Product Information. Monolec Turbine Oil ( ) Premium Oil Boosts Turbine Performance. The Lubrication Reliability Source

Transcription

1 Product Information Monolec Turbine Oil ( ) Premium Oil Boosts Turbine Performance Highly effective for steam, hydro and gas turbine applications, Monolec Turbine Oil ( ) reduces varnish, reduces water contamination, lengthens equipment life and extends drain intervals. It is a premium, highperformance turbine oil with excellent water separation characteristics, rust and oxidation inhibitors, and improved wear-reducing properties. Its proprietary formula consists of select low-volatility paraffinic base fluids enhanced with a synergistic mix of high-performance additives. Certain turbine applications including gear-driven turbines or those in which a hydraulic control system and turbine share the same oil require oil with anti-wear properties. Unlike many anti-wear additives that decrease the oxidation resistance of turbine oils, the proprietary wear-reducing additive in Monolec Turbine Oil provides increased protection against wear with no negative effect on the oxidation life of the oil. Beneficial Qualities Reduces Varnish & Deposits in Gas & Steam Turbines Exhibits excellent thermal stability Has rapid air release properties Resists formation of varnish and sludge Reduces Water Contamination in Steam & Hydro Turbines Separates readily from water Provides excellent resistance to foaming Imparts superior rust protection Lengthens Equipment Life Protects moving parts, due to its high film strength Enhances wear-reducing properties without affecting R & O inhibitors º Protects thrust plates in bearings Extends Drain Intervals Provides long-term oxidation resistance and thermal stability Is easily filtered for long-term oil cleanliness Available Grades ISO 68 (6463) ISO 46 (6462) ISO 32 (6461) Proprietary Additive LE s proprietary additives are used exclusively in LE lubricants. Monolec Turbine Oil contains Monolec. Monolec wear-reducing additive is an invaluable component in LE s engine oils, industrial oils and many of its other lubricants. Monolec creates a singular molecular lubricating film on metal surfaces, vastly increasing film strength without affecting clearances. It allows opposing surfaces to slide by one another, greatly reducing friction, heat and wear. The Lubrication Reliability Source

2 Technical Data Monolec Turbine Oil Color Amber Amber Amber ISO VG / SAE Grade Gravity API, ASTM D C, cst, ASTM D C, cst, ASTM D Viscosity Index ASTM D Flash Point C ( F), (COC), ASTM D (460) 234 (455) 228 (442) Pour Point C ( F), ASTM D95-24 (-11) -30 (-22) -30 (-22) Rust Test 4 60 C (140 F), Sea H 2 0, ASTM D665B Pass Pass Pass Copper Corrosion C (212 F), ASTM D130 1b 1b 1b Oxidation by TOST hours, ASTM D943 >4,000 >4,000 >4,000 Oxidation by 150 C (302 F), minutes, ASTM D Air Release Min., ASTM D Color ASTM D Panel Coker mg, FTM Filterability wet, Stage I, ISO Pass Pass Pass Low Temperature Stability FTM 3458 Pass Pass Pass Four-Ball 75 C, 1,200 rpm, 40 kgf, 60 minutes, mm wear, ASTM D Ash Sulfated %, ASTM D Acid Number mg KOH/g, ASTM D Max 0.15 Max 0.15 Max Emulsion 54 C (130 F), oil-water-emulsion/minutes, ASTM D1401 Performance Requirements Met or Exceeded Alstom Cincinnati Machine DIN Part 1 General Electric ISO 8068 (L-TSA & L-TGA) Recommendations MIL-H-17672D 2075 TH Siemens Solar Turbine USDA H2 Westinghouse Monolec Turbine Oil is suitable for all mainline and peaking turbine applications. Typical Applications Mainline steam, hydro and gas turbine generators Circulating oil systems Centrifugal compressors Other long-service-life applications / / /5 Siemens AG, Picture: Martin Adam Monolec is a registered trademark of Lubrication Engineers, Inc. 300 Bailey Avenue Fort Worth, TX Fax: LE products manufactured under an ISO 9001:2000 Certified Quality System LI

3 LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION SUPPLIER: EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX Chemtrec: (Within USA) (800) (Outside USA call collect) (703) CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS: 6461 MONOLEC Turbine Oil CHEMICAL FAMILY: Hydrocarbon FORMULA: SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES APPEARANCE: 210 F, 100 C, cst Amber lubricant ODOR: 100 F, 40 C, cst Lube oil odor RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: POUR POINT: F -22 BOILING POINT: F FLASH POINT: F (Method) > (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm 60 F) < SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD50 LD50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) > mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS. This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC ) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 442 F (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials MONOLEC Turbine Oil Effective Date: October 27, 2008 Print Date: January 20, 2009 Page 1

4 INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S and N; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity MONOLEC Turbine Oil Effective Date: October 27, 2008 Print Date: January 20, 2009 Page 2

5 SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX Chemtrec: (Within USA) (800) (Outside USA call collect) (703) CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon TRADE NAME AND SYNONYMS: 6462 MONOLEC Turbine Oil FORMULA: SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES APPEARANCE: 210 F, 100 C, cst Amber lubricant ODOR: 100 F, 40 C, cst Lube oil odor RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -22 BOILING POINT: F FLASH POINT: F (Method) > (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm 60 F) < SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) > mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC ) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 455 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: 6462 MONOLEC Turbine Oil Effective Date: April 3, 2008 Print Date: January 20, 2009 Page 1

6 Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S and N; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity MONOLEC Turbine Oil Effective Date: April 3, 2008 Print Date: January 20, 2009 Page 2

7 LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION SUPPLIER: EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX Chemtrec: (Within USA) (800) (Outside USA call collect) (703) CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS: 6463 Monolec Turbine Oil CHEMICAL FAMILY: Hydrocarbon FORMULA: SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES APPEARANCE: 210 F, 100 C, cst Amber lubricant ODOR: 100 F, 40 C, cst Lube oil odor RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -11 BOILING POINT: F FLASH POINT: F (Method) > (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm 60 F) < SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) > mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC ) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 460 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials Monolec Turbine Oil Effective Date: April 3, 2008 Print Date: January 20, 2009 Page 1

8 INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S and N; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity Monolec Turbine Oil Effective Date: April 3, 2008 Print Date: January 20, 2009 Page 2