. 0. 2 2.85 4 4 8 84 42 6 280 65.0 0.6.0 2. 5.4 5.8.8.5..500 4 20 50 2 28 25 285 400 80 88..0.4.4. 8.8 4.8. 2.6 4 4.500 2 4 00 2 250 420 582 826 00 4. 2.0 2.8 6. 6.5.2 2.0 40. 5.0 5 5.56 62 6 82 45 445 80,00,480 25 4. 4. 5.2 2.5 28.6 0. 5.8 5.8 02.0 6 6.625 6 4 25 55 80,0,20 2,68 50 68. 6.6. 22.4 52. 55.8 4.5 2.4 84.6 8 8.625 2 252 52,65,460 2,40,40 4,8 200 2...4 40.8 4. 00. 6.5 25. 2. 0 0.50 20 28 2,825,62,260 4,50 6,4 250 2. 5. 22.6 54.6 25.8 5. 224.8 6.5 44.4 2 2.50 48 604,440,50,50 5,80 8,50,4 00 2. 28.8 4.6. 2.0 24.5 42. 60. 82. HEADLOSS EQUIVALENT LENTH OF PIPE Equivalent Feet of Pipe* C=20 Sch. 0 Sch. 0 Sch. 40 Max. Insulating Thickness In./mm In./mm Ft./m In./mm 2 2.5 5.8-4. 2 50 60..8 -.4 50 2 2.85 5. -. 2 65.0.6 -. 65.500.6 -.2 2 80 88. 2. - 2.2 50 4 4.500.5-5. 2 00 4. 2. -. 65 5 5.56.0-5.6 2 25 4. 2. -. 65 6 6.625 6. - 4.8 2 50 68.. -.5 65 8 8.625 6. 5. - 2 200 2... - 65 0 0.50. 0.2-250 2..4. - 80 2 2.50 8.4.4-00 2. 2.6 2. - 0 * The equivalent feet of pipe is based on the Hazen and Williams formula and the flow rates typically used with each size valve. VALVE WEIHT AND TORQUE VALUES 5.0 PRESSURE DROP (PSI) VS. (PM) * Approx. Wt. Ea. Operating Pressure 50 PSI 00 PSI 50 PSI 200 PSI 00 PSI In./mm In./mm Lbs./Kg Breakaway Torque (In. - Lbs) / N-m 2 2.5 5 2 0 00 20 200 50 60. 2. 8. 0.2..6 22.6 2 2.85 0 05 26 44 62 250 65.0 4.5. 4.2 6. 8. 28.2.500 26 68 5 425 80 88. 5.0 4.2 5..0 22.0 48.0 4 4.500 5 265 285 20 55 800 00 4. 6.8 2. 2.2 6.2 40. 0.4 5 5.56 20 4 58 65 64 850 25 4..0 55.5 65. 6.5 6.2 6.0 6 6.625 46 625 68 60 820,650 50 68. 20. 0.6 6.6 85. 2. 86.4 8 8.625 68,0,400,640,60,200 200 2. 0.8 2.2 58.2 85. 8. 6.6 0 0.50 8,0 2,5 2,860,00 6,000 250 2. 5.4 28. 268.4 2.2 50. 68.0 2 2.50 2,00,420 4,60 5,600,000 00 2. 4. 2. 86.4 5. 62.8,242. NOMINAL PRESSURE DROP IN POUNDS PER SQUARE INCH (PSI) 4.0.0 2.0.0 0. 0.8 0. 0.6 0.5 0.4 0. 0.2 2 INCH VALVE 2 /2 INCH VALVE INCH VALVE 4 INCH VALVE 5 INCH VALVE 6 INCH VALVE 8 INCH VALVE 0 INCH VALVE 2 INCH VALVE These values are valid for water and lubricating fluid service only. Contact Anvil for information on torques for dry and non-lubricating fluid service. * Weights may vary based on valve options selected. 0. 00 200 00 400 500 00 000 2000 000 4000 5000 000 0000 FLOW RATE IN ALLONS PER MINUTE (PM) L-.4
SERIES 00 Resistance to various chemicals, as a function of temperature F (Fahrenheit) NYLON COATIN Coating Condition after 8 months immersion 68 F 04 F 40 F 6 F Alcohols benzyl alcohol L P P P butanol *** L P ethanol (pure) *** L glycerine (pure) L P glycol P methanol (pure) *** L P Chlorinated solvents carbon tetrachloride P methyl bromide P methyl chloride P perchloroethylene L trichloroethane L P trichloreothylene L Phenols P P P P Various Organic Compounds anethole carbon disulphide *** L** P diacetone alcohol *** L P dimethyl formamide L ethylene chlorhydrin P P ethylene oxide L P furfurol *** L P glucose tetraethyl lead tetrahydrofurare L Salts, esters, ethers amyl acetate L butyl acetate L diethyl ether dioctylphosphate L dioctylphthalate L ethyl acetate fatty acid esters methyl acetate methyl sulfate L tributylphosphaate L tricresylphosphate L Various Products beer cider crude petroleum *** diesel fuel *** fruit juices fuel-oil greases ground nut oil high octane gasoline *** kerosene (paraffin) *** linseed cake milk mustard normal gasoline *** oils 68 F 04 F 40 F 6 F Various Products (cont d.) solutions or emulsions of D.D.T. or lindane hudroxy-quinoline (agricultural sprays) soap solution stearin solvent naptha *** natural gas turpentine *** vinegar wine Inorganic Acids chromic acid (0%) P P P P hydrochlorhic acid (%) L P P hydrochlorhic acid (0%) L P P nitric acid (all concentrations) P P P P phosphoric acid (50%) L P P sulphuric acid (%) L L P sulphuric acid (0%) L P P sulphur trioxide L P P P Other Inorganic products agriculture sprays bleach solutions L P P P bromine P P chlorine P P P P fluorine P P P P hydrogen hydrogen peroxide (20 volumes) L mercury oxygen L P ozone L P P P potassium permanganate (5%) P P sea water soda water sulphur water L Aldehydes & Ketones acetaldehyde L P acetone *** L P benzaldehyde L P cyclohexanone L P formaldehyde (technical grade) L P methylethylketone (MEK) L P methylethylketone (MIBK) L P Hydrocarbons acetylene benzene *** L butane cyclohexane L decaline L HFA (Forane ) hexane methane naphthalene L propane styrene *** 68 F 04 F 40 F 6 F Hydrocarbons (cont d.) tulene *** L L xylene *** L L Inorganic Bases ammonium hydroxide (concentrated) ammonia (liquid or gas) lime-wash potassium hydroxide (50%) L P P sodium hydroxide (5%) L sodium hydroxide (0%) L L sodium hydroxide (50%) L P P Organic acids & anhydrides acetic acid L P P P acetic anhydrie L P P P citric acid L P formic acid P P P P lactic acid L oleic acid L oxalic acid L P picric acid L P P P tartaric acid (saturated solution) L uric acid L Inorganic Salts alum aluminium sulphate ammonium nitrate barium chloride calcium arsenate (concentrated solutions or slurries) calcium chloride calcium sulphate L copper sulphate diammonium phosphate L magnesium chloride (50%) potassium ferrocyanide potassium nitrate * L* P P potassium sulphate sodium carbonate L P sodium chloride (saturated) sodium silicate sodium sulphide L L trisodium phosphate Organic bases aniline (pure) L P P P diethanolamine (20%) *** *** L pyridine (pure) L P P P urea L L LEEND * = Slight Yellowing ** = Yellowing *** = Swelling observed = ood L = Limited P = Poor L-.6