Submittal Sheet 09210 Imperial Gypsum Base Regular Core Gypsum Base Tapered Edge A large size, rigid base for economical application of gypsum veneer plasters Special gypsum core and multi-layered laminated face paper to control water absorption, provide maximum plaster bond and resist sag. Panels are designed for direct or resilient attachment to wood or steel framing. Imperial brand bases comply with ASTM C1396/C1396M and have gypsum cores UL-Classified as non-combustible per ASTM E136. Description Limitations Imperial gypsum base is ideally suited for veneer plaster systems. Available in 1/2" thickness, 4' and 54" widths by 8' to 14' lengths. The distinctive blue face paper is designed to provide the qualities desirable for veneer plaster applications, that is, it controls water absorption, provides for a strong plaster bond and resists plaster slide. The panels provide a rigid base that resists sag. When securely attached, gypsum base adds lateral stability to the assembly. Also, gypsum base partitions faced with gypsum plaster on both sides have high resistance to sound transmission. Resilient attachment further improves ratings. These panels are not affected by decay, dry rot or normal moisture; they will not attract vermin. Imperial gypsum base is designed to be used with the following plaster products: Imperial veneer finish, Diamond brand veneer finish, USG Norfolk Special veneer finish, Imperial veneer basecoat and Diamond veneer basecoat. 1. Imperial gypsum bases should only be used with veneer plaster products. 2. Imperial gypsum bases should not be used in areas exposed to excessive moisture for extended periods or as a base for adhesive application of ceramic tile (Sheetrock brand Mold Tough gypsum panels or Durock brand cement board are recommended for this use). 3. Do not apply Diamond veneer finish, or any lime containing finish plaster to Imperial gypsum base that has faded from exposure to sunlight. Where fading has occurred, treat surface with either USG plaster bonder or a spray-applied solution of USG accelerator-alum catalyst before application of finish. 4. Gypsum base surfaces should be isolated with control joints or other means where: (a) Partition or furring abuts a structural element (except floor) or dissimilar wall or ceiling; (b) Ceiling abuts a structural element, dissimilar wall or partition, or other vertical penetration; (c) Construction changes within the plane of the partition or ceiling; (d) Partitions or furring run exceeds 30'; (e) Ceiling dimensions exceed 30' without relief, or 50' with relief; (f) Expansion or control joints occur in the base exterior wall. Ceiling-height door frames may be used as control joints, as may door frames that are less than ceiling height, if control joints extend to ceiling from both corners. 5. Do not exceed the maximum spacing of framing members shown in the table below. Maximum spacing of framing members for new construction: base and finish assembly framing spacing (1) in. mm in. mm 1/2 12.7 Imperial gypsum base one layer, 1-coat system 16 406.4 one layer, 2-coat system 16 or 24 (2) 406.4 or 609.6 (2) two layer, 1 & 2-coat system 24 609.6 (1) For perpendicular or parallel application to framing. Perpendicular is preferred for maximum strength; parallel application is not recommended for ceilings. (2) 24" (609.6 mm) spacing requires joint treatment with Sheetrock joint tape and Sheetrock setting-type joint compound (Durabond or Easy Sand ).
Directions Preparation Protect the product from moisture during storage and on the job. In cold weather, heat the interior of the building to a minimum of 55 F (13 C) for an adequate period before the application of plaster, while basecoat and finish is being applied, and until the finish is dry. Air circulation should be kept at a minimum level during this period. Warning: Store all Imperial gypsum base flat. Panels are heavy and can fall over, causing serious injury or death. Do not move unless authorized. Under normal working conditions, joints of veneer plaster systems may be treated by applying Imperial tape Type P (pressure-sensitive) or Type S (staple) to the joints and then applying the veneer plaster basecoat or finish to preset the tape. However, there are a number of special situations that require the use of a setting-type joint treatment system. High building temperature, low humidity or excessive evaporation that creates rapid drying conditions. Metal framing is specified. Certain wood-framing applications with spacing of 24" o.c. (see Maximum Spacing table above). Under any of these conditions, use Sheetrock joint tape and Sheetrock setting-type (Durabond) or lightweight settingtype (Easy Sand) joint compound to treat all joints and internal angles. Allow the joint treatment to set and dry thoroughly before plaster application. Installation Imperial gypsum base may be installed either perpendicular (preferred) or parallel to the framing. All ends and edges should be placed over framing members except where edge joints are perpendicular to framing. Use maximum practical lengths to minimize end joints. Install gypsum base first on ceilings and then on walls. Over steel studs, arrange direction of installation so that the lead edge of the base is attached to the open side of the stud flange first. Bring base panels into contact with each other, but do not force into place. Fit abutting ends and edges neatly; stagger end joints; arrange joints on opposite sides of partition so they occur on different studs. Begin driving fasteners in center of panel and work toward ends and edges, holding gypsum base in firm contact with framing. Space fasteners as shown in table and not less than 3/8" from edges and ends of panel. Drive fastener heads flush with surface without breaking the face paper. If gypsum base appears to be loose from framing, install additional fasteners. Float vertical and horizontal interior corners by placing fasteners 8" out from the corner. Where framing is parallel with the corner, attach one panel to corner framing and float the abutting panel. Cut and fit gypsum base neatly around pipes and other openings. Remove loose face paper around cuts and use quick-setting plaster to close openings. Control Joints Apply control joints, where required, over the face of the gypsum base. Cut to required lengths with finetoothed hack saw. Cut end joints square, align and butt together slightly gapped. Attach the control joint to gypsum base temporarily with 9/16" rosin-coated staples spaced 12" o.c. along each flange. Complete the installation of the control joint with fasteners (nails or screws) driven through the control joint flange into the framing on each side of the joint. The protective plastic tape over the open groove should be left in place until finishing is completed. Metal Trim Fasten gypsum base in normal manner but omit fasteners at framing member where metal trim is to be installed. Leave a space 3/8" to 1/2" wide between edge of base and face of jamb or wall. This provides space for hardware or door bucks and allows for expansion when trim is used for perimeter isolation. Slip trim over edge of base with expanded mesh flange on face side. Fasten to base by nailing or stapling 12" o.c. Vinyl Trim Slip vinyl trim over gypsum base with long flange behind base. Install the base with the trim firmly abutting the surface. Corner Bead Apply to all external angles. Hold tightly against angle and fasten to base by nailing or stapling 12" o.c. alternately on both flanges along entire length. Acoustical Sealant Seal edges of gypsum base around entire perimeter of partition. Also, seal air-tight all penetrations of the gypsum base, particularly electrical boxes. In addition to sealing the perimeter of electrical boxes, coat the back sides with a layer of acoustical sealant. Apply acoustical sealant under control joints and similar openings between the gypsum base and abutting materials.
Product Data Materials: Panels with gypsum core, paper encased, square or taped edges. Compliance with Standards: Imperial gypsum base meets ASTM Designation C1396/C1396M. Thermal coefficient of expansion (unrestrained): 9.2x10 6 in./in. x F (40-100 F); 16.2 mm/km x C (4-38 C). Thermal resistance value: R = 0.45 (1/2" base), 0.56 (5/8" base). Hygrometric coefficient of expansion (unrestrained): 7.2x10 6 in./in. x F (7.2 mm/km x C) at 5-90% R.H. Storage: Store material in a cool, dry place. Avoid direct sunlight. Maintain temperature above 40 F (4 C). Availability and Cost: Imperial gypsum base is distributed throughout the United States. Contact a United States Gypsum Company sales office or sales person for additional information. Types, sizes, packaging and weights: Approximate weight Thickness Width Length Pc./ lb./ kg/ Product in. mm in. mm ft. mm bdl. 1000ft. 2 100m 2 Imperial Base Regular Core 1/2 12.7 48 1219.2 8 to 2 1820 890 Submittal Approvals: Job Name Contractor Date Trademarks The following trademarks used herein are owned by United States Gypsum Company: Diamond, Durabond, Durock, Easy Sand, Imperial, Mold Tough, Sheetrock, USG, USG in stylized letters. Note Products described here may not be available in all geographic markets. Consult your United States Gypsum Company sales office or representative for information. Notice We shall not be liable for incidental and consequential damages, directly or indirectly sustained, nor for any loss caused by application of these goods not in accordance with current printed instructions or for other than the intended use. Our liability is expressly limited to replacement of defective goods. Any claim shall be deemed waived unless made in writing to us within thirty (30) days from date it was or reasonably should have been discovered. Safety First! Follow good safety and industrial hygiene practices during handling and installing products and systems. Take necessary precautions and wear the appropriate personal protective equipment as needed. Read material safety data sheets and related literature on products before specification and/or installation. Manufactured by United States Gypsum Company 550 West Adams Street Chicago, IL 60661 800 USG.4YOU (874-4968) usg.com P782/rev. 4-11 2011, United States Gypsum Company Printed in U.S.A.
Submittal Sheet 09210 Imperial Gypsum Base, (Firecode and Firecode C Core) FIRECODE CORE Type X FIRECODE C CORE Type X Gypsum Base Tapered Edge Gypsum Base Tapered Edge A large size, rigid base for fire-rated gypsum veneer plaster systems UL-Listed fire-rated veneer plaster systems. Special gypsum core and multi-layered laminated face paper to control water absorption, provide maximum plaster bond and resist sag. Panels are designed for direct or resilient attachment to wood or steel framing. Imperial brand bases comply with ASTM C1396/1396M and have gypsum cores UL-Classified as non-combustible per ASTM E136. 5/8 in Type X with Firecode Core. 1/2 in and 5/8 improved Type X with Firecode C Core. Description Limitations Imperial gypsum base, Firecode and Firecode C cores, are ideally suited for fire-rated veneer plaster systems. Available in a variety of sizes, the panels are large enough to be installed like drywall panels. The distinctive blue face paper is designed to provide the qualities desirable for veneer plaster applications, that is, it controls water absorption, provides for a strong plaster bond and resists plaster slide. The panels provide a rigid base that resists sag. When securely attached, gypsum base adds lateral stability to the assembly. Also, gypsum base partitions faced with veneer plaster on both sides have high resistance to sound transmission. Resilient attachment further improves ratings. These panels are not affected by decay, dry rot or normal moisture; they will not attract vermin. Firecode core Imperial gypsum base is 5/8" thick and provides Type X fire-resistant performance. Firecode C core Imperial gypsum base in 1/2" and 5/8" thicknesses provides the highest levels of fire-resistant performance. Imperial gypsum base is designed to be used with the following plaster products: Imperial veneer finish, Diamond brand veneer finish, USG Norfolk Special veneer finish, Imperial veneer basecoat and Diamond veneer basecoat. 1. Imperial gypsum bases should only be used with veneer plaster products. 2. Imperial gypsum bases should not be used in areas exposed to excessive moisture for extended periods or as a base for adhesive application of ceramic tile (Sheetrock brand Mold Tough gypsum panels, or Durock brand cement board are recommended for this use). 3. Do not apply Diamond veneer finish, or any lime containing finish plaster, to Imperial gypsum base that has faded from exposure to sunlight. Where fading has occurred, treat surface with either USG plaster bonder or a spray-applied solution of USG accelerator-alum catalyst before application of finish. 4. Gypsum base surfaces should be isolated with control joints or other means where: (a) Partition or furring abuts a structural element (except floor) or dissimilar wall or ceiling; (b) Ceiling abuts a structural element, dissimilar wall or partition, or other vertical penetration; (c) Construction changes within the plane of the partition or ceiling; (d) Partitions or furring run exceeds 30'; (e) Ceiling dimensions exceed 30' without relief, or 50' with relief; (f) Expansion or control joints occur in the base exterior wall. Ceiling-height door frames may be used as control joints, as may door frames that are less than ceiling height, if control joints extend to ceiling from both corners. 5. Do not exceed the maximum spacing of framing members shown in the table below. Maximum spacing of framing members for new construction: base and finish assembly framing spacing (1) in. mm in. mm 1/2 12.7 Imperial gypsum base one layer, 1-coat system 16 406.4 one layer, 2-coat system 16 or 24 (2) 406.4 or 609.6 (2) two layer, 1 & 2-coat system 24 609.6 5/8 15.9 Imperial gypsum base one layer, 1-coat system 16 or 24 (2) 406.4 or 609.6 (2) one layer, 2-coat system 24 (2) 609.6 (2) two layer, 1 & 2-coat system 24 609.6 (1) For perpendicular or parallel application to framing. Perpendicular is preferred for maximum strength; parallel application is not recommended for ceilings. (2) 24" (609.6 mm) spacing requires joint treatment with Sheetrock joint tape and Sheetrock setting-type joint compound (Durabond or Easy Sand ).
Directions Preparation Protect the product from moisture during storage and on the job. In cold weather, heat the interior of the building to a minimum of 55 F (13 C) for an adequate period before the application of plaster, while basecoat and finish is being applied, and until the finish is dry. Air circulation should be kept at a minimum level during this period. Warning: Store all Imperial gypsum base flat. Panels are heavy and can fall over, causing serious injury or death. Do not move unless authorized. Under normal working conditions, joints of veneer plaster systems may be treated by applying Imperial tape Type P (pressure-sensitive) or Type S (staple) to the joints and then applying the veneer plaster basecoat or finish to preset the tape. However, there are a number of special situations that require the use of a setting-type joint treatment system. High building temperature, low humidity or excessive evaporation that creates rapid drying conditions. Metal framing is specified. Certain wood-framing applications with spacing of 24" o.c. (see Maximum Spacing table above). Under any of these conditions, use Sheetrock joint tape and Sheetrock setting-type (Durabond) or lightweight settingtype (Easy Sand) joint compound to treat all joints and internal angles. Allow the joint treatment to set and dry thoroughly before plaster application. Mist with water prior to initial plaster application. Installation Imperial gypsum base may be installed either perpendicular (preferred) or parallel to the framing. All ends and edges should be placed over framing members except where edge joints are perpendicular to framing. Use maximum practical lengths to minimize end joints. Install gypsum base first on ceilings and then on walls. Over steel studs, arrange direction of installation so that the lead edge of the base is attached to the open side of the stud flange first. Bring base panels into contact with each other, but do not force into place. Fit abutting ends and edges neatly; stagger end joints; arrange joints on opposite sides of partition so they occur on different studs. Begin driving fasteners in center of panel and work toward ends and edges, holding gypsum base in firm contact with framing. Space fasteners as shown in table and not less than 3/8" from edges and ends of panel. Drive fastener heads flush with surface without breaking the face paper. If gypsum base appears to be loose from framing, install additional fasteners. Float vertical and horizontal interior corners by placing fasteners 8" out from the corner. Where framing is parallel with the corner, attach one panel to corner framing and float the abutting panel. Cut and fit gypsum base neatly around pipes and other openings. Remove loose face paper around cuts and use quick-setting plaster to close openings. Control Joints Apply control joints, where required, over the face of the gypsum base. Cut to required lengths with finetoothed hack saw. Cut end joints square, align and butt together slightly gapped. Attach the control joint to gypsum base temporarily with 9/16" rosin-coated staples spaced 12" o.c. along each flange. Complete the installation of the control joint with fasteners (nails or screws) driven through the control joint flange into the framing on each side of the joint. The protective plastic tape over the open groove should be left in place until finishing is completed. Metal Trim Fasten gypsum base in normal manner but omit fasteners at framing member where metal trim is to be installed. Leave a space 3/8" to 1/2" wide between edge of base and face of jamb or wall. This provides space for hardware or door bucks and allows for expansion when trim is used for perimeter isolation. Slip trim over edge of base with expanded mesh flange on face side. Fasten to base by nailing or stapling 12" o.c. Vinyl Trim Slip vinyl trim over gypsum base with long flange behind base. Install the base with the trim firmly abutting the surface. Corner Bead Apply to all external angles. Hold tightly against angle and fasten to base by nailing or stapling 12" o.c. alternately on both flanges along entire length. Acoustical Sealant Seal edges of gypsum base around entire perimeter of partition. Also, seal air-tight all penetrations of the gypsum base, particularly electrical boxes. In addition to sealing the perimeter of electrical boxes, coat the back sides with a layer of acoustical sealant. Apply acoustical sealant under control joints and similar openings between the gypsum base and abutting materials.
Product Data Materials: Panels with gypsum core, paper encased, square or tapered edges. Compliance with Standards: Imperial gypsum base meets ASTM Designation ASTM C1396/1396M. Thermal coefficient of expansion (unrestrained): 9.2x10 6 in./in. x F (40-100 F); 16.2 mm/km x C (4-38 C). Hygrometric coefficient of expansion (unrestrained): 7.2x10 6 in./in. x F (7.2 mm/km x C) at 5-90% R.H. Storage: Store material in a cool, dry place. Avoid direct sunlight. Maintain temperature above 40 F (4 C). Availability and Cost: Imperial gypsum base is distributed throughout the United States. Contact a United States Gypsum Company sales office or sales person for additional information. Types, sizes, packaging and weights: Approximate weight Thickness Width Length Pc./ lb./ kg/ Product in. mm in. mm ft. mm bdl. 1000ft. 2 100m 2 Imperial Base Firecode 5/8 15.9 48 1219.2 8 2438.4 2 2330 1140 Firecode C 5/8 15.9 48 1219.2 14 4267.2 2 2480 1210 Submittal Approvals: Job Name Contractor Date Trademarks The following trademarks used herein are owned by United States Gypsum Company: Diamond, Durabond, Durock, Easy Sand, Firecode, Imperial, Mold Tough, Sheetrock, USG, USG in stylized letters. Note Products described here may not be available in all geographic markets. Consult your United States Gypsum Company sales office or representative for information. Notice We shall not be liable for incidental and consequential damages, directly or indirectly sustained, nor for any loss caused by application of these goods not in accordance with current printed instructions or for other than the intended use. Our liability is expressly limited to replacement of defective goods. Any claim shall be deemed waived unless made in writing to us within thirty (30) days from date it was or reasonably should have been discovered. Safety First! Follow good safety and industrial hygiene practices during handling and installing products and systems. Take necessary precautions and wear the appropriate personal protective equipment as needed. Read material safety data sheets and related literature on products before specification and/or installation. Manufactured by United States Gypsum Company 550 West Adams Street Chicago, IL 60661 800 USG.4YOU (874-4968) usg.com P790/rev. 4-11 2011, United States Gypsum Company Printed in U.S.A.
Technical Service Hotline 1.800.225.6119 or www.gpgypsum.com Manufacturer Georgia-Pacific Gypsum LLC Georgia-Pacific Canada LP 133 Peachtree Street 7070 Mississauga Road, Unit 120 Atlanta, GA 30303 Mississauga, ON L5M 7V9 Technical Service Hotline: 1-800-225-6119 Description ToughRock Veneer Plaster Base for veneer plaster has a noncombustible (per ASTM E 136), dimensionally stable, inert gypsum core. The front face and long edges are a blue colored, highly absorbent, special paper. The surfacings on both faces and the long edges are 100% recycled paper. The back paper is gray. The special face paper is designed for the application of gypsum veneer plasters meeting ASTM C 587. The ends are square cut, smooth finished with no paper facing. Tradesmen often refer to ToughRock Veneer Plaster Base as Blue Board because of the facing color. Production Specification ToughRock Veneer Plaster Base is manufactured to meet the requirements of ASTM C 1396 Section 10; CSA-A82.27-M; and Federal Specification SS-L-30D, Type VI, Grade R or X, Class 1, Form A, Style 3. The product conforms to the requirements of major building codes for its intended use. Limitations ToughRock Veneer Plaster Base is a non-structural product and must not be used as a nailing base to support heavy wall-mounted objects. It is intended for interior applications only. It must be kept dry and cannot be used where exposure to moisture is extreme or continuous. Do not use ToughRock Veneer Plaster Base where there is prolonged exposure to temperatures exceeding 125 F (52 C) and/or continuous exposure to extreme humidity; e.g., adjacent to wood burning stoves, heating appliances, steam rooms, showers, gang shower rooms and swimming pools. Installation ToughRock Veneer Plaster Base shall be installed according to the Gypsum Association Publication GA-216 Recommended Specifications for the Application and Finishing of Gypsum Board and ASTM C 840 Standard Specification for Application and Finishing of Gypsum Board for non-fire rated construction. However, to achieve a designated fire resistance rating, installation and details must be consistent with tested assemblies as listed in the Gypsum Association Fire Resistance Design Manual GA-600 and UL/ULC Fire Resistance Directory. Supplemental Materials Fasteners: Nails, screws or adhesive Joint System: Tape, bedding compound Veneer Plaster Technical Data Flame spread 15 and smoke developed 0 when tested in accordance with ASTM E 84 or CAN/ULC-S102. The core is non-combustible when tested in accordance with ASTM E 136. 5/8 (15.9 mm) ToughRock Fireguard Veneer Plaster Base is UL classified, Type 9 in the following UL assemblies: Design Nos. G501, G520, G531, L501, L508, L532, L556, L591, N501, N502, N505, N602, P225, P227, P230, P235, P254, P259, P266, P302, P516, P517, P701, P710, P711, P713, P714, P717, P718, P719, P720, P722, P725, P728, P729, P730, P731, P732, P733, P734, P735, P738, P739, P740, P741, P742, P801, P811, P815, P819, P824, P825, P826, P827, P828, S728, S736, U017, U032, U040, U204, U207, U301, U302, U305, U309, U326, U329, U330, U332, U337, U338, U339, U341, U342, U351, U354, U356, U357, U358, U360, U364, U369, U379, U396, U411, U418, U420, U421, U425, U434, U436, U439, U442, U449, U450, U460, U465, U467, U473, U475, U487, U494, U495, U502, U504, U505, U506, U510, U512, U513, U531, U617, U623, U626, U633, U646, U647, U648, U651, U652, U926, V417, V419, V420, V421, V430, V432, V434, V450, V435, V473, V486, V487, X508, X516, X517, X525, X526, X527, X528, X602, and X604. Application Standard For all non-rated assemblies, install ToughRock Veneer Plaster Base at right angles or parallel to framing using nails, screws or a combination of nails or screws with adhesive in accordance with ASTM C 844, Application of Gypsum Base to Receive Gypsum Veneer Plaster. Reinforce joints with mesh tape and gypsum veneer plaster applied in accordance with ASTM C 843, Application of Gypsum Veneer Plaster. Please refer to Recommended Procedure for the Application and Finishing of Gypsum Panel Products (GA-216), published by the Gypsum Association, and Standard Specification for Application and Finishing of Gypsum Board, ASTM C 840 for application procedures. Sound-rated assemblies require sealing at top, bottom, intersections and penetrations to ensure the effectiveness of the assembly and to obtain the desired STC rating. Test reports are available upon request. ToughRock Veneer Plaster Base can be cut to the necessary size by scoring the face paper with a sharp knife then snapping away the cut face. Then cut or break the back paper by snapping the board in the opposite direction. Smooth all cut edges and ends by rasping or other suitable methods to form tight-fitting joints when installed. Safety Precautions See Handling and Use Caution section at the end of this document. Handling Precautions Stack ToughRock Veneer Plaster Base flat on a level surface. As individual sheets are removed for installation, they should be raised up on edge carefully and carried in a vertical position. (Appropriate handling is outlined in Gypsum Association publications GA-216 and GA-801.) Avoid impact, undue flexing and damage to board edges, ends and corners. Avoid scuffing the face to be finished. A Material Safety Data Sheet (MSDS) is available upon request. Material Safety Data Sheet Material Safety Data Sheet (MSDS) is available upon request or online at www.gpgypsum.com. Submittal Approvals Job Name Contractor continued Date Stamps/Signatures
Technical Service Hotline 1.800.225.6119 or www.gpgypsum.com Physical Properties Properties 1 Toughrock Veneer Plaster Base Toughrock FireGuard Veneer Plaster Base Thickness, nominal 1/2 (12.7 mm) 5/8 (15.9 mm), ± 1/64 (0.4 mm) Width, nominal 4 (1220 mm) 4 (1220 mm) Length, Standard 8 (2440 mm) to 8 (2440 mm) to 12 (3660 mm) ± 1/4 (6.4 mm) 12 (3660 mm) ± 1/4 (6.4 mm) Weight, lbs./sq. ft., nominal (kg/m 2 ) 1.7 (7.8) 2.1 (9.5) Edges Tapered Tapered Flexural strength, minimum Parallel, lbs. >_ 40 (178) >_ 50 (222) Perpendicular, lbs. >_ 110 (498 >_ 150 (666) R Value 2 F ft 2 hr/btu (K m 2 /W).45 (0.08).56 (0.10) Nail Pull Resistance, Minimum, lbs. (N) >_ 80 (356) >_ 90 (400) Hardness, lbs. force (core, edge and end) (N) >_ 15 (67) >_ 15 (67) Humidified Deflection, maximum 10/8 (32 mm) 5/8 (15.9 mm) Packaging Two pieces per bundle, Two pieces per bundle, face-to-face and end taped face-to-face and end taped Surface Burning Characteristics Flame Spread 15 Flame Spread 15 (per ASTM E84 or CAN/ULC-S102) Smoke Developed 0 Smoke Developed 0 1 Tested in accordance with ASTM C 473. 2 Tested in accordance with ASTM C 518, Heat Flow Meter NOTE: Specified minimum values are as defined in ASTM C 588 and ASTM C 1396. Other sizes may be available on special order. U.S.A. Georgia-Pacific Gypsum LLC Canada Georgia-Pacific Canada LP SALES INFORMATION AND ORDER PLACEMENT U.S.A. Midwest: 1-800-876-4746 West: 1-800-824-7503 South: 1-800-327-2344 Northeast: 1-800-947-4497 CANADA Canada Toll Free: 1-800-387-6823 Quebec Toll Free: 1-800-361-0486 TECHNICAL INFORMATION U.S.A. and Canada: 1-800-225-6119 www.gpgypsum.com 2010 Georgia-Pacific Gypsum LLC. All rights reserved. Printed in the U.S.A. 10/10 GP-TM Lit. Item #101519. TRADEMARKS Unless otherwise noted, all trademarks are owned by or licensed to Georgia-Pacific Gypsum LLC. WARRANTIES, REMEDIES AND TERMS OF SALE For current warranty information for this product, please go to www.gpgypsum.com and select the product for warranty information. All sales of this product by Georgia-Pacific are subject to our Terms of Sale available at www.gpgypsum.com. UPDATES AND CURRENT INFORMATION The information in this document may change without notice. Visit our website at www.gpgypsum.com for updates and current information. CAUTION For product fire, safety and use information, go to www.gp.com/safetyinfo or call 1-800-225-6119. HANDLING AND USE CAUTION This product may contain fiberglass which may cause skin irritation. Dust and fibers produced during the handling and installation of the product may cause skin, eye and respiratory tract irritation. Avoid breathing dust and minimize contact with skin and eyes. Wear long sleeve shirts, long pants and eye protection. Always maintain adequate ventilation. Use a dust mask or NIOSH/MSHA approved respirator as appropriate in dusty or poorly ventilated areas. FIRE SAFETY CAUTION Passing a fire test in a controlled laboratory setting and/or certifying or labeling a product as having a one-hour, two-hour, or any other fire resistance or protection rating and, therefore, as acceptable for use in certain fire rated assemblies/systems, does not mean that either a particular assembly/system incorporating the product, or any given piece of the product itself, will necessarily provide one-hour fire resistance, two-hour fire resistance, or any other specified fire resistance or protection in an actual fire. In the event of an actual fire, you should immediately take any and all actions necessary for your safety and the safety of others without regard for any fire rating of any product or assembly/system.