Mineral-Fibre Thermal Insulation for Buildings
|
|
- Liliana Lewis
- 6 years ago
- Views:
Transcription
1 Preface MASTERFORMAT REVISED DATE Mineral-Fibre Thermal Insulation for Buildings Scope These Evaluation Listings apply to mineral-fibre thermal insulation in the form of faced and unfaced batts, rolls, and boards. The proponent has demonstrated that the product meets the following standard: CAN/ULC-S702-09, Standard for Mineral Fibre Thermal Insulation for Buildings. The standard describes five types of mineral-fibre insulation. These CCMC Evaluation Listings refer only to preformed insulation, Types 1, 2 and 3. They are defined as follows: Type 1, unfaced; Type 2, faced with a permeable membrane; and Type 3, faced with a vapour barrier. Standard Table 1. Requirements for Preformed Thermal Insulation Test/Property Length Width Thickness Thermal resistance Thermal resistivity Requirements 1%, +3% for batts and rolls. 3 mm, +10 mm for boards and sheets. 0%, +3% for batts and rolls. ± 3 mm for boards. Mean thickness the design thickness and none of the individual specimen thicknesses < 90% of the design thickness. 1 mm, +3 mm for boards. Mean thermal resistance the design thermal resistance (as stated on the product) (m K)/W - 1 -
2 Table 1. Requirements for Preformed Thermal Insulation (cont d) Test/Property Surface burning characteristics Smoulder resistance Breaking load of exterior frame wall sheathing Compressive resistance of draining insulation Water vapour permeance Corrosiveness Fungi resistance Requirements For Type 1 products not intended for exterior of basement walls: Flame-spread classification shall not exceed 25. Smoke developed shall not exceed 50. For Type 2 and 3 the test values shall be reported without reference to the acceptance criteria. Applicable only to Type 1 products, not intended for exterior of Basement walls. Mean mass loss 2% and each specimen 3%. Smoulder zone shall not reach specimen periphery. Not applicable to batts or rolls. 2.7 kg. Applicable only to Type 2 boards for exterior frame wall sheathing. Not applicable to batts or rolls. Applicable to draining insulation only. Compressive resistance for a 38 mm or thicker draining insulation shall be at least 7 kpa at 10% deformation and for thinner than 38 mm it shall be at least 10 kpa at 25% deformation. Batts and Rolls: Not applicable for Type 1 products; 300 ng/(pa s m 2 ) for Type 2 products; 60 ng/(pa s m 2 ) for Type 3 products; and Boards: Applicable to adhered membrane/insulation or to non-adhered membranes. Applicable to Type 1 batts and rolls. Boards: corrosion control. Applicable to Type 1 batts and rolls. Boards: growth comparative item. Marking The standard requires that packaging for the insulation be labelled or marked with the following information: brand name and the name of the manufacturer or supplier; identification of the manufacturing facility location; type of insulation and its intended use; net content of package in m 2 ; number of pieces per package; design linear dimensions of the pieces in the package in mm; design thickness in mm; thermal resistance in (m 2 K)/W to one decimal place; on batts and rolls, the numerical thermal resistance value (or a simple code) displayed on the material at every 1.2 m length; date of manufacture or shift code; statement that the product complies with the standard; and for preformed insulation without a membrane (Type 1 material), except for draining insulation, a cautionary statement: CAUTION: Building, electrical, fire and other applicable codes shall be complied with. All heatemitting devices, such as fuel-burning appliances, chimneys, pipes, ducts and vents to these appliances - 2 -
3 shall maintain a minimum clearance of 50 mm between these devices and the insulation. Recessed light fixtures, unless designed for the purpose, shall not be installed in insulated ceilings. NOTE: Where applicable, the product shall carry additional information as stated below: If the product is intended for application at thicknesses other than the design thickness, the thermal resistance and application for each intended secondary application shall be shown in similar print at a character height of at least ½ that of the design characters (with a minimum of 15 mm). The associated thickness of the secondary application shall also be shown. This secondary application, thermal resistance and thickness information shall be located on the same sides, excluding the ends, of the package as the design thermal resistance, application and thickness designations; and Any necessary user safety information, unless a separate information sheet is provided. NOTE: Depending upon the jurisdiction, additional marking may be required by applicable acts and regulations. National Building Code of Canada (NBC) NBC References The CAN/ULC-S standard is referenced in: (a) NBC 2010, Division B, Table , Table A. and Clause (1)(d)
4 Evaluation Listing CCMC L MASTERFORMAT: Issued: Re-evaluated: Revised: Re-evaluation due: 'Roxul Plus/ComfortBatt' Residential Batt Insulation 1. Evaluation The product conforms to CAN/ULC-S The design thermal resistance values are as indicated in the following table: Design Thickness (mm) Design RSI (m 2 KW -1 ) Description The product is a Type 1, mineral fibre batt insulation that is available in various sizes of friction-fit batts. 3. Standard and Regulatory Information See the Preface and the standard for explanation. 1 of 2
5 Listing Holder: Plant(s): Roxul Inc. 551 Harrop Drive Milton, ON L9T 3H3 Tel: Fax: Milton, ON Grand Forks, BC This Listing is issued by the Canadian Construction Materials Centre, a program of the Institute for Research in Construction at the National Research Council of Canada. The Listing must be read in the context of the entire CCMC Registry of Product Evaluations. Readers must confirm that the Listing is current and has not been withdrawn or superseded by a later issue. Please refer to or contact the Canadian Construction Materials Centre, Institute for Research in Construction, National Research Council of Canada, 1200 Montreal Road, Ottawa, Ontario, K1A 0R6. Telephone (613) Fax (613) NRC has evaluated the material, product, system or service described herein only for those characteristics stated herein. The information and opinions in this Listing are directed to those who have the appropriate degree of experience to use and apply its contents. This Listing is provided without representation, warranty, or guarantee of any kind, expressed, or implied, and the National Research Council of Canada (NRC) provides no endorsement for any evaluated material, product, system or service described herein. NRC accepts no responsibility whatsoever arising in any way from any and all use and reliance on the information contained in this Listing. NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity. 2 of 2
Cellulose Fibre Insulation (CFI) For Buildings
Preface MASTERFORMAT 07 21 23.01 REVISED DATE 2011-04-05 Cellulose Fibre Insulation (CFI) For Buildings Scope These Evaluation Listings apply to treated, wood-based, cellulose fibre intended for use as
More informationSpray-Applied Rigid Polyurethane Foam Insulation, Medium Density
Preface MASTERFORMAT: 07 21 19.02 Issued: 2011-04-13 Spray-Applied Rigid Polyurethane Foam Insulation, Medium Density Scope This Evaluation Listing applies to spray-applied rigid polyurethane foam, medium
More informationEvaluation Listing CCMC L Icynene ProSeal (MD-C-200v3)
CONSTRUCTION Evaluation Listing CCMC 13683-L Icynene ProSeal (MD-C-200v3) Evaluation Issued: 2014-04-16 Re-evaluation due: 2017-04-16 Preface: Masterformat 07 21 19.02, Spray-Applied Rigid Polyurethane
More informationEvaluation Listing CCMC L EcoBay CC CAN / EcoBay CC Arctic CAN
CONSTRUCTION Evaluation Listing CCMC 13359-L EcoBay CC CAN / EcoBay CC Arctic CAN Evaluation Issued: 2011-01-17 Revised: 2012-05-03 Re-evaluation due: 2014-01-17 Re-evaluation in progress Preface: Masterformat
More informationEvaluation Listing CCMC L Boreal Lavender and Boreal Nature
Evaluation Listing CCMC 14025-L Boreal Lavender and Boreal Nature MasterFormat: 07 21 19.02 Evaluation issued: 2015-10-16 Revised: 2016-10-05 Re-evaluation due: 2018-10-16 1. Evaluation The product conforms
More informationEvaluation Report CCMC R Superior Walls Xi Precast Concrete Insulated Wall Panels
CONSTRUCTION Evaluation Report CCMC 13628-R Superior Walls Xi Precast Concrete Insulated Wall Panels MASTERFORMAT: 03 41 10.03 Evaluation issued: 2012-11-08 Revised: 2014-06-05 Re-evaluation due: 2015-11-08
More informationEvaluation Report CCMC R Excel Air Barrier
CONSTRUCTION Evaluation Report CCMC 13565-R Excel Air Barrier MASTERFORMAT: 07 27 09.02 Evaluation issued: 2013-01-30 Re-evaluation due: 2016-01-30 1. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Report CCMC R Icynene ProSeal Air Barrier System
Evaluation Report CCMC 14052-R Icynene ProSeal Air Barrier System MasterFormat: 07 27 09.01 Evaluation issued: 2016-12-23 Re-evaluation due: 2019-12-23 1. Opinion It is the opinion of the Canadian Construction
More informationThis opinion is based on the CCMC evaluation of the technical evidence in Section 4 provided by the Report Holder.
Evaluation Report CCMC 14075-R ZIP System R-sheathing MasterFormat: 06 16 13.01 Evaluation issued: 2017-11-16 Revised: 2018-04-06 Re-evaluation due: 2020-11-16 1. Opinion It is the opinion of the Canadian
More informationEvaluation Report CCMC R Tyvek HomeWrap - Air Barrier Material
CONSTRUCTION Evaluation Report CCMC 12857-R Tyvek HomeWrap - Air Barrier Material MASTERFORMAT: 07 27 09.02 Issued: 1998-03-12 Re-evaluated: 2012-12-18 Revised: 2013-04-10 Re-evaluation due: 2016-03-12
More informationEvaluation Report CCMC R Sto Guard - Air Barrier Material
CONSTRUCTION Evaluation Report CCMC 13120-R Sto Guard - Air Barrier Material MASTERFORMAT: 07 27 09.02 Evaluation issued: 2003-05-26 Re-evaluated: 2012-11-26 Revised: 2013-08-13 1. Opinion It is the opinion
More informationTrex Wood-Polymer Composite Lumber
Evaluation Report CCMC 13125-R MASTERFORMAT 06 73 14.01 Issued 2003-06-24 Re-evaluated 2007-07-20 Revised 2009-01-06 Re-evaluation due 2010-06-24 Re-Evaluation in Progress Trex Wood-Polymer Composite Lumber
More informationCCMC. Graftex CCMC R. EVALUATION DIVISION REPORT Issued
National Research Council Canada Institute for Research in Construction Conseil national de recherches Canada Institut de recherche en construction CCMC 13023-R CCMC Graftex EVALUATION DIVISION 07191 REPORT
More informationEvaluation Report CCMC R Demilec Air Barrier System
Evaluation Report CCMC 14068-R Demilec Air Barrier System MasterFormat: 07 27 09.01 Evaluation issued: 2017-08-30 Re-evaluation due: 2020-08-30 1. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Report CCMC R Surround HouseWrap - Air Barrier Material
CONSTRUCTION Evaluation Report CCMC 13231-R Surround HouseWrap - Air Barrier Material MASTERFORMAT: 07 27 09.02 Evaluation issued: 2006-02-14 Re-evaluated: 2013-06-25 Re-evaluation due: 2015-02-14 1. Opinion
More informationEvaluation Listing CCMC L EverGuard TPO Roofing Products
Evaluation Listing CCMC 14063-L EverGuard TPO Roofing Products MasterFormat: 07 13 54.02 Evaluation issued: 2017-06-07 Re-evaluation due: 2020-06-07 1. Evaluation The product conforms to ASTM D 6878/D
More informationEvaluation Report CCMC R Suretouch
CONSTRUCTION Evaluation Report CCMC 13302-R Suretouch MASTERFORMAT: 07 44 50 Evaluation issued: 2008-03-12 Re-evaluated: 2014-07-02 Re-evaluation due: 2017-03-12 1. Opinion It is the opinion of the Canadian
More informationEvaluation Report CCMC R Colphene ICF, ICF Foundation Membrane, Membrane de Fondation ICF (for dampproofing)
Evaluation Report CCMC 14080-R Colphene ICF, ICF Foundation Membrane, Membrane de Fondation ICF (for dampproofing) MasterFormat: 07 13 26.03 Evaluation issued: 2017-12-20 Re-evaluation due: 2020-12-20
More informationEvaluation Report CCMC R Isofoil
Evaluation Report CCMC 3459-R Isofoil MASTERFORMAT: 07 2 3.03 Issued: 202-09-27 Re-evaluated: 202--27 Revised: 205-03-7 Re-evaluation due: 205-09-27. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Report CCMC R FOAMULAR CodeBord Air Barrier System (CABS)
Evaluation Report CCMC 12935-R FOAMULAR CodeBord Air Barrier System (CABS) MASTERFORMAT: 07 27 09.01 Evaluation issued: 2000-01-24 Re-evaluated: 2016-01-07 Re-evaluation due: 2018-01-24 1. Opinion It is
More informationEvaluation Report CCMC R Trex Transcend Decking
Evaluation Report CCMC 13125-R Trex Transcend Decking MasterFormat: 06 73 14.01 Evaluation issued: 2003-06-24 Re-evaluated: 2017-04-13 Re-evaluation due: 2019-06-24 1. Opinion It is the opinion of the
More informationProduct Information Bulletin
Product Information Bulletin CCMC Evaluation Report 13101-R Advantage Insulating Concrete Forming (ICF) System BULLETIN NO. ISSUED: REPLACES: 201 November 25, 2010 January 2, 2009 Canadian Construction
More informationTimberTech Solid Core Decking 5/4 Plank, TwinFinish and EarthWood
Evaluation Report CCMC 13304-R MASTERFORMAT 06 73 14.01 Issued 2008-01-28 Revised 2008-02-07 Re-evaluation due 2011-01-28 TimberTech Solid Core Decking 5/4 Plank, TwinFinish and EarthWood 1. Opinion It
More informationEvaluation Report CCMC R ZIP System Sheathing and Tape
Evaluation Report CCMC 14019-R ZIP System Sheathing and Tape MasterFormat: 07 25 10.08 Evaluation issued: 2015-08-25 Revised date: 2017-09-01 Re-evaluation due: 2018-08-25 1. Opinion It is the opinion
More informationGerard Shingle, Granite Ridge, and Guardian Shingle
Evaluation Report CCMC 13260-R MASTERFORMAT: 07 41 13 Issued: 2006-09-28 Re-evaluated: 2012-12-17 Re-evaluation due: 2015-12-12 Gerard Shingle, Granite Ridge, and Guardian Shingle 1. Opinion It is the
More informationNovabrik CCMC R. EVALUATION DIVISION REPORT Issued Re-evaluated Revised Re-evaluation
National Research Council Canada Institute for Research in Construction Conseil national de recherches Canada Institut de recherche en construction CCMC 12833-R &&0& EVALUATION DIVISION 04818 REPORT Issued
More informationEvaluation Report CCMC R Fiberon Solid Decking- Horizon, Horizon Symmetry, Sanctuary, and Protect Advantage
Evaluation Report CCMC 13500-R Fiberon Solid Decking- Horizon, Horizon Symmetry, Sanctuary, and Protect Advantage MASTERFORMAT: 06 73 14.01 Issued: 2012-07-31 Re-evaluated: 2015-09-16 Revised: 2017-09-06
More informationEvaluation Report CCMC R DMX Drain 5M (Drainage)
CONSTRUCTION Evaluation Report CCMC 13568-R DMX Drain 5M (Drainage) MASTERFORMAT: 33 46 23.01 Evaluation issued: 2013-05-09 Re-evaluation due: 2016-05-09 1. Opinion It is the opinion of the Canadian Construction
More information1. Opinion. 2. Description. 1 of 5. MasterFormat: Evaluation issued:
Evaluation Report CCMC 14091-R HardieBacker 6.4 mm (1/4 in.) underlayment, HardieBacker 6.4 mm (1/4 in.) EZ Grid underlayment, HardieBacker 10.3 mm (1/2 in.) 500 backerboard MasterFormat: 09 28 13.04 Evaluation
More informationEvaluation Report CCMC R AZEK Deck
CONSTRUCTION Evaluation Report CCMC 3690-R AZEK Deck MASTERFORMAT: 06 73 5.02 Evaluation issued: 204-04-4 Re-evaluated: 204-05-22 Re-evaluation due: 207-04-4. Opinion It is the opinion of the Canadian
More informationEvaluation Report CCMC R NUDURA Waterproofing Membrane
Evaluation Report CCMC 4095-R NUDURA Waterproofing Membrane MASTERFORMAT: 07 3 6.0 Evaluation issued: 08-04-3. Opinion It is the opinion of the Canadian Construction Materials Centre (CCMC) that NUDURA
More informationEvaluation Report CCMC R HELICAL PILE
Evaluation Report CCMC 13675-R HELICAL PILE MasterFormat: 31 62 16.01 Evaluation issued: 2014-07-10 Revised: 2018-01-11 Re-evaluation due: 2020-07-10 1. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Report CCMC R ALMITA HELICAL SCREW PILE
Evaluation Report CCMC 13691-R ALMITA HELICAL SCREW PILE MASTERFORMAT: 31 62 16.01 Evaluation issued: 2015-02-28 Re-evaluation due: 2018-02-28 1. Opinion It is the opinion of the Canadian Construction
More information1. Opinion. 2. Description. MasterFormat: Evaluation issued: Re-evaluated: Evaluation revised:
Evaluation Report CCMC 12678-R HardiePanel HZ5 Vertical Siding, HardiePlank HZ5 Lap Siding, HardieShingle HZ5 Notched Panels and HardieShingle HZ5 Individual Shingle MasterFormat: 07 46 45.01 Evaluation
More informationEvaluation Listing CCMC L Nordic X-Lam
CONSTRUCTION Evaluation Listing CCMC 3654-L Nordic X-Lam Evaluation Issued: 203-2-24 Re-evaluation due: 206-2-24 Preface: Masterformat 06 9 00.02, Cross Laminated Timber (CLT) Panels (Standardized) Preface
More informationEvaluation Report CCMC R Nordic I-Joist Series
CONSTRUCTION Evaluation Report CCMC 13032-R Nordic I-Joist Series MASTERFORMAT: 06 17 33.01 Evaluation issued: 2001-10-29 Re-evaluated: 2014-02-26 Re-evaluation due: 2016-10-29 1. Opinion It is the opinion
More informationPower JoIst ADI-40, ADI-60, ADI-80 I-joists
Evaluation Report CCMC 13053-R MASTERFORMAT DIVISION 06 17 33.01 Issued 2002-03-06 Re-evaluated 2008-09-19 Re-evaluation due 2011-03-06 Power JoIst ADI-40, ADI-60, ADI-80 I-joists 1. Opinion It is the
More informationEvaluation Report CCMC R MetalWorks StoneCrest and MetalWorks AstonWood Steel Shingles
Evaluation Report CCMC 13011-R MetalWorks StoneCrest and MetalWorks AstonWood Steel Shingles MASTERFORMAT: 07 41 13 Evaluation issued: 2001-03-06 Re-evaluated: 2014-12-18 Re-evaluation due: 2017-03-06
More informationEvaluation Report CCMC R WALLTITE v.2 - Air Barrier System
CONSTRUCTION Evaluation Report CCMC 13467-R WALLTITE v.2 - Air Barrier System MASTERFORMAT: 07 27 09.01 Evaluation issued: 2009-08-19 Revised: 2011-12-01 Re-evaluation due: 2012-08-19 Re-evaluation in
More informationArxx High Performance Wallsystems
National Research Council Canada Institute for Research in Construction Conseil national de recherches Canada Institut de recherche en construction CCMC 12641-R &&0& EVALUATION DIVISION 03131 REPORT Issued
More informationEvaluation Report CCMC R Murphy LVL
Evaluation Report CCMC 13507-R Murphy LVL MasterFormat: 06 17 10 Evaluation issued: 2010-10-27 Re-evaluated: 2016-04-18 Revised: 2017-10-18 Re-evaluation due: 2016-10-27 1. Opinion It is the opinion of
More informationEvaluation Report CCMC R Pieux Vissés Vistech / Postech Screw Piles
Evaluation Report CCMC 13102-R Pieux Vissés Vistech / Postech Screw Piles 1. Opinion MASTERFORMAT: 31 62 16.01 Evaluation issued: 2003-02-13 Re-evaluated: 2018-01-04 Re-evaluation due: 2021-02-13 It is
More informationROCKWOOL Board Insulation Section Master Guide Specification Page 1 Jan 2017
Master Guide Specification Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual. 1 GENERAL
More informationEvaluation Report CCMC R StoGuard (w/ Sto Gold Coat and Sto Gold Fill ) sheathing membrane
CONSTRUCTION Evaluation Report CCMC 13612-R StoGuard (w/ Sto Gold Coat and Sto Gold Fill ) sheathing membrane MASTERFORMAT: 07 25 10.05 Evaluation issued: 2012-04-12 Revised: 2012-08-17 1. Opinion It is
More informationFoam-LOK Spray-Applied Rigid Polyurethane Foam Insulation Medium Density
Foam-LOK Spray-Applied Rigid Polyurethane Foam Insulation Medium Density 07216.3 Lapolla Industries, Inc. (Canada) 1870 Albion Rd. Unit 1 Toronto, ON M9W 5T2 416-679-9299 direct 416-679-9399 fax 888-4-LAPOLLA
More informationEvaluation Report CCMC R Insulspan Structural Insulated Panel (SIP) System
Evaluation Report CCMC 13016-R Insulspan Structural Insulated Panel (SIP) System MASTERFORMAT: 06 12 16.01 Issued: 2001-10-29 Re-evaluated: 2013-03-05 Revised: 2015-08-14 Re-evaluation due: 2016-10-29
More informationCANADA COMMERCIAL + RESIDENTIAL Building Insulation Guide
CANADA COMMERCIAL + RESIDENTIAL Building Insulation Guide TABLE OF CONTENTS Here at Johns Manville, we are more than your supplier; we are your channel partner. When you do business with JM, you can count
More informationROCKWOOL Blanket (and Batt) Insulation Section Master Guide Specification (AFB evo ) Page 1 January 2018
Master Guide Specification (AFB evo ) Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual.
More informationEvaluation Report CCMC R Insulspan Structural Insulated Panel (SIP) System
Evaluation Report CCMC 13016-R Insulspan Structural Insulated Panel (SIP) System MasterFormat: 06 12 16.01 Evaluation issued: 2001-10-29 Re-evaluated: 2018-09-26 1. Opinion It is the opinion of the Canadian
More informationROCKWOOL Blanket (and Batt) Insulation Section Master Guide Specification (COMFORTBATT ) Page 1 January 2018
Master Guide Specification (COMFORTBATT ) Page 1 1 GENERAL 1.1 SUMMARY OF WORK.1 This Section specifies mineral fibre batt and blanket thermal insulation for steel stud wall applications. 1.2 RELATED REQUIREMENTS.1
More informationSprayed Polyurethane Foam in Construction. Presented by: Andrew B. Cole, CUFCA, Executive Director
Sprayed Polyurethane Foam in Construction Presented by: Andrew B. Cole, CUFCA, Executive Director Sprayed Polyurethane Foam (SPF) Types of Foams Comparison between open-cell and closed cell SPF physical
More informationTHERMAL BATT INSULATION COMFORTBATT. Thermal Batt Insulation for Residential & Commercial Construction.
THERMAL BATT INSULATION COMFORTBATT Thermal Batt Insulation for Residential & Commercial Construction. Superior building envelope performance by ROCKWOOL Insulation. ROCKWOOL COMFORTBATT is a semi-rigid
More informationCANADA COMMERCIAL + RESIDENTIAL Building Insulation Guide
CANADA COMMERCIAL + RESIDENTIAL Building Insulation Guide TABLE OF CONTENTS Here at Johns Manville, we are more than your supplier; we are your channel partner. When you do business with JM, you can count
More informationGuide Specification SECTION DUCT INSULATION
March 2016 279 Humberline Drive Etobicoke, Ontario M9W 5T6 Canada Toll Free 800-837-8961 Phone 416-798-1340 Fax 416-798-1342 Website www.rfoil.com Email info@rfoil.com Guide Specification Specifier Notes:
More informationROCKWOOL Board Insulation Section Master Guide Specification Page 1 Jan 2017
Master Guide Specification Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual. 1 GENERAL
More informationThe Footing Tube. Evaluation Report GGMC R. lssued:
Evaluation Report GGMC 13309-R MASTERFORMAT: 03 11 13.04 lssued: 2008-04-07 Re-evaluated: 2011-05-29 Re-evaluationdue: 2014-04-07 The Footing Tube 1. Opinion It is the opinion of the Canadian Construction
More informationEvaluation Report CCMC R LP SolidStart LVL
Evaluation Report CCMC 11518-R LP SolidStart LVL MASTERFORMAT: 06 17 10.01 Evaluation issued: 1987-06-03 Revised: 2015-01-13 Re-evaluation due: 2018-04-27 1. Opinion It is the opinion of the Canadian Construction
More informationMULTIPURPOSE BOARD INSULATION ROCKBOARD 40/60/80. Premium Multipurpose Board Insulation for Acoustic/Thermal Applications
MULTIPURPOSE BOARD INSULATION Premium Multipurpose Board Insulation for Acoustic/Thermal Applications ROCKBOARD Products and Applications Product Density Thicknesses W X L Common Applications 4 lb/ft 3
More informationOCC EcoTouch TM QuietZone PINK FIBERGLAS Acoustic Insulation Product Data Sheet
PRODUCT DESCRIPTION PINK acoustic batt insulation fabricated from inorganic glass fibres. PINK TM FIBERGLAS with PureFiber TM Technology is designed to help control noise by absorbing sound vibrations
More informationMaster Specification WALLTITE ECO v.2 by BASF Canada Inc. Section SPRAY POLYURETHANE FOAM INSULATION Page 1
Page 1 WALLTITE ECO v.2 by BASF Canada Inc, is a thermal insulation intended for building enclosures, located in appropriate assembly locations in buildings during enclosure construction. This section
More information.4 Underwriters' Laboratories (UL)..1 UL 2218-[2010], Standard for Impact Resistance of Prepared Roof Covering Materials.
Master Guide Specification (TOPROCK DD PLUS) Page 1 1 GENERAL 1.1 SUMMARY OF WORK.1 This Section specifies roof and deck insulation. 1.2 RELATED REQUIREMENTS.1 Section [ ]. 1.3 REFERENCE STANDARDS.1 ASTM
More informationFIBER GLASS INSULATION. Thermal. Acoustical. Fire Resistant. Moisture Control. Recycled Content. Formaldehyde-free. Air Control FIBER GLASS INSULATION
a a FIBER GLASS INSULATION ComfortTherm Batts and Rolls EasyFit Perforated Batts Unfaced Batts and Rolls Kraft-Faced Batts and Rolls JM Climate Pro /JM Attic Protector Blow-in Insulation JM Spider Blow-in
More informationMaster Specification WALLTITE Eco v.3 by BASF Canada Inc. Section SPRAY POLYURETHANE FOAM INSULATION Page 1
Page 1 WALLTITE ECO v.3 by BASF Canada Inc, is a thermal insulation intended for building enclosures, located in appropriate assembly locations in buildings during enclosure construction. This section
More informationROCKWOOL Roof and Deck Insulation Section Master Guide Specification Page 1 Jan 2017
Master Guide Specification Page 1 1 GENERAL 1.1 SUMMARY OF WORK.1 This Section specifies roof and deck insulation. 1.2 RELATED REQUIREMENTS.1 Section [ ]. 1.3 REFERENCE STANDARDS.1 ASTM International (ASTM)..1
More informationHALO EXTERRA MATERIAL PROPERTY DATA SHEET rev
HALO EXTERRA MATERIAL PROPERTY DATA SHEET PRODUCT NAME Halo Eterra rigid EPS foam insulation MANUFACTURER Beaver Plastics Ltd. 7-2618-TWP RD 51A Acheson, Alberta Canada T7X 5A AMC Foam Technologies Inc.
More informationROCKWOOL Board Insulation Section Master Guide Specification (COMFORTBOARD 110) Page 1 January 2018
Master Guide Specification (COMFORTBOARD 110) Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project
More informationEvaluation Report CCMC R Parallam PSL
Evaluation Report CCMC 11161-R Parallam PSL MasterFormat: 06 17 10 Evaluation issued: 1986-04-03 Re-evaluated: 2015-05-25 Revised: 2017-01-11 Re-evaluation due: 2017-06-14 1. Opinion It is the opinion
More informationHEATLOK SOYA/POLARFOAM SOYA
Spray-in-Place Urethane Foam Insulation page 1/6 HEATLOK SOYA/POLARFOAM SOYA Note: This specification should be adapted for each project. All notes are for guidelines only. An updated.word version could
More informationMaster Specification WALLTITE ECO v.2 by BASF Canada Inc. Section SPRAY POLYURETHANE FOAM INSULATION/AIR BARRIER SYSTEM Page 1
Page 1 WALLTITE ECO v.2 by BASF Canada Inc, is an Air Barrier assembly intended to provide an air and moisture barrier assembly for building enclosures, located in appropriate assembly locations in buildings
More informationPINK BATTS POLYESTER INSULATION. Product. Scope. Building Regulations. Appraisal No. 999 [2018] Appraisal No. 999 (2018) BRANZ Appraisals
OVER 80% RECYCLED GLASS PROVEN SAFE OVER 80% RECYCLED GLASS PROVEN SAFE PINK BATTS POLYESTER BRANZ Appraisals Technical Assessments of products for building and construction. Product 1.1 Pink Batts Polyester
More informationROCKWOOL Board Insulation Section Master Guide Specification (ROCKBOARD 80) Page 1 January 2017
Master Guide Specification (ROCKBOARD 80) Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project
More informationProduct Information Bulletin
Product Information Bulletin BULLETIN NO. ISSUED: REPLACES: 292 March 30, 2017 August 7, 2015 PlastiSpan Insulation use as Continous Insulating Sheathing 2012 Ontario Building Code Page 1 of 5 PlastiSpan
More informationPINK BATTS INSULATION. Product. Scope. Building Regulations. Appraisal No. 238 [2012]
PINK BATTS INSULATION This Appraisal replaces BRANZ Appraisal No. 238 (2008). Amended 29 March 2017 BRANZ Appraisals Technical Assessments of products for building and construction. Product 1.1 Pink Batts
More informationRoxul RHT. Board Roxul RHT. Flex Roxul RHT. Wrap. High Temperature Insulation for Industrial/Mechanical Applications
HigH TemperaTure industrial/mechanical insulation Roxul RHT Board Roxul RHT Flex Roxul RHT Wrap High Temperature Insulation for Industrial/Mechanical Applications roxul rht Protecting High Temperature
More informationOCC QuietZone Acoustic Batt Insulation
PRODUCT DESCRIPTION PINK acoustic batt insulation fabricated from inorganic glass fibres. Acoustic Batt insulation is designed to help control noise by absorbing sound vibrations transmitted through walls,
More informationCanadian Urethane Foam Contractors Association
Canadian Urethane Foam Contractors Association presentation to BECOR 2012-01-18 Mr. Laverne Dalgleish, Principal Building Professionals Laverne is a principal in Building Professionals, Inc. which designs,
More informationSECTION BUILDING INSULATION
SECTION 07210 BUILDING INSULATION Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2010-2011 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Provide stone
More informationROCKWOOL Blanket (and Batt) Insulation Section Master Guide Specification Page 1 Jan 2017
Master Guide Specification Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project Manual. 1 GENERAL
More informationMaster Specification ENERTITE by BASF Canada Inc. Section SPRAY POLYURETHANE FOAM INSULATION Page 1
Page 1 ENERTITE 1-2-1 by BASF Canada Inc, is a thermal insulation intended for building enclosures, located in appropriate assembly locations in buildings during enclosure construction. This section includes
More informationBuilding Regulations
Product 1.1 Technobond is a range of polyester fibre insulation used as thermal and acoustic insulating material in ceilings, roofs and walls of buildings. Appraisal No.69 [010] BRANZ Appraisals Technical
More informationFire-resistant Sound absorbent High density for sag-free, tight fits Green features for sustainable development
Fire-resistant Sound absorbent High density for sag-free, tight fits Green features for sustainable development Batt insulation that fights both fire and noise Roxul s AFB is a lightweight, semi-rigid
More informationROCKWOOL Board Insulation Section Master Guide Specification (CURTAINROCK 80) Page 1 January 2018
Master Guide Specification (CURTAINROCK 80) Page 1 Click on the pilcrow in the MS Word Toolbar to toggle ROCKWOOL GUIDE NOTES on and off. Delete this text before incorporating the section into a Project
More informationEcoTouch Insulation with PureFiber Technology
PROJECT ENGINEER RESPONSIBILITY: This is a general specification guide, intended to be used by experienced construction professionals, in conjunction with good construction practice and professional judgment.
More informationClarifying the Fenestration Energy Performance requirement in the Ontario Building Code Supplementary Standard SB12
Clarifying the Fenestration Energy Performance requirement in the Ontario Building Code Supplementary Standard SB12 February 2012 Legal Notice - Disclaimer and exclusion of liability This document is provided
More informationEARTHWOOL GLASSWOOL INSULATION. Product. Scope. Building Regulations. Appraisal No. 648 [2016]
EARTHWOOL GLASSWOOL This Appraisal replaces BRANZ Appraisal No. 648 (2009) BRANZ Appraisals Technical Assessments of products for building and construction. Product 1.1 Earthwool glasswool insulation is
More informationEvaluation Report CCMC R DC 315 Intumescent Coating
Evaluation Report CCMC 14036-R DC 315 Intumescent Coating MasterFormat: 09 96 48.00 Evaluation issued: 2016-06-03 Re-evaluation due: 2019-06-03 1. Opinion It is the opinion of the Canadian Construction
More informationCURTAINROCK and ROXUL SAFE
CURTAIN WALL SYSTEMS CURTAINROCK and ROXUL SAFE Insulation for Curtain Wall Systems Superior Protection and Performance in a Curtain Wall System Fire Resistant This unique vapor permeable quality Long-Term
More informationBuilding Envelope Design using ROXUL (BEDR ) FIREWALL and ROXUL PLUS MB. Fire Rated Board Insulation for Pre-Engineered Metal Buildings
BUILDING ENVELOPE DESIGN USING ROXUL Building Envelope Design using ROXUL (BEDR ) FIREWALL and ROXUL PLUS MB Fire Rated Board Insulation for Pre-Engineered Metal Buildings ROXUL FIREWALL & ROXUL PLUS MB
More informationGA GYPSUM BOARD TYPICAL MECHANICAL AND PHYSICAL PROPERTIES
The properties described herein were either obtained from laboratory tests conducted under controlled test conditions as set forth in appropriate standards, compiled from manufacturers' literature, or
More informationStandard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks 1
Designation: C 1393 00 Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks 1 This standard is issued under the fixed designation C 1393;
More informationAcoustical Fire Batts
Acoustical Fire Batts Interior Wall Sound Control and Fire Protection Fire resistant Higher density than conventional insulations Excellent sound absorption Sag resistant fit Acoustical Fire Batts FIRE
More informationPinkWood Ltd. Revised September 29, 2017
Fire-Rated Assemblies PR-S315 PinkWood Ltd. Revised September 29, 2017 Products: Series I-Joists PinkWood Ltd., 5929 6 th St. NE, Calgary, Alberta, Canada T2K 5R5 (403) 279-3700 www.pinkwood.ca 1. Basis
More informationBuilding Insulation Submittal Form
Smart Ideas. Better Insulation. Building Insulation Submittal Form Johns Manville has revolutionized the building insulation industry by developing an entire line of formaldehyde-free fiber glass building
More informationBUILDING CODE COMMISSION
Ruling No. 08-24-1198 Application No. 2008-21 BUILDING CODE COMMISSION IN THE MATTER OF Subsection 24(1) of the Building Code Act, S.O. 1992, c. 23, as amended. AND IN THE MATTER OF with Sentence 9.19.1.1.(1)
More informationProRox Board Products Catalogue NEW. High Temperature Board (Slab), Flex and Wrap (Mat) products for Industrial Applications PRODUCT NAMES
HIGH TEMPERATURE INDUSTRIAL/MECHANICAL INSULATION PRODUCT NAMES ProRox Board Products Catalogue High Temperature Board (Slab), Flex and Wrap (Mat) products for Industrial Applications New product names,
More informationProRox 400 Series. Fabricated Industrial Solutions
ProRox 400 Series Fabricated Industrial Solutions ROXUL Fabricated Insulation Solutions The ProRox 400 Series fabricated product line offers board (slab) insulation solutions that can be fabricated into
More informationA4/8 PS AW2324D Issue 10 May Permishield
Insulation A4/8 PS AW2324D Issue 10 May 2018 Vapour-permeable INSULATION MEMBRANE 3-in-1 Insulation, thermal break and vapour-permeable sarking Helps achieve a 6-star house energy rating Fibre-free, non-allergenic,
More informationTER No Use of Icynene Classic Plus Spray Polyurethane Foam (SPF) in Unvented Attics & Crawlspaces
Use of Icynene Classic Plus Spray Polyurethane Foam (SPF) Icynene, Inc. 6747 Campobello Road Mississauga, Ontario, Canada L5N 2L7 jevans@icynene.com Icynene.com TER No. 1703-15 Issue Date: July 8, 2014
More informationBUILDING CODE COMMISSION
Ruling No. 09-17-1229 Application No. 2009-10 BUILDING CODE COMMISSION IN THE MATTER OF Subsection 24(1) of the Building Code Act, S.O. 1992, c. 23, as amended. AND IN THE MATTER OF with Article 9.19.1.1.
More informationNote to Specifier: Use this product for coated glass-mat faced polyisocyanurate insulation boards such as Rboard.
Note to Specifier: Use this product for coated glass-mat faced polyisocyanurate insulation boards such as Rboard. Note to Specifier: Make selections, such as board thickness and sizes, etc. Where selection
More information