MATERIAL NUMBERS. Material Number Extended Description 1a. 6 mm or 8 mm thick Rockpanel panels 1b

Transcription

1 technical design guide quality in front

2 page 1 MATERIAL NUMBERS relating to the APPLICATION DETAILS Material Number Extended Description 6 mm or 8 mm thick Rockpanel panels 1b Rockpanel Lines T&G 10 mm thick EPDM self adhesive gasket, 60 mm thick REF 090/9N 3 Battens 4 Membrane, vapour open, watertight and non capillary Wooden construction 6 Rockwool insulation batts 8 Brickwork For insulated and non ventilated constructions without vapour barrier, the sum of the sd-values from the cold side of the insulation, up to and including the internal finish, should be at least 10 m (1-30, 1-37). For non insulated and non ventilated constructions with 6 mm or 8 mm panels, without vapour barrier, the sum of the sd-values from the back of the board up to and including the internal finish, should be at least 4 m (1-710). For non insulated and non ventilated constructions with Rockpanel Lines without vapour barrier, the sum of the sd-values from the back of the board up to and including the internal finish, should be at least. m (1-718). 9 Flashing, reference AL/FLASH/ measurement required 18 Ventilation Profile 18a Soffit strip 0/10K 18b Bottom venting strip - ref: 06/10K to fit cavity 30 mm to 6 mm - ref: 010/K to fit cavity 6 mm to 110 mm - ref: 03/10K to fit cavity mm to 30 mm - ref: 0/10K to fit cavity 1 mm to mm 19a Self adhesive PU-TPE tape, ref 0 range 8 8a plasterboard 8b plywood 30 Vapour barrier: 30a For 6 mm or 8 mm panels insulated applications: sd at least 10 m (1-711, 1-713) For Rockpanel Lines insulated applications: sd at least 13 m (1-719) The sd value from PE-foil 0.1mm is for instance 9.8 m 30b Alternative position for applications when refurbishing existing walls/constructions. Note: - pi not more than 1330 Pa - layers from cold side of the insulation up to and including 6 mm or 8 mm panels not more than: - for 6 mm or 8 mm panels: 3.3 m - for Rockpanel Lines: 4. m - inside of the construction should be airtight Remark: for the sd-value, the total sum of values from the cold side of the insulation, up to and including internal finish, can be taken. 3 Chair profile - anodised extruded Aluminium profile, overlap with top board at least 1 mm: Ref: AL/CH6 for 6 mm board or AL/CH8 for 8 mm board. - PVC profile, UV and weather resistant, overlap with top board at least 1 mm. Ref: 06P for 6 mm board or 08P for 8mm board. 33 UV & weather resistant sealant: Plastestick Ref: PL ST SEAL 34 Corner profile (Note: When using Aluminium profiles only AL/FT/EX1 can be used with Rockpanel Lines) - 34a: Anodised Aluminium External Profiles, AL/16P, AL/EX6, AL/FT/EX7 for 6 mm board. AL/18P, AL/ EX8, AL/FT/EX9 for 8 mm board and AL/FT/EX1 for 10 mm board. - 34b: Anodised Aluminium Internal Profiles, AL/EF6 for 6 mm board, AL/EF8 for 8 mm board and AL/EF10 for 10 mm board. - 34c: pvc external profile UV and weather resistant, 006P, 018P, 019/48P for 6 mm board, 008P, 010P, 019/48P for 8 mm board, 001P, 01P for 10 mm board. - 34d pvc internal profile UV and weather resistant 06P, PL/EF14 for 6 mm board, 08P, PL/EF38 for 8 mm board, 00P for 10 mm board. 37 Rainwater anchor - Plasticlad Ref: 830/041 for rainwater anchors 39 Starter trim AL/ST40

3 page Standard Fixing Dimensions for 6 mm and 8 mm thick rockpanel decorative panels TIMBER SUPPORT WORK for ventilated and non ventilated constructions 8 mm thick panel 6 mm thick panel 7 mm 0 mm 7 mm 7 mm 0 mm 0 mm 7 mm 60 mm joint gasket 60 mm joint gasket Typical detail for ventilated constructions featured here. 300 mm a a b 600 mm max 1 mm ar1 0 mm ar b 400 mm max 100 mm 100 mm 8 mm thick panel Timber support work sizing and spacing Support at board joints 7 mm min Intermediate supports 0 mm min Timber centres for screws and nails (b) 600 mm max Timber support work sizing and spacing Support at board joints 7 mm min Intermediate supports 0 mm min Timber centres for screws and nails (b) 400 mm max Maximum vertical fixing centres (a) for both edge and intermediate support for screws nails At intermediate supports 600 mm 400 mm At edges of boards 600 mm 400 mm From edges and corners of boards, horizontally (ar1) 1 mm 1 mm From edges and corners of boards, vertically (ar) 0mm 0 mm 6 mm thick panel Maximum vertical fixing centres (a) for both edge and intermediate support for screws nails At intermediate supports 400 mm 300 mm At edges of boards 400 mm 300 mm From edges and corners of boards, horizontally (ar1) 1 mm 1 mm From edges and corners boards, vertically (ar) 0 mm 0 mm In the event the building is in an area 100 m or more above sea level and/or in an area with windspeeds greater than 7 m/s (eg north west coast of Scotland), please contact Rockpanel. For non ventilated construction (sealed), alternative fixing centres may be required. The fixing centres above have been calculated for use up to 10 m high. Timber support work should be treated with a proprietary water based preservative conforming to the relevant British Standards. Applicable to ventilated and non-ventilated constructions.

4 page 3 details for the application of 6 mm and 8 mm thick rockpanel decorative panels Soffit and fascia detailing 1-08 For further specification guidance, see the Easy Spec Guides at the back of this brochure. Vertical Section Horizontal Section 37 18a Ensure adequate ventilation to the roof space is provided in accordance with BS 0: mm or 8 mm panels Gasket Wooden construction 18(a) Ventilation profile 37 Rainwater anchor Ref: NBS Clause G0/90

5 page 4 details for the application of 6 mm and 8 mm thick rockpanel decorative panels Timber frame NON VENTILATED CONSTRUCTION For further specification guidance, see the Easy Spec Guides at the back of this brochure. 8a b 4 6 mm or 8 mm panels Gasket 4 Breathable Membrane Wooden construction 6 Rockwool insulation batts 8a Plasterboard 8b Plywood 30 Vapour barrier 3 Chair profile Remark : see also extended description Ref: NBS Clause H0/10

6 page details for the application of 6 mm and 8 mm thick rockpanel decorative panels Ventilated construction 1-38 WINDOW HEAD AND SILL DETAIL For further specification guidance, see the Easy Spec Guides at the back of this brochure. 19a 7. mm 33 4 mm mm or 8 mm panels Gasket 3 Battens 4 Breathable membrane Wooden construction 6 Rockwool insulation batts 8 Brickwork 19a Foam tape 33 Sealant (MS Polymer) Ref: NBS Clause H9/10

7 page 6 details for the application of 6 mm or 8 mm thick rockpanel decorative panels non Ventilated construction 1-37 WINDOW HEAD AND SILL DETAIL For further specification guidance, see the Easy Spec Guides at the back of this brochure. 19a mm or 8 mm panels Gasket 4 Breathable membrane Wooden construction 6 Rockwool insulation batts 8 Brickwork 19a Foam tape 33 Sealant (MS Polymer) Remark: see also extended description! Ref: NBS Clause H0/10

8 page 7 details for the application of 6 mm or 8 mm thick rockpanel decorative panels NON VENTILATED CONSTRUCTION 1-30 window jamb detail For further specification guidance, see the Easy Spec Guides at the back of this brochure a 4 VENTILATED CONSTRUCTION window jamb detail a mm or 8 mm panels Gasket 3 Battens 4 Breathable membrane Wooden construction 6 Rockwool insulation batts 8 Brickwork 19a Foam tape 33 Sealant (MS Polymer) Remark: see also extended description! Ref: NBS Clause H0/10

9 page 8 details for the application of 6 mm or 8 mm thick rockpanel decorative panels non Ventilated construction method for new and refurbished applications For further specification guidance, see the Easy Spec Guides at the back of this brochure. 8a 30a b mm or 8 mm panels Gasket 4 Breathable Membrane Wooden construction 6 Rockwool insulation batts 8 Brickwork 8a Plasterboard 30 Vapour barrier (alternative positions 30a new/30b refurbished constructions) 3 Chair profile Remark : see also extended description Item 30b vapour barrier position for refurbishment applications where a foil-backed plasterboard 30a is not used Ref: NBS Clause H0/10

10 page 9 details for the application of 6 mm or 8 mm thick rockpanel decorative panels VENTILATED CONSTRUCTION fixing to timber battens 8 For further specification guidance, see the Easy Spec Guides at the back of this brochure mm or 8 mm panels Gasket UV - and weather resistant 3 Battens 8 Brickwork 3 Chair profile Remark : see also extended description Ref: NBS Clause H9/10 or Clause H0/10

11 page 10 details for the application of 6 mm or 8 mm thick rockpanel decorative panels VENTILATED insulated and ventilated construction For further specification guidance, see the Easy Spec Guides at the back of this brochure. 3 6 mm or 8 mm panels Gasket 3 Battens 4 Breathable Membrane Wooden construction 6 Rockwool insulation batts 8 Brickwork 3 Chair profile Remark : see also extended description 3 8 timber frame ventilated construction mm or 8 mm panels Gasket 3 Battens 4 Breathable Membrane Wooden construction 6 Rockwool insulation batts 8a Plywood 8b Plasterboard 30 Vapour barrier 3 Chair profile Remark : see also extended description 4 8a 6 8b

12 page 11 details for the application of 6 mm or 8 mm thick rockpanel decorative panels façade cladding 1-0 adjoining external brickwork For further specification guidance, see the Easy Spec Guides at the back of this brochure J mm or 8 mm panels Gasket 3 Battens Wooden construction 6 Rockwool insulation 8 Brickwork 9 Flashing 10 Ventilated opening 18 Ventilation profile J Open joint of mm or more

13 page 1 gasket fixing positions for both VENTILATED applications and non-ventilated applications For further specification guidance, see the Easy Spec Guides at the back of this brochure. 3a ar1 1 mm 1 mm mm 6 mm or 8 mm panels Gasket 3a Horizontal Chair Profile

14 page 13 DCS SYSTEM 01 OMEGA & ZED CARRIER RAILS Aluminium ProfilE alternative to timber (rivet or screw fixed) depth mm or 40 mm Set at mm or 40 mm depth For screw fixing, pre-drill board with 8 mm hole. Fix with screw (reference CSD 48 colour matched to board) according to manufacturer's instructions. Maximum board dimensions: 1. m vertically x 1. m horizontally. If screw fixing larger size panels, consult Rockpanel for guidance. For further information contact Rockpanel or Downer Cladding Systems on

15 page 14 ROCKTRACK DCS system 031 CARRIER RAIL SUPPORT SYSTEM VENTILATED CONSTRUCTION Aluminium ProfilE alternative on uneven surfaces rivet or screw fixed For cavity widths between 6 mm 400 mm For screw fixing, pre-drill board with 8 mm hole. Fix with screw (reference CSD 48 colour matched to board) according to manufacturer's instructions. Maximum board dimensions: 1. m vertically x 1. m horizontally. If screw fixing larger size panels, consult Rockpanel for guidance. For further information contact Rockpanel or Downer Cladding Systems on

16 page 1 rockpanel lines detailing VENTILATED CONSTRUCTION fixing to timber battens For further specification guidance, see the Easy Spec Guides at the back of this brochure b 34 18(b) 39 1b Rockpanel Lines Gasket 3 Battens 8 Brickwork 18(b) Ventilation profile 34 Corner profile 39 Starter trim Remark : see also extended description Ref: NBS Clause H9/10 or Clause H0/10

17 page 16 To help make it easier to provide specifications for your projects, we have created these Easy Spec Guides. There are five easy spec guides designed to suit the following applications: 1 SOFFIT AND FASCIA DETAILING using 6 mm or 8 mm decorative panels FAÇADE CLADDING APPLICATION VENTILATED Construction using 6 mm or 8 mm decorative panels 3 FAÇADE CLADDING APPLICATION NON VENTILATED construction using 6 mm or 8 mm decorative panels 4 ROCKPANEL LINES (Secret Fix) FAÇADE CLADDING ventilated construction Drawings and further Easy Spec Guides are available on our website: Rockwool Rockpanel BV Wern Tarw Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk

18 page 17 1 SOFFIT AND FASCIA DETAILING using rockpanel 6 mm and 8 mm decorative cladding boards Select your specifications using tick box options Sections showing no tick boxes are not optional Project name: SPECIFICATION GUIDANCE To complete the specification tick option boxes and fill in product description. ROCKPANEL decorative cladding boards STONEWOOL CLADDING BOARDS Dimensions 300 mm x 100 mm (some Rockpanel Rockclad boards available 00 mm long). Boards can be cut to size and shape on site. (I) BOARD TYPE Name board/description Rockpanel 8 mm thick board 6 mm thick board see (IV) fixing centres for board thickness option (II) BOARD COLOUR Reference (VI) SOFFIT BOARDS No gaskets required. (VII) BOARD JOINTS FASCIAS Leave a 3- mm gap at all board joints. SOFFITS Leave a 3- mm gap at all board joints. (VIII) JUNCTION of FASCIA and SOFFIT Fascia board should extend past soffit by min. 7. mm. Leave a gap of 4- mm between the junction of the soffit board and the fascia board. (IX) JUNCTION of SOFFIT and WALL Leave 4- mm gap between end of soffit board and external wall face. (X) FIXING CENTRES 8 mm thick Board TORX SCREW max. 600 mm timber centres 6 mm thick Board TORX SCREW max. 400 mm timber centres (III) TIMBER SUPPORT WORK VERTICALLY or HORIZONTALLY 8 mm thick board use timber support max. 600 mm centres 6 mm thick board use timber support max. 400 mm centres Minimum support at board joints 7 mm x 38 mm deep Minimum intermediate supports 0 mm x 38 mm deep (Above timbers can be planed down to 70 mm x 34 mm and 4 mm x 34 mm respectively) (IV) FASCIA BOARD JOINT TREATMENT EPDM SELF ADHESIVE JOINT FLEXIBLE GASKETS FIXED TO TIMBER SUPPORT WORK 8 mm Thick board S/S NAILS max. 400 mm timber centres 6 mm Thick board S/S NAILS max. 300 mm timber centres Fixings should be min. 1 mm from vertical edge of board and min. 0 mm from the horizontal edge of the board. (XI) FIXINGS Option 1: TORX SCREWS (colour matched heads Ref. RP8/SH 3 mm long) Option : STAINLESS RING SHANK NAILS AISI304 grade (colour matched heads Ref mm long) (XII) VENTILATION As required. FASCIA BOARD FLEXIBLE ADHESIVE FLEXIBLE JOINT GASKET AS DESCRIBED ABOVE At vertical board joints fix flexible joint gasket Ref. 090/9N At vertical corner joints fix flexible joint gasket Ref. 090/9N (V) DECORATIVE EXTERNAL CORNER PROFILE Optional detail when used there is no requirement to fit a flexible joint gasket as described in (iv) at the vertical corner joint under this corner profile. (XIII) PROFILES COLOUR MATCHED TO BOARD Black White ADDITIONAL COMMENTS / AMENDMENTS If alternative profiles are required see accessories brochure. Describe in box below. Option 1 Fix external box section corner profile (8 mm thick board) Fix external box section corner profile (6 mm thick board) Option Fix external capped corner profile (8 mm thick board) Fix eternal capped corner profil (6 mm thick board) Ref. 010P Ref. 018P Ref. 008P Ref: 006P Drawings and further Easy Spec Guides are available on our website: Rockwool Rockpanel B.V. Wern Tarw, Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk

19 FAçade cladding application ventilated construction using rockpanel decorative panels Select your specifications using tick box options Sections showing no tick boxes are not optional Project name: page 18 SPECIFICATION GUIDANCE To complete the specification tick option boxes and fill in product description. ROCKPANEL decorative cladding boards STONEWOOL CLADDING BOARD Dimensions 300 x 100 mm (some Rockpanel Rockclad boards available in 00 mm long). Boards can be cut to size and shape on site. (I) BOARD TYPE Name board/description Rockpanel 8 mm thick board 6 mm thick board see (IV) fixing centres for board thickness option (II) BOARD COLOUR Reference (III) vertical TIMBER SUPPORT WORK 8 mm thick board use timber support max. 600 mm centres 6 mm thick board use timber support max. 400 mm centres Support at board joints min. 7 mm wide x 38 mm deep Intermediate supports min. 0 mm wide x 38 mm deep (Above timbers can be planed down to 70 mm x 34 mm and 4 mm x 34 mm respectively) Option 1 CAVITY DEPTH To specify a cavity depth greater than 38 mm deep as above, enter depth of timber support work required mm (IV) VENTILATION PROFILES Optional detail Option 1: Fix bottom vent strip (to fit cavity from 30-6 mm) Ref. 06/10K Option : Fix bottom vent strip (to fit cavity from mm) Ref. 010/K (V) BOTTOM DRIPS Optional details Option 1: Fix bottom drip profile (8 mm thick board) Ref. 088P Option : Fix bottom drip profile (6 mm thick board) Ref. 086P (VI) VERTICAL JOINT TREATMENT EPDM SELF ADHESIVE FLEXIBLE JOINT GASKETS FIXED TO TIMBER SUPPORT WORK At vertical board joints fix flexible joint gasket Ref. 090/9N At vertical corner joints fix flexible joint gasket Ref. 090/9N Option Fix external capped corner profile (8 mm thick board) Ref. 008P Fix eternal capped corner profile (6 mm thick board) Ref: 006P (VIII) HORIZONTAL JOINT TREATMENT Option 1 Fix horizontal chair section (8 mm board) Ref. 08P Fix horizontal chair section (6 mm board) Ref. 06P Option Fix horizontal shadow gap (8 mm board) Ref. H/88J Fix horizontal shadow gap (6 mm board) Ref. H/66J (IX) FIXING CENTRES VERTICAL AND HORIZONTAL 8 mm thick Board TORX SCREW max. 600 mm centres 6 mm thick Board TORX SCREW max. 400 mm centres Fixings should be min. 1 mm from vertical edge of board and min. 0 mm from the horizontal edge of the board. (X) BOARD JOINTS Leave a 3- mm gap at all vertical board joints. (XI) FIXINGS TORX SCREW (colour matched heads Ref. RP8/SH 3 mm long) (XII) PROFILES COLOUR MATCHED TO BOARD Black White ADDITIONAL COMMENTS / AMENDMENTS If alternative profiles are required see accessories brochure. Describe in box below. (VII) DECORATIVE EXTERNAL CORNER PROFILES Optional detail When required fit gaskets as (vi) and select external corner profiles from below Option 1 Fix external box section corner profile (8 mm board) Ref. 010P Fix external box section corner profile (6 mm board) Ref. 018P Drawings and further Easy Spec Guides are available on our website: Rockwool Rockpanel B.V. Wern Tarw, Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk

20 page 19 3 FAçade cladding application non ventilated construction using rockpanel ROCKCLAD Select your specifications using tick box options Sections showing no tick boxes are not optional Project name: SPECIFICATION GUIDANCE To complete the specification tick option boxes and fill in product description. ROCKPANEL decorative cladding boards STONEWOOL CLADDING BOARD Dimensions 300 x 100 mm (some Rockpanel Rockclad boards available in 00 mm long). Boards can be cut to size and shape on site. (I) BOARD TYPE Name board/description Rockpanel 8 mm thick board 6 mm thick board see (IV) fixing centres for board thickness option (II) BOARD COLOUR Reference (III) vapour CHECKS Option 1 NEW BUILD Fit Vapour check to face of internal wall Option REFURBISHMENT Fit Vapour check to external wall face between timber support work and wall face For further information on vapour checks refer to Rockpanel. (IV) vertical TIMBER SUPPORT WORK 8 mm thick board use timber support max. 600 mm centres 6 mm thick board use timber support max. 400 mm centres Support at board joints min. 7 mm wide x 38 mm deep Intermediate supports min. 0 mm wide x 38 mm deep (Above timbers can be planed down to 70 mm x 34 mm and 4 mm x 34 mm respectively) Option 1 CAVITY DEPTH To specify a cavity depth greater than 38 mm deep as above, enter depth of timber support work required mm (V) INSULATION Fully fill cavity with ROCKWOOL RWA4 mm thick insulation, friction fitted between timber support work. (VI) BREATHABLE MEMBRANE Vapour open, water tight and non capillary fixed to manufacturers instructions, between the back of the Rockpanel board and the face of the insulation to the timber support work. (VII) VENTILATION PROFILES Optional detail Option 1: Fix bottom vent strip (to fit cavity from 30-6 mm) Ref. 06/10K Option : Fix bottom vent strip (to fit cavity from mm) Ref. 010/K Option 1 Fix external box section corner profile (8 mm board) Fix external box section corner profile (6 mm board) Option Fix external capped corner profile (8 mm thick board) Fix eternal capped corner profile (6 mm thick board) Ref. 010P Ref. 018P Ref. 008P Ref: 006P (XI) HORIZONTAL JOINT TREATMENT Option 1 Fix horizontal chair section (8 mm board) Ref. 08P Fix horizontal chair section (6 mm board) Ref. 06P Option Fix horizontal shadow gap (8 mm board) Ref. H/88J Fix horizontal shadow gap (6 mm board) Ref. H/66J Horizontal shadow gap to be fixed to board with Plastistick as shown in accessories brochure. (XII) FIXING CENTRES VERTICAL AND HORIZONTAL 8 mm thick Board TORX SCREW max. 600 mm centres 6 mm thick Board TORX SCREW max. 400 mm centres Fixings should be min. 1 mm from vertical edge of board and min. 0 mm from the horizontal edge of the board. (XIII) BOARD JOINTS Leave a 3- mm gap at all vertical board joints. (XIV) FIXINGS TORX SCREW (colour matched heads Ref. RP8/SH 3 mm long) (XV) PROFILES COLOUR MATCHED TO BOARD Black White ADDITIONAL COMMENTS / AMENDMENTS If alternative profiles are required see accessories brochure. Describe in box below. (VIII) BOTTOM DRIPS Optional detail Option 1: Fix bottom drip profile (8 mm thick board) Ref. 088P Option : Fix bottom drip profile (6 mm thick board) Ref. 086P (IX) VERTICAL JOINT TREATMENT FLEXIBLE JOINT GASKET FIXED TO TIMBER SUPPORT WORK, ON THE FACE OF THE BREATHABLE MEMBRANE At vertical board joints fix flexible joint gasket Ref. 090/9N At vertical corner joints fix flexible joint gasket Ref. 090/9N (X) DECORATIVE EXTERNAL CORNER PROFILES OPTIONAL DETAILS When required fit gaskets as (ix) and select external corner profiles from below Drawings and further Easy Spec Guides are available on our website: Rockwool Rockpanel B.V. Wern Tarw, Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk

21 4 Rockpanel lines (secret fix) façade cladding ventilated construction Select your specifications using tick box options Sections showing no tick boxes are not optional Project name: page 0 SPECIFICATION GUIDANCE To complete the specification tick option boxes and fill in product description. VENTILATED SYSTEM ROCKPANEL LINES STONEWOOL CLADDING BOARD Dimensions 300 x 97 mm x 10 mm (Working width 79 mm) Boards can be cut to size and shape on site. (I) BOARD TYPE ROCKPANEL LINES (VII) BOARD JOINTS Interlocking shiplap boards for Rockpanel Lines butt jointed horizontally. (IX) FIXING CENTRES Each shiplap piece nailed with SA4 Stainless steel nails. Ref mm max. 600 mm centres. The centre line of the nail fixing should be 11-1 mm from the top edge of the board. (II) BOARD COLOUR Reference (III) VERTICAL TIMBER SUPPORT WORK Use timber support max. 600 mm centres Support at board joints min. 7 mm wide x 38 mm deep Intermediate supports 0 mm min. wide x 38 mm deep (Above timbers can be planed down to 70 mm x 34 mm and 4 mm x 34 mm respectively) (X) PROFILES COLOUR MATCHED TO BOARD Black White ADDITIONAL COMMENTS / AMENDMENTS If alternative profiles are required see accessories brochure. Describe in box below. Option 1 CAVITY DEPTH To specify a cavity depth greater than 38 mm deep as above, enter depth of timber support work required mm (IV) VENTILATION PROFILES Optional detail Option 1: Fix bottom vent strip (to fit cavity from 30-6 mm) Ref. 06/10K Option : Fix bottom vent strip (to fit cavity from mm) Ref. 010/K (V) VERTICAL JOINT TREATMENT EPDM SELF ADHESIVE FLEXIBLE JOINT GASKETS FIXED TO TIMBER SUPPORT WORK At vertical board joints fix flexible joint gasket Ref. 090/9N At intermediate supports fix flexible joint gasket Ref. 090/9N At vertical corner joints fix flexible gasket Ref. 090/9N (VI) STARTER TRIM Fix Rockpanel Lines starter trim Ref. AL/ST40 (VII) DECORATIVE EXTERNAL CORNER PROFILE: OPTIONAL DETAIL WHEN REQUIRED FIT GASKETS AS (v) AND SELECT EXTERNAL CORNER PROFILES FROM BELOW Option 1 Fix external capped corner profile Option Fix Aluminium flat top external corner profile Ref. 001P Ref. AL/FT/EX/1 Drawings and further Easy Spec Guides are available on our website: Rockwool Rockpanel B.V. Wern Tarw, Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk

22 QUALITY IN FRONT Rockpanel, a member of the Rockwool International A/S group, with over EUR billion in sales worldwide and over 7,000 employees, develops top quality cladding material for facade exterior cladding and verge finishing. Rockpanel has multiple sales offices in Europe and stands for Design Freedom, Safety and Ease of Use. DESIGN FREEDOM SAFETY EASE of USE Rockpanel cladding is suitable for both new construction and renovation for many applications, such as facades and rooflines. Cladding is available in two types, each of which can be manufactured in various designs and in any desired RAL/NCS colour. In combination with the Rockpanel Accessories, Rockpanel provides the Total Solution for any design challenge. Rockpanel s cladding is manufactured from mineral wool fibres compressed under high pressure, and this manufacturing method gives its unique properties: dimensional stability, fireproof, as durable as stone, 100% recyclable and water proof. Rockpanel cladding is manufactured under the strict standards of ISO 9001 and ISO Rockpanel cladding can be worked and applied like wood, does not need pre-drilling, vapour open is lightweight, maintenancefriendly and needs no edge finishing. This means Rock panel saves you time and money. Rockwool Rockpanel B.V. does not accept responsibility for the consequences of using Rockpanel Boards in applications different from those discribed above. Expert advice should be sought where such different applications are contemplated, or where the extent of any listed applications is in doubt. The greatest possible care has been taken in the design and composition of this brochure. Nevertheless, we cannot guarantee the completeness and correctness of the information included herein. Price and product changes are reserved. Illustrations, colours, descriptions and information relating to dimensions, characteristics etc. apply only by approximation and are not binding. All of the information in this brochure is protected by copyright. This brochure, the texts, photos, other information included therein and/or parts thereof may not be reproduced, modified or published without the prior written approval of Rockpanel. TDUK11007 Rockwool Rockpanel B.V. Wern Tarw Pencoed Bridgend CF3 6NY Tel Fax info@rockpanel.co.uk