Grinnell Mechanical Products Figure 730 Mechanical Tees - Threaded / Grooved General Description. Technical Data. Page 1 of 8 MAY, 2009 G210

Size: px

Start display at page:

Download "Grinnell Mechanical Products Figure 730 Mechanical Tees - Threaded / Grooved General Description. Technical Data. Page 1 of 8 MAY, 2009 G210"

Hollie McDaniel
5 years ago
Views:

Technical Services: Tel: (866) 500-4768 / Fax: (401) 781-7317 www.grinnell.

1 Technical Services: Tel: (866) / Fax: (401) Grinnell Mechanical Products Mechanical s - Threaded / Grooved General escription The Mechanical s may be used for any tee connection where a threaded or grooved outlet is needed. They may be converted into a cross when necessary. notice The Mechanical described herein must be installed and maintained in compliance with this document, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintaining their system and devices in proper operating condition. The installing contractor or manufacturer should be contacted with any questions. Technical ata Outlet Threaded or Grooved Working Pressure 500 psi (34.5 ar) Note: Maximum pressure applies to the Mechanical. When connected to a grooved coupling, the rating will be the lesser of the Mechanical or oupling rating. Maximum pressure is a total from all loads, based on standard weight steel pipe. For pipe with other wall thickness or materials contact Tyco Fire & uilding Products. pprovals UL, FM, UL, VdS, and LP Housing uctile iron conforming to STM -536, Grade Protective oatings Non-lead orange paint RL red (optional) non-lead paint Hot dipped galvanized conforming to STM -153 olt/nuts Track Head olts - conforming to STM -183, Zinc Plated, ( Tensile = 110,000 psi/758,422 kpa) Metric - conforming to STM F568M Gasket (specify when ordering) Grade E EPM, green color code -30 F (-34 ) to +230 F (+110 ) Grade T Nitrile, orange color code -20 F (-29 ) to +180 F (+82 ) (See ata Sheet G610 for aid in selecting proper gasket.) FM For Fire Protection pressure rating, listing and approval information, contact Tyco Fire & uilding Products. Page 1 of 8 MY, 2009 G210

2 Page 2 of 8 G210 E ranch Outlet with Female NPT/ISO 7-1 Threaded ranch ( onfiguration) ranch Outlets with Female NPT/ISO 7-1 Threaded ranch (ross onfiguration) threaded Outlets ranch Outlet with one Female NPT/ISO 7-1 Threaded ranch and one Grooved ranch* (ross onfiguration) Run x ranch NSI N Hole ia. ranch End Load Nominal imensions- E olt** / pprox. ross pprox. 2 x 1/2 N50 x N15 2 x 3/4 N50 x N20 2 x 1 N50 x N25 2 x 1-1/4 N50 x N32 2 x 1-1/2 N50 x N40 2-1/2 x 1/2 N65 x N15 2-/4 N65 x N20 2-1/2 x 1 N65 x N25 2-1/2 x 1-1/4 N65 x N32 2-1/2 x 1-1/2 N65 x N40 2-1/2 x 2 N65 x N mm x 1/2 N65 x N mm x 3/4 N65 x N mm x 1 N65 x N mm x 1-1/4 N65 x N mm x 1-1/2 N65 x N mm x 2 N65 x N50 3 x 1/2 N80 x N (66,5) 2.62 (66,5) 2.62 (66,5) (73,2) (73,2) (73,2) 3.00 (76,2) (74,5) 2.94 (74,5) 2.94 (74,5) 3 (79,5) 3.25 (82,6) (91,2) 2.12 (53,8) 2.12 (53,8) 2.12 (53,8) 1.93 (49,0) 1.93 (49,0) 2.38 (60,5) 2.38 (60,5) 2.38 (60,5) 2.19 (55,6) 2.17 (55,1) 2.44 (62,0) 2.44 (62,0) 2.44 (62,0) 2.44 (62,0) 2.25 (57,2) 2.25 (57,2) 6 (65,0) 2.2 (1,0) 2.2 (1,0) 2.2 (1,0) (1,1) (1,1) 3.5 (1,6) 4.1 (1,7) (1,7) (1,8) (2,0) (1,8) 5.1 (2,3) (2,0) Proper hole preparation is required for effective sealing and performance. heck the pipe seal surface within 5 /8 (15.9mm) of the hole to be certain it is free from conditions that would affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area, that might affect assembly, proper seating of the locating collar or flow from the outlet. For crosses, ensure double outlet holes are aligned on opposite sides of the pipe. The use of threaded products other than steel pipe, such as dry pendent sprinklers, etc. may not be compatible with the female threaded outlet on the Mechanical. lways confirm compatibility by contacting Tyco Fire & uilding Products. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. ontact Tyco Fire & uilding Products for details. * See pages 5 & 6 for grooved dimensions. Note: Outlet Threads conforming to ISO 7-1 are available, contact Tyco Fire & uilding Products. Figure 1 (1 of 3) Mechanical Outlet and ross (Threaded)

3 G210 Page 3 of 8 E ranch Outlet with Female NPT/ISO 7-1 Threaded ranch ( onfiguration) ranch Outlets with Female NPT/ISO 7-1 Threaded ranch (ross onfiguration) threaded Outlets ranch Outlet with one Female NPT/ISO 7-1 Threaded ranch and one Grooved ranch* (ross onfiguration) Run x ranch NSI N Hole ia. ranch End Load Nominal imensions- E olt** / pprox. ross pprox. 3 x 3/4 N80 x N (65,0) (1,7) 4.5 (2,0) 3 x 1 N80 x N (65,0) (1,7) 4.5 (2,0) 3 x 1¼ N80 x N32 4 (84,8) (1,8) 4.9 (2,2) 3 x 1½ N80 x N40 8 (85,9) 2.48 (63,0) x 2 N80 x N (103,9) 4.7 (2,1) 6.5 (2,9) 4 x 1/2 N100 x N (93,7) 4 x 3/4 N100 x N (93,7) 4 x 1 N100 x N (93,7) 4 x 1¼ N100 x N32 2 (99,6) 3.00 (76,2) 4 x 1½ N100 x N (75,7) 4 x 2 N100 x N (82,6) (3,7) 4 x 2½ N100 x N65 2 (79,2) (3,7) 4 x 76.1mm N100 x N65 2 (79,2) (3,7) 4 x 3 N100 x N (104,9) 1 (84,1) (6,1) 5 x 1½ N125 x N40 (117,6) 5/8 x 43/4 6.5 (2,9) 7.7 (3,5) 5 x 2 N125 x N50 (117,6) 3.88 (98,6) 5/8 x 43/4 (3,7) 5 x 2½ N125 x N (120,7) 3.88 (98,6) 5/8 x 43/4 7.3 (3,3) 8.7 (3,9) 5 x 76.1mm N125 x N (120,7) 3.88 (98,6) 7.3 (3,3) 8.7 (3,9) Proper hole preparation is required for effective sealing and performance. heck the pipe seal surface within 5 /8 (15.9mm) of the hole to be certain it is free from conditions that would affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area, that might affect assembly, proper seating of the locating collar or flow from the outlet. For crosses, ensure double outlet holes are aligned on opposite sides of the pipe. The use of threaded products other than steel pipe, such as dry pendent sprinklers, etc. may not be compatible with the female threaded outlet on the Mechanical. lways confirm compatibility by contacting Tyco Fire & uilding Products. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. ontact Tyco Fire & uilding Products for details. * See pages 5 & 6 for grooved dimensions. Note: Outlet Threads conforming to ISO 7-1 are available, contact Tyco Fire & uilding Products. Figure 1 (2 of 3) Mechanical Outlet and ross (Threaded)

4 Page 4 of 8 G210 E ranch Outlet with Female NPT/ISO 7-1 Threaded ranch ( onfiguration) ranch Outlets with Female NPT/ISO 7-1 Threaded ranch (ross onfiguration) threaded Outlets ranch Outlet with one Female NPT/ISO 7-1 Threaded ranch and one Grooved ranch* (ross onfiguration) Run x ranch NSI N Hole ia. End Load (ranch) Nominal imensions- E olt** / pprox. ross pprox. 5 x 3 N125 x N mm x 1-1/4 N150 x N mm x 1-1/2 N150 x N mm x 2 N150 x N mm x 2-1/2 N150 x N mm x 76.1mm N150 x N mm x 3 N150 x N mm x 4 N150 x N100 6 x 1-1/4 N150 x N32 6 x 1-1/2 N150 x N40 6 x 2 N150 x N50 6 x 2-1/2 N150 x N65 6 x 3 N150 x N80 6 x 4 N150 x N100 8 x 2-1/2 N200 x N65 8 x 76.1mm N200 x N65 8 x 3 N200 x N80 8 x 4 N200 x N (127,0) 0 (139,7) 5.38 (136,7) 0 (139,7) 5.38 (136,7) 6.25 (158,8) 6.25 (158,8) 6.50 (165,1) 6.38 (162,1) (108,0) 4.04 (102,6) 4.31 (109,5) 4.18 (106,2) 4.18 (106,2) 4.37 (111,0) 4.56 (115,8) 4.25 (108,0) 4.04 (102,6) 4.31 (109,5) 4.18 (106,2) 4.37 (111,0) 4.56 (115,8) 5.12 (130,0) 5.12 (130,0) 5.37 (136,4) 6 (141,2) 5/8 x 43/4 3/4 x 4¾ 3/4 x 4¾ 3/4 x 4¾ 6.9 (3,1) 9.5 (4,3) 10.0 (4,5) 6.9 (3,1) 9.5 (4,3) 10.0 (4,5) 10.2 (4,6) 10.2 (4,6) 1 (5,7) 1 (5,7) 14.7 (6,7) 7.9 (3,6) 14.1 (6,4) 20.1 (9,1) 7.9 (3,6) 14.1 (6,4) 20.1 (9,1) 12.1 (5,5) 12.1 (5,5) 15.1 (6,8) 21.1 (9,6) Proper hole preparation is required for effective sealing and performance. heck the pipe seal surface within 5 /8 (15.9mm) of the hole to be certain it is free from conditions that would affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area, that might affect assembly, proper seating of the locating collar or flow from the outlet. For crosses, ensure double outlet holes are aligned on opposite sides of the pipe. The use of threaded products other than steel pipe, such as dry pendent sprinklers, etc. may not be compatible with the female threaded outlet on the Mechanical. lways confirm compatibility by contacting Tyco Fire & uilding Products. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. ontact Tyco Fire & uilding Products for details. * See pages 5 & 6 for grooved dimensions. Note: Outlet Threads conforming to ISO 7-1 are available, contact Tyco Fire & uilding Products. Figure 1 (3 of 3) Mechanical Outlet and ross (Threaded)

5 G210 Page 5 of 8 ranch Outlet with Grooved ranch ( onfiguration) Run x ranch NSI N 2 x 1-1/4 N50 x N32 2 x 1-1/2 N50 x N40 2-1/2 x 1-1/4 N65 x N32 2-1/2 x 1-1/2 N65 x N40 2-1/2 x 2 N65 x N mm x 1-1/4 N65 x N mm x 1-1/2 N65 x N mm x 2 N65 x N50 3 x 1-1/4 N80 x N32 3 x 1-1/2 N80 x N40 3 x 2 N80 x N50 4 x 1-1/4 N100 x N32 4 x 1-1/2 N100 x N40 4 x 2 N100 x N50 4 x 2-1/2 N100 x N65 4 x 76.1mm N100 x N65 4 x 3 N100 x N80 5 x 1-1/2 N125 x N40 5 x 2 N125 x N50 5 x 2-1/2 N125 x N65 Hole ia. 63,5 End Load (ranch) ranch Outlets with Grooved ranch (ross onfiguration) Grooved Outlets Nominal imensions (66,5) 3.00 (76,2) 9 3 (79,5) 3.25 (82,6) 4 (84,8) 8 (85,9) 2 (99,6) 4.13 (104,9) (117,6) (117,6) 4.75 (120,7) 3.59 (91,2) 4.09 (103,9) ranch Outlet with one Female NPT/ISO 7-1 Threaded ranch* and one Grooved ranch (ross onfiguration) olt** 1/2 x 3 1/2 x 3 1/2 x 3 1/2 x 3 pprox. (1,1) (1,1) 3.5 (1,6) 4.1 (1,8) (2,1) (2,9) 7.3 (3,3) ross pprox. Lbs./(kg) Proper hole preparation is required for effective sealing and performance. heck the pipe seal surface within 5/8 (15.9mm) of the hole to be certain it is free from conditions that would affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area, that might affect assembly, proper seating of the locating collar or flow from the outlet. For crosses, ensure double outlet holes are aligned on opposite sides of the pipe. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. ontact Tyco Fire & uilding Products for details. * See pages 2, 3 & 4 for threaded dimensions. figure 2 (1 of 2) Mechanical Outlet and ross (Grooved)

6 Page 6 of 8 G210 ranch Outlet with Grooved ranch ( onfiguration) Run x ranch NSI N 5 x 76.1mm N125 x N65 5 x 3 N125 x N mm x 1-1/4 N150 x N mm x 1-1/2 N150 x N mm x 2 N150 x N mm x 2-1/2 N150 x N mm x 76.1mm N150 x N mm x 3 N150 x N mm x 4 N150 x N100 6 x 1-1/4 N150 x N32 6 x 1-1/2 N150 x N40 6 x 2 N150 x N50 6 x 2-1/2 N150 x N65 6 x 3 N150 x N80 6 x 4 N150 x N100 8 x 2-1/2 N200 x N65 8 x 76.1mm N200 x N65 8 x 3 N200 x N80 8 x 4 N200 x N100 Hole ia. End Load (ranch) ranch Outlets with Grooved ranch (ross onfiguration) Grooved Outlets Nominal imensions (120,7) 5.00 (127,0) 0 (139,7) 5.38 (136,7) 0 (139,7) 5.38 (136,7) 6.25 (158,8) 6.25 (158,8) 6.50 (165,1) 6.38 (162,1) (90.4) ranch Outlet with one Female NPT/ISO 7-1 Threaded ranch* and one Grooved ranch (ross onfiguration) olt** 3/4 x 4-3/4 3/4 x 4-3/4 3/4 x 4-3/4 pprox. 7.3 (3,3) (3,1) 9.5 (4,3) 10.0 (4,5) 6.9 (3,1) 9.5 (4,3) 10.0 (4,5) 10.2 (4,6) 10.2 (4,6) 1 (5,7) 1 (5,7) ross pprox (3,6) 14.1 (6,4) 20.1 (9,1) 7.9 (3,6) 14.1 (6,4) 20.1 (9,1) 12.1 (5,5) 12.1 (5,5) 15.1 (6,8) 21.1 (9,6) Proper hole preparation is required for effective sealing and performance. heck the pipe seal surface within 5/8 (15.9 mm) of the hole to be certain it is free from conditions that would affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area, that might affect assembly, proper seating of the locating collar or flow from the outlet. For crosses, ensure double outlet holes are aligned on opposite sides of the pipe. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. ontact Tyco Fire & uilding Products for details. * See pages 2, 3 & 4 for threaded dimensions. figure 2 (2 of 2) Mechanical Outlet and ross (Grooved)

7 G210 Page 7 of 8 Limited Warranty Products manufactured by Tyco Fire & uilding Products (TFP) are warranted solely to the original uyer for ten (10) years against defects in material and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFP. No warranty is given for products or components manufactured by companies not affiliated by ownership with TFP or for products and components which have been subject to misuse, improper installation or maintenance, corrosion, or other external sources of damage. Materials found by TFP to be defective shall be either repaired or replaced, at TFP s sole option. TFP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. TFP shall not be responsible for system design errors or inaccurate or incomplete information supplied by uyer or uyer s representatives. In no event shall TFP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential damages, including but not limited to labor charges, regardless of whether TFP was informed about the possibility of such damages, and in no event shall TFP s liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, express or implied, including warranties of merchantability and fitness for a particular purpose. This limited warranty sets forth the exclusive remedy for claims based on failure of or defect in products, materials or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full extent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure When placing an order, indicate the full product name. Please specify the quantity, size, (NSI inch size or pipe O..), figure number, type of gasket: Grade E EPM Grade T Nitrile Grinnell Mechanical Products, valves, accessories and other products are available throughout the U.S., anada, and internationally, through a network of distribution centers. You may write directly or call for the distributor nearest you. General Notes: It is the esigner s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data are not exceeded. lways read and understand the installation instructions (IH-1000M). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified to be compatible for the specific application. ertified ompany

8 Page 8 of 8 G TYO FIRE SUPPRESSION & UILING PROUTS, 451 North annon venue, Lansdale, Pennsylvania 19446

G-FIRE GROOVED COUPLINGS

G-FIRE GROOVED COUPLINGS Figure 5 G-FIRE Rigid Page 5 Figure 5 Flexible Page GRINNELL are designed for grooved end pipe and are available in nominal sizes of 25mm (") to 3mm (2") including BS, and ISO