Shed Model: J305MK FRONT BASE LENGTH: 3.0m SIDE BASE LENGTH:.5m FRONT WALL HEIGHT:.80m REAR WALL HEIGHT:.08m 60mm SLAB WIDTH CONCRETE SLAB 300mm SLAB LENGTH We thank you for choosng an Australan Made Shed. At GARDENPRO we want to here what you thnk about our products and nstructons. We love feedback!. Please contact us at feedback@gardenpro.com.au. TOOLS REQUIRED OPTIONAL OPTIONAL GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 0
GENERAL INSTRUCTIONS Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. Gardenpro Masterstore Seres Shed Model: J305MK It s recommended that the shed be set on a 00mm concrete slab and anchored down approprately (refer FINAL CONSTRUCTION page for detals). Anchor sets are suppled as standard tems wth ths product. IMPORTANT: WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED 50mm A NOTE ON SAFETY Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 0
Shed Model: J305MK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS PACKED IN TWO LARGE CARTONS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK STEEL SHEET 045 X 773mm 6 STEEL SHEET 95mm X 773mm 60L STEEL SHEET 045 X 773mm 63 STEEL SHEET 95mm X 773mm 60R STEEL SHEET 045mm X 773mm 6L 4 STEEL SHEET 60mm X 773mm 43S STEEL SHEET 045mm X 773mm 6R STEEL SHEET 785mm X 7mm 34A STEEL SHEET A 75mm X 773mm STEEL SHEET 75mm X 773mm B J305MCP SET (SEE PAGES 4 & 5) INSTRUCTIONS & FITTINGS PACKET (SEE PAGE 5) GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 03
Shed Model: J305MK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK L = 496.5mm (58.9") 55AL L = 496.5mm (58.9") 55AR L = 496.5mm (58.9") 55CL L = 496.5mm (58.9") 55CR L = 496.5mm (58.9") 55BL L = 496.5mm (58.9") 55BR L = 496.5mm (58.9") 8BL L = 496.5mm (58.9") 8BR L = 496.5mm (58.9") 8AL L = 496.5mm (58.9") 8AR L = 530mm 6D L = 75mm 58B L = 568mm 79A 4 L = 773mm 58C L = 53mm 8E WITH HINGES L = 75mm 58A GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 04
Shed Model: J305MK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS PACKED IN TWO LARGE CARTONS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK JAMB L= 785mm 89A 4 JAMB L= 0mm 9A JAMB L= 75mm 89C LIP TRIM L= 60mm 88J JAMB L= 568mm 90A INSTRUCTIONS & FITTINGS PACKET ASSEMBLY INSTRUCTIONS DOUBLE DOOR FITTINGS PACK PSTKDBL 6 JOINER L= 00mm (7.9") CSJ PSTKDBL - DOUBLE DOOR FITTINGS PACK DOOR STRAP L: 65mm A 3 DOOR PADBOLT FAST006 DOOR PADBOLT HASP FAST007 3mm DRILL BIT DRILL PHILLIPS DRIVER BIT FAST038 SELF TAPPING SCREWS PACKET CONTAINING 0 PACKP SCREW PACK PACKP - SCREW PACK 8 3/6 ROUND HEAD BOLTS & NYLOCK NUTS 3. x 8mm BLIND POP RIVETS 3/6 COUNTERSUNK SCREWS & NUTS GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 05
Shed Model: J305MK INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP. Poston the channels and the CSJ joner channel so the center of the CSJ s n lne wth the end of each channel to be joned together. STEP. Jon the frst channel to the CSJ by nsertng the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text s marked. Push down one sde of the CSJ untl you hear a 'clck'. = = JOIN>> <<JOIN JOIN>> = <<JOIN = DRILL 4 x 3mm ( PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) STEP 3. Jon the second channel to the CSJ by postonng the <<JOIN end of the channel at the center of the CSJ (on an angle). Push the CSJ nto the channel untl you here a 'clck'. FINISHED The joned channels should now look lke the pcture above wth the CSJ postoned equally nsde of the joned channels. PUSH QTY = 0pcs. CSJ PUSH CSJ CSJ CSJ HIGH-SIDE CSJ LOW-SIDE 0mm 5mm CSJ GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 06
Shed Model: J305MK STEP. PRE-ASSEMBLY OF SPLICED S NOTE: JOIN TOGETHER X SECTIONS USING 6 X JOINERS (PART CSJ) X 8AR X 8AL X 55AR X 55AL X 55CR X 55CL NOTE: SOME S HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY WHERE THE CSJ JOINING COVERS HOLES ON THE S YOU ARE CONNECTING 993mm 8AR 8AL 55CL 55AR 55AL 55CR 8BL 55BR 55BL = = = = = x 8A x 55A x 55C x 55B x 8B X 55BR X 55BL 8BR X 8BR X 8BL GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 07
88J VIEW OF ROOF COMPONENTS 8A 43S 43S 43S 43S 8A 88J NO. NO. Gardenpro Masterstore Seres Shed Model: J305MK GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 08
Shed Model: J305MK 55B 63 6 6R 8B 8E VIEW OF WALL COMPONENTS 63 6D A 60R 6 34A 90A 89A 55C 9A 6L 89A 9A 79A 6D 60L 34A A 55A 8E B GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 09
Shed Model: J305MK ASSEMBLY INTRODUCTION The snap-tte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. NOTE: The 'hgh sde' s always on the nsde of the shed. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. PUSH Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS HIGH SIDE Each permeter channel must fnsh flush wth the edges of the sheets. the snap-tte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed 3mm POP RIVETS 4mm NUT & BOLT SET Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 0
Shed Model: J305MK DOOR PANEL ASSEMBLY 58C 58C 58A 58B B A A 58C 58A 58C 89C B A 0mm FLANGE 5mm FLANGE FOUR HOLE SET FOR PADBOLT CONNECTION GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE
Shed Model: J305MK REAR PANEL ASSEMBLY 6 63 63 6 55B 8B GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE
Shed Model: J305MK SIDE PANEL ASSEMBLY x LEFT SIDE PANEL x RIGHT SIDE PANEL 60R 6R 6L 60L 6D 8E 6D 8E GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 3
Shed Model: J305MK ROOF PANEL ASSEMBLY 43S 43S 43S 43S 8A 88J 8A 88J GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 4
Shed Model: J305MK FRONT PANEL ASSEMBLY 89A 89A 34A 34A 55A 90A 79A SNAP T SNAP TE T TE 55C GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 5
Shed Model: J305MK DOOR PANEL ASSEMBLY 9A 9A B A NOTE: Nuts and bolts (suppled) may be used nstead of pop rvets (suppled) by smply enlargng the hnge hole sets n the jamb usng a 4mm drll bt NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. poston each hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 6
Shed Model: J305MK PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not postoned upsde down. The top channel of each panel s pre-punched for attachng roof sheet. The base channels are not pre-punched. SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 7
Shed Model: J305MK FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 8
Shed Model: J305MK AUSTRALIAN PRODUCT WARRANTY AGAINST DEFECTS Congratulatons on your purchase of an GARDENPRO SHED GARDENPRO SHEDS, ncludng garden sheds, garden beds, avares, storage unts, garages, awnngs and carports are made usng hgh qualty Australan made steel. We are pleased to advse we warrant that the steel coatng wll not rust, crack, flake peel or blster for 0 years from date of purchase, when nstalled wthn Australa. Ths warranty does not apply to surface deteroraton of panels caused by 'Swarf (Tny partcles of steel debrs left from cuttng, grndng or drllng operatons) that has not been removed after buldng constructon, or as a result of contact wth damp sol, chemcals, fertlsers or other corrosve substances. Ths warranty covers any GARDENPRO product used for normal domestc use and nstalled n accordance wth the nstallaton nstructons. The warranty does NOT cover Damage caused by storms, wnd, ran snow or poor foundatons. Ths warranty does NOT cover GARDENPRO products nstalled n severe coastal, ndustral or other hghly corrosve envronments. The warranty does not cover fasteners (screws, nuts, bolts, rvets, hasps or bolts). The warranty s lmted to replacement and delvery of components and does not nclude any labour or nstallaton costs. The benefts gven by the warranty are n addton to your other rghts and remedes under a law n relaton to the goods or servces to whch the warranty relates. The warranty apples to the excluson of all other representatons, guarantees or warrantes express or mpled, our goods come wth guarantees that cannot be excluded under the Australan consumer law and s not transferable. You are enttled to a replacement or refund for a major falure and for compensaton for any other foreseeable loss or damage. You are also enttled to have the goods repared or replaced f the goods fal to be of an acceptable qualty and the falure does not amount to a major falure. For further nformaton go to http://www.consumerlaw.gov.au. Please retan a proof of purchase (sales docket or nvoce) or regster your warranty wthn 30 days of purchase here: http://gardenprosheds.com.au/regster-warranty/ In the unlkely event a warranty clam s made, t must be supported by photographc evdence and detals of the defect, ncludng component part numbers, together wth proof of purchase documentaton (or on-lne regstraton of purchase) and forwarded to the address below. Upon recept of the warranty clam, the Customer Servce Manager wll contact you wthn three busness days to advse you of the assessment outcome of the clam, whch may nclude your expenses ncurred n makng the clam. THE CUSTOMER SERVICE MANAGER, GARDENPRO INDUSTRIES, PO BOX 9 ACACIA RIDGE QLD AUSTRALIA 40 PHONE: 800-09-70--------FAX: 07-3344-9--------EMAIL: warranty@gardenpro.com.au Issued 0 September 07 GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 9
Shed Model: J305MK GARDENPRO SHEDS - STORAGE GUIDELINES GARDENPRO SHEDS nclude garden sheds, garden beds, storage unts, avares, garages, awnngs and carports. GARDENPRO SHEDS are desgned to be weatherproof for normal weather condtons. In the event of extreme weather condtons such as heavy ran, combned wth hgh wnd gusts, the rdge cappng, sheetng jons, screw fxngs etc., may exhbt mnor deformatons whch may allow some water entry. These areas should be checked regularly to ensure that maxmum strength and protecton s mantaned. Other weather condtons such as extreme heat and extreme cold, most or dry ar can nfluence the effects of concrete floor mosture and/or condensaton on the undersde of the roof sheets. GARDENPRO SHEDS and storage unts are prmarly used for storage of garden equpment such as lawnmowers, wheelbarrows, garden tools etc. Storage tems that mght be adversely affected by any of the above condtons may requre addtonal protecton such as beng sealed or covered by plastc sheets and/or stacked above the concrete floor on tmber slats. Waterproof sealants may be used to offer further protecton where requred around jons and screw fxngs, as can rubber door seals and other products whch are avalable from most hardware outlets. Placement of waterproof sealants (slcone) between the base of the shed and concrete slab s not recommended, as ths process can have a reverse effect, preventng excess water from escapng, resultng wth water accumulatng and beng trapped nsde the shed. GARDENPRO accepts no responsblty for water entry, floor mosture, condensaton or the condton of the Contents nsde your GARDENPRO steel buldng arsng from any of the pre-mentoned weather condtons. GARDENPRO ASSEMBLY INSTRUCTION MANUAL SHED MODEL: J305MK 06-0-07 PAGE 0