TRUMAN STATE UNIVERSITY OPHELIA PARRISH FINE ARTS CENTER ACOUSTICAL RENOVATIONS TABLE OF CONTENTS DIVISION 21 FIRE PROTECTION SYSTEM
|
|
- Rosalind Reynolds
- 5 years ago
- Views:
Transcription
1 TABLE OF CONTENTS DIVISION 21 FIRE PROTECTION SYSTEM FIRE PROTECTION SYSTEM GENERAL REFERENCES, REGULATORY REQUIREMENTS REFERENCES, RELATED SECTIONS of the SPECIFICATIONS DEFINITIONS WORK INCLUDED SUBMITTALS SPECIAL REQUIREMENTS CLOSE-OUT REQUIREMENTS DESIGN WATER SUPPLY LAYOUT - GENERAL to all SPRINKLER SYSTEMS APPROVALS TESTING ACCEPTANCE SPACE CLASSIFICATION SERVICE ENTRANCE VALVES PIPING MATERIAL and FITTING SCHEDULE WET PIPE SPRINKLER SYSTEM SPRINKLER HEADS AREAS SUBJECT to FREEZING... 6 TABLE OF CONTENTS TOC-1
2 THIS PAGE INTENTIONALLY LEFT BLANK
3 FIRE PROTECTION SYSTEM GENERAL A. This section specifies a hydraulically calculated fire protection system designed and installed by the Contractor as described on the drawings and hereinafter. B. It is the intent that the drawings and specifications shall describe and provide for a working installation complete in every detail and all items necessary for such complete installation shall be furnished whether specifically mentioned or not. C. The Plans, the general provisions of the Contract including the General, Supplementary and/or Special Conditions and specification sections of Division 1 shall apply to Work of Divisions of the Specifications. D. Provisions and conditions cited in this Section shall apply to Work for other sections of Divisions of these Specifications REFERENCES, REGULATORY REQUIREMENTS A. Work for this Section of the Specifications shall be performed in accordance with the Codes, Standards, etc. as identified in Division 20 in addition to the following: 1. National Fire Protection Association (NFPA) 13, The Local Authority having jurisdiction REFERENCES, RELATED SECTIONS OF THE SPECIFICATIONS Requirements of the following Sections of the Specifications apply to Work for this Section: A. Division 20 - Basic Mechanical Conditions. B. Division 20 - Basic Mechanical Materials and Methods DEFINITIONS A. The term layout where used in this Section of the Specifications shall mean drawings prepared by the Contractor showing where all piping and heads are located. These drawings should include pipe elevations, need not include pipe sizes and should not include hydraulic calculations. B. The term Authority Having Jurisdiction or AHJ where used in this Section of the Specification shall mean the organization, office, or individual responsible for approving equipment, an installation, or a procedure. C. The term rhythm where used in this Section of the Specifications shall mean spaced in a manner which would place the heads at the same location with respect to lights or diffusers (i.e., for a row of lights spaced at 12' centers heads shall also be on 12' centers so that the heads will remain the same number of ceiling tiles or distance away from the lights; where there is an odd number of tiles between lights or diffusers, it is also preferable to have heads located at the tile centered between them). FIRE PROTECTION SYSTEM 21-1
4 D. The term working drawings where used in this Section of the Specifications shall mean drawing of the quality and containing all information as which would be required for approval by local official and for field construction WORK INCLUDED A. Furnish material, labor and services necessary for and incidental to the installation of the following systems where shown on the Plans and as hereinafter specified. Include all necessary work in the related sections of the Specifications (Subsection to perform the Work completely. B. Furnish and install a complete hydraulically engineered extension of the building fire protection system including the addition of heads on existing branch lines. 1. Hydraulic calculations shall include the domestic water demand in all common piping back to the point of the flow test. C. Verify actual water supply with a test, preferably witnessed or performed by the local fire official. D. Contractor shall coordinate his work with the work of other trades, and with the architectural and structural drawings SUBMITTALS A. The Contractor shall prepare submittals for approval in accordance with Subsection , Duties of Contractor - Submittals. B. Submit Layout drawings and equipment cut sheets with 30 days from the General Contractor s contract date SPECIAL REQUIREMENTS A. The Contractor preparing the drawings and calculations shall be NICET Level 3 certified or a Professional Engineer licensed in the State of Missouri whichever is required by the Authority Having Jurisdiction. B. All equipment shall be U.L. Listed or F.M. approved for use in fire protection systems CLOSE-OUT REQUIREMENTS A. Reference Section B. Where NFPA maintenance information is utilized, it shall be edited to contain only information that is relevant to this project DESIGN WATER SUPPLY A. The water supply shall be a connection to the (City) water supply. B. A new flow test witnessed by the Fire Marshal shall be conducted. C. This information is provided for general information only. FIRE PROTECTION SYSTEM 21-2
5 D. Design water pressure requirements shall include a minimum of [10-psi] safety factor. Where Authority having jurisdiction requires a higher safety factory it shall be used. E. The point of this Contractor's work shall start where determined by the General Contractor and local trade practices LAYOUT - GENERAL TO ALL SPRINKLER SYSTEMS A. The layout shall be submitted to the Architect prior to performing hydraulic calculation, sizing pipes or seeking approvals from the authority having jurisdiction. B. The Architect/Engineer will review layout for aesthetics, and pipe routings for consistency with the construction documents. C. Minimum head spacing shall be as per NFPA-13., additional heads may be required by the Architect/Engineer to create spacing that works with the reflected ceiling plans. Contractor shall layout any areas not shown on the plans with symmetry and rhythm in mind. D. Heads shall be on return bends and centered ± 1 for ceiling clouds. E. Contractor shall not scale the drawing, refer to architectural drawings for dimensions. Where the room dimension is at the maximum size listed for the sprinkler heads, install an additional row of sprinklers. F. Contractor shall locate heads in the field from the final wall locations. It shall be brought to the Architect s/engineer s attention where the center of tile location exceeds the maximum distance of the sprinkler. Additional heads shall be added and the layout modified as directed by the Architect/Engineer at no additional cost to the Owner. G. All sets and rises shall be located above ceilings of adjacent spaces of rooms without ceilings as opposed to making the sets and risers in the exposed spaces. H. Inspector test connections and auxiliary drains shall be piped to spaces not occupied by building occupants, i.e., Mechanical Rooms, Storage Rooms, Janitor's Closets, etc APPROVALS A. Submittal drawings shall show lights, ducts, and pipes indicating all necessary rises and drops in sprinkler piping required for routing. Drawings shall be of a minimum of the same scale as the contract documents (1/8 = 1'-0 scale, ¼ = 1'-0 scale.). A ¼ scale drawing of the service entrance and an elevation of the service entrance shall be required. A sprinkler riser diagram showing all control valves, test connections, supervisory switches, and drains shall be required. B. The layout submittals shall contain at least two (2) copies of reproducible sepias of piping layout. Equipment cut sheets shall also be provided at this time. C. Any pipe sizing or hydraulic calculations performed prior to the Contractor receiving the layout submittal with the 'approved stamp' of the Engineer shall be at the Contractor's own risk. Any design changes resulting in resizing pipe and/or revising hydraulic calculations will be done at no cost to the Owner. D. The working drawing submittals shall contain at least two (2) copies of reproducible sepias of piping layout and at least two (2) copies of hydraulic calculations. Calculations shall include peaking information for each area calculated. The hydraulic calculation used for the system design shall be clearly identified from all other hydraulic calculations and should show the safety factor the designed system has relevant to the available water test pressure. FIRE PROTECTION SYSTEM 21-3
6 E. Hydraulic calculations shall include: actual pipe internal diameters and coefficients of materials approved in the layout submittal; design density; remote area size; and area per sprinkler. F. The Contractor shall not pursue any approvals or interpretations of the design documents except through the office of the Architect/Engineer. G. All work shall meet the requirements of the Owner, authority having jurisdiction, Owner's insurance underwriter, Architect and Engineer. These requirements may be greater than required by NFPA. Work shall not start prior to the Contractor receiving the working drawing shop drawings with the 'stamp' of the Engineer and approval from the authority having jurisdiction TESTING A. Preliminary testing witnessed by the Architect/Engineer shall be conducted to assure proper operation before the final test is scheduled. Prior to this testing, pipes shall be flushed, hydrostatically tested, and all valves and devices shall be operated. All requirements of System Acceptance of NFPA 13 shall be met in full. B. The sprinkler system shall be final Acceptance tested in the presence of the Owner's Representative and the governing agencies having jurisdiction for approval ACCEPTANCE A..Acceptance test performed as described above. B. Contractor shall fill out completely and sign Contractor's Material and Test Certificate provided in NFPA-13 and submit to Engineer for approval and thus system acceptance SPACE CLASSIFICATION A. The most stringent of NFPA-13, local practices, or the following criteria shall be used in the sprinkler system design and hydraulic calculations. 1) Light Hazard: SERVICE ENTRANCE VALVES Offices Toilet Rooms Lobby/Commons Area Corridors Music Rooms Meeting Rooms Training Room Multi-Purpose Rooms Stairs A. All valves shall be UL listed or F.M. approved and rated for 175 psi and listed for use in fire protection systems. B. Zone valves shall be, flanged or groove-end, UL 262 OS&Y gate valve or UL 1091 butterfly valve with manual gear operator, position indicator, and integral tamper switch. FIRE PROTECTION SYSTEM 21-4
7 C. Drain valves shall be MSS SP-80, Type 2, Class 125 minimum, threaded or groove-end rising stem globe valve PIPING MATERIAL AND FITTING SCHEDULE A. Size: 2-1/2 and larger above grade. 1. Pipe: Schedule 10 Steel, listed lightweight steel, or Schedule 40 steel at the Contractor's option. 2. Fittings: Butt-welded, groove-end, forged steel flanged. 3. Joints: Butt welded, groove-end couplings, flanged. 4. Tests: Hydrostatically at not less than 200 psi for two (2) hours per NFPA 13, Section B. Size: 2 and smaller above grade. 1. Pipe: Schedule Fitting: Cast iron. 3. Joints: Screwed, groove-end. 4. Tests: Hydrostatically at not less than 200 psi for two (2) hours per NFPA 13, Section C. The following types of fittings are prohibited: plain end couplings and fittings, saddle tee, Victaulic flange rings, and Victaulic reducing couplings. D. Pipe velocities shall not exceed 14 feet per second in any section of the piping system WET PIPE SPRINKLER SYSTEM SPRINKLER HEADS A. All sprinkler heads are to be quick response liquid in glass bulb type, with a minimum of ½ inch orifice, ½ inch NPT, and a K factor of Sprinklers have an orifice larger than ½ inch shall be ¾ NPT. B. In finished spaces with ceilings, concealed sprinklers with an adjustable white coverplate shall be used. Heads shall be equivalent to the Viking model Horizon Mirage, Star model Stealth S110, Central model Royal Flush Concealed, or Reliable model G4QR. C. Temperature range and response time shall be suitable for the location and the expected heat release. Within a space all sprinklers should be the same Temperature Range and Response Time to avoid skipping. FIRE PROTECTION SYSTEM 21-5
8 AREAS SUBJECT TO FREEZING A. At locations which are subject to freezing and where permitted by the Authority having jurisdiction provide anti-freeze fill loop with all required specialties including, but not limited to, fill cup, test valves, drain valve, and backflow preventer. At locations which the above is not permitted provide a dry pipe system. END OF SECTION FIRE PROTECTION SYSTEM 21-6
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
SECTION 21 05 00 COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 - GENERAL 1.1 SUMMARY A. This section supplements all sections in this division, including pipe, fittings, valves, and connections for sprinkler
More informationSECTION BASIC FIRE SUPPRESSION MATERIALS AND METHODS. A. Section includes pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - BASIC FIRE SUPPRESSION MATERIALS AND METHODS PART 1 GENERAL 1.1 SUMMARY A. Section includes pipe, fittings, valves, and connections for sprinkler systems. B. Related Sections: 1. Section
More informationSECTION WET-PIPE SPRINKLER SYSTEMS
SECTION 21 13 13 WET-PIPE SPRINKLER SYSTEMS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GENERAL-DUTY VALVES FOR WATER-BASED FIRE-SUPPRESSION PIPING
PART 1 GENERAL SECTION 21 0523 GENERAL-DUTY VALVES FOR 1.01 SECTION INCLUDES A. Two-piece ball valves with indicators. B. Bronze butterfly valves with indicators. C. Iron butterfly valves with indicators.
More informationCHINO VALLEY FIRE DISTRICT FIRE PROTECTION STANDARD
CHINO VALLEY FIRE DISTRICT FIRE PROTECTION STANDARD SPECIFICATIONS Establishing Minimum Standards for as Related To Fire Protection STANDARD # 103 REVISED 04/01/19 PAGES 7 SCOPE: These specifications shall
More informationSECTION FIRE SPRINKLER NARRATIVE PART 1 - GENERAL INTRODUCTION
SECTION 210000 FIRE SPRINKLER NARRATIVE PART 1 - GENERAL INTRODUCTION Section includes: The purpose of this section is to define the design approach upon which the Fire Sprinkler contractor is to base
More informationSOLICITATION ADDENDUM NO. 1 RFP THE FOLLOWING CHANGES TO THE ABOVE CITED SOLICITATION ARE ANNOUNCED.
Beaverton School District Capital Program Purchasing 16550 SW Merlo Road, Beaverton, OR 97006 Phone: 503-591-4539 SOLICITATION ADDENDUM NO. 1 RFP 15-0013 THE FOLLOWING CHANGES TO THE ABOVE CITED SOLICITATION
More informationF International Fire Code
210500- COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 -GENERAL REQUIREMENTS AND EXECUTION REQUIREMENTS 1.1 CODE SECTIONS A. 2012 International Mechanical Code B. 20121nternational Building Code C. 2012
More informationEast Central College
SECTION 221116 - DOMESTIC WATER PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPERMIT SUBMITTAL GUIDE FOR COMMERCIAL PROJECTS
Collier Township 2418 Hilltop Road, Suite 100, Presto, PA 15142 Ph. 412-279-9998 PERMIT SUBMITTAL GUIDE FOR COMMERCIAL PROJECTS This guide applies to all projects except 1 & 2 family dwellings and townhouses
More informationCertificate of Compliance. Automatic Control Mode Sprinklers for Fire Protection
Page 1 of 1 Certificate Number Report Reference Issue Date Issued to: This is to certify that representative samples of Standard(s) for Safety: Additional Information: Only those products bearing the UL
More informationCOMMON WORK RESULTS FOR FIRE SUPPRESSION
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 - GENERAL 1 RELATED DOCUMENTS: A. Refer to Section 23 05 00. All work of Division 21 shall be in accordance with the corresponding section
More informationMICROFAST COIN TM QUICK RESPONSE UPRIGHT SPRINKLER SIN VK900 (SPECIFIC APPLICATION) TECHNICAL DATA
February 2, 2007 Sprinkler 112a Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. DESCRIPTION Viking Microfast QR COIN TM Sprinklers are quick
More informationCOIN QUICK RESPONSE UPRIGHT SPRINKLER VK900 (SPECIFIC APPLICATION) TECHNICAL DATA
1. DESCRIPTION Viking QR COIN Sprinklers are quick response specific application sprinklers for combustible interstitial (concealed) spaces (i.e., between floors, as well as low pitch attics that meet
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
Page 210500-1 SECTION 210500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information3. technical data. Page 1 of 10
Page of 0. DESCRIPTION Viking Quick Response Ordinary Hazard Dry Horizontal Sidewall Sprinklers are thermosensitive spray sprinklers suitable for use in areas subject to freezing. The sprinklers are designed
More information40.09 V25, K4.2 FIRE PROTECTION PRODUCTS AUTOMATIC SPRINKLERS SPECIFIC APPLICATION V2502 UPRIGHT QUICK RESPONSE
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic Model V2502 Specific Application Sprinklers are quick-response, specific application sprinklers for horizontal, combustible interstitial (concealed)
More informationTECHNICAL DATA COIN QUICK RESPONSE UPRIGHT SPRINKLER VK950 (SPECIFIC APPLICATION)
1 of 11 1. DESCRIPTION Viking QR COIN Sprinklers are quick response specific application sprinklers for combustible interstitial (concealed) spaces (i.e., between floors, as well as low pitch attics that
More informationRISER DETAIL NTS SHANNON FIRE PROTECTION, LLC SCALE: 3/32" = 1'-0"
MAXIMUM DISTANCE BETWEEN HANGERS NOMINAL PIPE SIZE (in.) 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 5" 6" 8" STEEL PIPE EXCEPT THREADED LIGHTWALL THREADED LIGHTWALL STEEL PIPE COPPER TUBE 10-0 10-0 CPVC
More informationHOT, CHILLED, AND CONDENSING WATER PIPING SPECIALTIES (HVAC)
SECTION 15432 HOT, CHILLED, AND CONDENSING WATER PIPING SPECIALTIES (HVAC) PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15047 - Identification. 2. 15433 - HVAC Pumps. 3. 15555 - Horizontal Fire
More informationGas Station & C Store SECTION CWM Job No
SECTION 211010 - PART 1 - GENERAL 1.1 WORK INCLUDED A. Provide labor, materials, equipment and services to perform operations required for the complete installation and related Work as required in Contract
More informationUniversity of Central Florida Main Campus. Domestic Water. Service and Meter Installations Requirements. Issued January 26 th, 2017.
University of Central Florida Main Campus Domestic Water Service and Meter Installations Requirements Issued January 26 th, 2017 1 P a g e Table of Contents 1. GENERAL INFORMATION... 3 2. DEFINITIONS...
More informationA. ASTM F Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems.
SECTION 221114 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the water distribution piping system, including potable cold, hot and hot water piping including associated fittings, and specialities
More informationCity of Winnipeg BASES, HANGERS AND SUPPORTS Section NEWPCC - Pump Well Isolation Page 1 of 6 Tender No June 2003
NEWPCC - Pump Well Isolation Page 1 of 6 PART 1 General 1.1 RELATED SECTIONS.1 Section 01001 General Requirements..2 Section 03300 - Cast-in-Place Concrete..3 Section 05121 - Structural Steel for Buildings..4
More informationADDENDUM NUMBER 1 PARTICULARS 1.01 DATE: APRIL 6, 2018
PARTICULARS 1.01 DATE: APRIL 6, 2018 ADDENDUM NUMBER 1 1.02 PROJECT: MIDLANDS TECHNICAL COLLEGE NE CAMPUS - CET CHILLER REPLACEMENT 1.03 OWNER'S PROJECT NUMBER: H59-N991-FW 1.04 ENGINEER: GMK ASSOCIATES
More informationCity Of Mendota Construction Procedures
City Of Mendota Construction Procedures Building Permit Application: A permit shall be obtained prior to commencing work of any type. Failure to do so may result in doubling the permit fees. At the time
More informationA. Codes and Standards that are Standard at the University: 1. AGA Compliance: LC 1-91 Interior Fuel Gas Piping Systems
PART 1: GENERAL 1.01 Purpose: This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is to
More informationPLUMBING. 1. New kitchen sinks and vanity sinks in residential units; new accessible showers and tubs in residential units and public showers.
SECTION 220500 PLUMBING 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.
More informationCOMMERCIAL TENANT IMPROVEMENT PERMIT APPLICATION
COMMERCIAL TENANT IMPROVEMENT PERMIT APPLICATION OFFICIAL USE ONLY Date: Permit #: Received by: For Staff Use Only: OFD ELEC Planning SITE LOCATION Site Address: Tax Parcel Number: TYPE OF WORK Building
More informationDIVISION 15-MECHANICAL SECTION SUPPORTS AND ANCHORS PN PART 1 - GENERAL 1.01 SECTION INCLUDES. A. Pipe and equipment support systems.
PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and equipment support systems. B. Inserts. 1.02 RELATED SECTIONS A. Section 15890 - Ductwork Supports. 1.03 DEFINITIONS A. Supports: Attachments, hangers,
More informationThis specification describes the minimum requirements for piping systems for the following service:
1.0 APPLICATION 1/8 This specification describes the minimum requirements for piping systems for the following service: Gland Water Design Condition Operating Conditions 50 PSIG @ 150 F 0 to 5 PSIG @ 35
More informationGUC LNG Facility Phase IIB Expansion 6/20/14 INSTRUMENTATION SPECIFICATION. A. This Section includes instrumentation for process piping systems.
INSTRUMENTATION SPECIFICATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS
SECTION 02620 PART 1 GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment, and incidentals required to install High Density Polyethylene (HDPE) pressure pipe, fittings, and appurtenances
More informationBuilding Permit Application
Building Permit Application Administrative Use Only PARENT PERMIT NUMBER (Required if part of another project) PERMITTEE: PERMITTEE ADDRESS: E-MAIL ADDRESS: ARCHITECT/ENGINEER: ARCHITECT/ENGINEER ADDRESS:
More informationCity of Westerville Guide to Commercial Inspections
City of Westerville Guide to Commercial Inspections FOOTINGS - After the excavation, with the form work and any required reinforcing steel in place. All footings shall have loose soil removed, reinforcing
More informationSECTION TAPPING SLEEVES AND VALVES
SECTION 33 12 16.17 TAPPING SLEEVES AND VALVES PART 1: GENERAL 1.01 SCOPE Furnish, install and test all tapping sleeves, tapping valves, and tapping saddles as shown on the Drawings. 1.02 RELATED WORK
More informationUnderground Piping for Private Hydrants & Sprinkler Supply Line
City of Brea Brea Fire Department Fire Prevention 1 Civic Center Circle Phone: (714) 990-7655 Underground Piping for Private Hydrants & Sprinkler Supply Line PURPOSE The provision of adequate water supplies
More informationA. Piping materials shall bear label, stamp, or other markings of specified testing agency.
SECTION 221316- PART 1- GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe, tube, and fittings. 2. Specialty pipe fittings. 1.2 INFORMATIONAL SUBMITTALS A. Field quality-control reports. 1.3 QUALITY ASSURANCE
More informationSECTION (15194) - FACILITY NATURAL-GAS PIPING
PART 1 GENERAL 1.01 SUMMARY SECTION 23 11 23 (15194) - FACILITY NATURAL-GAS PIPING A. Section Includes: 1. Pipe, Fittings and Joining Materials. 2. Protective Coating. 3. Piping Specialties. 4. Valves.
More informationTECHNICAL DATA OBSOLETE
October 14, 2005 Sprinkler 112 h For Light-Hazard Occupancies only. 1. PRODUCT NAME Viking Microfast QR COIN TM Combustible Interstitial Space Upright Fusible Element Sprinkler SIN VK901 (Specific Application)
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 15510 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More informationSECTION CROSS CONNECTION CONTROL AND BACKFLOW PREVENTION
SECTION 22 11 16.13 CROSS CONNECTION CONTROL AND BACKFLOW PREVENTION PART 1: GENERAL 1.01 SUMMARY A. This Section includes water-distribution backflow prevention products and installation specifications.
More informationBus Facility
SECTION 32 31 13.53 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationStainless Steel Aeration Equipment Specification
Section 15 Stainless Steel Aeration Equipment Specification Part 1 - General 1.01 Description A. Scope of Work 1. Furnish, install and test aeration system including air mains, drop pipes, valves, expansion
More informationCOIN QR UPRIGHT FUSIBLE ELEMENT SPRINKLER VK901 (SPECIFIC APPLICATION) TECHNICAL DATA
1 of 9 1. DESCRIPTION Viking QR COIN Sprinklers are quick response specific application sprinklers for combustible interstitial (concealed) spaces (i.e., between floors, as well as low pitch attics that
More informationC. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTexas Tech University Health Sciences Campus - MSBII Supplemental Bid Instructions March 3, 2017
Texas Tech University Health Sciences Campus - MSBII Supplemental Bid Instructions March 3, 2017 Automatic Fire Suppression - 210000 Without limiting the application of all of the Contract Documents to
More information1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME).
Issued 2005/06/01 Section 15112 Valves Cast Iron, Gate, Globe, Check Page 1 of 8 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300 C. ANSI/ASME
More informationSECTION GROUND STORAGE TANK
SECTION 13210 GROUND STORAGE TANK PART 1 GENERAL 1.01 Summary A. Section Includes: Provision for welded steel storage tank design, fabrication, construction and erection, including tank accessories. B.
More informationSECTION STANDPIPE AND HOSE SYSTEMS
SECTION 15375 STANDPIPE AND HOSE SYSTEMS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: A complete fire protection standpipe system including necessary accessories as indicated on Construction Documents,
More information1. Required Minimum Flow:
SECTION 6 6. 6.01 General The City of Castle Rock Water System Minimum Standards and Specifications are minimum base level performance, design, and construction standards used to maintain uniformity of
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 1316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSection 12 Hydraulics.
Design Guidelines Section 12 Hydraulics. www.canterbury.ac.nz/learningresources Standards in the Design Guidelines Suite Design Standard Guidelines Index: 01 General 02 Architecture 03 Audio Visual 04
More informationPART VII - WATER SYSTEM DESIGN CRITERIA
PART VII - WATER SYSTEM DESIGN CRITERIA A. Water Distribution, General 1. The water system layout shall be approved by the City Engineer. The fire hydrant layout shall be approved by the Redwood City Fire
More informationSECTION PUBLIC WATER SERVICE CONNECTIONS
SECTION 33 14 14 PUBLIC WATER SERVICE CONNECTIONS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe and fittings for water service connections to small commercial, light industrial, and residential
More informationDIVISION 15- MECHANICAL Section Fire Pumps
DIVISION 15- MECHANICAL Section 15320 Fire Pumps 1.00 PART 1 -GENERAL 1.01 DESCRIPTION OF WORK: A. Provide pumps for fire suppression. 1.02 SECTION INCLUDES: A. Vertical Turbine Fire Pump RELATED DOCUMENTS:
More informationEngineering Specifications
PROPRESS WITH SMART CONNECT FEATURE PART 1: GENERAL 1.1 SUMMARY A. Copper Tubing and Fitting System for Hot and Cold Water Distribution Systems, Sprinkler and Standpipe Systems and Hydronic Piping Systems
More informationEngineering Specifications
PROPRESS WITH SMART CONNECT FEATURE PART 1: GENERAL 1.1 SUMMARY A. Copper Tubing and Fitting System for Hot and Cold Water Distribution Systems, Sprinkler and Standpipe Systems and Hydronic Piping Systems
More informationLABORATORY & DEIONIZED WATER SYSTEMS DESIGN AND CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Purpose A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationSECTION (15194) - FACILITY NATURAL-GAS PIPING
SECTION 23 11 23 (15194) - FACILITY NATURAL-GAS PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Pipe, Fittings and Joining Materials. 2. Protective Coating. 3. Piping Specialties. 4. Valves.
More informationº to 150º F In accordance with this specification and
SPEC-3006 2016/0/18 1/10 1.0 PURPOSE This specification describes the minimum requirements gland water piping systems operating at or below 400 PSIG. Gland water systems are to be constructed either of
More informationBid Opportunity PLUMBING SYSTEMS Section Installation of Boiler Heating Systems Page 1 of 7 Centennial Pool, 90 Sinclair
Installation of Boiler Heating Systems Page 1 of 7 SECTION PAGE PART 1 GENERAL 2 1.1 General 2 1.2 Reference 2 1.3 Work Included 2 1.4 Related Work Specified Elsewhere 2 PART 2 PRODUCTS 3 2.1 Pipe and
More informationEast Central College HANSEN HALL LEVEL 300/400 RENOVATIONS CONSTRUCTION PACKAGE
SECTION 220529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More information1DIVISION 15- MECHANICAL Section Fire Pumps. A. Single Stage, Double Suction, 9100 Series Horizontal Splitcase Fire Pump (Base Mounted)
1DIVISION 15- MECHANICAL Section 15320 Fire Pumps 1.00 PART 1 -GENERAL 1.01 DESCRIPTION OF WORK: A. Provide pumps for fire suppression. 1.02 SECTION INCLUDES: A. Single Stage, Double Suction, 9100 Series
More informationBNIM ARCHITECTS 2460 PERSHING ROAD, SUITE 100 KANSAS CITY, MO
Page 1 of 3 ADDENDUM #4 DATE: DECEMBER 12, 2017 TO CONTRACT DOCUMENTS ENTITLED: CP170621 SCHOOL OF MUSIC NEW BUILDING CP172801 - GENERAL SITE: SCHOOL OF MUSIC EXTENDED UTILITIES ADVERTISEMENT DATE: November
More information.1 ANSI/ASME B31.1, Power Piping, (SI Edition)..2 American Society for Testing and Materials (ASTM)
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 03300 - Cast-in-Place Concrete.2 Section 05121 - Structural Steel for Buildings.3 Section 05500 - Metal Fabrications 1.2 REFERENCES.1
More informationSANITARY WASTE AND VENT PIPING
SECTION 15420 - SANITARY WASTE AND VENT PIPING PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationUniversity of Delaware
University Contact: Energy & Engineering Group (302) 831-1744 SECTION 22 67 00_PROCESS WATER PIPING SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. De-Ionized (DI) Water Systems 2. Distilled
More informationCity of Pekin- Zoning and Inspections Department 111 S. Capitol Street, Pekin, Illinois (309)
COMMERCIAL, INDUSTRIAL & MULTI-FAMILY RESIDENTIAL PROJECTS GENERAL INFORMATION The provisions of the International Building Code, 2006 Edition as amended by the City of Pekin adopting ordinance, shall
More informationSECTION The specification section is organized by placing information in three standard parts:
SECTION 14244 LIMITED USE HYDRAULIC ELEVATOR ***** Since 1982 Liftavator, Inc. has provided limited use/limited application (LU/LA) elevators, residential elevators, hydraulic vertical platform wheelchair
More informationEngineering Specifications
Zero Lead* ProPress Fitting System With Smart Connect Technology PART 1: GENERAL 1.1 SUMMARY A. Copper Tubing and Fitting System for Hot and Cold Water Distribution Systems, Sprinkler and Standpipe Systems
More informationSECTION FIRE HYDRANTS
SECTION 21 11 10 PART 1. GENERAL 1.1 SUMMARY: A. Work consists of furnishing and installing new fire hydrants, (boot with ductile iron retainer gland, standpipe and hydrant complete) plus constructing
More informationSECTION WATER DISTRIBUTION SYSTEM
Conditions of Use/ Responsibility of Data Montgomery County Public Schools Facilities Guide DIVISION 2 - SITE WORK These guideline specifications are to be used by the A/E as a base document in the development
More informationA. Product Data: For Piping, fittings, transition fittings and dielectric fittings.
SECTION 22 11 16 - DOMESTIC WATER PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 01 4000 - QUALITY REQUIREMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ASME BPVC Section IX - Welding and Brazing Qualifications B. ASME B16.3 - Malleable Iron Threaded Fittings Classes 150 and 300 C. ASME
More informationA. This Section includes the following sanitary drainage piping specialties:
Page 221319-1 SECTION 221319 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information1.2 ACTION AND INFORMATIONAL SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures.
BID OPPORTUNITY NO. 253-2011 PAGE 1 OF 7 PART 1 GENERAL 1.1 REFERENCES.1 American Society of Mechanical Engineers (ASME).1 ASME B31.1, Power Piping, B31.3 Process Piping, B31.9 Building Services Piping..2
More informationSECTION FIRE HYDRANTS
SECTION 02080 FIRE HYDRANTS PART 1 - GENERAL 1.01 DESCRIPTION A. Work Specified The work specified shall include all labor, material, equipment, tools, services and incidentals necessary to furnish and
More informationSECTION GENERAL ELECTRICAL REQUIREMENTS PART 1- GENERAL
1.01 DESCRIPTION SECTION 16000 GENERAL ELECTRICAL REQUIREMENTS PART 1- GENERAL A. This Section includes the general provisions applicable to electrical work and testing of the completed electrical systems.
More informationA. This Section includes sanitary waste and vent piping inside the building and to locations indicated.
SECTION 221316 SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDesign and Construction Standards SECTION HYDRONIC PIPING
SECTION 15510 HYDRONIC PIPING PART 1 GENERAL 1.1 REFERENCES A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More informationSECTION LIGHTNING PROTECTION SYSTEM
SECTION 16670 - LIGHTNING PROTECTION SYSTEM PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSpecification Lightning Protection Systems
Specification Lightning Protection Systems General: Summary A) This Section specifies the lightning protection system for the building(s) or structure(s). This system provides safety for the building and
More informationORDINANCE NO. XXXX BE IT ORDAINED BY THE GOVERNING BODY OF THE CITY OF LAWRENCE, KANSAS:
ORDINANCE NO. XXXX AN ORDINANCE OF THE CITY OF LAWRENCE, KANSAS, REPEALING EXISTING CHAPTER 5, ARTICLE 6 OF THE CODE OF THE CITY OF LAWRENCE, 2018 EDITION, AND AMENDMENTS THERETO, AND ENACTING, IN ITS
More informationSECTION FACILITY STORM DRAINAGE PIPING
SECTION 22 1413 FACILITY STORM DRAINAGE PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationCity of Middletown WATER & SEWER DEPARTMENT 82 Berlin Street Middletown, CT TEL: (860) FAX: (860)
City of Middletown WATER & SEWER DEPARTMENT 82 Berlin Street Middletown, CT 06457 TEL: (860) 638-3500 FAX: (860) 343-8091 GENERAL REQUIREMENTS WATER MAIN AND SERVICE INSTALLATION JANUARY 2017 WATER MAINS:
More informationMODEL SPECIFICATIONS: Hydraulically Driven Steel Underpinning Pile Specifications
MODEL SPECIFICATIONS: Hydraulically Driven Steel Underpinning Pile Specifications Mar/2008 v1.0 SECTION 02255 HYDRAULICLY DRIVEN STEEL UNDERPINNING PILES PART 1 GENERAL 1.01 SCOPE OF WORK The work shall
More informationUNIFORM DESIGN AND CONSTRUCTION STANDARDS FOR EXTENDING WATER DISTRIBUTION SYSTEMS SECTION 2 DESIGN STANDARDS
UNIFORM DESIGN AND CONSTRUCTION STANDARDS FOR EXTENDING WATER DISTRIBUTION SYSTEMS SECTION 2 DESIGN STANDARDS DESIGN STANDARDS SECTION 2 INDEX ITEM DESCRIPTION 2.00 GENERAL STATEMENT 2.01 WATER DISTRIBUTION
More informationDIVISION 22 PLUMBING SECTION INTERIOR SANITARY WASTE AND VENT PIPING SYSTEM
DIVISION 22 PLUMBING PART 1 GENERAL 1.01 DESCRIPTION A. Provide a complete system of soil, waste, and vent piping to fixtures and equipment, including traps, floor drains and cleanouts, extending to a
More informationSECTION SEISMIC RESTRAINT REQUIREMENTS FOR NON-STRUCTURAL COMPONENTS REVISED PART 1 GENERAL 1.1 DESCRIPTION:
SECTION 13 05 41 SEISMIC RESTRAINT REQUIREMENTS FOR NON-STRUCTURAL COMPONENTS REVISED 1-25-13 PART 1 GENERAL 1.1 DESCRIPTION: A. Provide seismic restraint in accordance with the requirements of this section
More informationSECTION PLUMBING PIPING SYSTEMS
SECTION 15300 PLUMBING PIPING SYSTEMS PART 1 - GENERAL 1.01 SPECIAL NOTICE A. Each contractor shall read all relevant documents, become familiar with the job, the scope of work, type of general construction,
More informationB. Refer to Division 31 Section "Earth Moving for excavating, trenching, and backfilling.
This specification is neither project nor code-specific. It is the responsibility of the contracted Design Professional to produce Contract Documents in conformance with the approved Scope of Work and
More informationSECTION 401 WATER PIPE AND FITTINGS 2.2 POLYVINYL CHLORIDE (PVC) PIPE AND FITTINGS
SECTION 401 PIPE AND FITTINGS PART 2 MATERIALS 2.2 POLYVINYL CHLORIDE (PVC) PIPE AND FITTINGS A. PVC Pressure Pipe sizes 4 inch through 12 inch: ANSI/AWWA C 900 1. DR18 B. PVC Pressure Pipe sizes 14 inch
More informationCode. 1) Code. Standard or Specification. Bolting
Code 1. Code 1) Code (1) ASME B 31.1 : Power Piping (2) ASME B 31.3 : Process Piping (3) ASME B 31.4 : Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids 2) Material Code Bolting
More informationEos Common Steel Piping Database for Sage Timberline Office Estimating
for Sage Timberline Office Estimating Introduction The Common Steel Piping Database for Sage Timberline Office Estimating is designed to support piping estimating for buildings, process facilities, power
More informationB. American Society for Testing and Materials: 1. ASTM F708 - Standard Practice for Design and Installation of Rigid Pipe Hangers.
SECTION 230529 - HANGERS AND SUPPORTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Sleeves. 6. Mechanical sleeve seals. 7. Firestopping
More informationFirst Revision No. 634-NFPA [ Global Input ] Supplemental Information. Submitter Information Verification. Committee Statement
National Fire Protection Association Report http://submittals.nfpa.org/terraviewweb/contentfetcher?commentpara... 5 of 398 11/14/2016 10:55 AM First Revision No. 634-NFPA 13-2016 [ Global Input ] See attached
More information