Industrial Pumps fficiency and Reliability
Loctite echnologies for Industrial Pum Most industrial pumps carry a significant capital value and therefore it is important to extend their useful lives and ensure that they run efficiently and reliably. Loctite technologies have been helping OMs around the world prevent common failures and extend end-product life. he same technologies are used by maintenance people in all stages: assembly, installation, repairs, on-going maintenance, and disassembly. Proactive Maintenance can reduce the risk of breakdowns, increase pump reliability, efficiency and longevity, and extend the MBF (Mean ime Between Failures). Prevent fretting and corrosion while securing bearings with Loctite 641 Retaining Compound Make any size gasket with Loctite 518 Flange Sealant Prevent rust and seizure of power end bolts with Loctite Marine Grade nti-seize Prevent Key wallow with Loctite 243 Medium Strength hreadlocker or repair key wallow with Loctite 660 Quick Metal Retaining Compound Prevent set screws from working loose with Loctite 222 hreadlocker or Loctite 243 hreadlocker Secure and prevent leakage between oil seals and housing with Loctite 243 Medium Strength hreadlocker or Loctite 248 Medium Strength hreadlocker Sticker Seal threaded fittings with Loctite 567 PS hread Sealant with PF Keep mounting bolts tight with Loctite 271 High Strength hreadlocker
ps Rebuild and Maintenance Goulds 3196 pump was used to demonstrate Loctite solutions to common failures and challenges. Similar solutions will apply to other types and brands of industrial pumps. he environments in which these pumps operate, not necessarily pump construction, can affect pump operation and efficiency and present challenges to end users. here are more Loctite solutions available than depicted below. Please contact Loctite to discuss your specific application needs. Protect pump against chemical attack and errosion with Loctite Nordbak Chemical Resistant Coatings Rebuild and protect worn volutes with Loctite Nordbak Wearing Compound and/or Loctite Nordbak Brushable Ceramic Restore, coat and protect impeller vanes with Loctite Nordbak Brushable Ceramic Prevent corrosion and seizure of gland assembly nuts and seizure of the impeller to the shaft with Loctite Marine Grade nti-seize Rebuild worn shafts with Loctite Fixmaster Superior Metal Seal and protect flushing connectors with Loctite 567 PS hread Sealant with PF Prevent corrosion and secure casing bolts and adapter bolts with Loctite 243 Medium Strength hreadlocker Provide a solid mounting base with Loctite Fixmaster Super Grout
Loctite echnologies - Improve Industrial Pumps fficiency and Reliability Loctite technologies have improved efficiency and reliability of industrial pumps, new and old. he following test shows that after coated by Loctite Nordbak Brushable Ceramic, Pump fficiency increased by +4.8% from 82.4% to 87.2%, ot. Head increased by +4% from 29.5 mtr to 30.68 mtr, Power Input reduced from 72.31 kw to 69.00 kw. *Q=200 l/sec Original Pump Curve nd Suction Pump usgpm 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400 igpm 0 400 800 1200 1600 2000 2400 2800 3200 3600 42.5 MXIMUM POWR 70.56 kw SPD: 1475 R.P.M. 40 40% 50% 60% 342 37.5 70% INL DI.: 250 mm 76% 35 DISCH DI.: 200 mm O 325 80% 32.5 No. 4 SHF MODUL 82% L 30 308 27.5 H 82% 291 25 80% 22.5 D 274 76% 20 IMPLLR DI. - mm 70% ~ 17.5 60% M 15 12.5 R 10 50% 55 kw S 7.5 45 kw 8 37 kw NPSHR NPSHR 274mm 6 342mm 4 metres 2 120 O 110 100 L 90 H 80 70 D 60 ~ 50 F 40 l/sec 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 m³/hr 0 100 200 300 400 500 600 700 800 900 1000 VOLUMRIC FLOWR D FOR CLN COLD WR ONLY PUMP PRFORMNC O S2417 GRD 2 PUMP MODL CURV No. SHJ504 250x200-315 D 19-01-04 130 30 20 ISSU 2 Pump Curve after Coated by Loctite Nordbak 40 35 30 otal H ead 25 -m P U M P S N o:22k 2005 19 S O U H R N C R O S S 250X 200-315 342m m 1475rpm D :23/11/2005 87.2% S2417 Grade 2 90 80 P um p ffic. 70 -% 60 20 15 10 69 kw 50 P um p Input 80 Power -kw 60 5 40 0 20 0 25 50 75 100 125 150 175 200 225 250 275 300 325 Flow rate -l/se c Pump fficiency est Data Pump Make: SOUHRN CROSS Pump Size: 250X200-315 Pump Serial No.: 22K200519 Duty Flow Required (l/s): 200 Duty Head Required (m): 29.5 Duty fficiency Req'd (%): 82.4 Pump ype: ISO PRO Impeller Dia. (mm): 342.0 Pump Speed: 1,475 Suction Pipe Dia. (mm): 262 Discharge Pipe Dia. (mm): 209 Gauge Height Correction (m): 0.7 Dynamometer size (kw): 250 No Load Reading: 1.20 Units l/s m mh²o kg m m m kw kw % Flowrate Disch. Gauge Suct. Mano. Dyna. Load Suct. Head Vel. Head ot. Head Water kw Input kw fficiency 0.00 37.00 0.00 52.50 0.00 0.00 37.70 0.00 43.65 0.00 80.00 36.00 2.35 63.30 2.35 0.16 39.21 30.76 52.84 58.22 120.62 34.50 2.55 70.60 2.55 0.38 38.13 45.09 59.05 76.37 160.00 30.50 2.95 77.40 2.95 0.66 34.81 54.62 64.83 84.24 180.59 28.40 3.05 80.10 3.05 0.84 32.99 58.42 67.13 87.03 200.00 25.60 3.35 82.30 3.35 1.03 30.68 60.17 69.00 87.20 220.12 22.50 3.55 84.30 3.55 1.25 28.00 60.44 70.70 85.48 240.47 19.20 4.15 85.70 4.15 1.49 25.54 60.23 71.90 83.77 260.00 10.50 4.05 77.10 4.05 1.74 16.99 43.32 64.58 67.09
Loctite Maintenance Workshop - what you need to improve pump efficiency and reliability By applying the identified product solutions and techniques learned in Loctite Maintenance Workshop, your personnel will have the knowledge and the tools to rebuild and maintain your pumps to improved efficiency and reliability. Please call Loctite today to schedule a workshop tailored for you! he majority of unplanned downtime is caused by mechanical subcomponent failure. Some taproots reasons are: fastener loosening, key wallow, PF tape fouling control valves, fitting leakage and spun bearings. his workshop teaches how to prevent these from happening proactively. Manufacturing Reliability Workshop hreadlocking How a threaded fastener works dvantages and disadvantages of mechanical locking devices Loctite hreadlockers - How they work - Benefits - pplication cases and application techniques hread Sealing ypes of threads and fittings Causes of leaks Loctite hread Sealants - How they work - Benefits - pplication cases and application techniques Gasketing Why gaskets leak - Design and service factors - Gasket materials and dressings - ssembly problems Form-in-place gasketing basics Loctite naerobic and Silicone (RV) Gasketing - How they work & benefits - pplication cases and application techniques Retaining ypes, classes, and typical uses of cylindrical fittings Potential fit problems and possible solutions Loctite Retaining Compounds - How they work - Benefits - pplication cases and application techniques Surface ngineering Workshop Much of the destruction of plant and equipment is a direct result of the continual and incremental degradation of a surface that eventually result in structural failure. Surface preparation is critical to enable the composite to stay fixed in place onto the substrate in order to perform at its designed specifications. Wear / brasion Wear / abrasion raditional methods to prevent and repair wear / abrasion Wear resistant polymer composites dissected How wear and abrasion affect metal surfaces and surface dynamics dvantages of wear resistant polymer composites versus traditional Corrosion / rosion Corrosion / erosion cycle Reasons for and types of coating delamination raditional methods for corrosion / erosion / chemical attack Polymer composites and their role in Surface ngineering Maintenance Solutions Workshop Provides repair, rebuild, reclaim and protection methods to metal, concrete and rubber (elastomeric) surfaces. ssist industry in preserving and extending the life of plant and equipment. Bonding Repair broken parts ssemble parts quickly and easily Make bonds that are stronger than mechanical methods nti-slip raction System Prevent slips and falls with anti-slip floor systems Reduce accidents in the workplace Concrete Repair & Grouting Use composite to avoid popping and cracking of concrete bases Repair common building materials such as concrete, wood, metals, brick Increase impact and chemical resistance nti-seize Protect against rust, corrosion, seizing, and galling Provide lubrication in extreme environments
Henkel Your Partner Worldwide... Henkel sia-pacific Headquarter Henkel (China) Co. Ltd 1001-1004, 10/F, Gangtai Plaza 700 Yan n Road ast, Shanghai, 200001 P.R. China el: +86-21-5385-0165 Fax: +86-21-6360-0699/ +86-21-6360-6070 Henkel ustralia Pty Ltd. 135-141 Canterbury Road Kilsyth, Victoria 3137 ustralia el: +61-3-9728-7200 Fax: +61-3-9728-3986 Henkel Loctite (China) Co., Ltd. Shanghai Office 3F ast Ocean Center 618 Yan n ast Road Shanghai 200001 P.R.China el: +86-21-5353-4595 Fax: +86-21-5985-4246 Henkel Hong Kong Limited 18/F, Island Place ower 510 King's Road, North Point, Hong Kong el: +852-2233-0000 Fax: +852-2802-9995 Henkel Loctite India Pvt. Ltd. 1, irport Service Road Domlur Layout, Bangalore 560 071 India el: +91-80-2535-7771 Fax: +91-80-2535-7770 P Henkel Indonesien Jl. Raya Jakarta-Bogor KM 31.2 Cimanggis-Depok 16953 Indonesia el: +62-21-8775-2196 Fax: +62-21-870-1823 Henkel Japan Ltd. Henkel echnology Center-sia-Pacific 27-7 Shin Isogo-Cho Isogo-ku Yokohama 235-0017 Japan el: +81-45-758-1800 Fax: +81-45-758-1851 Henkel Loctite Korea, Ltd. 8th Floor, Mapo ower, 418 Mapo-Dong, Mapo-ku, Seoul, 121-734 Korea el: +82-2-3279-1700 Fax: +82-2-3273-4663 Henkel (Malaysia) Sdn Bhd level 46, Menara M Jalan Pantai Baharu 59200 Kuala Lumpur el: +603-2246-1000 Fax: +603-2246-1188 Henkel New Zealand Ltd. 2 llens Road ast amaki uckland, New Zealand el: +64-9-272-6710 Fax: +64-9-272-6711 Henkel Philippines, Inc. 21/F sian Star Building 2402-2404 sean Drive Filinvest Corporate City labang Muntinlupa City 1781 Philippines el: +632-859-3100 to 3101 Fax: +632-807-4498 / 807-6844 Henkel Singapore Pte Ltd. Haw Par echnocentre #03-01/02 401 Commonwealth Drive Singapore 149598 el: +65-6266-0100 Fax: +65-6266-1161 Henkel aiwan Ltd. 10F, 886, Chung Cheng Road Chung Ho City aipei Country 23586 aiwan el: +886-2-2227-1988 Fax: +886-2-2226-8699 Henkel (hailand) Ltd. he offices at Centralworld, 35/F, 999/9 Rama 1 Road., Kwang Patumwan, Khet Patumwan Bangkok 10330 el: +66-2-209-8000 Fax: +66-2-209-8008 Henkel W/W Headquarter Henkel KGa Henkelstr.67, D-40589, Dusseldorf el: +49-211-797-0 Fax: +49-211-798-2358 ll trademarks, except where otherwise noted, are the property of or used under license by Henkel Corporation. Copyright 2006. Henkel Corporation. ll rights reserved. www.loctite.com www.henkel.com PHQ-IL-158 (07/2006)