BRICK LINTELS STRETCHER COURSE BRICKWORK BRICK LINTELS STRETCHER COURSE BRICKWORK Lintel consist of t lest three courses of bricks bonded with mortr. The first course of bricks, ech verticl joint, hs nchors inserted. Between the first nd the second horizontl sems, nd betyween the second nd the third courses of bricks there is longitudinl rebr reinforcement Murfor -50. The longitudinl rebr t horizontl joints shll go outside the edges of the opening t 50 mm nd 500 mm t the corners of the building. In this wy lintels up to,00 m re mouinted. If bigger pertures need to be mde the sme wy, brcket suspensions GSP or KP-M re used. MAKE Ø, mm, mm Mteril 50-40 -.0 40 zinc coting 50-40 -.0 40 50-5 -.0 5 zinc coting 50-5 -.0 5 50-45 -.0 45 zinc coting 50-45 -.0 45-50* 4.0 50 zinc coting * here nd further the reinforced truss MURFOR mnufcturer NV Bekert SA LINTEL KIT IN BOXES MAKE opening, m Set, pcs. Mteril BL-H-,0.0 BL-H-.5.5 50-40 x 4 50-45 х 50-40 x 50-45 х 4 zinc coting / zinc coting / MOUNTING OF LINTELS UP TO M 4 5 min. 50 mm. ~ cm Construction of formwork Mortr doesnot rech the bottom of the brick bout cm. After lintel mounting nd formwork disssembly the joints shll be fixed Lintel hooks 50-40 in every verticl joint of the first course Reinforcement Murfor -50 is inserted through grooves of lintel hooks Reinforcement rods extend beyond the opening edges by t lest 50 mm in both sides 9 0 Second course of brickwork Mounting of lintel hooks 50-45 Lintel hooks 50-45 in every second verticl joint of the second couse Reinforcement Murfor -50 in the second course of brickwork. Further throughout the height, reinforcement rod t every 00...500 mm Formwork should be dismntled fter weeks. ATTENTION! The bricks of the first course should be full. HERE AND FURTHER. Seeking to rech the nominl strength mking lintels during hot seson, it is recommended to moistened them for weeks. Mortr mrking should be t lest 00
BRICK LINTELS STRETCHER COURSE BRICKWORK LINTEL FROM LONG BRICK Lintel mounting from long brick is nlogous to the lintel mounting from stndrt brick with the ddition of connections SG/, estimting - connections for the brick t the first row. ATTENTION! Before lying bricks the first row, the ends of the bricks shll be processed with primer (qurz bsed). It is necessry for better mortr, brick nd metl dhesion. ATTACHING SG/ CONNECTIONS ON LONG BRICKS At the bck wll grooves re mde (~5 mm wide, ~50 mm long, nd ~5 mm depth) SG/ SG/ connections re introduced into the mortr SG/ connections introduced Lintel hooks 50-40 in every verticl joint of the first course ~5 mm The connections re mrked ~5 mm bove brick surfce msonry rows re reinforced THIN-LAYER DECORATION MASONRY LINTEL MAKE Ø, mm, mm mteril 50-40 -.0 40 zinc coting 50-40 -.0 40 50-45 -.0 45 zinc coting 50-45 -.0 45 SG/ single.0 0-50 4.0 0 zinc coting 4 5 The connections re folded The grooves re filled with mortr MAKE Ø, mm, mm mteril 0-40 -.0 40 0-45 -.0 45-50 4.0 0 zinc coting Mounting of nrrow brick lintel is nlogous to the mounting of lintel from stndrd brick by dditionlly reinforcing one msonry row. The number of reinforced lintel rows t lest rows. ATTENTION! Decortive msonry lyer from bricks 50-5 mm is llowed t low-height construction, up to floors.
BRICK LINTELS SOLDIER COURSE BRICKWORK BRICK LINTELS SOLDIER COURSE BRICKWORK The most common type of lying brick lintels is soldier course brickwork. In this cse the bricks cn be both solid nd hollow. Sometimes, to chieve better effect, first courses of brick lying bove the opening re soldier courses. MAKE Ø, mm, mm Mteril 50-0 -.0 0 zinc coting 50-0 -.0 0 50-45 -.0 45 zinc coting 50-45 -.0 45-50 4.0 50 zinc coting LINTEL KIT IN BOXES MAKE opening, m Set, pcs. Mteril BL-V-.0.0 BL-V-.5.5 50-0 x 50-45 х 4 50-0 x0 50-45 х 5 zinc coting / zinc coting / MOUNTING OF LINTELS UP TO M 4 5 Construction of formwork Bricks re plced on the frmework. Plcement of bricks is mrked on the formwork. Mortr should not rech the bottom of the brick by pproximtely cm. Upon mounting of the lintel nd dismntling of the formwork, joints should be filled in. Lintel hooks 50-0 should be plced into the mortr, in every second verticl joint of the first row of brickwork Reinforcement Murfor -50 should be inserted through grooves of lintel hook min. 50 mm 9 Reinforcement rods extend beyond the opening edges by t lest 50 mm in both sides Lintel hooks 50-45 should be instlled in every second verticl joint of the second row Reinforcement Murfor -50 in the second row of brickwork. Further throughout the height, reinforcement rod in every 00...500 mm Formwork should be dismntled in weeks 4
BRICK LINTELS SOLDIER COURSE BRICKWORK SOLDIER COURSE BRICKWORK WITH ONE AND A HALF BRICK MAKE Ø, mm, mm Mteril 50-0 -.0 0 zinc coting 50-0 -.0 0 50-40 -.0 40 zinc coting 50-40 -.0 40 50-45 -.0 45 zinc coting 50-45 -.0 45-50 4.0 50 zinc coting Lintel mounting t one nd hlf brick is nlogous to the mounting from full bricks. THIN-LAYER DECORATION MASONRY LINTEL MAKE Ø, mm, mm Mteril 0-0 -.0 0 0-45 -.0 45-0 4.0 0 zinc coting Lintel mounting from thin bricks is nlogous to lintelmounting from stndrd bricks with dditionl reinforcement of one brick row. The number of reinforced msonry rows of the lintel shll be t lest rows. ATTENTION! Decortive msonry lyer from bricks 50-5 mm is llowed t low-height construction, up to floors. 5
BRICK LINTELS ROWLOCK COURSE BRICKWORK BRICK LINTELS ROWLOCK COURSE BRICKWORK Rowlock course brickwork is performed t 90 ngle to the fçde becuse doing this it is possible to hide the het insultion lyer behind the decortive brickwork. Depending on the thicknes of this lyer the bottom row of bricks cn protrude from the fçde plne this wy the lintel will be emphsized not only by pttern, but by relief too. K MAKE Ø, mm, mm Mteril 90 K 50-5 -.0 5 zinc coting K 50-5 -.0 5 50-45 -.0 45 zinc coting 50-45 -.0 45-50 4.0 50 zinc coting LINTEL KIT IN BOXES MAKE opening, m Set, pcs. Mteril BL-S-.0.0 BL-S-.5.5 K 50-5 x 50-45 х 4 K 50-5 x0 50-45 х 5 zinc coting / zinc coting / MOUNTING OF LINTELS UP TO M 4 5 min. 50 mm Construction of formwork Bricks re plced on the frmework. Plcement of bricks is mrked on the formwork. Mortr should not rech the bottom of the brick by pproximtely cm. Upon mounting of the lintel nd dismntling of the formwork, joints should be filled in. Lintel hooks K 50-5 should be plced into the mortr, in every second verticl joint of the first row of brickwork Reinforcement Murfor -50 should be inserted through grooves nd shll protrude from the opening for no less thn 50 mm into both sides 9 Lintel hooks 50-45 should be instlled in every second verticl joint of the second row Reinforcement Murfor -50 in the second row of brickwork. Further throughout the height, reinforcement rod in every 00...500 mm OPTION: Lintel with protrusion from the plne of the wll Formwork should be dismntled in weeks.
BRICK LINTELS COMBINED BRICKWORK COMBINED BRICKWORK K MAKE Ø, mm, mm Mteril A clssicl type of brick lintels by ltering full brick nd two identicl hlves. The only importnt condition when selecting combined brickwork is dimensions of the bricks. Their rtio shll be :, e.g. 50х0х5h. The lintel should strt nd finish with soldier course brickwork. The lyout of the lintel is identicl to the lintel mde in the verticl wy. COMBINED BRICKWORK WITH ONE AND A HALF BRICK THIN DECORATION MASONRY LINTEL 90 K K K 50-0 -.0 0 K 50-0 -.0 0 50-45 -.0 45 zinc coting 50-45 -.0 45-50 4.0 50 zinc coting MAKE Ø, mm, mm Mteril K 50-0 -.0 0 50-45 -.0 45 zinc coting 50-45 -.0 45-50 4.0 50 zinc coting MAKE Ø, mm, mm Mteril K 0-40 -.0 40 0-45 -.0 45-0 4.0 0 zinc coting Lintel mounting from thin bricks is nlogous to lintel mounting from stndrd bricks with dditionl reinforcement of one brick row. The number of reinforced msonry rows of the lintel shll be t lest rows. ATTENTION! Decortive msonry lyer from bricks 50-5 mm is llowed t low-height construction, up to floors.
BRICK LINTELS BRICK LINTELS ON BRACKETS BRICK LINTELS ON BRACKETS MASONRY ON THE BRACKETS REINFORCED BY MURFOR In cse of lrge openings (> m), there is risk of deflection s well s destruction of the lintel. In order to void this, suspended brckets GSP should be used. They re fixed to the crrying wll of the reinforced concrete lintel while the free end is inserted into the horizontl joint between the first nd the second rows of brickwork. In this cse, the lod is trnsferred from decortive brickwork to the lod-bering structure through the brckets. Quntity of suspended brckets nd their rrngement bove openings re clculted seprtely in every individul cse. THICKNESS OF THE HORIZONTAL JOINT Mortr Brcket Reinforcement Murfor -50 Reinforcement Murfor -50 Sem with brckets 5 mm Reinforcement Murfor -50 Hook Sem with rebr nd connections 0 mm Hook Thickness of lowered joint with reinforcement nd lintel hooks is to 9 mm. Upon mounting of the reinforcement in the horizontl joint, its thickness should not exceed 0 mm nd in cse of using brckets it should not exceed mm. When plcing reinforcement, there should be no obvious chnges in the thickness of the joint, nd its ppliction should not hve ny influence on the generl ppernce of the brickwork. MOUNTING OF BRICK LINTELS OF OVER M BY USING SPENDED BRACKETS GSP 4 5 min. 50 mm. Construction of formwork Lintel hooks 50-40 in every verticl joint of the first row Connection of truss Murfor -50 with the bottom plte AP- Reinforcement Murfor -50 together with the plte AP- should be inserted through grooves of lintel hooks Fixtion of suspended brcket 9 min. 50 mm. Second row of brickwork A cvity should be cut in the brick bove the brcket nd upon fixtion should be filled with mortr. Reinforcement Murfor -50 in the second nd the third rows of brickwork. Further throughout the height, reinforcement rod in every 00...500 mm Formwork should be dismntled in weeks.
BRICK LINTELS BRICKWORK SPENDED ON BRACKETS BRICKWORK SPENDED ON BRACKETS L 0x50 S 40-0 Mke Ø, mm, mm Mteril S 40-0.0 40 S 40-50.0 40 SX L 50x50 S 40-50 SX - 0.0 0 IMPORTANT! Connections t ech verticl sem. Holes in the brick re mde t plce. SX CORNER OF THE BUILDING L 0x50 S...-0 Mke Ø, mm, mm Mteril U S...-50 L 50x50 U S 5-0.0 5 S 5-0.0 5 S 5-50.0 5 S 0-0.0 0 S 40-0.0 40 SX - 45.0 45 U - 5.0 5 SX IMPORTANT! Connections t ech second verticl sem. Holes in the brick re mde t plce. L 0x50 S...-0 MAKE Ø, mm, mm Mteril L 50x50 90 S...-50 90 S 40/90-0.0 40 S 40/90-50.0 40 S 5/90-0.0 5 S 0/90-0.0 0 S 40/90-0.0 40 SXD - 40.0 40 SXK - 40.0 40 SXK SXD IMPORTANT! Connections t ech second verticl sem. Holes in the brick re mde t plce SXK CORNER OF THE BUILDING SXD It is lso possible to produce non-stndrd hooks for ny vrint of decortive msonry lying. 9