SECTION STANDPIPE AND HOSE SYSTEMS
|
|
- Beverly Johnson
- 5 years ago
- Views:
Transcription
1 SECTION STANDPIPE AND HOSE SYSTEMS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: A complete fire protection standpipe system including necessary accessories as indicated on Construction Documents, specified in this section, and as required by NFPA 14. B. Related Sections: Firestopping and Fire and Smoke Barrier Caulking Fire Protection Fire Pump and Controls Automatic Sprinkler Systems Fire Alarm and Detection Systems REFERENCES A. American Society for Testing and Materials (ASTM): 1. A53-96 Specification for Pipe, Steel, Black and Hot- Dipped, Zinc-Coated, Welded and Seamless SUBMITTALS A. Submit properly identified manufacturer's literature before starting work. B. Submit Shop Drawings on the following: 1. Valves and appurtenances: Catalog cuts 2. Pipe hangers and supports: Catalog cuts 3. Piping: Manufacturer's name and mill reports C. Detailed drawings of proposed departures due to actual field conditions or other causes shall be submitted to the A/E QUALITY ASSURANCE Project No. SPECIFICATION GUIDELINES
2 A. Fire protection equipment and devices shall be listed by Underwriters Laboratories for service intended. Equipment shall be installed in conformance with standards of National Fire Protection Association (NFPA) and Factory Mutual (FM). B. Electrical installation shall comply with the National Electrical Code (NEC) PROJECT CONDITIONS A. Coordination of Drawings: Because of small scale of Construction Documents, it is not possible to indicate all required offsets, fittings and accessories. Contractor shall carefully investigate structure and all other trades involved including finish conditions affecting all his work and shall arrange such work accordingly, furnishing such fittings, valves, and accessories as may be required to meet such conditions, at no additional cost to the Board. PART 2 PRODUCTS 2.01 MATERIALS A. Piping: ASTM A53 seamless. Schedule 40 threaded black steel pipe. B. Fittings: 1. Threaded malleable iron or screwed banded cast iron. ANSI B16.4 and B Inches and Larger: Cast iron or steel flanged fittings, ANSI B16.5; Victualic style 77 couplings with Grade H gaskets. 3. Welded Fittings: ANSI B C. Valves and Appurtenances: 1. Gate Valves: a. 2-1/2" and larger Crane #467, Stockham G-634; or Jenkins 825-A. UL listed, flanged faced, outside screw and yoke, ferro-steel body and bonnet and Project No. SPECIFICATION GUIDELINES
3 bronze fitted, 175 WWP Class. b. 2 Inches and Smaller: OS & Y threaded bronze, rising step 175 WWP Class; Walworth 13, Stockham B- 133, Jenkins Check Valves: a. 2-1/2" and Larger: Crane #375, Stockham G939 or Jenkins 629. UL approved ferro steel body with bronze or iron disc and seat, 175 WWP Class. b. 2 Inches and Smaller: Threaded bronze swing type, 175 WWP Class; Walworth 406, Stockham B319, Jenkins 92A. c. Silent Type: Flanged cast iron or steel body, bronze trim, double center guided spring, 175 psi wog. 1) 2 Inches and Smaller: Threaded end; Mueller 203-AP, Williams Gauge Co. 2) 2-1/2" and Larger: Flanged end; Mueller 105-AP, Williams Gauge Co. 3. Globe Valves: Bronze body and disc, screwed bonnet, 200 psi wog, threaded ends. Stockham No.B-16, Crane No.1, Jenkins No Hose Valves and Racks: Potter Roemer Series 1200 with 2-1/2" valve, enamel rack, 2-1/2" x 1-1/2" reducing coupling, 1-1/2" linen hose and brass fog nozzle. 5. Post Indicator Valves: Iron body, bronze mounted, flanged, non-rising stem, solid wedge disc with vertical indicator post. Stockham valve No.G with G95 indicator or Kennedy Fig.701 valve with Fig.541 indicator. 6. Siamese Connection: Potter-Roemer or accepted equivalent No.5763D cast brass free standing plugs and chains, polished chrome plated, 6 inches x 2-1/2" x 2-1/2". Stamp "Fire Sprinklers". 7. Roof Manifolds: Roof type, Potter-Roemer or accepted equivalent Series 5875, angle inlet, cast brass, twoway. Use Potter-Roemer Series 4065, cast brass, 2-1/2" valves with cap and chains. Provide salt-air resistant gage at top of riser. D. Hangers and Supports: Project No. SPECIFICATION GUIDELINES
4 1. Provide adjustable hangers as required for proper support of pipelines, according to NFPA 13. Hangers shall allow for expansion and contraction of pipelines. Hangers shall be wrought iron clevis type. 2. Piping supported from concrete slabs: Use hangers attached to rods suspended from concrete inserts. Powder actuated fasteners and devices are not allowed. "Redhead" self-drilling concrete expansion anchors are acceptable. 3. Single Pipe Runs: Support with adjustable swivel ring hangers. 4. Piping Supported from Walls or Columns: Use welded steel brackets, and adjustable swivel ring hanger. 5. Piping supported from steel structure: a. Extension C-clamp - Fig.83 b. Bar joist clip - Fig Standpipes supported from walls: Wrought strap - Fig Size of Pipe Hanging Rods Rod Diameter Up to 2 inch size pipe 3/8" 2-1/2" to 3-1/2" size pipe 1/2" 4 inch to 8 inch size pipe 3/4" E. Hose Cabinet: Furnish and install Allenco Hozeguard or accepted equivalent Hose Cabinet Model No.7169W having 12 gage door and trim, 16 gage tub, Style "D" steel door and trim. Cabinet equipped with 2-1/2 inch valve, 100 feet of unlined linen hose and couplings. Adjustable spray shut-off nozzle No Add pressure reducing valve when pressure exceeds 100 psi. For extinguisher in cabinet, see extinguisher specification, Section F. Fire Department Valve Cabinet: Allenco or accepted equivalent 282 series, 16 gage steel body and 20 gage door of hollow welded construction. Semi-concealed hinge and semi-recessed cam action latch. Baked white enameled finish inside with white prime coat outside. Cabinet capable of accommodating 2-1/2" with 1-1/2" capped reducer chained valve and 1 fire extinguisher. G. Joint Compound: White Tite Seal Project No. SPECIFICATION GUIDELINES
5 H. Materials installed in fire standpipe system shall be suitable for pressures and temperatures encountered. Installation shall be as required by NFPA 14 and as specified. PART 3 EXECUTION 3.01 INSTALLATION A. Standpipe System: 1. Cutting and Repairing: The work shall be carefully laid out in advance, and no excessive cutting of construction will be allowed. Damage to buildings, piping, wiring, or equipment because of cutting for installation shall be repaired by mechanics skilled in the trade involved at no additional expense to the Board. 2. Protection to Materials and Equipment: Pipe openings shall be closed with caps or plugs during installation. Fixtures and equipment shall be tightly covered and protected against dirt, water and chemical or mechanical injury. Upon completion of work, materials and equipment shall be thoroughly cleaned, adjusted and operated. B. Piping Joints and Methods of Connection: Steel threaded pipe after cutting and before threading: Ream pipe and remove burrs. Make screw joints of lines absolutely tight with joint compound brush applied to male threads only. After installation, exposed threads shall be painted as specified in Section Painting. C. Escutcheons: Fit and firmly secure escutcheons to pipes passing through finished floors, ceilings and walls, escutcheons of sufficient outside diameter to cover sleeved openings and set in fire retardant mastic. D. Piping: 1. Run piping enclosed where possible in wall chases, recesses, pipe shafts, wall partitions, and ceilings where provided. 2. Use reducing fittings for changes in pipe size. Project No. SPECIFICATION GUIDELINES
6 Bushings are not allowed. 3. Use extra heavy pipe for nipples where unthreaded portion is less than 1-1/2". Close nipples are not acceptable; use saddle nipples. E. Joints: 1. Make joints in screwed piping with acceptable compound on male threads only. Do not use lamp wick in joints. Threads shall be perfect, clean cut and of exactly proper length. Pipe shall be properly reamed after cutting and threading. 2. Make flanged joints with full face rubber gasket, or stainless steel. F. Hangers and Supports: 1. Properly support piping by accepted type hangers and supports: a. To secure piping in place. b. To prevent vibration. c. Of ample size to carry pipe. 2. Chain, straps, perforated bar, or wire hangers are not allowed. 3. Provide necessary supplemental steel for proper support or attachment of hangers. G. Sleeves: Provide sleeves large enough to accommodate pipes passing through floors, ceilings, walls, or partitions. 1. Penetrations by fire protection water lines through fire rated floors and walls shall be installed and firestopped using UL classified through penetration firestopping and fire and smoke barrier caulking as specified in Section 07270, Firestopping and Fire and Smoke Barrier Caulking. 2. The fire rating of the firestopping caulking shall be equivalent to or greater than the fire rating of the floor or wall penetrated. 3. Install firestopping and caulking according to with manufacturer's instructions. Project No. SPECIFICATION GUIDELINES
7 END OF SECTION Project No. SPECIFICATION GUIDELINES
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
SECTION 21 05 00 COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 - GENERAL 1.1 SUMMARY A. This section supplements all sections in this division, including pipe, fittings, valves, and connections for sprinkler
More informationSECTION BASIC FIRE SUPPRESSION MATERIALS AND METHODS. A. Section includes pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - BASIC FIRE SUPPRESSION MATERIALS AND METHODS PART 1 GENERAL 1.1 SUMMARY A. Section includes pipe, fittings, valves, and connections for sprinkler systems. B. Related Sections: 1. Section
More informationRESEARCH AND TECHNOLOGY BUILDING RENOVATION 05/18/09 SECTION DOMESTIC WATER PIPING SYSTEM
SECTION 22 11 00 DOMESTIC WATER PIPING SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Domestic water piping, above grade. 2. Unions and flanges. 3. Valves. 4. Pipe hangers and supports. 5. Backflow
More informationB. American Society for Testing and Materials: 1. ASTM F708 - Standard Practice for Design and Installation of Rigid Pipe Hangers.
SECTION 230529 - HANGERS AND SUPPORTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Sleeves. 6. Mechanical sleeve seals. 7. Firestopping
More informationGas Station & C Store SECTION CWM Job No
SECTION 211010 - PART 1 - GENERAL 1.1 WORK INCLUDED A. Provide labor, materials, equipment and services to perform operations required for the complete installation and related Work as required in Contract
More informationHOT, CHILLED, AND CONDENSING WATER PIPING SPECIALTIES (HVAC)
SECTION 15432 HOT, CHILLED, AND CONDENSING WATER PIPING SPECIALTIES (HVAC) PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15047 - Identification. 2. 15433 - HVAC Pumps. 3. 15555 - Horizontal Fire
More informationSECTION STEAM AND CONDENSATE HEATING PIPING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Pipe and pipe fittings. B. Pipe hangers and supports. C. Valves. D. Steam piping system. E. Steam condensate piping system. 1.02 RELATED REQUIREMENTS A. Section
More informationSECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes pipe and equipment supports, hangers, anchors, bases sleeves and the sealing of work
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT. A. ASME B31.1 (American Society of Mechanical Engineers) - Power Piping
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes pipe and equipment supports, hangers, anchors, bases sleeves and the sealing of
More informationNORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS
PART 1 GENERAL 1.01 SUMMARY Section 15140 PIPE HANGERS, This Section includes the furnishing and subsequent installation of: A. Pipe and equipment hangers, supports, and associated anchors B. Equipment
More informationPIPING SPECIALTIES (PLUMBING) A. American Society for Testing and Materials (ASTM):
SECTION 15430 PIPING SPECIALTIES (PLUMBING) PART 1 GENERAL 1.01 SUMMARY A. Related Section: 1. 15410 - Piping (Plumbing). 1.02 REFERENCES A. American Society for Testing and Materials (ASTM): 1. A126-95
More informationSUPPORT AND ANCHORS SECTION 15090
SUPPORT AND ANCHORS SECTION 15090 PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. Work included in this Section: Materials, equipment, fabrication, installation and tests in conformity with applicable codes
More informationDIVISION 15-MECHANICAL SECTION SUPPORTS AND ANCHORS PN PART 1 - GENERAL 1.01 SECTION INCLUDES. A. Pipe and equipment support systems.
PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and equipment support systems. B. Inserts. 1.02 RELATED SECTIONS A. Section 15890 - Ductwork Supports. 1.03 DEFINITIONS A. Supports: Attachments, hangers,
More informationSeptember 6, 2016 Page 1 of 5
September 6, 2016 Page 1 of 5 1. SECTION 16100 Drawing E4.3, Note #39: Reference to the radio fire alarm panel and the fire station alerting master panel does not relate to the building fire alarm system.
More informationA. Pipe Supports: ANSI B 31.1, Power Piping. B. Automatic Sprinkler Pipe Supports: Refer to Section
SECTION 15140 SUPPORTS, ANCHORS, AND SEALS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract including General and Supplementary Conditions, Division 1 Specification
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION PLUMBING PIPING
SECTION 22 1000 PLUMBING PIPING PART 1 GENERAL 1.1 QUALITY ASSURANCE A. Perform Work in accordance with authority having jurisdiction standards. Utilize products as indicated in drawings and as allowed
More informationELECTRICAL CONTRACTORS THE UNIVERSITY OF TENNESSEE KNOXVILLE, TENNESSEE SECTION PAGE 1 SECTION SUPPORTING DEVICES
KNOXVILLE, TENNESSEE SECTION 26 05 29 PAGE 1 PART 1 - GENERAL: 1.01 DESCRIPTION OF WORK: SECTION 26 05 29 A. Extent of supports, anchors, sleeves and seals is indicated by drawings and schedules and/or
More informationSECTION of GENERAL. A. Description
SECTION 15210-1 of 10 15210.01 GENERAL A. Description This section includes requirements for interior piping and fittings, buried and interior valves and specialty items used in conjunction with piping
More informationSECTION HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS
SECTION 26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and
More information1. Hangers and supports for electrical equipment and systems.
PART 1 - GENERAL... 1 1.1 RELATED DOCUMENTS... 1 1.2 SUMMARY... 1 1.3 DEFINITIONS... 1 1.4 PERFORMANCE REQUIREMENTS... 1 1.5 SUBMITTALS... 2 1.6 QUALITY ASSURANCE... 2 1.7 COORDINATION... 2 PART 2 - PRODUCTS...
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB #
SECTION 26 0529 - HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationSECTION RACEWAYS
SECTION 16110 RACEWAYS PART 1 GENERAL 1.1 SYSTEM DESCRIPTION A. Provide a complete raceway system suitable for receiving wire and cable and continuous from outlet to outlet. System shall be complete with
More informationHANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT SECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
13686.00 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT 230529-1 SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT 1.1 SUMMARY A. Section Includes: 1. Metal pipe hangers and supports.
More informationSECTION PLUMBING SYSTEMS
SECTION 15400 PLUMBING SYSTEMS PART 1 - GENERAL 1.1 DESCRIPTION Domestic water, sewer and fuel gas systems, including piping, equipment and all necessary accessories as designated in this section. 1.2
More informationPLUMBING. 1. New kitchen sinks and vanity sinks in residential units; new accessible showers and tubs in residential units and public showers.
SECTION 220500 PLUMBING 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.
More information1.2 ACTION AND INFORMATIONAL SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures.
BID OPPORTUNITY NO. 253-2011 PAGE 1 OF 7 PART 1 GENERAL 1.1 REFERENCES.1 American Society of Mechanical Engineers (ASME).1 ASME B31.1, Power Piping, B31.3 Process Piping, B31.9 Building Services Piping..2
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
Page 210500-1 SECTION 210500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationBASIC MATERIALS & METHODS
SECTION 15591 BASIC MATERIALS & METHODS 1. SCOPE 1.1 Work Included: 1. SCOPE... 1 2. PIPING SYSTEMS... 1 3. HWS/R PIPING SYSTEM... 2 4. GAS PIPING SYSTEMS... 5 5. PROTECTION OF EXISTING STRUCTURES AND
More informationDIVISION 26 RACEWAYS AND BOXES FOR ELECTRICAL SYSTEMS PART 1 - GENERAL RELATED DOCUMENTS
PART 1 - GENERAL 01.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification sections, apply to work of this Section.
More informationSECTION (Master Template Final-05) ELECTRICAL BOXES. A. Provide boxes for electrical equipment and wiring devices as follows:
SECTION 16130 (Master Template Final-05) ELECTRICAL BOXES PART 1 GENERAL 1.01 SECTION INCLUDES A. Provide boxes for electrical equipment and wiring devices as follows: 1. Wall and ceiling outlet boxes.
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION PLUMBING SPECIALTIES
SECTION 15430 PLUMBING SPECIALTIES PART 1 GENERAL The requirements of the GENERAL CONDITIONS, SUPPLEMENTARY CONDITIONS and Division 1, General Requirements, Apply to the work specified in this section.
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220529 - HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 DESCRIPTION A. The General Conditions, Special Conditions and Division 1 through Division 22 as set forth in
More informationOSU PROJECT NO PAGE 1 02 NOV 2006 SECTION SUPPORTS AND ANCHORS
OSU PROJECT NO. 30-04-15 PAGE 1 PART 1 GENERAL 1.1 WORK INCLUDED A. Supports and anchors for piping systems and equipment. 1.2 RELATED WORK SPECIFIED ELSEWHERE A. The provisions of Section 15050, Basic
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
Page 220529-1 SECTION 220529 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationADDENDUM NUMBER 1 PARTICULARS 1.01 DATE: APRIL 6, 2018
PARTICULARS 1.01 DATE: APRIL 6, 2018 ADDENDUM NUMBER 1 1.02 PROJECT: MIDLANDS TECHNICAL COLLEGE NE CAMPUS - CET CHILLER REPLACEMENT 1.03 OWNER'S PROJECT NUMBER: H59-N991-FW 1.04 ENGINEER: GMK ASSOCIATES
More information1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME).
Issued 2005/06/01 Section 15112 Valves Cast Iron, Gate, Globe, Check Page 1 of 8 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards
More informationSECTION (15194) - FACILITY NATURAL-GAS PIPING
PART 1 GENERAL 1.01 SUMMARY SECTION 23 11 23 (15194) - FACILITY NATURAL-GAS PIPING A. Section Includes: 1. Pipe, Fittings and Joining Materials. 2. Protective Coating. 3. Piping Specialties. 4. Valves.
More informationEast Central College HANSEN HALL LEVEL 300/400 RENOVATIONS CONSTRUCTION PACKAGE
SECTION 220529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationF International Fire Code
210500- COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 -GENERAL REQUIREMENTS AND EXECUTION REQUIREMENTS 1.1 CODE SECTIONS A. 2012 International Mechanical Code B. 20121nternational Building Code C. 2012
More information1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
More informationSECTION FACILITY STORM DRAINAGE
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 22 14 00 Storm drainage systems, including piping and all necessary accessories as designated in this section. 1.2 RELATED WORK A. Penetrations in rated enclosures:
More informationSECTION OUTLET, PULL, AND JUNCTION BOXES
SECTION 16131 OUTLET, PULL, AND JUNCTION BOXES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09900 - Painting. 2. 16112 - Raceways and Conduits. 1.02 SYSTEM DESCRIPTION A. Performance Requirements:
More informationDesign and Construction Standards SECTION HYDRONIC PIPING
SECTION 15510 HYDRONIC PIPING PART 1 GENERAL 1.1 REFERENCES A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220529 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationUniversity of Delaware
SECTION 22 05 01_COMMON REQUIREMENTS FOR PLUMBING SYSTEMS University Contact: Energy & Engineering Group (302) 831-1744 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pre-fabricated Pipe and Duct Supports
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 15510 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More informationSECTION STORM DRAINAGE PIPING SPECIALTIES PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 22 14 23 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300 C. ANSI/ASME
More informationSECTION HANDRAILS AND RAILINGS. A. Section Metal Fabrications: Associated metal supports.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Handrails and guardrails B. Guardrails for hatches and openings. C. Safety barriers. D. Roof edge protection. 1.2 RELATED SECTIONS
More information. SECTION HANGERS AND SUPPORTS
. SECTION 230529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division I Specification
More informationC. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 23 0529 - MECHANICAL SUPPORTING DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationDIVISION 5 - STRUCTURAL STEEL AND IRON WORK
DIVISION 5 - STRUCTURAL STEEL AND IRON WORK SECTION 05100 STRUCTURAL METAL FRAMING PART 1.00 GENERAL 1.01 SCOPE OF WORK A. Work Included: 1. 2. Structural steel complete in place. Steel joists complete
More informationSECTION (16071) - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 26 05 48 (16071) - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.01 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ASME BPVC Section IX - Welding and Brazing Qualifications B. ASME B16.3 - Malleable Iron Threaded Fittings Classes 150 and 300 C. ASME
More informationH D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS SECTION FB TOILET PARTITIONS
3501 East La Palma Avenue - Anaheim, California 92806 PART 1 GENERAL Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com H D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS 1.1 RELATED DOCUMENTS:
More informationSECTION HANGERS AND SUPPORTS PART 1 - GENERAL. A. Drawings and Division 1 Specification Sections, apply to this Section.
1.01 RELATED DOCUMENTS SECTION 15060 HANGERS AND SUPPORTS PART 1 - GENERAL A. Drawings and Division 1 Specification Sections, apply to this Section. 1.02 SUMMARY A. This Section includes hangers and supports
More informationKaf-Tech Product Specification
Kaf-Tech Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519.13 METAL CLAD CABLE-LUMINARY CABLE
More informationDaytona Beach Pier Building Renovation Jun 2010
SECTION 15060 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 1316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION FACILITY NATURAL-GAS PIPING
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 23 1123 FACILITY NATURAL-GAS A. Pipe, pipe fittings, valves, and connections for natural gas piping systems. 1.02 RELATED REQUIREMENTS A. Section 07 8400 -
More informationSECTION COMPOSITE METAL DECKING
PART 1 GENERAL 1.1 DESCRIPTION: SECTION 05 36 00 COMPOSITE METAL DECKING SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION VALVES, HANGERS, AND SPECIALTIES
SECTION 15515 VALVES, HANGERS, AND SPECIALTIES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15090 - Supports, Anchors, and Seals. 2. 15410 - Piping (Plumbing). 3. 15510 - Piping (HVAC). 4. 15540
More informationSECTION (15194) - FACILITY NATURAL-GAS PIPING
SECTION 23 11 23 (15194) - FACILITY NATURAL-GAS PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Pipe, Fittings and Joining Materials. 2. Protective Coating. 3. Piping Specialties. 4. Valves.
More informationHOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL
13686.00 HOLLOW METAL DOORS AND FRAMES 081113-1 SECTION 081113 - HOLLOW METAL DOORS AND FRAMES 1.1 RELATED DOCUMENTS: PART 1 - GENERAL A. Drawings and general provisions of Contract, including General
More informationCITY OF MOUNT DORA LIFT STATION CHAINLINK FENCE AND GATE SPECIFICATIONS
CITY OF MOUNT DORA LIFT STATION CHAINLINK FENCE AND GATE SPECIFICATIONS PART 1 - GENERAL 1.01 SUMMARY A. Section Includes furnishing and installing chain-link fabric fence, gate, and appurtenances. 1.02
More informationSECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 230529 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 230529 - HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of Contract, including General Conditions and other Division 1 Specification Sections,
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 22 0529 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationCity of Winnipeg BASES, HANGERS AND SUPPORTS Section NEWPCC - Pump Well Isolation Page 1 of 6 Tender No June 2003
NEWPCC - Pump Well Isolation Page 1 of 6 PART 1 General 1.1 RELATED SECTIONS.1 Section 01001 General Requirements..2 Section 03300 - Cast-in-Place Concrete..3 Section 05121 - Structural Steel for Buildings..4
More informationCHINO VALLEY FIRE DISTRICT FIRE PROTECTION STANDARD
CHINO VALLEY FIRE DISTRICT FIRE PROTECTION STANDARD SPECIFICATIONS Establishing Minimum Standards for as Related To Fire Protection STANDARD # 103 REVISED 04/01/19 PAGES 7 SCOPE: These specifications shall
More informationPART 2 SECTION 9 WATERLINES
PART 2 SECTION 9 WATERLINES 9-1 General - All pipe, pipeline installations and facilities related thereto, shall be as specified herein. All pipe installation shall be in accordance with the manufacturers
More informationSECTION WET-PIPE SPRINKLER SYSTEMS
SECTION 21 13 13 WET-PIPE SPRINKLER SYSTEMS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220529 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationBid Opportunity PLUMBING SYSTEMS Section Installation of Boiler Heating Systems Page 1 of 7 Centennial Pool, 90 Sinclair
Installation of Boiler Heating Systems Page 1 of 7 SECTION PAGE PART 1 GENERAL 2 1.1 General 2 1.2 Reference 2 1.3 Work Included 2 1.4 Related Work Specified Elsewhere 2 PART 2 PRODUCTS 3 2.1 Pipe and
More informationSECTION DUCTS PART 1 GENERAL 1.01 SUMMARY
1 1 1 1 1 1 1 1 0 1 0 1 SECTION 1 DUCTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Duct Materials.. Insulated flexible ducts.. Single wall spiral round ducts.. Ductwork fabrication.. Duct cleaning.
More information***************************************************************************************************************
09510 ACOUSTICAL CEILINGS SPECIFIER: CSI MasterFormat 2004 number 09 51 00 PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310
More informationSECTION COMPOSITE METAL DECKING
PART 1 GENERAL 1.1 DESCRIPTION SECTION 05 36 00 1. Use this section only for NCA projects. 2. Delete between // ---- // if not applicable to project. Also delete any other item or paragraph not applicable
More informationIron Check Valves & Y-Strainers Illustrated Index
Iron Check Valves & Y-Strainers Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Lead
More informationGate City Elementary HVAC Table of Contents Division 22 /1
DIVISION 22: PLUMBING 22 0000 PLUMBING 22 0501 COMMON PLUMBING REQUIREMENTS 22 0502 DEMOLITION AND REPAIR 22 0503 PIPE, PIPE FITTINGS, PIPE HANGERS & VALVES 22 0710 POTABLE WATER PIPE INSULATION 22 0800
More information.1 ANSI/ASME B31.1, Power Piping, (SI Edition)..2 American Society for Testing and Materials (ASTM)
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 03300 - Cast-in-Place Concrete.2 Section 05121 - Structural Steel for Buildings.3 Section 05500 - Metal Fabrications 1.2 REFERENCES.1
More informationSECTION ACCORDION FOLDING PARTITIONS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION CONDUITS AND BOXES PART 1- GENERAL. A. Work covered by this section includes the furnishing and installation of conduits and boxes.
SECTION 16111 CONDUITS AND BOXES 1.01 DESCRIPTION PART 1- GENERAL A. Work covered by this section includes the furnishing and installation of conduits and boxes. 1.02 SUBMITTALS A. The Contractor shall
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220529 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Steel pipe hangers and supports. 2. Metal framing systems. 3. Thermal-hanger shield inserts. 4. Fastener systems.
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 1423 - STORM DRAINAGE PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.
PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationSECTION NON-STRUCTURAL METAL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 22 16 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationAddendum #4 NEW LOW HEAD OXYGEN SYSTEM Contractor EXHIBIT T SPECIAL PROVISIONS SECTION METAL SHADE STRUCTURE
SECTION 13 34 00 METAL SHADE STRUCTURE PART 1 - GENERAL 1.01 STRUCTURE TYPE A. Structure shall be free standing rigid frame and gable roof with slopes as indicated. Structure shall also include foundation,
More informationDIVISION 15- MECHANICAL Section Fire Pumps
DIVISION 15- MECHANICAL Section 15320 Fire Pumps 1.00 PART 1 -GENERAL 1.01 DESCRIPTION OF WORK: A. Provide pumps for fire suppression. 1.02 SECTION INCLUDES: A. Vertical Turbine Fire Pump RELATED DOCUMENTS:
More informationSECTION CHAIN LINK FENCING
SECTION 02835 - CHAIN LINK FENCING 1.0 GENERAL 1.1 Furnish and install chain link fencing complete in place with gates and accessories as specified herein and as shown on the Contract Drawings. 1.2 Reference
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 22 PLUMBING. A. This Section includes the following storm drainage piping inside the building.
SECTION 221413 - FACILITY STORM DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following storm drainage piping inside the building. 1. Pipe, tube, and fittings. 2. Special pipe
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Cleanouts. 2. Floor drains. 3. Roof flashing
More information