MATERIAL SAFETY DATA SHEET

Transcription

1 MATERIAL SAFETY DATA SHEET Product Trade Name: Revision Date: 05-Jan CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Trade Name: Synonyms: Chemical Family: Application: Manufacturer/Supplier Prepared By None Organic acid Anhydride Additive Halliburton Energy Services P.O. Box 1431 Duncan, Oklahoma Emergency Telephone: (281) Chemical Compliance Telephone: COMPOSITION/INFORMATION ON INGREDIENTS SUBSTANCE CAS Number PERCENT ACGIH TLV-TWA OSHA PEL-TWA Acetic anhydride % 5 ppm 5 ppm Acetic acid % 10 ppm 10 ppm 3. HAZARDS IDENTIFICATION Hazard Overview May cause eye, skin, and respiratory burns. May be harmful if swallowed. Combustible. Reacts violently with water. 4. FIRST AID MEASURES Inhalation If inhaled, remove to fresh air. If not breathing give artificial respiration, preferably mouth-to-mouth. If breathing is difficult give oxygen. Get medical attention. Skin In case of contact, immediately flush skin with plenty of soap and water for at least 15 minutes. Get medical attention. Remove contaminated clothing and launder before reuse. Destroy or properly dispose of contaminated shoes. Eyes Ingestion Notes to Physician In case of contact, or suspected contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention immediately after flushing. Do not induce vomiting. Slowly dilute with 1-2 glasses of water or milk and seek medical attention. Never give anything by mouth to an unconscious person. Not Applicable Page 1 of 6

2 5. FIRE FIGHTING MEASURES Flash Point/Range (F): 103 Flash Point/Range (C): 39 Flash Point Method: PMCC Autoignition Temperature (F): 630 Autoignition Temperature (C): 332 Flammability Limits in Air - Lower (%): 3 Flammability Limits in Air - Upper (%): 19 Fire Extinguishing Media Special Exposure Hazards Carbon Dioxide, Dry Chemicals, Foam. Water must not be used with open containers. May be ignited by heat, sparks or flames. Closed containers may explode in fire. Decomposition in fire may produce toxic gases. Reaction with water may be highly exothermic. Special Protective Equipment for Fire-Fighters Full protective clothing and approved self-contained breathing apparatus required for fire fighting personnel. NFPA Ratings: Health 3, Flammability 2, Reactivity 2 HMIS Ratings: Health 3, Flammability 2, Physical Hazard 2 6. ACCIDENTAL RELEASE MEASURES Personal Precautionary Measures Use appropriate protective equipment. Environmental Precautionary Measures Procedure for Cleaning / Absorption Prevent from entering sewers, waterways, or low areas. Isolate spill and stop leak where safe. Contain spill with sand or other inert materials. Neutralize to ph of 6-8. Scoop up and remove. 7. HANDLING AND STORAGE Handling Precautions Storage Information Avoid contact with eyes, skin, or clothing. Avoid breathing vapors. Wash hands after use. Launder contaminated clothing before reuse. Store away from alkalis. Store away from oxidizers. Store away from water. Keep from heat, sparks, and open flames. Keep container closed when not in use. Product has a shelf life of 60 months. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering Controls Respiratory Protection Hand Protection Skin Protection Eye Protection Other Precautions Use in a well ventilated area. Local exhaust ventilation should be used in areas without good cross ventilation. Organic vapor/acid gas respirator. Impervious rubber gloves. Rubber boots. Full protective chemical resistant clothing. Chemical goggles; also wear a face shield if splashing hazard exists. Eyewash fountains and safety showers must be easily accessible. Page 2 of 6

3 9. PHYSICAL AND CHEMICAL PROPERTIES Physical State: Liquid Color: Clear colorless Odor: Pungent acrid ph: < 2 Specific 20 C (Water=1): C (lbs./gallon): Bulk 20 C (lbs/ft3): Boiling Point/Range (F): 259 Boiling Point/Range (C): 126 Freezing Point/Range (F): Freezing Point/Range (C): Vapor 20 C (mmhg): 11.7 Vapor Density (Air=1): 3.5 Percent Volatiles: 100 Evaporation Rate (Butyl Acetate=1): 0.97 Solubility in Water (g/100ml): Soluble Solubility in Solvents (g/100ml): VOCs (lbs./gallon): Viscosity, 20 C (centipoise): Viscosity, 20 C (centistrokes): Partition Coefficient/n-Octanol/Water: Molecular Weight (g/mole): 10. STABILITY AND REACTIVITY Stability Data: Hazardous Polymerization: Conditions to Avoid Incompatibility (Materials to Avoid) Hazardous Decomposition Products Additional Guidelines Stable Will Not Occur Keep away from heat, sparks and flame. Do not allow water to get into container because of violent reaction. Strong alkalis. Strong oxidizers. Reacts with water. Carbon monoxide and carbon dioxide. Not Applicable 11. TOXICOLOGICAL INFORMATION Principle Route of Exposure Inhalation Skin Contact Eye Contact Ingestion Aggravated Medical Conditions Chronic Effects/Carcinogenicity Other Information Eye or skin contact, inhalation. Causes severe respiratory irritation. Causes severe burns. Causes severe eye burns. Causes burns of the mouth, throat and stomach. Skin disorders. Eye ailments. Prolonged, excessive exposure may cause erosion of the teeth. None known. Toxicity Tests Page 3 of 6

4 Oral Toxicity: Dermal Toxicity: Inhalation Toxicity: Primary Irritation Effect: Carcinogenicity Genotoxicity: Reproductive / Developmental Toxicity: 12. ECOLOGICAL INFORMATION Mobility (Water/Soil/Air) Persistence/Degradability Readily biodegradable Bio-accumulation Ecotoxicological Information Acute Fish Toxicity: Acute Crustaceans Toxicity: Acute Algae Toxicity: Chemical Fate Information Other Information Not applicable 13. DISPOSAL CONSIDERATIONS Disposal Method Contaminated Packaging Disposal should be made in accordance with federal, state, and local regulations. Follow all applicable national or local regulations. 14. TRANSPORT INFORMATION Land Transportation DOT UN2920,Corrosive Liquid, Flammable, N.O.S.(Contains Acetic Anhydride, Acetic Acid), 8, (3), II, (39.4 C) NAERG 132 Canadian TDG Corrosive Liquid, Flammable, N.O.S.(Contains Acetic Anhydride, Acetic Acid), 8, (3), UN2920, II, (39.4 C) ADR UN2920,Corrosive Liquid, Flammable, N.O.S.(Contains Acetic Anhydride, Acetic Acid), 8, (3), II Air Transportation Page 4 of 6

5 ICAO/IATA UN2920,Corrosive Liquid, Flammable, N.O.S., 8, (3), II (Contains Acetic Anhydride, Acetic Acid Solution) Sea Transportation IMDG UN2920,Corrosive Liquid, Flammable, N.O.S.(Contains Acetic Anhydride, Acetic Acid), 8, (3), II, (39.4 C) EmS F-E, S-C Other Shipping Information Labels: Corrosive Flammable Liquid 15. REGULATORY INFORMATION US Regulations US TSCA Inventory EPA SARA Title III Extremely Hazardous Substances EPA SARA (311,312) Hazard Class All components listed on inventory or are exempt. Not applicable Acute Health Hazard Fire Hazard EPA SARA (313) Chemicals EPA CERCLA/Superfund Reportable Spill Quantity EPA RCRA Hazardous Waste Classification This product does not contain a toxic chemical for routine annual "Toxic Chemical Release Reporting" under Section 313 (40 CFR 372). EPA Reportable Spill Quantity is 1409 Gallons based on Acetic acid (CAS: ). If product becomes a waste, it does meet the criteria of a hazardous waste as defined by the US EPA, because of: Ignitability D001 Corrosivity D002 California Proposition 65 MA Right-to-Know Law NJ Right-to-Know Law PA Right-to-Know Law All components listed do not apply to the California Proposition 65 Regulation. One or more components listed. One or more components listed. One or more components listed. Canadian Regulations Canadian DSL Inventory WHMIS Hazard Class All components listed on inventory. B3 Combustible Liquids E Corrosive Material Page 5 of 6

6 16. OTHER INFORMATION The following sections have been revised since the last issue of this MSDS Not applicable Additional Information For additional information on the use of this product, contact your local Halliburton representative. For questions about the Material Safety Data Sheet for this or other Halliburton products, contact Chemical Compliance at Disclaimer Statement This information is furnished without warranty, expressed or implied, as to accuracy or completeness. The information is obtained from various sources including the manufacturer and other third party sources. The information may not be valid under all conditions nor if this material is used in combination with other materials or in any process. Final determination of suitability of any material is the sole responsibility of the user. ***END OF MSDS*** Page 6 of 6