Product. Regulations. Rockwool Ltd Pencoed Bridgend CF35 6NY Tel: Fax: Agrément Certificate No 93/2884 Second issue*

Transcription

1 CI/SfB (21.9) Rockwool Ltd Pencoed Bridgend CF35 6NY Tel: Fax: Designated by Government to issue European Technical Approvals Rm Agrément Certificate No 93/2884 Second issue* ROCKWOOL HIGH PERFORMANCE PARTIAL FILL CAVITY SLAB Isolation de murs à double paroi Kerndämmung Product THIS CERTIFICATE REPLACES CERTIFICATE No 87/1825 AND RELATES TO ROCKWOOL HIGH PERFORMANCE PARTIAL FILL CAVITY SLAB, AN INSULATION FOR CAVITY WALL INSULATION. The product is for use in buildings up to and including 25 metres in height, subject to the conditions contained in the Design Data part of this Certificate. The product is installed during construction and is for use as a partial fill slab to reduce the thermal transmittance of cavity walls with masonry inner and outer leaves. It is essential that the walls are built in accordance with the conditions set out in the Design Data and Installation parts of this Certificate. The product can be used in breathing wall constructions where other elements have appropriate relative resistance to water vapour transmission. Regulations 1 The Building Regulations 1991 (as amended) () The Secretary of State has agreed with the British Board of Agrément the aspects of performance to be used by the BBA in assessing the compliance of cavity wall insulation with the Building Regulations. In the opinion of the BBA, Rockwool High Performance Partial Fill Cavity Slab, if used in accordance with the provisions of this Certificate, will meet or contribute to meeting the relevant requirements. Requirement: B3(4) Requirement: C4 L1 Conservation of fuel and power The product can meet this Requirement. See sections 11.2 and 11.3 of this Certificate. Requirement: Resistance to weather and ground moisture Walls incorporating the product can meet this Requirement. See sections 7.2 and 9.2 of this Certificate. In addition the product may be used in situations where it bridges the dpc. See section 9.1 of this Certificate. Requirement: Internal fire spread (structure) Walls incorporating the product can meet this Requirement. See sections 8.3 to 8.5 of this Certificate. Regulation 7 Materials and workmanship The product is acceptable. See section 12 of this Certificate. Readers are advised to check the validity of this Certificate by either referring to the Index of Current BBA Publications or contacting the BBA direct (Telephone Hotline ).

2 2 The Building Standards () Regulations 1990 (as amended) In the opinion of the BBA, Rockwool High Performance Partial Fill Cavity Slab, if used in accordance with the provisions of this Certificate, will satisfy or contribute to satisfying the various Regulations and Technical Standards as listed below. Regulation: 10 Fitness of materials Standard: B2.1 Selection and use of materials and components The product is acceptable. Regulation: 12 Structural fire precautions Standard: D2.2 Non-combustibility The product may be used in buildings of any purpose group. See sections 8.3 to 8.5 of this Certificate. Standard: D4.1 Concealed Spaces (cavities) Walls incorporating the product must comply with this Standard. See sections 8.3 to 8.5 of this Certificate. Regulation: 17 Preparation of sites and resistance to moisture Standard: G2.6 Resistance to moisture from the ground The product can satisfy this Standard. See section 9.1 of this Certificate. Standard: G3.1 Resistance to precipitation Walls incorporating the product can satisfy this Standard. See sections 7.2 and 9.2 of this Certificate. Regulation: 22 Conservation of fuel and power Standard: J2.1 Standards for buildings in purpose group 1 Standard: J3.1 Standards for buildings in purpose groups 2 to 7 The product can satisfy these Standards. See sections 11.2 and 11.3 of this Certificate. 3 The Building Regulations (Northern Ireland) 1994 (as amended) In the opinion of the BBA, Rockwool High Performance Partial Fill Cavity Slab, if used in accordance with the provisions of this Certificate, will satisfy or contribute to satisfying the various Building Regulations as listed below. Regulation: B2 Fitness of materials and workmanship The product is acceptable. See section 11 of this Certificate. Regulation: C5 Resistance to ground moisture and weather Walls incorporating the product can satisfy this Regulation. See sections 7.2 and 9.2 of this Certificate. In addition the product may be used in situations where it bridges the dpc. See section 9.1 of this Certificate. Regulation: E6 Internal fire spread Structure Walls incorporating the product can satisfy this Regulation. See sections 8.3 to 8.5 of this Certificate. Regulation: F2 Conservation of fuel and power The product can satisfy this Regulation. See sections 11.2 and 11.3 of this Certificate. 4 Construction (Design and Management) Regulations 1994 Information in this Certificate may assist the client, planning supervisor, designer and contractors to address their obligations under these Regulations. See section: 6 Delivery and site handling. Technical Specification Table 1 Standard sizes (mm) 5 Description 5.1 Rockwool High Performance Partial Fill Cavity Slab consists of layers of bonded, water repellent rock wool formed into resilient slabs using a resin binder; the slabs are heat cured and cut to standard sizes shown in Table 1. 2 Length 1200 Width 455 Thickness 30, 40, 50, 60, 70, 80, 90, All slabs have a belt mark covering one face. The slabs are normally positioned with this face outermost.

3 5.3 Only insulation retaining fixings approved by the BBA should be used with this product. Names and addresses of suppliers of approved fixings are available from Rockwool Ltd and the BBA. 5.4 At the time of publication, insulation retaining fixings approved for use with this system are: Vista VE 2/VE-4 tie with V-23 retaining clip Lexsuco clip with retaining washer Ancon Staifix RT2 with AC Universal Clip Catnic BB-3 Tie and IRC 85 Clip Ancon ST1 Type 1 Tie with Heavy Duty Clip Hemax 90S Heavy Duty Tie and Heavy Duty Retaining Clip Hemax 82 Tie with Universal Retaining Clip (see Figure 1). Figure 1 Wall ties and clips Ancon ST1 Type 1 Tie with Heavy Duty Clip Hemax 82 Tie with Universal Retaining Clip Lexsuco clip with retaining washer 5.5 It should be noted that ties suitable for insulation retaining purposes must also provide appropriate structural stability in accordance with BS 5628 : Part 3 : 1985 or DD 140 : Part 2 : Delivery and site handling 6.1 The slabs are delivered to site compressionwrapped in polyethylene. Each pack carries a label bearing the manufacturer s name, product description, essential instructions for installation and the BBA identification mark incorporating the number of this Certificate. 6.2 Packages must be stored under cover until required for use. Design Data 7 General 7.1 When installed in accordance with this Certificate, Rockwool High Performance Partial Fill Cavity Slab is effective in reducing the U value (thermal transmittance) of new external cavity walls with masonry inner and outer leaves (masonry includes clay and calcium silicate bricks, concrete blocks, natural and reconstituted stone blocks). It is essential that such walls are designed and constructed to incorporate the normal precautions to prevent moisture penetration. 7.2 Buildings subject to national Building Regulations should be constructed in accordance with the relevant recommendations of: BS 5628 : Part 3 : In particular, Clause 21 of the Code of Practice Exclusion of moisture should be followed in that the designer selects a construction appropriate to the local wind-driven rain index paying due regard to the design detailing, workmanship and materials to be used. BS 5390 : 1976(1984), Section 3 where the wall incorporates stone or cast stone. BS 8000 : Part 3 : Other buildings not subject to these Regulations should also be built in accordance with BS 5628 : Part 3 : 1985, BS 5390 : 1976(1984) and BS 8000 : Part 3 : As with all cavity wall insulation the construction detailing should comply with good practice as described in the BBA joint publication Cavity Insulation of Masonry Walls Dampness Risks and How to Minimise Them (see section 9.3 of this Certificate). They are particularly important in areas subject to severe or very severe driving rain. 7.5 The use of cavity battens or boards is strongly recommended to prevent bridging by mortar droppings. 7.6 As with any other form of cavity wall insulation, where buildings need to comply with NHBC Standards or Zurich Building Guarantees Technical Standards, specifiers should observe the requirements of these documents. 3

4 Buildings up to and including 12 metres 7.7 Where a residual cavity width of 50 mm or greater is maintained the product can be used in any exposure zone. However, the use of the product does not preclude the need to apply any external render coat or other suitable finish in severe exposure zones where such application would be normal practice. 7.8 The minimum residual cavity width to be maintained during construction must be 25 mm. To achieve this requirement a greater nominal residual cavity width may need to be specified at the design stage to allow for inaccuracies inherent in the building process. The specifier may either: (1) design a cavity width by consideration of the dimensional tolerances of the components which make up the wall by reference to the British Standards relating to the bricks, blocks and insulation boards or use the data from their respective manufacturers. In addition, allowance may need to be made for the quality of available building operatives and the degree of site supervision or control; or (2) design a nominal residual cavity width of 50 mm (a residual cavity nominally 50 mm wide will be required by the NHBC where normal standards of tolerance and workmanship are adopted). Buildings over 12 metres and up to and including 25 metres 7.9 The width of the residual clear cavity to be achieved is to be in excess of 50 mm, and the following requirements apply: (1) From ground level the maximum height of continuous cavity walls must not exceed 12 metres; above 12 metres the maximum height of continuous cavity walls must not exceed 7 metres. In both cases breaks should be in the form of continuous horizontal cavity trays discharging to the outside. (2) The specifier must take extra care when detailing to ensure that the introduction of the insulation does not affect the weather resistance of the wall. More than average site supervision is recommended during installation of the product. (3) The exposure index does not exceed 120. (4) Where, for structural reasons, the cavity width is reduced, eg by the intrusion of ring beams, a minimum residual cavity width of 25 mm must be maintained and extra care must be taken with fixings and weatherproofing, eg the inclusion of a cavity tray. 8 Behaviour in relation to fire 8.1 Use of the product does not prejudice the fire resistance properties of the wall. 8.2 A sample of the product tested to BS 476 : Part 4 : 1970(1984) achieved the classification non-combustible. 8.3 The requirements of national Building Regulations relating to fire spread in cavity walls, can be met in all purpose groups without the need for cavity barriers provided the construction complies with the provisions detailed in: Approved Document B, Diagram 28. Technical Standard D4.1. Northern Ireland Technical Booklet E, Diagram A summary of these provisions is given here:, and Northern Ireland (1) The wall must consist of masonry inner and outer leaves, each at least 75 mm thick. (2) The cavity must not be more than 100 mm wide (not more than 110 mm for ). (3) The cavity must be closed at the top of the wall and at the top of any opening. (4) In addition to the insulation, only the following should be placed in, or exposed to, the cavity: timber lintels, window or door frames, or end of timber joists pipe, conduit or cables dpc, flashing, cavity closer or wall tie domestic meter cupboard, provided there are not more than two cupboards (three in ) to a dwelling, the opening in the outer leaf is not more than 800 mm by 500 mm for each cupboard, and the inner leaf is not penetrated except by a sleeve not more than 80 mm by 80 mm, which is fire-stopped. 8.5 For constructions not covered by sections 8.3 and 8.4, cavity barriers must be provided to comply with: Approved Document B, Section 9. Technical Standard D4.1. Northern Ireland Technical Booklet E, Paragraphs 3.27 to Liquid water penetration 9.1 When the product is used in situations where it bridges the dpc in walls, dampness from the ground will not pass through to the inner leaf provided the cavity wall is detailed in accordance with the requirements and provisions of the national Building Regulations: Approved Document C, Section 4. Technical Standard G2.6. Provisions deemed to satisfy the standards. 4

5 Northern Ireland Technical Booklet C, Section Constructions built in accordance with BS 5628 : Part 3 : 1985 will resist the transfer of precipitation to the inner leaf and satisfy the national Building Regulations: Requirement C4. Technical Standard G3.1. Northern Ireland Regulation C In all situations it is particularly important to ensure during installation that: (1) wall ties and fixings are installed correctly and are thoroughly clean (2) excess mortar is cleaned from the cavity face of the leading leaf and any debris removed from the cavity (3) mortar droppings are cleaned from the exposed edges of installed boards (4) installation is carried out to the highest level on each wall or the top edge of the insulation is protected by a cavity tray. 10 Water vapour penetration The product has minimal resistance to the diffusion of moisture vapour (typically resistivity 5 MNsg 1 m 1 ). 11 Thermal insulation 11.1 For the purpose of U value calculations to determine if the requirements of the Building (or other statutory) Regulations are met, the thermal conductivity ( value) of the insulation may be taken as Wm 1 K The requirement for limiting the heat loss through the building fabric can be satisfied if the U values of the building elements do not exceed the maximum values in the relevant Elemental Methods given in the national Building Regulations: Approved Document L. The effect of thermal bridging should be taken into account. Technical Standards, Part J. The effect of thermal bridging should be taken into account. Northern Ireland Technical Booklet F Guidance is also given in these documents on selecting the thickness of insulation required to enable a wall to achieve the desired U value. Alternative approaches are also described which allow for some flexibility in design of U values for individual constructional elements. 12 Durability The product is stable, rot-proof and durable, and will remain effective as an insulation system for the life of the building, provided it is installed in accordance with this Certificate. Installation 13 General The walls are constructed with the inner leaf leading. Rockwool High Performance Partial Fill Cavity Slab is fastened to the cavity face of the inner leaf. 14 Procedure 14.1 A section of the inner leaf is built with the first row of wall ties, at approximately 600 mm horizontal spacing, where the insulation is to begin. It is recommended that the wall ties are not placed directly on the damp-proof course. The first run of slabs may commence below the damp-proof course level to provide some edge insulation for the floor (see Figure 2) The inner leaf is built up to the required height, with wall ties placed at a vertical height of 450 mm. Excess mortar is cleaned from the cavity face of the leading leaf, and the slabs are compressed slightly between the upper and lower wall ties, behind the retaining clips, to form a closely butt-jointed run The second row of wall ties is fitted to retain the tops of the slabs. It is essential that all wall ties slope downwards towards the outer leaf (see Figure 3) and at centres not exceeding 600 mm to ensure that each slab is secured at a minimum of four points. Additional ties may be required to satisfy the structural requirements of BS 5628 : Part 3 : 1985 and/or to ensure adequate retention of slabs or cut pieces Alternatively, the slabs are retained against the leading leaf by the Lexsuco clips [see Figure 2(c)] which are pressed lightly through the insulation and located in the green mortar bed 5

6 joint, except at dpc level where the clips may be located in the perpend joints. It is important that the mortar should have the correct consistency; it should be stiff enough to retain the clip yet soft enough to avoid any hammering into place. Three clips per slab are required at approximately 400 mm centres 14.5 The outer leaf is then built up to the level of the top of the slabs Progressive staggering of slabs and wall ties as construction proceeds should be in accordance with the manufacturer s recommendations Where additional ties are required, at less than 450 mm vertical spacing, Rockwool slabs must be cut and neatly fitted around them. Under no circumstances should they be impaled over ties The slabs should be close butted at corners (see Figure 4). It is recommended that whole slabs should be used at corners, but if this is not possible the butting face should be factory cut. Mortar droppings 14.9 After each section of the leading leaf is built, excess mortar should be removed from the cavity face and mortar droppings cleaned from exposed edges of the installed slabs, before installation of the next run of slabs. Use of a cavity board or a cavity batten will protect the installed slabs and help to keep the cavity clean as the following leaf is built (see Figure 5). Cut pieces Slabs can be cut, using a sharp knife or fine-toothed saw, to fit openings, eg around windows, doors, air bricks. It is essential that cut pieces completely fill the spaces for which they are intended and are adequately secured. Protection All building involving the boards, particularly interrupted work, must conform to BS 5628 : Part 3 : 1985, Sections 30 Storage on site, 35 Protection against damage during construction, and 36 Supervision. Technical Investigations The following is a summary of the technical investigations carried out on Rockwool High Performance Partial Fill Cavity Slab. 15 Investigations 15.1 An examination was made of data on which the previous Certificate was based Regular factory inspections have been carried out to ensure that quality is being maintained No failure of the product in use has been reported to the BBA. Figure 2 Rockwool Partial Fill Cavity Slab fixing systems 6

7 Figure 3 Wall tie detail Figure 5 Use of cavity board or batten wall ties must slope down towards outer leaf (a) with cavity board Figure 4 Slabs close-butted at corner (b) with cavity batten Bibliography BS 476 Fire tests on building materials and structures Part 4 : 1970(1984) Non-combustibility test for materials BS 1243 : 1978 Specification for metal ties for cavity wall construction BS 5390 : 1976(1984) Code of practice for stone masonry BS 5628 Code of practice for use of masonry Part 3 : 1985 Materials and components, design and workmanship BS 8000 Workmanship on building sites Part 3 : 1989 Code of practice for masonry DD 140 Wall ties Part 2 : 1987 Recommendations for design of wall ties 7

8 Conditions of Certification 16 Conditions 16.1 This Certificate: (a) relates only to the product that is described, installed, used and maintained as set out in this Certificate; (b) is granted only to the company, firm or person identified on the front cover no other company, firm or person may hold or claim any entitlement to this Certificate; (c) has to be read, considered and used as a whole document it may be misleading and will be incomplete to be selective; (d) is copyright of the BBA References in this Certificate to any Act of Parliament, Regulation made thereunder, Directive or Regulation of the European Union, Statutory Instrument, Code of Practice, British Standard, manufacturers instructions or similar publication, shall be construed as references to such publication in the form in which it was current at the date of this Certificate This Certificate will remain valid for an unlimited period provided that the product and the manufacture and/or fabricating process(es) thereof: (a) are maintained at or above the levels which have been assessed and found to be satisfactory by the BBA; (b) continue to be checked by the BBA or its agents; and (c) are reviewed by the BBA as and when it considers appropriate In granting this Certificate, the BBA makes no representation as to: (a) the presence or absence of any patent or similar rights subsisting in the product or any other product; (b) the right of the Certificate holder to market, supply, install or maintain the product; and (c) the nature of individual installations of the product, including methods and workmanship Any recommendations relating to the use or installation of this product which are contained or referred to in this Certificate are the minimum standards required to be met when the product is used. They do not purport in any way to restate the requirements of the Health & Safety at Work etc Act 1974, or of any other statutory, common law or other duty which may exist at the date of this Certificate or in the future; nor is conformity with such recommendations to be taken as satisfying the requirements of the 1974 Act or of any present or future statutory, common law or other duty of care. In granting this Certificate, the BBA does not accept responsibility to any person or body for any loss or damage, including personal injury, arising as a direct or indirect result of the installation and use of this product. In the opinion of the British Board of Agrément, Rockwool High Performance Partial Fill Cavity Slab is fit for its intended use provided it is installed, used and maintained as set out in this Certificate. Certificate No 93/2884 is accordingly awarded to Rockwool Ltd. On behalf of the British Board of Agrément Date of Second issue: 18th January 1999 Director *Original Certificate issued 3rd March This amended version includes references to the revised Building Regulations and associated text, revised Conditions of Certification, and references to the enhanced product robustness. British Board of Agrément P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD2 7NG Fax: mail@bba.star.co.uk For technical or additional information, tel: For information about Agrément Certificate validity and scope, tel: Hotline: