m2 Anti-Slip Tape Daylight Fluorescent R13

Transcription

1 Product Description: Daylight Fluorescent and glow in Dark Premium Long Life Durable Self Adhesive Anti-Slip Tape which incorporates a bonded and sealed 60-grit Aluminium Oxide, on an EN71 Low Temperature Resistant PVC Film which has been coated with a highly water and shrink resistant Acrylic Co-Polymer Pressure Sensitive Adhesive, protected by an easy-to-remove Release Liner Applications: Ideal use for commercial, industrial and private areas. Usable on smooth, wet substrates or substrates smeared with oil or grease, with high traffic and low forklift traffic. - Internal and external areas - Entrances, passages, paths - Steps, slopes, ramps - Smooth Metal surfaces - Machines, vehicles - Kitchens, canteens - Terraces, shelters Properties: Sizes: - Excellent slip-prevention rated to R13 according to BGR Luminance 140/18 mcd/m² (600% above DIN 67510) - Strong, long life adhesive - Durable, highly wear and tear resistant can be walked on immediately after installation - Resistant to most chemicals and mineral oils - Forklift traffic resistant - Usable on nearly all surfaces - Available in rolls with standard widths of 25 mm and 50 mm width, 6 m length (stock articles) - Available in rolls with individual width, 6 m or 18,3 m length (n-stock articles) - Pre-cut strips (stock articles) - Custom die cuts (n-stock articles) Mehlhose Antirutschprodukte GmbH Page 1 of 7

2 Technical Data: Components Grit Tape: - Epoxy Top Coat - 60-grit Aluminium Oxide - Acrylic Co-Polymer Adhesive - EN71 Low Temperature Resistant PVC Film - Acrylic Pressure Sensitive Co-Polymer Adhesive Release Liner: - Silicone - Paper Property Test Method Result Thickness Micrometer - Total (Grit Tape + Release Liner) 1,00mm - Grit Tape 0,80mm - Adhesive 0,05mm Overall Mass (Grit Tape + Release Liner) Electronic Balance 850g/m² Tensile Strength (Grit Tape) ASTM D882 - Machine Direction 7500g/25mm - Across Machine Direction 6500g/25mm Elongation at Break ASTM D882 - Machine Direction 50% - Across Machine Direction 25% 180 Degree Peel Adhesion on Stainless Steel DIN EN ,5N/10mm 90 Degree Peel Adhesion on Stainless Steel PSTC 14-1 hour 1600g/25mm - 24 hours 1800g/25mm Rolling Ball Tack - Number 15 Ball ASTM cm Adhesive Shear PSTC hours Release Force PSTC 8 30g/25mm Conical Mandrel Bend Test ASTM D522 5cm Mehlhose Antirutschprodukte GmbH Page 2 of 7

3 After Heat Aging at 70 C for 168 hours - Adhesion and Tensile properties shall t decline by more than 15% - Release property shall t increase by more than 25% - There shall be color change or other change in appearance - Product shall bend over a 25mm Mandrel without cracking As per methods above Mounted Shrinkage 10x10cm on Stainless 70 C/168 hr 0,50mm Slip Resistance DIN R13 Slip Resistance Wessex Pendulum Test - Dry 75 - Wet 75 Luminance 600% above DIN DIN after 10min in the dark 140mcd/m² - after 60min in the dark 18mcd/m² - fading time 25 hours REACH Compliance REACH Yes RoHs Compliance RoHs Yes Service Temperature Range Service Duration Shelf Life (+15 C to +30 C, dry) -10 C to +60 C 1 Million Crossings 24 Months Oil-, Chemical-, UV-Resistance - Engine oil, gear oil, hydraulic oil, fuel good - Liquid anti-freeze, liquid soap, water good - Sulphuric acid, alcohol good - UV moderate Recommended Accessories - 3M Scotch-Weld Tape Primer 83 for porous and structured substrates - 3M Scotch-Weld Contact Rubber Adhesive 2141 for wooden, concrete asphalt and rubber substrates - 3M Edge Sealing Compound for permanent moisture or on structured substrates - Rubber Roller for best activation of pressure sensible adhesion Mehlhose Antirutschprodukte GmbH Page 3 of 7

4 Installation Instruction Important Notice: Our anti-slip tapes are do-it-yourself products. They can be installed quickly and easily and do t require any special skills. Just follow the Preparation, Installation and Maintenance Instructions to achieve best results. Failure to do so might result in below par performance. 1. Ambient Conditions a) Surface must be firm, smooth, dry, clean, n-flaking, n-porous and free from waxes and oils. b) Do t apply our anti slip tapes on surfaces that are permanently wet and on quarry tiles in commercial kitchens. c) Paint and lacquers must be thoroughly dry, free of residual solvents, surface waxes and silicones. d) Minimum Temperature for proper Application must be >+12 C constantly for a combined period of at least 48 hours (24 hours before application and 24 hours after application). e) Pay attention to expected weather conditions when installing outside. 2. Surface Preparation a) Remove dirt, grease, dust and chipped, cracked or peeled paint from surface. Strip waxed floors prior to washing. Use appropriate cleaner or solvent wipe to clean surface. b) Degreasing wash is recommended for porous concrete, painted concrete, vinyl tiles, marble and terrazzo ceramic. Strip off floor finish from vinyl, marble and terrazzo ceramic tiles before washing. c) Solvent wiping is recommended for bare metal, polyethylene and polypropylene. d) Solvent wiping or a degreasing wash is recommended for painted metal, painted plastics, painted wood, gelcoated fibre glass and epoxy floors. e) Following a degreasing wash you should rinse twice and dry the surface completely. Wait at least one hour before application of tapes, making sure that the surfaces are completely dry. f) Following solvent wiping give solvents 10 minutes to fully evaporate before application of tapes. g) If you do t use a primer (see. 3.) warm the surface and tapes prior to actual application. 3. Prime Coat Prime Coat is recommended for proper adhesion on the following surfaces: All treated and untreated Wood surfaces, if t already lacquer sealed. All Concrete and Asphalt surfaces. All rough or smooth, porous surfaces. Priming Instructions: a) Properly clean the floor following Surface Preparation procedure. b) Use a paint brush and paint on a thin coat (0.5mm) of primer where the anti slip tapes are to be applied. Mehlhose Antirutschprodukte GmbH Page 4 of 7

5 c) Allow the primed area to dry thoroughly for minutes (depending on temperature) and make sure there is evidence of stickiness or tackiness. (all solvent must have evaporated). d) Primers are t recommended for clear grade tapes due to loss of the transparency benefit. 4. Application a) If you are t applying custom made die cut sheets then cut pieces from a roll of tape. Maximum length of pieces should t exceed 1m. b) Always round the corners. Trim with a suitable cutting tool. c) Important tice before application: On steps, apply tapes 5-10mm from stair edge to prevent edge curl and premature wear. Do t bridge over grouting, cracks or breaks in all surfaces. Cut into smaller pieces. Individual pieces should be spaced a minimum of 5-10mm and a maximum of 50mm apart. Do t bend anti slip tapes. d) Peel protective liner back about 50 mm from one end and position piece on surface. Note: minimize touching (contaminating) adhesive with fingers. e) Continue to remove the protective release liner and press the tape firmly into place as the liner is removed. f) For small pieces, peel liner off piece at a time. Holding the piece by its edges, curve it gently with the adhesive side out. Align the middle of the piece over the middle of the target surface and press down. g) Finally press into firm contact with surface using a rubber hand roller (hard rubber, roll width should t exceed 70mm) by starting in middle and rolling out towards edges. Avoid air enclosures and press extra strong along edges. h) For applying Conformable treads, hammer the tape use a soft-headed rubber mallet to ensure that the product conforms to the surface. Pound edges extra hard. i) After application anti slip tapes can be walked on immediately. However, adhesion requires up to 72 hours in achieving full performance. Temperature should t decrease substantially within this time frame. 5. Edge Sealing For extra protection from excessive moisture or liquids (t constant moisture) use a clear Edge Sealing Compound to protect the edges of anti slip tapes against penetration of liquids. After edge sealing the anti slip tape must t be walked within 2-3 hours and it needs about 2-3 days to fully dry the edge sealing compound. Heavy duty traffic must t use the area during this period. 6. Cleaning and Maintenance Periodically inspect product application to maintain product effectiveness and ensure serviceability. Regularly scrub the treads with a stiff bristle brush to ensure that they are kept free of dirt and other residue that might impair functionality. General Purpose, Coarse & Conformable treads should be decked-brushed regularly. Resilient materials should be mopped or deck-brushed regularly. Use appropriate degreaser/cleaner as a general maintenance cleaner, wash and rinse with water to keep material and surrounding surfaces free of soil and grease. Mehlhose Antirutschprodukte GmbH Page 5 of 7

6 Additional Installation Instructions 1. Overview of the surface preparation Cleaning with solvents 2) Cleaning with floor cleaner Primer/ Adhesion layer 2) Metals, blank or Metals, coated or if necessary adhesion layer Wood, untreated Primer Wood, coated or if necessary Primer Concrete, Screed, Cement 1) Primer Cement, sealed, coated Primer GRP or if necessary adhesion layer Plastics, coated Vinyl-Asbestos-Tiles Terrazzo/Marble Ceramic tiles 1) or if necessary adhesion layer Epoxy coated floors 1) For concrete, screed, cement and ceramic tiles-consider the followed instructions. 2) Recommendation: Solvents acetone, commercial Primer 3M Scotch-Weld 2141 Adhesive layer 3M Scotch-Weld 83 adhesive layer Mehlhose Antirutschprodukte GmbH Page 6 of 7

7 2. Chart for ceramic tiles and concrete Type of floor lining Surface Installation of anti-slip tapes possible Ambience Inmplements 3) yes dry areas Adhesive layer and poss. Edge Sealing structured humid areas Glazed Stoneware tile yes outdoors dry areas even yes humid areas Edge Sealing outdoors structured Unglazed Stoneware tile yes dry areas Edge Sealing Concrete even humid areas Screed,Cement outdoors Mosaic stoneware Strictly t! Sure of step tiles glazed or unglazed Strictly t! 3) Recommendation: Adhesive layer 3M Scotch-Weld 83 Edge Sealing 3M Safety Walk Edge Sealing Mehlhose Antirutschprodukte GmbH Page 7 of 7