Retail Store Packaging Requirements

Retail Store Packaging Requirements This document details the packaging requirements vendors need to follow when shipping to the Kohl s Retail Distribution Centers. 1 Kohl s Department Stores-08/10/15

Table of Contents Section Carton Requirements 2 Page Number Weights/Dimensions/Strength...3 General Carton Requirements...4 Pack Type Definitions..5 Hardline Drop Test Requirements. 6 Hanger Outline Uses/Sets...7 Carton Packing/Bridge...8 Diagrams..9 Polybags Requirements Definition/Material/Use..10 Exceptions...11 Carton Liner Requirements Definition/Material/Use..12 Illustrations..13 Protective Packaging Guidelines..14 Specialty Packaging Guidelines...15 GS1-128 Label Requirements Definition/Barcode Testing... 16 Quality.....17 Segment Breakdown....17 Segment Information....18-20 Label Examples.21 Label Placement...22-26 Carton Labeling Inner/Outer.27 Stenciling 28-29 DC Order Consolidation/Master Packing Definition.30 Pack by Store.31 Bulk..32 Diagrams.33 Palletization (Live Unloads or if Pre Approved). 34-35

Carton Requirements Weight and Dimensions: With the exception of single selling units that exceed these measurements, all cartons are required to be within these parameters: Carton Weight: Maximum of 50 lbs (equal to 22.7 kilograms) Minimum of 3lbs Any cartons greater than 50lbs must adhere to the following additional packaging requirements. Cartons must have a yellow TEAM LIFT 4 x 6 label The team lift label should be placed on the four largest sides of the carton including to the left of the GS1-128 label Carton Dimensions: Maximum: 36 Long x 26 Wide x 26 High 92 cm Long x 66 cm Wide x 66 cm High Minimum: 12 Long x 9 Wide x 3 High 30 cm Long x 23 cm Wide x 8 cm High Strength Requirements: Vendors are responsible for utilizing cartons strong enough to withstand the rigors of transportation and supply chain processing. Cartons can be stronger than what is required. It is recommended, but not required, that cartons be labeled with their ECT and/or Bursting Strength certification. Furniture Strength Requirements: Vendors should work with Kohl s Furniture Product Development team to ensure packaging meets current standards. UPS. (2012). Package with Care A Guide to Packing Your Shipments.[Brochure]. UPS. 3

General Carton Requirements: Pack shipments to the same level of detail as the purchase order is written. If Vendors have a packaging alternative to corrugate, contact floorready@kohls.com for approval. Cartons can be new or repurposed. Any additional bar codes or print on repurposed cartons must be covered or disabled so they do not interfere with the scanning of the GS1-128 label or other DC processing activities. All cartons must adequately protect product during transit and DC processing Seal cartons with reinforced security tape that is moisture and temperature resistant Do not seal cartons with bands, straps, staples, twine, glue or any closure material other than tape. However, it is approved to use plastic strapping to seal gaylords and CDUs. Use the correct size carton for the merchandise; do not over- or under-pack cartons Cartons must be wide enough to allow items to fit squarely in the carton If packing small items, consider master packing in order to use larger cartons (Page 13-14) When applicable, cartons should be marked in BOLD lettering, Fragile, Do Not Freeze, Melt Risk, etc. (i.e. glassware, cosmetics, candles) 4

Pack Type Definitions Bulk (B) Pack Type: Pack one UPC/SKU (one style, color, size combination) per carton Mixed SKU cartons are prohibited on bulk shipments Direct import orders must follow inner pack/outer pack instructions transmitted on the PO EDI Prepack (M) Pack Type: Prepack definition = pre-determined ratio of multiple UPCs/SKUs set by the buyer and transmitted on the EDI purchase order The EDI purchase order directs the number of prepacks to pack in each carton The EDI purchase order carries prepack level data and line item data Packing information for private brands via Li & Fung is on the objective sheet or PLX information Pack-by-Store ( PBS ) Pack Type: Units are assigned to a particular store Multiple UPCs/SKUs may be packed in the same carton Total units per carton may vary per store needs PBS does not apply to Kohl s Direct Imports/Private Brands 5

Hardline Drop Test Requirements Kohl s expects vendors of breakable/hardline product to perform drop testing using the following guideline as a minimum standard. Test results should be kept on file by the vendor and Kohl s reserves the right to request the documentation in the event a quality issue is detected. Selection of shipping cartons for drop test: Shipping cartons are randomly selected from bulk production for drop test. Total shipping cartons Shipping cartons for drop test 1-7 Not required 8-26 1 27-63 2 64-124 3 125 + 3 For All Hardline Items (except glassware, ceramicware): Shipping carton drop height is determined according to shipping carton weight: Carton weight Drop height 0 < 21 lbs 30" (76 cm) 21 < 41 lbs 24" (60 cm) 41 < 61 lbs 18" (45 cm) 61 < 100 lbs 12" (30 cm) For Ceramicware: Carton weight Drop height - 18" (45 cm) For glassware: Carton weight Drop height - 12" (30 cm) Evaluation: Dropped cartons must be opened for inspection, to identify damaged or defective product related to the drop test. Defect Classification List are located on www.connection.kohls.com Private brands > Quality Assurance > Defect Classification Lists The percentage of defective units cannot exceed 2.5%, based upon Kohl's OQL (outgoing quality level). If it does exceed, the drop test failed and must be reviewed & corrected prior to shipping. 6

Hangers Use: Use 584 sweater hangers in place of 484 top hangers when needed to prevent hanger marks or garment shoulder slippage Only Kohls approved paper loops are an acceptable means to bind / secure hangers together where necessary some examples of unacceptable means to bind / secure hangers together are rubber bands, tape and plastic twist ties, or any means that ties the hangers together please contact vendor.services@kohls.com Apply Kohl s designated program hangers Hangers may be anchored to the internal sides of the carton when needed to prevent garments from shifting in transit When using carton liners, hanger hooks do not need to be exposed When using poly bags, hanger hooks need to be exposed Sets: Two-Piece Sets: Insert bottoms hanger through the off-set loop on the tops hanger Apply crown sizer to the top hanger only Three-Piece Sets: Follow the above two-piece directive Attach third garment hanger to the two-piece set using connector 9916N Apply crown sizer to the top hanger only 7

Hanger Carton Packing: Lay garments head to toe in the carton, alternating the direction of the garments as needed There should be no more than one horizontal fold per garment when packed Fold as close to the bottom of the garment as possible Vertical folding is acceptable if necessary to accommodate the garment width Fold as close to side seams as possible Do not place garment into the carton in a wrinkled manner, as the wrinkles will become permanent in transit Follow Kohl s carton dimensions guidelines as stated on p. 2 of this section The carton should be only 1 to 1 ½ wider than the size of the hanger Hangers must fit squarely in the cartons (not at an angle) Adjust your carton length and height according to the size of the pack Cardboard Bridge: A cardboard bridge may be used in the carton to remove some of the pressure on garments in the bottom half of the carton. Use a bridge in carton packing for special fabrications that may become very wrinkled or crushed from the excess weight and pressure of other garments Recommended for cartons with 12 or more pieces of special fabrications. (silks, moleskin, velvets, etc) The cardboard used can be of a single corrugated quality. Ends of the bridge are left open so there should be no need for a larger length in the outer carton, and no more than ¼ to ½ inch wider in width. Please note that hangers should still be put in the garments. 8

Diagrams: Perforations must follow these examples Figure 1: Garment Bag for Bottoms Figure 2: Garment Bag for Tops, Coats or Dresses 9

Polybag Requirements Definition: A poly bag is a poly material that is used as a bag to protect individual hanging and folded garments. The use of poly bags is not required; they should only be used if needed to ensure product arrives to Kohl s in saleable condition. A child safety warning is required on all poly bags 9 x 12 or larger o Recommended Verbiage: "Warning: To avoid danger of suffocation, keep this plastic bag away from babies and children. Do not use this bag in cribs, beds, carriages or playpens. The plastic bag could block nose and mouth and prevent breathing. This bag is not a toy." Material: Clear polyethylene material (PE) with no BHT Thickness: 0.00075 to.00125 inches or 0.019mm to 0.032mm Recyclable material All poly bags must be perforated for ease of removal Vendors may use poly bag supplier of their choice Use: Individual poly bagging must be approved by FloorReady@kohls.com One large poly bag may be used to protect all hanging and folded garments packed within one carton A poly bag is the preferred method for packing inner pack quantities transmitted on Import Bulk orders and Inner Prepack orders Poly bags must be 6 to 12 inches longer than the garment(s) The large poly bag may be used in place of a carton liner A single piece of tape or heat seal may be used; however, sealing is not required 10

Polybag Exceptions Sweaters: may use single poly bag for heavily embellished, high loft chenille or cashmere sweaters Embellished Knit Tops: may use single poly bag and tissue Delicate Fabrics: may use single poly bag, tissue and cardboard bridge to minimize wrinkles in sateen, micro fiber, chenille, velvet, leather or suede garments 11

Carton Liner Requirements The following requirements must be followed when preparing shipments to Kohl s that are standard Bulk purchase orders with inner quantities of one (1) These requirements are to be followed when the vendor is given a standard Import, Landed, or Domestic Bulk purchase order Definition A carton liner is a poly material that lines the entire inside of the carton before garments are packed inside. Carton liners are used to provide additional protection for the garments while eliminating the need for individual poly bags Material: Clear polyethylene material (PE) with no BHT Thickness: 0.00075 to.00125 inches or 0.019mm to 0.032mm Recyclable material Vendors may use carton liner supplier of their choice A child safety warning is required on all poly bags 9 x 12 or larger o Recommended Verbiage: "Warning: To avoid danger of suffocation, keep this plastic bag away from babies and children. Do not use this bag in cribs, beds, carriages or playpens. The plastic bag could block nose and mouth and prevent breathing. This bag is not a toy." Use Use one (1) carton liner for the entire quantity of each carton Pack hanging garments head to toe in flat carton 12

Carton Liner Illustrations: Carton liner inside carton prior to packing order Carton liner with garment inside with hanger on the left side Carton liner with garment inside with hanger on right side Carton liner sealed after packing garments prior to closing carton 13

Protective Packaging Guidelines Acceptable: Paper loops to secure hangers Bubble wrap Corrugated cardboard wrap Cardboard dividers Dunnage or paper stuffing for books Plastic strapping on gaylords and CDU s Unacceptable: Using tape or rubber bands on hangers Tying hangers together Tissue (unless directed by buyer or product manager) Pins, plastic clips, or tie backs (unless directed by buyer or product manager Packing peanuts Shredded paper Strapping an outer cartons Inserting anything between a garment and a pinch clip hanger (i.e. cardboard, fabric, etc) 14

Specialty Packaging Guidelines Shoe Packing: Pack shoes with the label end facing the top of the carton All boxes must face the same direction If packing an empty shoebox to fill space, write EMPTY on the shoebox in large print Apply suppressed retail price tickets to the same end of the shoebox as the preprinted barcode 15

GS1-128 Carton Labeling 16 All cartons being shipped to Kohl s stores or distribution centers must have compliant Kohl s GS1-128 carton labels For import orders, please refer to Appendix SP-11 for Private Brand and Direct Import GS1-128 Requirements located on www.connection.kohls.com Logistics & Routing > Appendices > Shipment Packing GS1 US Definition (Formerly the Uniform Code Council) GS1 is the global standards authority for item (UPC and EAN) and logistical numbering. In addition to managing the numbering assignments, GS1 provides the retail industry guidelines for supply chain identification. Every country has a regional organization and GS1 US is the non-profit organization in the United States. Kohl s requires that all vendors review and follow carton label formats and barcode data requirements in accordance with the guidelines posted on the GS1 US website (listed below). Kohl s does not receive at Master Carton level or Pallet level. GS1-128 barcode must be at the individual carton level. Only apply one GS1-128 label per carton. Only one SSCC- 18 barcode is allowed per carton. For detailed information regarding GS1 identification, please contact use the following contact: GS1 US Tel: 937-435-3870 Fax: 937-435-7317 www.gs1us.org GS1-128 Barcode Testing Bar Code Graphics, Inc. is the Kohl s barcode testing center for GS1-128 labels All domestic ship points must be tested for each Kohl s pack type format, including vendors already shipping to Kohl s Labels for each pack type (Bulk, Prepack, Pack by Store) that the vendor currently ships to Kohl s must be tested New Kohl s vendors must have GS1-128 labels for each ship point tested and certified within 90 days of receiving their first Kohl s PO Contact Bar Code Graphics, Inc. at test@barcode-us.com or (800) 662-0701 ext. 511 for label testing information Contact Bar Code Graphics, Inc. at http://kohls.symboltest.com for registering, testing and certification

GS1-128 Barcode Quality The industry standard for acceptable quality is an ANSI Grade of C ANSI was established in 1990 and is made up of 9 parameters that grade the print quality of bar codes Printed bar codes should be verified in order to guarantee scannability Kohl s GS1-128 Label Format: Segment Breakdown Use a 4 x 6 Standard Size Zone A Zone B From: To: Vendor s Shipping Address Kohl s Receiving Location, Facility Number and Address Zone C Zone D Ship to Postal Zip Code Carrier Name (if available) (GS1-128 barcode) Pro # (if available) Bill of Lading Number (if available) Zone E Kohl s PO Number Style Number color size total units (if Prepack, total units by size and color) Zone G Kohl s Store Number or Distribution Center Number (GS1-128 barcode) Zone H If Pack by Store PO type, list store number. If Bulk or Prepack PO type, list DC number. Zone I SSCC-18 (GS1-128 barcode) 17

Segment Information: ZONE A Title Height Width Characteristic Data Content FROM 1.0 inch [25.4 mm] 1.25 inch [31.75 mm] Mandatory. Vendor s Shipping Address ZONE B Title Height Width Characteristic Data Content TO 1.0 inch [25.4 mm] 2.75 inch [69.85 mm] Mandatory. Kohl s Receiving Location, Facility Number and Address ZONE C Title Height Width Characteristic Data Content SHIP TO POSTAL CODE 1.0 inch [25.4 mm] 2.5 inch [63.5 mm] Mandatory. Ship To Postal Code. Bar Code Specifications: Bar Code Symbology GS1-128 Application Identifier 420 Bar Code Data Height X-Dimension Quiet Zone 5-digit Ship To Postal Code 0.5 inch [12.7 mm] minimum 0.010 inch [.254 mm] minimum 0.25 inch [6.35 mm] minimum. Each Quiet Zone preceding and following the bar code. ZONE E 18

Height Width Characteristic 1.5 inch [38.1 mm] 4.0 inch [101.6 mm] Mandatory Bulk & Prepack Kohl s PO Number Dept Number Style Number Units per color and size Data Content (Vendor may incorporate the Human Readable carton content information to eliminate separate content labels on the cartons.) Pack by Store Kohl s PO Number Dept Number Total Units per Carton ZONE G Title Height: Width Characteristic Data Content FOR [mark for number] 1.0 inch [25.4 mm] 2.5 inch [63.5 mm] Mandatory. The 5-digit final destination number plus a leading zero (to allow use of GS1-128 Subset C for efficiency). Example: Store Number 00246 would be encoded as "000246". Bar Code Specifications: Bar Code Symbology GS1-128 Application Identifier 91 Bar Code Data Height Bulk & Prepack 5-digit Distribution Center Number with leading padded 0 (6 digits total) Pack By Store 5-digit Store Number with leading padded 0 (6 digits total) 0.5 inch [12.7 mm] minimum 19

X-Dimension Quiet Zone 0.020 inch [.508 mm] minimum for automated sortation. 0.25 inch [6.35 mm] minimum. (Left & Right Quiet Zone) ZONE H Height Width Characteristic Data Content Text Size 1.0 inch [25.4 mm] minimum. 1.5 inch [38.1 mm] Mandatory. Bulk & Prepack 5-digit Distribution Center Number Pack By Store 5-digit Store Number 26 pt. Bold font or larger ZONE I Title Height Width Characteristic Data Content SSCC-18 1.5 inch [38.1 mm] 4.0 inch [101.6 mm] Mandatory Serial Shipping Container Code. SSCC-18 Bar Code Specifications: Bar Code Symbology GS1-128 Application Identifier 00 ZONE I (continued) Bar Code Data Height X-Dimension Quiet Zone Bar Code Text 18-digit SSCC-18 number. A prerequisite for proper carton labeling is that Vendors must be EDI/ASN active. 1.25 inch [31.75 mm] minimum 0.020 inch [.508 mm] minimum 0.25 inch [6.35 mm] minimum. (Left & Right Quiet Zone) The human readable SSCC-18 number that is printed above the bar code must be printed in a bold font, no smaller than 12 pt. 20

Kohl s GS1-128 Label Examples - (Not to scale) Bulk Landed Label Format Prepack Landed Label Format Zone A Zone B Zone A Zone B FROM: Vendor s Shipping TO: Kohl s Department FROM: Vendor s Shipping TO: Kohl s Department Zone C Kohl s PO Number 21

Label Placement General Guidelines: Each carton is required to have one GS1-128 label Place only one GS1-128 label on a carton 22 Kohl s Department Stores 08/10/2015 If carton contents and address are included as part of the GS1-128 label in a human readable format, an additional label for this purpose is not required GS1-128 Labels must be placed: On the second largest side. The largest side will be facing down on our conveyors. Therefore, labels must be placed on the second largest side. In the lower right quadrant These placement guidelines are required even if the second largest side of the carton has the box seam as long as the GS1-128 barcode does not cross the seam of the box (see examples below). If there is stenciling on the cartons, leave the lower right hand quadrant of the second largest side of the carton vacant for the GS1-128 label GS1-128 Labels must be Placed in an upright position Barcode must be read vertically Do not place sideways or diagonally The SSCC-18 bar code on the carton label must be 3.0 inches from either vertical edge of the carton no less than 1.25 inches up from the bottom horizontal edge Do not place SSCC-18 bar code over a flap seam or around the corners of a carton The human readable SSCC number that is printed above the bar code must be printed in a bold font, no smaller than 12 pt Do not place tape over any bar code For merchandise selling in the same carton as shipping Do not place labels over product ID Numbers UPC Bar Codes & retail price other consumer information on merchandise

Vendors are responsible for GS1-128 labels being intact upon shipment arrival in scannable condition upon shipment arrival Be sure to use the correct combination of paper, ink and adhesive Cartons containing liquid product: Cartons containing liquids must be oriented with the container opening(s) facing up to prevent spilling. Then, GS1-128 label should be placed in the lower right corner of the longest side of the carton based on this orientation. Cartons should also be stenciled with This side up arrows. For questions regarding label placement for cartons that do not meet Kohl s dimension requirements or for sensitive or fragile product that requires specific carton positioning, please contact FloorReady@kohls.com VICS standard placement on cartons 7.5 inches in height and above: Side with largest surface area (LxWxH) Side with second largest surface area (LxWxH) Side with smallest surface area (LxWxH) SSCC-18 Bar Code must cover this band and label must always be in bottom right. 23 Kohl s Department Stores 08/10/2015

Label Placement: Cartons 7.5 or 19cm in Height or Less Placement of label folded over from the side to the top of the carton One GS1-128 label per carton 3 inches from Vertical edge No less than 1.25 inches from the bottom edge of carton The SSCC-18 barcode on a carton label must not be: folded around the edges or corners of the carton wrinkled wrapped around the edges or corners of the carton The part of the label that contains the SSCC-18 bar code must be visible on the side of the carton as pictured below. The remainder of the label is applied to the top of the carton. Note: The label can be applied over stencil marks if needed. Largest side Second largest side Smallest side 2.5 Inches 1.25 Inches 3 Inches 24 Kohl s Department Stores 08/10/2015

Label Placement: Cartons in which height is greater than width or length Carton should be orientated with the largest surface being placed down resulting in the height becoming the width or length (examples below) Base label placement on this orientation regardless of which side has the seam Note: if the seam is on the second largest side, wrap the label over the top and side with the barcode visible to avoid covering the seam Placement example when there is enough space to apply the label below the seam without having to cover the seam: Largest side Second largest side Smallest side Placement example when there is enough space to apply the label below the seam without having the SSCC-18 barcode cover the seam: **** NOTE GS1-128 Placement for Ecommerce is different! **** Please review Ecommerce Packaging Guidelines 25 Kohl s Department Stores 08/10/2015

Largest side Smallest side Second largest side 2.5 Inches 1.25 Inches 3 Inches Placement example when there is NOT enough space to apply the label below the seam without having to cover the seam with the label: Largest side Smallest side Second largest side 3 Inches 1.25 Inches Top Placement Vendors who are authorized to ship in cartons that are less then 3 in height may place the GS1-128 label on the top of the carton. The label must be placed consistently in one corner on the top of the carton. The SSCC-18 barcode should be positioned so that it is not across a seam or around any corner or edge of the carton. 26 Kohl s Department Stores 08/10/2015

Carton Markings Inner Carton (Required for Inner Pre Pack Cartons) Inner carton marking must: Be PO specific List the style number, color and size (if applicable) Include the total number of units contained within the inner carton Outer Carton Outer carton markings are required for all Import and Landed orders but NOT required for Domestic orders. Landed/POE Shipments: Vendor is the Importer of Record Direct Import Shipments: Kohl s is the Importer of Record 27 Kohl s Department Stores 08/10/2015

Stenciling for Landed & Direct Import Shipments Vendor Side Mark: Destination Kohl s Department Stores May also be printed as Kohl s Department Stores, Inc. Do not include a street address Do not use a Distribution Center address Buying Agent for direct import shipments if applicable Vendor Name Country of Origin Product Side Mark: Kohl s Purchase Order Number Style Number UPC Number Pack UPC for Prepack Shipments Item UPC for Bulk Shipments Color Example of Shoe Prepack Stenciling: SIZE 6 ½ 7 7 ½ 8 8 ½ QTY 2 2 2 3 3 SIZE 9 9 ½ 10 10 1/2 11 QTY 3 3 2 2 2 TOTAL UNIT 24 TOTA PACK 1 S: L S: 28 Kohl s Department Stores 08/10/2015

Stenciling Side Mark Placement: When stenciling cartons, leave the lower right hand quadrant of the longest side of the carton vacant for the GS1-128(SSCC-18) label Side marks may be stenciled on one side or on multiple sides of the carton at vendor s discretion Vendor side mark may be stenciled on same side as product side mark or on opposite sides at vendor s discretion 29 Kohl s Department Stores 08/10/2015

DC Order Consolidation/Master Packing Bulk and/or Pack by Store (PBS) orders that are too small to meet the minimum size and weight carton requirements may be consolidated into a larger carton at the PO/DC level DC order consolidation may be used in combination with cartons that meet Kohl s minimum carton requirements Master cartons should be labeled with a GS1-128 carton label with the phrase MASTER PACK in place of the SSCC-18 barcode Each inner pack within the master carton must be individually GS1-128 labeled Store number must be on the GS1-128 label for Pack-by-Store shipments Master pack cartons must not exceed Kohl s maximum carton dimension and weight requirements Master packing does not apply to Kohl s Direct Imports/Private Brands Definition: Pack by Store (PBS) and/or Bulk and/or orders that are too small to meet the minimum size and weight carton requirements may be consolidated into a larger carton at the PO/DC level Order Consolidation may be used in combination with cartons that meet Kohl s minimum carton requirements Benefits of Consolidation DC Orders to Kohl s Reduces excess corrugated cardboard in the supply chain Decreases transportation cost though improved cube utilization Program Definitions Master Carton The master carton used to consolidate orders at the DC level Follows Outer carton weight and dimension maximums and minimums The carton count on the Bill of Lading should be equal to the total number of master/outer cartons The ASN should reflect the carton data based on the GS1-128 labels 30 Kohl s Department Stores 08/10/2015

Pack by Store PO - DC Order Consolidation Guidelines Master Carton Master cartons should be labeled with a GS1-128 carton label with the phrase MASTER PACK in place of the SSCC-18 barcode. See Diagram 1. Master cartons containing Pack by Store orders must be labeled with content label(s) that list the store orders in sequential order. See Diagram 2. Store Orders (Inner Packs) Each inner store pack within the master carton must be individually GS1-128 labeled The SSCC-18 barcode on the GS1-128 label must not be folded around the edges of the inner pack Master Carton Packing Orders that include quantities sufficient enough to meet both the minimum carton weight and dimension requirements should be packed separately in their own conveyable corrugate (cardboard) cartons and labeled with GS1-128 carton labels All units for a store must be packed within the same master carton, preferably within the same inner pack Inner store orders should be packed in sequential order, top to bottom or front to back, both within each master carton and across all master packed cartons For order consolidation that exceeds one master carton, each master carton must be labeled carton number of total number of master packed cartons at the PO level Example: PO 1234567: carton 1 of 10, carton 2 of 10 Kohl s Store to DC Association should be used These are located on www.connection.kohls.com Logistics & Routing > Store to DC Associations Acceptable packaging material for inner store orders: Polybags are preferred (polybags may be zip top, heat sealed or taped) Do NOT use the GS1-128 label to seal the polybag Polybags must meet Kohl s polybag guidelines Corrugate cartons Inner packs should be the smallest size possible to fit the product 31 Kohl s Department Stores 08/10/2015

Bulk PO DC Order Consolidation Guidelines Carton Marking & Labeling Master Carton Master cartons should be labeled with a GS1-128 carton label with the phrase MASTER PACK in place of the SSCC-18 barcode. See diagram 1 Carton contents label is not required on the master carton for bulk order consolidation Bulk Orders Each inner bulk pack within the master carton must be individually GS1-128 labeled The SSCC-18 barcode on the GS1-128 label must not be folded around the edges of the inner pack Carton Packing Orders that include quantities sufficient enough to meet both the minimum carton weight and dimension requirements should be packed separately in their own conveyable corrugate (cardboard) cartons and labeled with GS1-128 carton labels Each inner pack should be single-sku meaning that all quantities for an individual SKU inside the master carton must be inner packed together All units for an individual SKU must be packed within the same master carton, preferably within the same inner pack Acceptable packaging material for inner orders: Polybags are preferred (polybags may be zip top, heat sealed or taped) Do NOT use the GS1-128 label to seal the polybag Corrugate cartons Inner packs should be the smallest size possible to fit the product 32 Kohl s Department Stores 08/10/2015

Diagram 2: Carton Content Label Store Listing 0039 0041 0043 0044 0045 0049 33 Kohl s Department Stores 08/10/2015

Palletization (Live Unloads or if Pre-Approved) Guidelines: Live unload shipments must be palletized and less than 10 pallets Drop shipments must be floor-loaded Any shipment tendered to a carrier on pallets must be labeled at the carton level and must also follow the unitization and pallet marking guidelines listed below Each pallet should contain only one purchase order If the PO quantity is small, additional POs may be placed on the same pallet Guidelines for shipping multiple POs on a pallet: Use a cardboard divider between layers to separate the POs Note that there are multiple POs on the pallet label List the PO numbers on the pallet label Do not stack the combination of pallets and freight higher than the trailer door Use standard 48 x 40 x 4 pallets, with no loose or broken boards Pallet Markings Place a label on all four sides of the pallet on the outside of the shrink wrap Do not use a GS1-128/SSCC-18 label to label the pallet In bold legible print, list the following information on the label: Kohl s DC number and address Kohl s purchase order number(s) Number of cartons on the pallet per purchase order Pallet sequence number Live Unload Shipment Pallet Label Used to identify multiple PO s packed to one pallet DO NOT use a GS1-128/SSCC-18 label at pallet level Each carton on the pallet must be individually GS1-128 labeled Kohl s DC # 810 7855 County Rd 140 Findlay, OH 45840 34 Kohl s Department Stores 08/10/2015 Pallet Label Sample Actual Size is 8½ x 11

Wood Packaging Markings for Import Vendors International Standards for Phytosanitary Measures. Regulation of Wood Packaging Material in International Trade. ISPM No. 15. 2009. 35 Kohl s Department Stores 08/10/2015