XL0897 HIGH-FLASH POE CHAIN OIL

XL0897 XL0897 HIGH-FLASH POE CHAIN OIL XL0897 is a polyolester-based lubricant formulated with highly stable polymers to increase its viscosity index. This helps prevent the formation of varnish and carbon deposits at high temperatures, and in most applications, dislodge existing sludge and varnish deposits formed from previous lubricant applications. The inherent high viscosity index of XL-0897 permits optimal lubrication across a wide range of temperatures. XL0897 series of synthetic chain lubes are designed for the lubrication of chains, slide-ways and gears where temperatures may exceed 150 C. These fluids are anti-static, and will not leave any residue once the carrier evaporates. XL0897 does not leave any carrier residue, and was formulated specifically to give maximum protection against wear, rust, oxidation and corrosion, thereby prolonging equipment life, while reducing overall maintenance costs. XL0897 reduces energy consumption by maintaining a clean lubricating film, even at high temperatures, which extends the interval between re-lubrication and reduces the amount of oil consumed. This also reduces the smoke and odours inherent to hot oil. ADVANTAGES: XL0897 is recommended for: Exceptional stability at high temperatures High temperature conveyor chains Cleanliness Chains for bottling plants Smokeless Chains in ceramic plants Low Volatility Bearings for drying ovens Energy Efficiency Improved Protection High Viscosity Index TYPICAL SPECIFICATIONS Product Code: XL0897 /068 /100 /220 /460 ISO Grade 68 100 220 460 Viscosity (cst @ 40 C) (ASTM D-445) 68 100 220 460 Viscosity (cst @ 100 C) (ASTM D-445) 10 12 19 26 Viscosity Index 130 105 95 70

TYPICAL SPECIFICATIONS Flash Point ( C) 310 310 305 300 Fire Point ( C) 330 330 340 320 Pour Point ( C) -45-45 -20-15 Residue 20 hrs @ 260 C (%weight) 17 14 27 19 Shell 4 Ball Wear Test 40kg (ASTM D-4172) 0.39 0.43 0.38 0.89 Specific Gravity (g/ml @ 25 C) 0.99 0.98 0.98 0.96 RBOT 150 C (min) (ASTM D-2272) 900 1100 1100 1980 XL2355 XL2355 FAST-DRYING FILM LUBRICANT WITH MOLYBDENUM XL2355 offers excellent extreme pressure dry film lubrication. This specially processed long wearing molybdenum disulfide coating air dries at room temperatures in approximately ten minutes, and offers superior performance at high temperatures and heavy loads. ADVANTAGES: Low coefficient of friction Excellent adhesion to most substrates, especially metals. Thin film 0.003 to 0.005 in. (0.008 to 0.013 millimetres). Excellent release properties. Minimum surface pre-treatment. Easy application. Fast room temperature cure. XL2355 can be applied to all substances not affected by the fluid component. Compatibility with

seals, gaskets, and plastics should be assessed on a case-by-case basis. PHYSICAL PROPERTIES XL2355 (as supplied) Lubricant: Fluid Component: Molybdenum Disulfide Trichloroethylene Dark Grey XL-2355 (when cured) Coefficient of Friction: 0.23 (static) Service Temperature ( C / F): 315 C / 600 F Intermittent Temperature ( C) 350 C / 660 F XL7360 XL7360 GENERAL PURPOSE SYNTHETIC TACKY LUBE XL7360 is a unique general-purpose oil containing P.T.F.E. resin (Teflon ) in sub-micron colloidal suspension, recognized for its exceptional sliding properties and friction reduction. XL7360 contains special long-chain polymer additives that will adhere to most metal surfaces and prevent dripping. XL7360 is known for its exceptional sliding properties, and its reduction of friction between moving parts. XL7360 is recommended as a general-purpose oil for chains, cams, slide-ways, air lines, pneumatic tools, open gears, and other applications. XL7360 has been approved by the Canadian Department of Agriculture for use in federally inspected food processing plants. XL7360 is available in all viscosity grades.

The XL7360/800 Series is specially formulated to provide the same properties and specifications as the base series, but with the added lubricity of molybdenum. TYPICAL SPECIFICATIONS Product Code: XL7360/000 (PTFE) /010 /022 /032 /046 /068 /100 /220 /320 /460 Product Code: XL-7360/800 (PTFE + moly) /801 /822 /832 /846 /868 /810 /820 /830 /840 SAE Grade - 5W - - - - - - - ISO Grade 10 22 32 46 68 100 220 320 460 Viscosity (cst @ 40 C) (ASTM D-445) 9.5 21.4 31 44.7 71.1 108 210 315 432 Viscosity (cst @ 100 C) (ASTM D-445) - 4.8 6.1 7.8 11.4 15.5 24.5 32.6 42.7 Viscosity Index - 152 148 145 154 152 146 145 152 Pour Point ( C) (ASTM D-97) -63-58 -47-40 -40-35 -31-28 -22 Colour Green or Natural (Dark grey / Black with Moly) XL6331 XL6331 PENETRATING OIL XL6331 is a uniquely formulated penetrating oil designed to displace water, remove rust and lubricate metal surfaces. XL6331, once applied, will leave a fine long chain polymer film to protect metal surfaces from rust. TYPICAL CHARACTERISTICS: Contains no solids. Will soften residual lubricant deposits. An efficient EP lubricant. Reduces energy consumption by reducing friction on moving parts. Water displacing formulation. Excellent salt water resistance. Compatible with mineral oils and most synthetic base stocks. High chemical stability. Excellent low temperature properties.

High dielectric strength. Application: XL6331 can be applied by spray, brush or dip method. TYPICAL SPECIFICATIONS Product Code: XL6331 /200 /201 Flash Point with solvent ( C) 61 61 Flash Point without solvent ( C) 200 200 Specific Gravity (g/ml) 0.89 0.89 Pour Point ( C) -60-60 Volatility (%) >45 >45 Boiling Point ( C) 180 180 ph 6-7 6-7 Dielectric force (ASTM D-877) >25kV >25kV XL6330 XL6330 WATER-DISPLACING PENETRATING OIL XL6330 is a uniquely formulated penetrating oil designed to displace water, remove rust and lubricate metal surfaces. Once applied, XL6330/005 will leave a fine long-chain polymer film that will protect metal surfaces from rust, and prevent new rust from forming. XL6330/005 Can be applied by spray, brush or dip methods. Typical characteristics: Contains no solids Excellent cleaning properties Will soften residual lubricant deposits An efficient EP lubricant

Reduces energy consumption by reducing friction on moving parts Water displacing formulation Excellent salt water resistance Compatible with mineral oils and most synthetic base stocks High chemical stability Excellent low temperature properties High dielectric strength TYPICAL SPECIFICATIONS Product Code: XL6330 /005 Flash Point with solvent ( C) 61 Flash Point without solvent ( C) 200 Specific Gravity (g/ml) 0.89 Pour Point ( C) -60 Volatility (%) > 45 Boiling Point ( C) 180 ph 6-7 Dielectric force (kv) (ASTM D-877) > 25 XL2362 XL2362 WATER-BASED PAG DRY FILM CHAIN LUBRICANT WITH MOLYBDENUM FOR HIGH TEMPERATURES XL2362 has been carefully formulated to function as a high temperature lubricant suitable for use on chains, wire drawing, metal forging, and mold release applications where a tenacious lubricant film is required. The pure molybdenum suspended in water dries and forms a film that will adhere to virtually any surface. XL2362 remains stable a service temperature up to 316 C or 600 F.

XL2362 is: Environmentally friendly Non flammable Non oxidizing PHYSICAL PROPERTIES XL2362 (as supplied) Lubricant: Fluid Component: Diluents: Consistency: Sub-micron molybdenum PAG, Water Water Dark Grey Liquid XL-2362 (when cured) Coefficient of Friction: 0.23 static Film thickness (mm): 0.008 0.013 SURFACE PREPARATION: Surface should be thoroughly cleaned and dried prior to application of XL2362 in order to insure the greatest film stability. Pressure washing or sand-blasting of surface prior to application is highly recommended. METHOD OF APPLICATION: XL2362 can be applied with a brush or sprayed directly to metal surface. For oven chains and rollers, XL2362 should be sprayed onto warm surfaces at temperatures greater than 100 C/212 F and spray pressures between 80-100 PSI so that the water component will evaporate on contact, and provide a fine film of molybdenum and PAG. MIX WELL BEFORE USING KEEP CONTAINERS WELL SEALED STORE AT ROOM TEMPERATURE KEEP FROM FREEZING XL2361

XL2361 WATER-BASED PAG DRY FILM CHAIN LUBRICANT WITH GRAPHITE FOR HIGH TEMPERATURES XL2361 is a high temperature chain lubricant formulated from a pure graphite base suspended in a synthetic lubricant and water carrier that dries quickly to form an adherent film on virtually all surfaces, including glass and flexible materials. XL2361 remains stable at service temperatures of 316 C (600 F) and at intermittent temperatures of 1200 C (2200 F). XL2361 is approved by the Canadian Food inspection Agency (CFIA) for use in food processing plants. Advantages: Environmentally safe Non-flammable Non-corrosive Non-toxic SURFACE PREPARATION: Substrate must be clean and dry. Etching or sandblasting will improve adhesion and wear properties. DILUTION: XL2361 must be diluted with soft, distilled, or demineralized water to bring the product to the desired consistency prior to use, if necessary. This is achieved by adding water to XL2361, and NOT vice-versa. Addition of water must be done while solution is being thoroughly agitated. APPLICATION: May be applied by using spray, brush, or dip methods. For oven chains and rollers, XL2361 should be sprayed onto warm surfaces at temperatures greater than 100 C/212 F and spray pressures between 80-100 PSI so that the water component will evaporate on contact, and provide optimum film formation. XL2361 (as supplied) PHYSICAL PROPERTIES Lubricant: Fluid Component: Diluents: Micro-graphite Water, Synthetic Lubricant Water Dark Grey XL-2361 (when cured) Dark Grey Coefficient of Friction: 0.22 static Recommended thickness (mm) 0.003 0.008 MIX WELL BEFORE USING STORE AT ROOM TEMPERATURE

KEEP CONTAINER WELL-SEALED KEEP FROM FREEZING XL2360 XL2360 WATER-BASED GRAPHITE COATING XL2360 is a colloidal dispersion of extremely fine pure graphite in a water-based carrier that dries to form an electrically conductive adherent film on virtually all surfaces, including glass and flexible materials. XL2360 remains stable at service temperatures of 316 C/600 F and at intermittent temperatures of 1200 C/2200 F. Advantages: Environmentally safe Non-flammable Non-corrosive Non-toxic SURFACE PREPARATION: Substrate must be clean and dry. Etching or sandblasting will improve adhesion and wear properties. DILUTION: XL2360 must be diluted with soft, distilled, or demineralized water to bring the product to the desired consistency prior to use. This is achieved by adding water to XL2360, and NOT vice-versa. Addition of water must be done while solution is being thoroughly agitated. APPLICATION: May be applied by using spray, brush, or dip methods. Dries in 20 minutes. If surface temperatures are over 100 C the water portion of XL2360 will evaporate quickly leaving a fine film of graphite.

PHYSICAL PROPERTIES XL2360 (as supplied) Lubricant: Fluid Component: Diluents: Micro-graphite Water Water Dark Grey XL-2360 (when cured) Coefficient of Friction: 0.22 static Film thickness (mm): 0.003 0.008 MIX WELL BEFORE USING STORE AT ROOM TEMPERATURE KEEP FROM FREEZING XL2359 XL2359 WATER-BASED DRY FILM WITH MOLYBDENUM FOR HIGH TEMPERATURES XL2359 has been carefully formulated to function as a high-temperature lubricant suitable for use on metal forging and mold release applications where a tenacious lubricant film is needed. XL2359 is a colloidal dispersion of extremely fine sub-micron molybdenum in a water-based carrier that dries to form an electrically conductive adherent film on virtually all surfaces, including glass and flexible materials. XL2359 remains stable at service temperatures of 316 C/600 F and at intermittent temperatures of 1200 C/2200 F Advantages: Environmentally friendly Non-flammable

Non-oxidizing Non-toxic (when dry) Dilution: XL2359 must be diluted with soft, distilled, or demineralized water to bring the product to the desired consistency. The water must be added to the XL2359, and NOT THE REVERSE. Add water to solution while mixing. Method of application: XL2359 should be applied by brush or sprayer directly on to the metal surface. XL2359 dries in approximately 20 minutes. If surface temperatures are over 100 C the water portion of XL2359 will evaporate quickly leaving a fine film of molybdenum. PHYSICAL PROPERTIES XL2359 (as supplied) Lubricant: Fluid Component: Diluents: Sub-micron molybdenum Water Water Dark Grey XL-2359 (when cured) Coefficient of Friction: 0.23 static Film thickness (mm): 0.008 0.013 MIX WELL BEFORE USING STORE AT ROOM TEMPERATURE KEEP FROM FREEZING XL2356 XL2356 DRY FILM WITH GRAPHITE XL2356 is a solvent-dispersed colloidal graphite that air dries to the touch in 10 minutes, and

completely cures in 30 minutes. XL2356 penetrates and adheres tenaciously to most metallic substrates with minimal surface pretreatment and preparation. Although this procedure is adequate with most applications, to achieve maximum corrosion and rust resistance, surfaces should be thoroughly cleaned and sandblasted prior to application. Once dry, XL2356 forms an exceptionally stable, rust/corrosion resistant, and tough micro-graphite coating highly resistive to temperature fluctuations from -60 C to 400 C. Because of its excellent adhesion to metallic surfaces and dry film consistency, XL2356 reduces potential environmental problems caused by conventional lubricating greases due to water wash-off from rain and snow, and product melting from exposure to the sun. XL2356 offers: Thin opaque film High lubricity Lubrication at temperature extremes Excellent adhesion Good electrical conductivity Excellent rust and corrosion resistance Room-temperature curing Prevents galling, fretting & seizing Long lasting Will not plug application equipment DILUTION: XL2356 is thixotropic in nature and will gel during storage. Preparation involves mild agitation and dilution (if required) to the consistency required for the application method chosen. APPLICATION: Can be applied by spray, brush, dip, or roller methods. Always agitate thoroughly prior to use. CURING: Coating air dries to touch in ten minutes under normal ambient conditions. Full cure properties develop in approximately thirty minutes depending on the film thickness. PHYSICAL PROPERTIES XL2356 (as supplied) Lubricant: Binder: Fluid Component: Diluents: Flash Point: Colloidal graphite Thermoplastic resin Mineral spirits, Isopropyl alcoho Mineral spirits Black 40.5 C

PHYSICAL PROPERTIES XL-2356 (when cured) Coefficient of Friction: 0.167 static Service Temperature ( C): -60 to 400 Intermittent Temperature ( C): -80 to 550 FLAMMABLE LIQUID SHAKE WELL BEFORE USE