IIS03_04 RS-3 REVISED NOTE 7 REMOVED STATEMENT IN ASPHALT CONCRETE PAVEMENT THAT IS BEEN IN PLACE MORE THAN ONE YEAR.

PAGE INTERIM STANDARD REVISION 304.02 IIS03_04 RS-3 REVISED NOTE 7 REMOVED STATEMENT IN ASPHALT CONCRETE PAVEMENT THAT IS BEEN IN PLACE MORE THAN ONE YEAR. 304.03 IIS03_05 RS-4 REVISED NOTE 4 REMOVED STATEMENT IN ASPHALT CONCRETE PAVEMENT THAT IS BEEN IN PLACE MORE THAN ONE YEAR. 502.01 IIS05_18 MB-3 REVISED FLARE RATE TABLE TO MATCH THE RDM AND AASHTO 1005.10 1005.10 BCQ-10 UPDATED SHEET TO SHOW WINGWALL DESIGNATIONS 1324.10 IIS13_04 OSS-1 THE ELEVATION DRAWINGS WERE UPDATED INCREASING THE PROJECTION ABOVE GRADE FOR FOUNDATIONS AND NOTE 7 AND 8 WERE ADDED 1324.13 IIS13_41 OSS-1 FOOTING DETAIL UPDATED INCREASING THE PROJECTION ABOVE GRADE FOR FOUNDATIONS If you have any questions or comments regarding this revision, please contact Chuck Patterson P.E., at (804) 786-1805, of the Standards and Special Design Section. Sincerely, Signature on file: July 29, 2013 B. A. Thrasher, P.E. State Location & Design Engineer Page 2 of 2

MC-4 SHOULDER WIDTH LEFT OR RIGHT OF TRAFFIC PAVEMENT ASPHALT MAT L. STANDARD GUARDRAIL, GR-2 OR GR-8 ASPHALT MATERIAL PAVED SHOULDER SEE NOTE 3 SEE NOTE 1 SEE NOTE 2 ASPHALT PAVING UNDER GUARDRAIL (FOR USE WHERE ASPHALT CURB IS NOT REQUIRED) ASPHALT PAVING UNDER G. R. E.P. NOTES: PAVED SHOULDER 5 1. TO BE CONSTRUCTED WITH THE SAME MATERIAL AND TO THE SAME DEPTH AS THE ROADWAY PAVED SHOULDER. DITCH LINE 2. TO BE CONSTRUCTED WITH THE SAME ASPHALT MATERIALS AS THE PAVED SHOULDER TO THE FOLLOWING DEPTHS: ALLOWABLE DEPTHS OF ASPHALT MATERIAL GR-6 SHOULDER LINE IM-19.0A OR IM-19.0D BM-25.0 2" MIN MIN GR-6 TERMINAL 3. DEPTH OF ASPHALT MATERIAL MAY BE EXTENDED AT THE CONTRACTOR S OPTION TO COINCIDE WITH THE BOTTOM OF THE PAVED SHOULDER COURSE AT NO INCREASE IN THE QUANTITY OF ASPHALT MATERIAL COMPUTED USING THE ABOVE SPECIFIED DEPTH. 5 10 : 1 SLOPE OR FLATTER ASPHALT PAVING UNDER G. R. E.P. 4. ADDITIONAL 5 FEET ASPHALT PAVING BEYOND POINT WHERE GUARDRAIL CROSSES SHOULDER LINE. PAVED SHOULDER 5. FOR ADDITIONAL DESIGN AND PLACEMENT INFORMATION SEE SHEET 1 OF 2. SHOULDER LINE GR-7 & GR-9 TERMINALS METHODS FOR BEGINNING & ENDING ASPHALT PAVING UNDER GUARDRAIL AND GUARDRAIL INSTALLATION SITE PREPARATION REQUIREMENTS FOR GR-7 AND GR-9 SEE STANDARD. ASPHALT CURB AND GUTTER SHEET 2 OF 2 REVISION DATE (ASPHALT PAVING UNDER GUARDRAIL) 105 201.08 502

STANDARD TITLE PAGE PR-2 PLAIN AND REINFORCED CONCRETE PAVEMENT SHOWING REINFORCEMENT, LONGITUDINAL AND TRANSVERSE JOINTS 301.01 PLAIN AND REINFORCED CONCRETE PAVEMENT SHOWING REINFORCEMENT, LONGITUDINAL AND TRANSVERSE JOINTS 301.02 PLAIN AND REINFORCED CONCRETE PAVEMENT SHOWING REINFORCEMENT, LONGITUDINAL AND TRANSVERSE JOINTS 301.03 STANDARD LOAD TRANSFER ASSEMBLY CONTRACTION JOINT 301.04 STANDARD LOAD TRANSFER ASSEMBLY EXPANSION JOINT 301.05 PR-3 8" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (WIRE MESH REINFORCEMENT) THIS STANDARD IS VOID 301.06 8" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (STEEL BAR REINFORCEMENT) 301.07 8" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (FOR USE WITH BAR OR WIRE MESH REINFORCEMENT) 301.08 8" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (LEAVE OUT JOINT DETAIL) 301.09 PR-4 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (STEEL BAR REINFORCEMENT) 301.10 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (FOR USE WITH BAR REINFORCEMENT ONLY) 301.11 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT (LEAVE OUT JOINT DETAIL) 301.12 PR-5 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.13 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.14 9" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.15 PR-6 10" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.16 10" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.17 10" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.18 PR-7 11" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.19 11" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.20 11" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.21 PR-8 12" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.22 12" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.23 12" CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.24 PR-9 1 CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.25 1 CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.26 1 CONTINUOUSLY REINFORCED CONCRETE PAVEMENT 14 FOOT TRAVEL LANE 301.27 XJ-1 BRIDGE APPROACH EXPANSION JOINT (FOR WIDENING OR MAINTENANCE OF EXISTING XJ-1 ONLY) 302.01 BRIDGE APPROACH EXPANSION JOINT (INSTALLATION CRITERIA) 302.02 WP-1 METHOD OF WIDENING BRIDGE APPROACH PAVEMENT THIS STANDARD IS VOID 303.01 WP-2 PAVEMENT WIDENING 303.02 RS-1 CONTINUOUS SHOULDER RUMBLE STRIPS 304.01 RS-3 CENTERLINE RUMBLE STRIPS 304.02 RS-4 CONTINUOUS SHOULDER RUMBLE STRIPES 304.03 RS-5 INTERMITTENT SHOULDER RUMBLE STRIPS 304.04 ACOT-1 ASPHALT CONCRETE OVERLAY TRANSITIONS (REPLACES THE STANDARD TPT-1 TRANSVERSE PAVEMENT TIE-IN) 305.01 INDEX OF SHEETS SECTION 300-PAVEMENT ITEMS REVISION DATE SHEET 1 OF 1 300.01

WP-1 5X 2 BRIDGE ABUTMENT APPROACH SLAB 25X 1 BRIDGE ABUTMENT APPROACH SLAB 5X 2 5X 2 METHOD OF WIDENING APPROACHES TO DUAL STRUCTURES (WITHOUT APPROACH SLAB) (WITH APPROACH SLAB) X RUN-ON SIDE BRIDGE APPROACH SLAB (IF USED) CLEAR ROADWAY WIDTH OF BRIDGE C L L C NORMAL PAVEMENT WIDTH RUN-OFF SIDE BRIDGE WHEEL GUARD X 1 2 GUARD WHEEL BRIDGE 25X 1 25X 1 (WITH APPROACH SLAB) (WITHOUT APPROACH SLAB) NOTES: ON FULL SHOULDER WIDTH BRIDGES, NO WIDENING IS TO BE PROVIDED. X AND X = 1 2 AMOUNT OF BRIDGE WIDENING PER SIDE (10 MAXIMUM). NONE VOID IF BRIDGE DRAINAGE APRONS ARE REQUIRED THE PAVEMENT WIDENING IS TO BE APPLIED AT THE END OF THE DRAINAGE APRON FARTHEST FROM THE ABUTMENT BACKWALL. THIS DRAWING WAS VOID WITH THE JULY 2013 R&B STANDARDS REVISION METHOD OF WIDENING BRIDGE APPROACH PAVEMENT REVISION DATE SHEET 1 OF 1 7/12 303.01

RS-3 DIRECTION OF TRAFFIC RAISED PAVEMENT MARKER (SEE NOTE 5) RAISED PAVEMENT MARKER (SEE NOTE 5) CENTERLINE RUMBLE STRIP A A 14" DOUBLE YELLOW CENTERLINE 12" PAVEMENT MARKING DIRECTION OF TRAFFIC PLAN VIEW NOTES 1. CENTERLINE RUMBLE STRIPS SHALL NOT BE INSTALLED WITHIN THE LIMITS OF BRIDGES. 2. CENTERLINE RUMBLE STRIPS SHALL NOT BE INSTALLED ON SUBDIVISION STREETS OR IN NARROW UNMARKED ROAD SECTIONS WITHOUT PAVEMENT MARKINGS. 12.5" R 7" 3. CENTERLINE RUMBLE STRIPS SHALL NOT BE INSTALLED WITHIN THE LIMITS OF CENTER TWO-WAY TURN LANES. 4. CENTERLINE RUMBLE STRIPS SHALL NOT BE INSTALLED IN PASSING ZONES EXCEPT AS DIRECTED BY THE TRAFFIC ENGINEER. THE DEPTH OF CENTERLINE RUMBLE STRIPS IN PASSING ZONES SHALL BE ". 0.5" 5. USE OF RAISED PAVEMENT MARKERS IS OPTIONAL. SEE STANDARD PM-9 FOR DETAILS ON RAISED PAVEMENT MARKER PLACEMENT. WHEN NECESSARY TO ACCOMODATE THE PM-9 STANDARD TWO GROOVES SHALL BE OMITTED EVERY 40 TO ALLOW FOR A CENTERLINE RAISED PAVEMENT MARKER. SECTION A-A 6. WHERE A LEFT-TURN LANE IS MARKED, THE CONTINUOUS CENTERLINE RUMBLE STRIPS SHALL FOLLOW THE DOUBLE YELLOW MARKINGS OF THE OPPOSING LANES AND SHALL STOP 50 FEET FROM THE EDGE OF THE INTERSECTING DRIVEWAY OR ROADWAY. 7. FOLLOWING CUTTING AND CLEANING DEPRESSIONS OF WASTE MATERIAL, THE ENTIRE RUMBLE STRIP AREA SHALL BE COATED WITH LIQUID ASPHALT COATING (EMULSION) USING A PRESSURE DISTRIBUTOR AT AN APPROXIMATE RATE OF 0.1 GALLON PER SQUARE YARD. OVERSPRAY SHALL NOT EXTEND MORE THAN 2 INCHES BEYOND THE WIDTH OF CUT AND/OR SHALL NOT COME IN CONTACT WITH PAVEMENT MARKINGS. 8. PAVEMENT MARKINGS SHALL BE PLACED AS DIRECTED BY THE ENGINEER. CENTERLINE RUMBLE STRIPS SHEET 1 OF 1 304.02 REVISION DATE 310 315

RS-4 DIRECTION OF TRAFFIC PAVEMENT MARKING EDGE OF PAVEMENT A A 12" W (4-0" MIN) 12" EDGE OF PAVED SHOULDER W = WIDTH OF PAVED SHOULDER PLAN VIEW NOTES 1. RUMBLE STRIPES SHALL BE PLACED CONTINUOUSLY AS DIRECTED BY THE ENGINEER. 12.5" R 7" 0.5" 2. 3. RUMBLE STRIPES SHALL NOT BE PLACED WITHIN LIMITS OF BRIDGE DRAINAGE APRONS OR SPECIAL DESIGN SHOULDER SLOT INLETS. RUMBLE STRIPES SHALL BE PLACED ON MAINLINE SHOULDERS ONLY. SECTION A-A 4. 5. FOLLOWING CUTTING AND CLEANING DEPRESSIONS OF WASTE MATERIAL, THE ENTIRE RUMBLE STRIP AREA SHALL BE COATED WITH LIQUID ASPHALT COATING (EMULSION) USING A PRESSURE DISTRIBUTOR AT AN APPROXIMATE RATE OF 0.1 GALLON PER SQUARE YARD. OVERSPRAY SHALL NOT EXTEND MORE THAN 2 INCHES BEYOND THE WIDTH OF CUT AND/OR SHALL NOT COME IN CONTACT WITH PAVEMENT MARKINGS. RUMBLE STRIPES SHALL NOT BE PLACED WITHIN 50 FEET OF ANY INTERSECTION, TURN LANE, ACCELERATION/DECELERATION LANE OR GORE AREA. 6. PAVEMENT MARKINGS SHALL BE PLACED AS DIRECTED BY THE ENGINEER. 310 315 A COPY OF THE ORIGINAL SEALED AND SIGNED STANDARD DRAWING IS ON FILE IN THE CENTRAL OFFICE CONTINUOUS SHOULDER RUMBLE STRIPES REVISION DATE SHEET 1 OF 1 304.03

MB-3 ALL CONCRETE SHALL BE CLASS A3. + " ( ") CHAMFER ALL CORNERS POST MAY BE HOT ROLLED OR WELDED 8" 8" " HOLES TO BE CAST IN POST. " X 2 X 8" X 1-2" 4 4 DEFORMED CHAMFER MAY BE EXTENDED ENTIRE LENGTH OF POST AT THE OPTION OF THE FABRICATOR. BOLT TREATED PINE BLOCK OR RECYCLED MATERIAL # REINF. BARS 4" LESS THAN HEIGHT OF POST 27 " MIN. 28 " MAX. 9-3 GA. WIRE STIRRUPS LAPPED 10", SPACING VARIES 8" 8" 8" 1" CLEAR. 5" TO 1-0" C-C. " 1-2" CHAMFER ON TOP 3-0" 6-0" MIN. OF POST 1-" 7" " X8"X1-2" TREATED PINE BLOCK OR RECYCLED MATERIAL 8" 8" " " DRILL 14" 8" 6-0" MIN. 27 " MIN. 28 " MAX. 1-2" " X 10" BOLT W6X8.5 OR W6X9 " DRILL 7" 1-" X X1-2" TREATED PINE BLOCK OR RE- CYCLED MATERIAL " 14" DIMENSIONS SHOWN IN PARENTHESIS IN- DICATE ACCEPTABLE TOLERANCES. CONCRETE POST OPTIONAL HOLE TO FACILITATE GALVANIZING STEEL POST ALL HOLES IN POST AND BRACKET TO BE " IN DIAMETER. " BLOCKOUT FOR MAINTENANCE REPAIR ONLY 6-0" MIN. 27 " MIN. 28 " MAX. X8"X1-2" TREATED PINE BLOCKS OR RECYCLED MAT L. ALL HOLES IN POST TO BE " DIAMETER. 8" 8" 8" BOLT 1-2" " X 2 GAL. STEEL 10D COMMON NAIL (DRIVE NAIL WITHIN 2" OF THE TOP OR BOTTOM OF BLOCKOUT). NOTES: STANDARD MB-3 POST SPACING IS 6 -. FOR DETAILS OF RAIL ELEMENT, RAIL SPLICE JOINT, W BEAM BACK UP PLATE, AND ASSOCIATED HARDWARE SEE SHEET NO. 501.01. ALTERNATE TYPE POSTS AND BLOCKOUTS MAY BE INTERCHANGED ON ANY ONE PROJECT WITH THE RESTRICTION THAT THE SAME TYPE OF POST AND BLOCKOUT MUST BE USED IN ANY SINGLE RUN OF MEDIAN BARRIER. ALL BOLTS, NUTS, WASHERS, STEEL POSTS, BENT PLATE POST, AND BLOCKOUTS ARE TO BE GALVANIZED. THE GUARDRAIL AND MEDIAN BARRIER COMPONENTS DEPICTED IN A.R.T.B.A. IMPACT ATTENUATOR, CAT, BRAKEMASTER OR STANDARD GR-HDW W BEAM STANDARD WASHERS ARE TO BE USED ON END SECTION (BUFFER). (BUFFER END SECTION MAY ONLY BE USED WHEN LOCATED OUTSIDE OF CLEAR ZONE.) TECHNICAL BULLETIN NUMBER 268B MAY BE SUBSTITUTED IF INTERCHANGEABLE WITH THE STANDARDS FOR GUARDRAIL (GR) OR MEDIAN BARRIER (MB) AND APPROVED BY THE ENGINEER. LAST 50 OF RUN OFF END ONLY. DESIGN SPEED MPH 70 60 50 40 30 FLARE RATES SHY LINE LS INSIDE SHY LINE 9 8 6.5 5 4 FLARE RATE 30:1 26:1 21:1 13:1 7:1 BEYOND SHY LINE 15:1 14:1 11:1 8:1 FLARE RATE SUGGESTED MAXIMUM FLARE RATE FOR SEMI-RIGID BARRIER SYSTEMS. BRIDGE PIER OR OTHER MEDIAN OBSTRUCTION 16:1 SOUTHERN PINE 6-6 - FLARE RATE SEE TABLE. 6X8 WOOD POST METHOD OF TREATMENT AT BRIDGE PIER OR MEDIAN OBSTRUCTION SHEET 1 OF 1 REVISION DATE 502.01 BLOCKED-OUT W-BEAM MEDIAN BARRIER 221 505

FE-W1,W2 CORNER BRACE LINE BRACE LINE BRACE AT END LOCATION W OOD POST PAY LINES (EXCLUSIVE OF FABRIC) "X4" GALV. STEEL DOWEL (EACH END ALL HORIZ. BRACES) 8-0" 8-0" 3-0" 5-0" X X # 9 WIRE TWISTED - FE-W1 12" - FE-W2 X MIN. 4" BRACE THE BRACE WIRE TO BE PLACED AROUND POSTS WITH ONE WIRE ON EACH SIDE OF BRACE. WIRE TO BE DRAWN TAUT BY TWISTING BETWEEN BRACE AND EACH POST. THIS APPLIES TO ALL BRACE WIRES. DIAGONAL 4" BRACES TO BE PLACED IN DIRECTION OF PULL. POST TO BE NOTCHED FOR DIAGONAL 4" BRACES. ALL 4" DIAGONAL BRACES TO HAVE TWO GALVANIZED 12D NAILS EACH END. 5-0" 4"X4" 4 POINT BARBED WIRE X CORNER POST X L2X2X POST WITH 2X2XX7-0" BRACES OR 2" O.D. POST @ 3.65 5% LBS./FT. + - + - WITH 1" O.D. BRACES @ 2.27 5% LBS./FT PAY LINES (EXCLUSIVE OF FABRIC) BRACE POST IF NOT OTHERWISE NOTED DIMENSIONS AND DESCRIPTIONS SHOWN ON ONE DRAWING APPLY TO OTHER DETAILS WITH THE SAME POST TYPE. 8-0" 1 - FE-W1 12" FE-W2 2-12 -0" 8-0" TYPICAL SPACING PAY LINES ALL LINE POSTS GROUND LINE (EXCLUSIVE OF FABRIC) LINE POST 4 POINT BARBED WIRE 3-0" METAL POST 6-0" 12-0" 6-0" 12-0" GROUND LINE 6-0" 6-0" 5"-0" 2-12"X12"X12" CONCRETE BLOCK 5-0" 3-0" 3-0" CORNER POST CONCRETE FOOTING 12"X12"X12" CONCRETE BLOCK 12" STRETCHER POST 12-0" C-C (TYPICAL SPACING BETWEEN ALL LINE POSTS) LINE POST (SEE DETAIL BELOW) NOTES: LINE POSTS ARE TO BE OF THE TYPES SHOWN OR EQUIVALENT MEETING THE SEE GENERAL NOTES- APPROVAL OF THE ENGINEER. FENCING FOR ADDITIONAL DETAILS AND INSTRUCTIONS. ALL POSTS ARE TO HAVE A MINIMUM WEIGHT OF 1.25 LBS./FT. A MINIMUM OF FIVE CLAMPS FOR ATTACHING FABRIC TO POST ARE TO BE INCLUDED IN COST OF EACH LINE POST. L2X2XTO BE CUT TO FIT AROUND L2X2X STRETCHER POST. L2X2X1/4, 2" LONG BRACKET BOLTED TO STRETCHER POST FLANGED FLANGE TYPE "U" TYPE "T" METAL LINE POST FOR USE IN LIEU OF SETTING POSTS IN CONCRETE. DEVICES SHOWN ARE REPRESENTATIONAL ONLY, SEE GENERAL NOTES. ALTERNATE ANCHOR DEVICES ALTERNATE METHOD OF ATTACHING ANGLE BRACES TO STRETCHER POSTS SHEET 1 OF 1 REVISION DATE 503.02 STANDARD FENCE WOVEN WIRE FABRIC 242 507 236

FOR TYPICAL SECTION, NOTES AND OTHER DETAILS, REFER TO STANDARD BCQ-DT. BCQ-10 SPAN HGHT (FT.) (FT.) SIZE SPACING c-c REINFORCING STEEL BT1 a b c d e f g LENGTH NO. BL1 4 BARS NO. BL2 3 BARS REINFORCING STEEL (LBS/LONG. JT) QUAN./LF CONCRETE CLASS A4 (CY/LF) REINFORCING STEEL (LBS/LF) HEADWALL G LENGTH SIZE HW1 LENGTH HEADWALLS NO. HW2 BARS NO. HW3 BARS INLET CONCRETE CL. A4 (CY) INLET REINFORCING STEEL (LBS) OUTLET CONCRETE CL. A4 (CY) OUTLET REINFORCING STEEL (LBS) WINGWALL 3 3 3 4 4 3 4 4 4 5 4 6 5 3 5 4 5 5 5 6 5 7 6 4 6 5 6 6 6 7 6 8 7 4 7 6 7 8 7 10 8 4 8 6 8 8 8 10 9 4 9 6 9 8 9 10 9 12 10 4 10 6 10 8 10 10 10 12 12 6 12 8 12 10 12 12 4 12" 2-8" 0-4" 1-0 - 5" 0-14 -11" 1-5" 15-9" 4 12" 2-8" 0-4" 1-0 - 5" 0-14 -11" 1-5" 15-9" 4 12" 3-0 - 4" 1-11" 0-5" 0-19 - 0" 2-1" 19-9" 4 12" 3-0 - 4" 1-11" 0-5" 0-19 - 0" 2-1" 19-9" 4 12" 3-0 - 4" 1-11" 0-5" 0-19 - 0" 2-1" 19-9" 4 12" 3-0 - 4" 1-11" 0-5" 0-19 - 0" 2-1" 19-9" 4 12" 4-4" 0-4" 2-4" 0-5" 0-23 - 0" 2-8" 23-9" 4 12" 4-4" 0-4" 2-4" 0-5" 0-23 - 0" 2-8" 23-9" 4 12" 4-4" 0-4" 2-4" 0-5" 0-23 - 0" 2-8" 23-9" 4 12" 4-4" 0-4" 2-4" 0-5" 0-23 - 0" 2-8" 23-9" 4 12" 4-4" 0-4" 2-4" 0-5" 0-23 - 0" 2-8" 23-9" 4 12" 5-1" 0-4" 2-9" 0-5" 0-4 12" 5-1" 0-4" 2-9" 0-5" 0-4 12" 5-1" 0-4" 2-9" 0-5" 0-4 12" 5-1" 0-4" 2-9" 0-5" 0-4 12" 5-1" 0-4" 2-9" 0-5" 0-4 12" 5-11" 0-4" 3-1" 0-5" 0-4 12" 5-11" 0-4" 3-1" 0-5" 0-4 12" 5-11" 0-4" 3-1" 0-5" 0-4 11" 5-11" 0-4" 3-1" 0-5" 0-4 11" 6-8" 0-4" 3-0 - 0-4" 34-11" 4 11" 6-8" 0-5" 3-0 - 0-4" 34-11" 4 10" 6-8" 0-5" 3-0 - 0-4" 34-11" 4 9" 6-8" 0-5" 3-5" 0-0 - 4" 34-11" 4 9" 7-0 - 5" 3-10" 0-7" 0-4" 4 9" 7-5" 0-5" 3-10" 0-7" 4 9" 7-5" 0-3 -10" 0-8" 0-5" 4 9" 7-5" 0-3 -10" 0-8" 0-5" 4 8" 7-5" 0-3 - 9" 0-8" 0-5" 4 8" 8-0 - 4-2" 0-8" 0-5" 4 8" 8-0 - 4-2" 0-8" 0-5" 27-0" 3-27 - 9" 108 30100.7701.991253.88928-10" 6 28-3 153.547220.3263.537171.228 C 27-0" 3-27 - 9" 108 40104.3002.114264.64328-10" 6 28-3 183.658230.6803.630171.228 E 27-0" 3-27 - 9" 108 50107.8302.236275.39728-10" 6 28-3 21 3.770241.0343.723171.228 G 27-0" 3-27 - 9" 108 60111.360 2.359287.51228-10" 6 28-3 243.881251.3883.816171.228 I 27-0" 3-27 - 9" 108 70114.890 2.482299.62728-10" 6 28-3 273.992261.7423.908171.228 K 31 - " 3-10" 31-10" 124 30114.130 2.187276.21432-10" 6 32-3 153.952244.3583.955195.260 C 31 - " 3-10" 31-10" 124 50121.190 2.432299.21932-10" 6 32-3 214.174265.0664.141195.260 G 31 - " 3-10" 31-10" 124 70128.250 2.677324.05932-10" 6 32-3 274.397285.7744.326195.260 K 31 - " 3-10" 31-10" 124 90135.310 2.920374.10932-10" 6 32-3 33 4.620306.4824.512195.260 O 4-5" 35-10" 140 30127.490 2.435333.67236-10" 6 36-3 154.334268.3904.351219.292 C 4-5" 35-10" 140 50134.550 2.735345.35736-10" 6 36-3 214.534289.0984.514219.292 G 4-5" 35-10" 140 70141.610 2.979386.26836-10" 6 36-3 274.757309.8064.700219.292 K 4-5" 35-11" 140 90148.670 3.276447.41036-10" 6 36-3 334.957330.5144.863219.292 O 39-0" 5-0" 40-0" 156 30140.8502.812451.84840-10" 6 40-3 154.659292.4224.689243.324 C 0-5" 39-0" 4-11" 40-0" 156 50147.910 3.119459.59840-10" 6 40-3 214.875313.1304.868243.324 H 39-0" 4-11" 40-1" 156 70154.970 3.424492.43240-10" 6 40-3 275.072333.8385.028243.324 L 39-0" 4-11" 40-1" 156 90162.0303.666554.51640-10" 6 40-3 335.295354.5465.213243.324 P 39-0" 4-11" 40-2" 156110169.0903.970599.80440-10" 6 40-3 395.492375.2545.373243.324 T 43-0" 5-44 - 2" 172 30154.210 3.229519.69344-10" 6 44-3 154.985316.4545.028267.356 D 43-0" 5-44 - 2" 172 50161.270 3.541540.82744-10" 6 44-3 215.179337.1625.185267.356 H 4 8" 8-0 - 4-2" 0-9" 0-43 - 0" 5-44 - 172 70168.330 3.853574.37044-10" 6 44-3 275.373357.8705.342267.356 L 4 8" 8-0 - 4-2" 0-9" 0-43 - 0" 5-44 - 172 90175.390 4.094649.61244-10" 6 44-3 335.595378.5785.527267.356 P 5 10" 8-2" 0-7" 4-1" 0-9" 0-6 12" 9-9" 0-8" 4-10" 0-11" 0-7" 6 11" 9-9" 0-8" 4-10" 0-11" 0-7" 5 9" 9-9" 0-8" 4-9" 0-11" 0-7" 5 9" 9-9" 0-8" 4-9" 60 2057.160 1.284141.89916-10" 6 16-3 122.222137.8762.191 99.132 A 60 3060.6901.406152.33916-10" 6 16-3 152.333148.2302.284 99.132 C 76 2070.520 1.479168.50820-10" 6 20-3 122.626161.9082.609123.164 A 76 3074.050 1.602178.94820-10" 6 20-3 152.738172.2622.702123.164 C 76 4077.580 1.724189.38820-10" 6 20-3 182.849182.6162.794123.164 E 76 5081.110 1.847199.82820-10" 6 20-3 21 2.960192.9702.887123.164 G 92 2083.880 1.675195.33924-10" 6 24-3 123.031185.9403.027147.196 A 92 3087.410 1.797205.77924-10" 6 24-3 153.142196.2943.120147.196 C 92 4090.940 1.920216.21924-10" 6 24-3 183.254206.6483.212147.196 E 92 5094.470 2.043226.65924-10" 6 24-3 21 3.365217.0023.305147.196 G 92 6098.0002.165237.09924-10" 6 24-3 243.476227.3563.398147.196 I 43-0" 5-5" 44-172110182.450 4.405688.26444-10" 6 44-3 395.790399.2865.684267.356 T 51 - " 6-52 - 204 50187.990 4.575735.82152-10" 6 52-3 21 5.696385.2265.728315.420 H 51 - " 6-52 - 204 70195.0504.818787.94452-10" 6 52-3 275.918405.9345.914315.420 L 51 - " 6-52 - 7" 204 90202.1105.142811.07252-10" 6 52-3 33 6.106426.6426.065315.420 P 1-0" 0-8" 51 - " 6-52 - 8" 204110209.1705.464873.15652-10" 6 52-3 396.294447.3506.215315.420 T A COPY OF THE ORIGINAL SEALED AND SIGNED DRAWING IS ON FILE IN THE CENTRAL OFFICE. QUADRUPLE BOX CULVERTS 5 TO 10 FT. FILLS REVISION DATE SHEET 2 OF 2 0 1005.10

OSS-1 SPAN STRUCTURE SPAN LENGTH END POLE WIRE INLET (TYPICAL). SEE NOTE 1. SEE SHEET 3 OF 7 WIRE INLET (TYPICAL). SEE NOTE 1 END POLE HAND HOLE AND COVER 4" X 8" MINIMUM TOP OF FOUNDATION 1 - SEE NOTE 3 GUARDRAIL HIGHEST POINT IN ROADWAY VERTICAL CLEARANCE (SEE NOTE 6) SEE SHEET 2 OF 7 SEE NOTE 3 GUARDRAIL HAND HOLE AND COVER 4" X 8" MINIMUM SEE NOTE 7 SEE NOTE 5 EDGE OF SHOULDER SEE NOTE 5 1-0" MIN. SEE NOTE 7 NOTES: CANTILEVER STRUCTURE 1-0"MAX. SEE SHEET 3 OF 7 1. 1 " DIAMETER WIRE INLETS SHALL BE PROVIDED AT THE FOLLOWING LOCATIONS: A. ON SPAN STRUCTURES ON THE FRONT LEG OF END POLE 12" BELOW BOTTOM CHORD. B. ON CANTILEVER STRUCTURES ON POLE 12" BELOW BOTTOM CHORD. C. ON SPAN STRUCTURES BELOW BOTTOM CHORD AT CENTERLINE BEHIND FIRST SIGN PANEL FROM EACH END POLE. D. ON CANTILEVER STRUCTURES BELOW BOTTOM CHORD AT CENTERLINE BEHIND FIRST SIGN PANEL FROM POLE. 2. ALL UNUSED WIRE INLETS SHALL BE CAPPED WATER TIGHT. 3-0" POLE ARM CONNECTION 3. DISTANCE SHALL BE NO LESS THAN THE MINIMUM INDICATED IN GUARDRAIL STANDARDS. POLE TOP OF FOUNDATION 1-1 1/2 " DIAMETER WIRE INLETS INSTALL ON SIDE OPPOSITE TRAFFIC. 1 1/2 " DIAMETER WIRE INLET AT CENTERLINE OF SIGN PANEL, BEHIND FIRST SIGN ONLY. HAND HOLE AND COVER 4" X 8" MINIMUM. SEE NOTE 3 GUARDRAIL HIGHEST POINT IN ROADWAY VERTICAL CLEARANCE (SEE NOTE 6) 4. NO MORTAR, GROUT, OR CONCRETE SHALL BE PLACED BETWEEN BOTTOM OF BASE PLATE AND TOP OF PEDESTAL. 5. THE MAXIMUM SPACE BETWEEN THE BOTTOM OF THE BASE PLATE AND THE TOP OF THE FOUNDATION SHALL BE NO MORE THAN THE DIAMETER OF THE ANCHOR BOLT PLUS ONE INCH. 6.VERTICAL CLEARANCE FOR OVERHEAD SIGN STRUCTURES SHALL BE NO LESS THAN 19 FEET 0 INCH AND NO MORE THAN 21 FEET 0 INCH FROM THE BOTTOM OF THE LOWEST MOUNTED SIGN PANEL TO THE HIGHEST POINT OF THE ROADWAY, UNLESS OTHERWISE SPECIFIED ON THE PLANS. LUMINAIRE ASSEMBLIES SHALL HAVE A VERTICAL CLEARANCE OF NO LESS THAN 17 FEET 6 INCHES FROM THE BOTTOM OF THE ASSEMBLY TO THE HIGHEST POINT OF THE ROADWAY. 7. TOP OF FOUNDATIONS SHALL BE 2-0" MINIMUM ABOVE FINISHED GRADE. FOR FOUNDATIONS ADJACENT OR WITHIN A SIDEWALK, TOP OF FOUNDATIONS SHALL BE A MINIMUM OF ABOVE SEE NOTE 5 FINISHED GRADE. 1-0" SEE N0TE 7 8. FOUNDATIONS SHALL NOT BE LOCATED IN A DRAINAGE DITCH. Min. SHEET 1 OF 7 REVISION DATE 1324.10 A COPY OF THE ORIGINAL SEALED AND SIGNED STANDARD DRAWING IS ON FILE IN THE CENTRAL OFFICE OVERHEAD SIGN STRUCTURE TYPICAL DETAILS 700

OSS-1 TYPICAL SIGN FOOTING DETAIL WITH CONDUIT TOP OF FOUNDATION 8" SIGN POLE 1 " CONDUIT LOCATION OF FUTURE USE CONDUITS FOR DOUBLE END POLE STRUCTURES FINISHED GRADE 4" MINIMUM COVER SPARE CONDUITS 18" MINIMUM GROUNDING ELECTRODE NOTES: THE TYPE, SIZE, NUMBER AND ORIENTATION OF CONDUITS ENTERING AND EXITING FOOTINGS MAY VARY PER SIGN LOCATION. IN ADDITION TO THE CONDUITS SPECIFIED ON THE PLANS, ONE - 1 " CONDUIT REQUIRED FOR GROUND WIRE AND TWO - 2" PVC HEAVY WALL CONDUITS REQUIRED FOR FUTURE USE. FUTURE USE CONDUITS SHALL BE STUBBED OUT AND CAPPED. FUTURE USE CONDUITS SHALL BE ORIENTED TO RUN PARALLEL TO THE ROADWAY. FOR LOCATION OF FUTURE USE CONDUITS IN FOUNDATIONS FOR DOUBLE END POLE STRUCTURES, SEE DRAWING AT RIGHT. FUTURE USE CONDUITS PLACED PARALLEL TO THE ROADWAY EACH FOUNDATION SHALL BE PERMANENTLY MARKED TO INDICATE ALL SIDES FROM WHICH CONDUITS PASS. THIS MARK SHALL BE MADE WITH A TROWEL WHEN FINISHING THE CONCRETE AND SHALL BE 1/4 " DEEP AND 4" TO LONG. LOCATIONS OF EMPTY CONDUITS SHALL HAVE AN ADDITIONAL 2" LONG MARK MADE PERPENDICULAR TO AND CENTERED ON THIS MARK. FUTURE USE CONDUITS PLACED AT AN ANGLE TO MISS THE BACK FOUNDATION OR ANCHOR BOLTS IN A SPREAD FOOTING FOUNDATION. FOUNDATIONS ABOVE FINISHED GRADE SHALL BE CHAMFERED " ON ALL EDGES. GROUNDING BUSHINGS SHALL BE INSTALLED ON EACH END OF METAL CONDUITS. BELL ENDS SHALL BE INSTALLED ON EACH END OF PVC CONDUITS. BELL ENDS & BUSHINGS OF EMPTY CONDUITS SHALL BE PLUGGED TO PREVENT MOISTURE AND RODENT ENTRY. VOIDS REMAINING AFTER CONDUCTORS EXIT OR ENTER BELL ENDS OR BUSHINGS OF CONDUITS SHALL BE SEALED WITH SILICONE TO PREVENT MOISTURE AND RODENT ENTRY. NO MORTAR, GROUT, OR CONCRETE SHALL BE PLACED BETWEEN BOTTOM OF BASE PLATE AND TOP OF FOUNDATION. 700 A COPY OF THE ORIGINAL SEALED AND SIGNED STANDARD DRAWING IS ON FILE IN THE CENTRAL OFFICE OVERHEAD SIGN STRUCTURE FOUNDATION DETAILS REVISION DATE SHEET 4 OF 7 1324.13