High Temperature (230 ) High Precision Thin ilm Wraparound hip Resistor rrays, Sulfur Resistant PRHT arrays can be used in most applications requiring a matched pair (or set) of resistor elements at very high temperature up to 230. The networks provide 2 ppm/ TR tracking, a ratio tolerance as tight as 0.05 % and outstanding stability. They are available in pitch: 1.00 mm for PRHT 100 (based on case 0603) 1.35 mm for PRHT 135 (based on case 0805) 1.82 mm for PRHT 182 (based on case 16) TURS Tight TR (10 ppm/ ) and TR tracking (to 2 ppm/ ) 2 to 4 resistors (same or different values) Ratio tolerance to 0.05 % Gold terminations for temperature up to 230 vailable High temperature (230 ) Sng terminations for temperature up to 0 vailable SM wraparound chip resistor array Thin film technology Very low noise < -35 d and voltage coefficient < 0.01 ppm/v Sulfur resistant (per STM 809-95 humid vapor test) Material categorization: or definitions of compliance please see www.vishay.com/doc?99912 TYPIL PRORMN TRKING TR 10 ppm/ 2 ppm/ TOL. % 0.05 % IMNSIONS Independent resistors IM. PRHT 100 (0603 base) PRHT 135 (0805 base) PRHT 182 (16 base) mm mil mm mil mm mil 1.52 60 1.91 75 3.06 1 = N x (± 0.2 mm) = N x (± 8 mil) One common point 27 27 27 0.38 3 15 0.38 3 15 0.40 3 16 Suggested land pattern (according to IP-7351) 1 40 1.35 53 1.825 72 0.7 27.6 1.05 41.4 1.525 60 G min. 0.49 19.3 0.88 34.5 1.99 78.3 X max. 0.66 26 1.01 39.8 1.49 58.7 Z max. G min. X max. Z max. 2.57 101.2 2.96 116.5 4.11 161.8 Revision: 23-pr-14 1 ocument Number: 53057
GLOL PRT NUMR INORMTION (1) New Global Part Numbering: PRHT100I4-1K00WGT P R H T 1 0 0 I 4-1 K 0 0 W G T GLOL MOL PRHT 100 PRHT 135 PRHT 182 ONIG. I: Independent : ommon NUMRS O RSISTORS 2 to 4 ecimal R or K VLU (2) S. TOL. TOL. TRMINTION (3) PKGING = % = 1 % = 0.1 % = 0.1 % W = 0.05 % N: Sng over nickel barrier G: Gold over nickel barrier W = Waffle pack, 100 min., 1 mult Tape and Reel: T: 100 min., 1 mult T: 100 min., 100 mult T: 250 min., 250 mult T: 500 min., 500 mult T: 1000 min., 1000 mult T: 2500 min., 2500 mult T: ull tape N and G: Lead (Pb)-free/RoHS version Notes (1) Part number can only have 18 digits. epending on infomation needed a compromise has to be found. codification can be used to identify case size + configuration and number of resistors. See table below..g. PRHT100I4-4K75WGT (Part number has more than 18 digts): PRHT100I4 must be replaced by PRHT17 = PRHT17-4K75WGT (2) When the last digit(s) of the ohmic value is (are) 0, it (they) can be omitted..g.: PRHT100I4-2KWGT can be ordered under PRHT100I4-2K2WGT PRHT100I4-1K00WGT can be ordered under PRHT100I4-1KWGT (3) N termination for temperature up to 0. G termination for temperature up to 230. OIITION O SIZ + ONIGUTION + NUMR O RSISTORS O 18 O 40 O 18 O 40 O 18 O 40 O 18 O 40 O 18 O 40 1 PRHT073I2 15 PRHT100I2 29 PRHT182I2 43 PRHT0742 57 PRHT1352 2 PRHT073I3 16 PRHT100I3 30 PRHT182I3 44 PRHT0743 58 PRHT1353 3 PRHT073I4 17 PRHT100I4 31 PRHT182I4 45 PRHT0744 59 PRHT1354 4 PRHT073I5 18 PRHT100I5 32 PRHT182I5 46 PRHT0745 60 PRHT1355 5 PRHT073I6 19 PRHT100I6 33 PRHT182I6 47 PRHT0746 61 PRHT1356 6 PRHT073I7 PRHT100I7 34 PRHT182I7 48 PRHT0747 62 PRHT1357 7 PRHT073I8 21 PRHT100I8 35 PRHT182I8 49 PRHT0748 63 PRHT1358 8 PRHT074I2 22 PRHT135I2 36 PRHT0732 50 PRHT1002 64 PRHT1822 9 PRHT074I3 23 PRHT135I3 37 PRHT0733 51 PRHT1003 65 PRHT1823 10 PRHT074I4 24 PRHT135I4 38 PRHT0734 52 PRHT1004 66 PRHT1824 11 PRHT074I5 25 PRHT135I5 39 PRHT0735 53 PRHT1005 67 PRHT1825 12 PRHT074I6 26 PRHT135I6 40 PRHT0736 54 PRHT1006 68 PRHT1826 13 PRHT074I7 27 PRHT135I7 41 PRHT0737 55 PRHT1007 69 PRHT1827 14 PRHT074I8 28 PRHT135I8 42 PRHT0738 56 PRHT1008 70 PRHT1828 STNR LTRIL SPIITIONS MOL SIZ Notes (4) t +215 (5) t -40 to +215 RSISTN RNG POWR RTING PR RSISTOR (4) W TOLRN ± % TOLRN % TR (5) ± ppm/ TR (5) ± ppm/ PRHT 100 100 10 to 250K 0.010 0.1,, 1 0.05, 0.1 15 2 PRHT 135 135 10 to 500K 0.0125 0.1,, 1 0.05, 0.1 15 2 PRHT 182 182 10 to 2M 0.0 0.1,, 1 0.05, 0.1 15 2 Revision: 23-pr-14 2 ocument Number: 53057
LIMTI SPIITIONS Operating temperature range -55 to +215 Storage temperature range -55 to +230 PRORMN VS. HUMI SULUR VPOR Test conditions Test results PKGING Several types of packaging are available: Waffle-pack and tape and reel. SIZ PR100 x 2 RTING 50 ± 2, 85 % % RH, exposure time 500 h Resistance drift < (0.05 % R + 0.05 ), no corrosion products observed NUMR O PIS PR PKG WL PK TP N RL MOQ MX. QUNTITY PR OX MIN. MX. 100 PR100 x 3 140 PR100 x 4 60 PR135 x 2 140 PR135 x 3 100 60 PR135 x 4 60 PR182 x 2 60 PR182 x 2 60 PR182 x 2 50 350 MHNIL SPIITIONS Substrate lumina Technology Thin ilm ilm Nickel chromium with mineral passivation N type: Sng over nickel barrier Terminations (1) G type: Gold over nickel barrier Note (1) N terminations for temperatures up to 0. G terminations for temepratures up to 230. PRORMNS TST Noise Voltage coefficient Limiting voltage PKGING RULS PRHT 100 PRHT 135 PRHT 182 SPIITIONS -35 d 0.01 ppm/v 50 V 100 V 150 V Waffle Pack an be filled up to maximum quantity indicated in the table here above, taking into account the minimum order quantity. When quantity ordered exceeds maximum quantity of a single waffle pack, the waffle packs are stacked up on the top of each other and closed by one single cover. To get not stacked up waffle pack in case of ordered quantity > maximum number of pieces per package: Please consult for specific ordering code. Tape and Reel an be filled up to maximum quantity indicated in the table here above, taking into account the minimum order quantity. When quantity ordered is between the MOQ and the maximum reel capacity, only one reel is provided. When several reels are needed for ordered quantity within MOQ and maximum reel capacity: Please consult for specific ordering code. RT POWR IN % 300 250 0 150 100 50 0 0 50 100 150 0 250 MINT TMPRTUR IN MRKING On the primary package, printed information includes Vishay S.. trademark series and model, schematic number of resistors, ohmic value, absolute tolerance, ratio tolerance, type of termination: tinned over nickel barrier. Marking on parts: 8 7 1 2 R1 R2.g.: Ohmic value 13K: oded 1302: M = 1, = 3, = 0, U = 2 M 6 5 U 3 4 R3 R4 Revision: 23-pr-14 3 ocument Number: 53057
PRORMN TSTS ONITIONS RQUIRMNTS PR (Typical Values) RITS Overload 2.5 Un/2 s 0.05 % Rn + 0.05 0.01 % Rn limatic sequences -55 to +155 /5 moisture cycles 0.1 % Rn + 0.05 0.01 % Rn Thermal shock -55 to +155 /5 cycles 30' 0.05 % Rn + 0.05 0.01 % Rn Load life 1000 h/pn at 215 % Rn 0.25 % Rn 8000 h/pn at 215 0.7 % Rn 0.4 % Rn Resistance to solder heat 260 /10 s 0.05 % Rn + 0.05 0.01 % Rn Moisture resistance 0.01 Pn at +40 93 % RH 0.1 % Rn + 0.05 0.01 % Rn High temperature storage 1000 h/no load at +155 0.1 % Rn + 0.05 0.02 % Rn Note Rn: Nominal resistance Revision: 23-pr-14 4 ocument Number: 53057
Legal isclaimer Notice Vishay isclaimer LL PROUT, PROUT SPIITIONS N T R SUJT TO HNG WITHOUT NOTI TO IMPROV RLIILITY, UNTION OR SIGN OR OTHRWIS. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. xcept as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. ustomers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material ategory Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-ompliant fulfill the definitions and restrictions defined under irective 11/65/U of The uropean Parliament and of the ouncil of June 8, 11 on the restriction of the use of certain hazardous substances in electrical and electronic equipment () - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS irective 02/95/. We confirm that all the products identified as being compliant to irective 02/95/ conform to irective 11/65/U. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-ree follow Halogen-ree requirements as per J JS709 standards. Please note that some Vishay documentation may still make reference to the I 61249-2-21 definition. We confirm that all the products identified as being compliant to I 61249-2-21 conform to J JS709 standards. Revision: 02-Oct-12 1 ocument Number: 91000