STYRENATED ACRYLIC EMULSION DATA SHEET Description EPS 2510 is a styrenated acrylic emulsion offering excellent early water and humidity resistance, as well as corrosion resistance. In addition, EPS 2510 can be formulated with a wide variety of co-solvents, and with its excellent shear stability can be used in the grind phase of the formula. Due to these properties, as well as excellent adhesion to a variety of ferrous and non-ferrous substrates (including various plastics), EPS 2510 is an excellent choice for both DTM primers and topcoats. Excellent block, mar, and print resistance High gloss, and good corrosion resistance Compatible with water reducible alkyds and epoxy esters Based on the early hydrophobic properties of EPS 2510, it is also an excellent choice for high performance waterproofing paints on cementitious substrates and can be used as the binder in tile mastics. Excellent early water and humidity resistance Excellent adhesion to concrete and masonry substrates Passes ASTM D 7088-04: Resistance to hydrostatic pressure for coatings used in below grade applications applied to masonry No APEO containing raw materials Specifications Suggested Coalescing Solvent(s) (% Solvent on Binder Solids Pass 40 F LTC Test) Weight Solids: 45.0 ± 0.7% Texanol and / or EPS 9147 20% Weight/Gallon: 8.70 ± 0.10 Typical Properties ph: 7.0-8.0 Suggested Formulations EPS 2510 WHT1 - White Masonry Waterproofing EPS 2510 WHT ST1 - White High Gloss Enamel Volume Solids: 42.5 ± 0.7% EPS 2510 BLK SG1 - Black Semi Gloss Dip MFFT: 44 C EPS 2510 ROX SP1 - Red Oxide Spray Primer EPS 2510 WHT ST2 - High Gloss White blend w/ WR Alkyd EPS 2510 TM-P Premium Tile Mastic 111014
FORMULA: EPS 2510 WHT1 (7/08) WHITE MASONRY WATERPROOFING 100.8 12.10 Water Add under agitation and high 15.0 1.70 Tamol 2001 Dow Speed disperse to 5 to 6 Hegman. 2.0 0.28 Surfynol 104A Air Products 3.0 0.35 BYK 024 BYK 4.0 0.51 AMP 95 Dow 150.0 4.38 R 902 Du Pont 250.0 11.50 Minex 7 Unimin. 15.0 0.32 Zoco 103 Zochem 522.0 60.00 EPS 2510 EPS Add to grind paste under agitation. 3.0 0.33 Nuosept 498 Ashland 13.0 1.64 Texanol Eastman 10.0 1.20 Sodium Nitrite 4% 5.0 0.55 Fungitrol 920 Ashland 34.0 3.89 EPS 9147 EPS 1.0 0.12 Optiflo H600 BYK Use to adjust viscosity. 10.0 1.15 Optiflo L100 BYK 1137.8 100.00 Totals Typical Properties Weight Solids 61.31 % Viscosity, (Stormer) 110-120 KU Volume Solids 46.97 % ph 8.0 9.0 Pigment Weight 36.50 % Color White Pigment Volume Conc. 38.86 % Pigment/Binder 1.77 VOC 45 g/l Weight/Gallon 11.38 lb/gal Brush & Roll rev. 02-17-2011
FORMULA: EPS 2510 WHT ST1 (04-03-07) WHITE HIGH GLOSS SPRAY ENAMEL 100.0 11.49 EPS 2510 EPS Add in order with good 40.0 4.80 Water agitation. 9.0 1.03 Disperse-Ayd W-33 Elementis 4.0 0.55 Surfynol 104A Air Products 3.0 0.36 S-675 defoamer Hi-Mar Specialties 1.0 0.13 AMP 95 Dow 200.0 5.86 TiPure R-706 Du Pont Add with agitation; grind 7+ Hegman. 480.0 55.17 EPS 2510 EPS Letdown in order with 50.0 6.00 Water good agitation. 4.0 0.54 Ammonium Hydroxide Add grind at this point. 47.5 5.70 Water Premix and add with 10.0 1.20 4% Sodium Nitrite solution agitation. 3.0 0.34 Rheolate 1 Elementis 52.2 6.82 DPnB Lyondell 1003.7 99.99 Totals Weight Solids 46.90 % (at 1.0-1.2 mils DFT on CRS) Volume Solids 35.31 % Viscosity (Stormer) 70-80 KU Weight / Gallon 10.04 lb/gal ph 8.0-9.0 Pigment Volume Conc. 17.00 % 60 Gloss (measured @ 1.15 mils) 86 Pigment / Binder 0.76 VOC 156 g/l 1.30 lb/gal Spray (Conventional, Airless, or Air-Assist) rev 06-06-2011
FORMULA: EPS 2510 BLK SG1 (04-03-07) SEMI GLOSS BLACK DIP 500.0 57.47 EPS 2510 EPS Add in order with good 40.0 3.94 Novocolor IP 8593 Black CCA agitation. 230.0 27.61 Water Add separately with 10.0 1.20 4% Sodium Nitrite solution good agitation. 56.3 7.50 Butyl Cellosolve (EB) Eastman 3.0 0.40 Ammonium Hydroxide 4.0 0.48 BYK 346 BYK 3.0 0.39 Drewplus L-475 Ashland 4.0 0.45 Rheolate 1 Elementis 10.0 0.56 Fuji Sylysia 350 Fuji Silysia Add with agitation. 860.3 100.00 Totals (.6-.8 mils DFT on CRS) Weight Solids 30.28 % Viscosity (#3 Zahn Cup) 18-22 sec Volume Solids 27.15 % ph 8.0-9.0 Weight / Gallon 8.60 lb/gal 60 Gloss (measured @ 0.7 mil) 27 Pigment Volume Conc. 6.14 % Pigment / Binder: 0.11 VOC 200 g/l 1.67 lb/gal Dip, Spray rev 06-06-2011
FORMULA: EPS 2510 ROX SP1 (04-03-07) RED OXIDE SPRAY PRIMER 90.0 10.80 Water Add in order with good 16.0 1.82 Disperbyk 190 BYK agitation. 4.0 0.45 Triton CF-10 Dow 2.0 0.23 BYK 024 BYK 1.0 0.13 AMP 95 Dow 65.0 1.75 Kroma Red Iron Oxide RO-8097 Elementis Add with agitation 150.0 6.65 Atomite Imerys 50.0 1.99 SZP-391 Halox Grind to 6+ Hegman. 500.0 57.47 EPS 2510 EPS Letdown in order. 3.5 0.39 Nuosept 495 Ashland Add grind at this point. 81.8 9.82 Water Mix well before adding 10.0 1.20 4% Sodium Nitrite solution with good agitation. 2.0 0.22 Rheolate1 Elementis 45.0 5.88 DPnB Lyondell 6.8 0.73 Santicizer 160 Ferro 1.0 0.12 Water Premix and use to 1.0 0.11 Acrysol RM-825 Dow adjust viscosity. 1031.1 100.00 Totals (1.0-1.2 mils DFT on CRS) Weight Solids 49.68 % Viscosity (Stormer) 70-80 KU Volume Solids 37.19 % ph 8.0-9.0 Weight / Gallon 10.31 lb/gal Pigment Volume Conc. 29.85 % Pigment / Binder 1.18 VOC 130 g/l 1.08 lb/gal Spray, Brush, Roll rev 06-06-2011
EPS 6264 FORMULA: EPS 6264/2510 WHT ST2 (04-03-07) ALKYD / ACRYLIC HIGH GLOSS WHITE 110.0 12.50 EPS 6264 EPS Add in order with good 5.0 0.57 Disperbyk 190 BYK agitation. 4.0 0.52 Drewplus L-475 Ashland 4.0 0.48 BYK 346 BYK 1.0 0.13 AMP 95 Dow 20.0 2.66 EB Eastman 175.0 5.12 Ti-Pure R-706 Du Pont Add and grind to 7+H. 24.0 3.20 EB Eastman Add after grind is achieved. 400.0 45.98 EPS 2510 EPS Letdown in order with 220.0 26.41 Tap water good agitation. 5.0 0.67 Ammonium Hydroxide 10.0 1.20 4% Sodium Nitrite 2.0 0.22 Nuosept 485 Ashland Add grind at this point. 3.0 0.34 Rheolate 1 Elementis Add with agitation. 983.0 100.00 Totals (at 1.0-1.2 mils DFT on CRS) Weight Solids 45.01 % Volume Solids 33.97 % Viscosity (Stormer) 60-70 KU Weight / Gallon 9.83 lb/gal ph 8.0-8.5 Pigment Volume Conc. 15.63 % 60 Gloss (measured @ 1.05 mils) 91 Pigment / Binder 0.68 VOC 216 g/l 1.80 lb/gal Spray, Dip Acrylic/Alkyd Ratio (70/30) rev.06-06-2011
FORMULA: EPS 2510 TM-P (10/13) PREMIUM TILE MASTIC 273.56 31.44 EPS 2510 EPS Add in order with good agitation 8.86 1.06 Water 12.74 1.40 Triton X-405 Dow 0.22 0.03 BYK 024 BYK 649.00 28.76 Duramite Imerys 22.15 1.12 Attagel 50 BASF Add and mix until smooth 190.49 21.90 EPS 2510 EPS Let down in order with good agitation 63.13 7.58 Water 0.00 0.00 Ammonium Hydroxide Adjust to ph 8.5 1.27 0.15 Nuosept 498 Ashland 18.83 2.90 Odorless Mineral Spirits 16.61 1.78 Ethylene Glycol 16.61 1.89 ASE-60 Dow Use to adjust viscosity 1273.48 100.00 Totals Typical Properties Weight Solids 70.19 % Viscosity 4 MM cp Volume Solids 53.97 % ph 7.8-8.2 Pigment/Binder 3.2:1 Color Off-white VOC 0.60 lb/gal 72 g/l Weight/Gallon 12.73 lb/gal rev.10-17-2013