SPECIFICATION FOR APPROVAL

Transcription

1 SPECIFICATION FOR APPROVAL CUSTOMER 菱洋 MODEL NO. PART NO. MODEL NAME DATE BPCE030C701 LKBPCE030C701-P W 42V LED DRIVER 2010/1/20 APPROVED SIGNATURES LinkCom Manufacturing Co., Ltd (Taiwan Headquarter) 5F,NO.127, Lane 235,Bao-Chiao Road, Hsintien City, Taipei County, Taiwan R.O.C. Tel: (886) Fax: (886) (China Plant 1) Technology Industrial Park, Chi-Si Town, Dong Guang City, P.R.China Tel: (86-769) Fax: (86-769)

2 Index I. Index II. Record of Revision 1. Electrical Specification ~ Environmental Specification Regulatory Compliance ~ Mechanical ~ Packing Component Agency Certificate ~6-6 Approved Signatures Approved by: Checked by: Reported by:

3 Record of Revision Rev Description Changes Date 0.0 First Draft 2010/01/20 A

4 1. Electrical Specification 1.1 Input requirement Electrical Specification Input voltage range The power shall operate within specification from 90 to 264Vac or provide automatic switching in two ranges. The table below shows common input voltage range. Input range Minimum Nominal Maximum Unit / Vac Table 1-Input Voltage Range Input frequency range The power shall operate within specification form 50 to 60Hz AC inrush current Peak inrush current should not exceed 50 A, measured at 230Vac, 60Hz, 25, cold start. It should not interrupt line fuse or cause damage to the LED driver either at cold or warm start Input current Maximum steady state input current shall not exceed 0.5 A for any line voltage specified in Input protection A fuse with rating of 3.15 A/ 250 V shall be installed on the input side near the input connector to provide protection to LED driver. 1.3 Output requirement Output power The output power is 29.4W. (Output voltage* output current) Note: The output connection of this power supply that is used in LED lighting shall be defined to avoid LED damage. Please take notice of

5 Electrical Specification Output voltage and current Under any combination of line and load variation and environmental conditions, all outputs shall remain within tolerance defined in Table 2. Output voltage(s) shall be measured at load side of output connector. Voltage Range Current Range Output Voltage Lower Limit Upper Limit Minimum Load Full rated load 42V 42V-10% 42V+10% 0.1A 0.7A Table 2-Output Voltage and Current 3 Ripple and noise Measurements shall be made with an oscilloscope with minimum of 20MHz band width. Output shall be bypassed at the connector with a 0.1uF ceramic disk capacitor and a 10uF electrolytic capacitor for general testing purpose. Output Voltage Maximum Ripple & Noise (Vp-p) 42V 2.6V (Max.) Table 3- Ripple and Noise Over voltage protection The power shall be provided with over voltage protection such that any component failure, output channel shall exceed the voltages specified, the first will clamp, second will latch minimum load 0.1A. Output Voltage Voltage Range 42V 47~57V Table 4- Over Voltage Protection Note: In the event of latch an over-voltage condition on output voltage, The LED driver shall shutdown and require remove the AC mains Over Current Over Current limiting shall operate at <110% Overshoot and undershoot During turn on, turn off condition, the output overshoot shall not exceed nominal voltage by more than 10%, and output shall not change its polarity with respect to its return line Short circuit protection The power shall have self-limiting protection to protect against short circuit No damage to the LED driver shall result from a continuous or intermittent short circuit condition. 1-2

6 1.4 Performance requirement Efficiency Electrical Specification Efficiency (watt out/ watt in) is a minimum of 85 % at 115Vac/60Hz, full rated load Turn on and delay time Output shall reach steady state in 3 seconds of turn on Hold-up time Hold-up time shall be a minimum of 10 ms at 25, 115Vac/60Hz of input at full rate load Dynamic load The power shall operate within regulation defined in section at following conditions: Step load change: form 0.1 A to 0.7 A load on the output. Dwell time: 100Hz & 1KHz 50% duty. Slew rate: 0.1A/usec 1-3

7 Environmental Specification 2. Environmental Specification 2.1 Temperature Parameter Min. Max. Unit Operating ambient temperature C Storage ambient temperature C Table 5-Temperature 2.2 Humidity Parameter Min. Max. Unit Remark Operating ambient humidity % Non-Condensing Storage ambient humidity % Non-Condensing The power shall comply with IP67 indoor/outdoor waterproof requirements. 2.3 Vibration Operating: Hz, 0.25G peak to peak, 3 axes, 15 min sweep. Storage: Hz, 2.0G peak to peak, 3 axes, 15 min sweep. 2.4 Reliability (Mean Time Between Failures, MTBF) The power shall have a calculated MTBF of greater than 50,000 hours, calculated utilizing MIL-HDBK-217F with the following assumptions: Input voltage: 100Vac / 50Hz Output load: Rated full load Ambient temperature: 25 Warranty: We provide two years warranty for our full range LED power supply product. 2-1

8 3. Regulatory Compliance 3.1 Emission Regulatory Compliance (EN55015:2000+A1:200+A2:2002) Disturbance Voltages atmains Terminals load&contronl Terminals Measurement Meets limits Radiated Electromagnetic Disturbance Meets limits Harmonic current emissions,en Meets Class C requirements Voltage fluctuations&flicker,en Meets the requirements 3.2 Immunity (EN 61547: 1995+A1: 2000) Electrostatic Discharge (ESD), EN Power supply shall withstand +/- 4KV contact discharge and +/- 8KV air discharge at any point on the power supply enclosure without functional failure Radiated field Immunity, EN Power supply shall withstand following condition: Frequency range: MHz Field strength: 3 V/m with 80% amplitude modulation of 1KHz Fast transient Immunity, EN Power supply shall withstand EN /-2KV requirements. 3-1

9 Regulatory Compliance Surge Immunity, EN Power supply shall withstand +/-2KV (L-L) and +/-2.3KV (L-PE) without functional failure Conducted Immunity, EN Power supply shall withstand following condition: Frequency range: 0.15~80MHz Field strength: 3 V/m with 80% amplitude modulation of 1KHz Conducted Immunity, EN Power supply shall withstand following condition: Frequency range: 50/60Hz Field strength: 3 A/m Voltage Dips and Interruptions, EN Power supply shall meet EN requirements Product safety compliance Unless otherwise specified, the supply is designed to meet PSE and/or equivalent safety standards for use in LED lighting system. For Specific agency certifications will be applied at customer s request and cost. Please take notice of Appendix I Country Certification File NO./Report NO. JAPAN PSE JET

10 4. Mechanical Mechanical 4.1 Outline dimension and label drawing 4-1

11 Mechanical No Item Q ty Material Remark 1 Input line 1 H05S-F/PSE JET 2C*0.75mm 2 Black 2 Output line 1 H05S-F/PSE JET 2C*0.75mm 2 Gray 3 Label 1 Silver polyester film 79.5*39.5 mm 4 Case cover 1 PBT<ROHS> 5 Case bottom 1 PBT<ROHS> 4.2 Label drawing 4-2

12 Mechanical 4.3 LED connection recommendation as the following 700mA D1 DIODE LED D4 DIODE D5 DIODE 9-12 pcs (Vf=3.5V) D12 700mA DIODE D1 DIODE D1 DIODE LED 350mA 350mA Each Row 9-12 pcs LED (Vf=3.5V) D11 DIODE D12 DIODE D11 DIODE D12 DIODE 700mA The other application such current couldn t approach Limitation, then voltage will attain to 42V 4-3

13 4.4 Barcode sticker Mechanical Code 1 H Code 2 G Code 3 3 Code 4 9 Code 5 9 Code 6 0 Code 7 8 Code 8 1 Code 9 0 Code 10 0 Code 11 0 Code 12 1 Factory's management No. The last number of year The month (10=A,11=B,12=C) The week ECN No.;0~9 Version., when the number is exceeding 10, shows A-Z (10=A,11=B ) The weekly production No.; when the number is 10K, shows A000 (10001=A001,10K=A,20K=B) 4-4

14 Equiv. SELV IP67 INPUT LIN KC OM M ANU FA CTU RING GO.,LTD. OUTPUT LED Power Supply Model: BPCE030CXXX Input: VAC A 50-60HZ Output: VDC A BAUART.. G EPRUFT 110 TUV F M M a R h ei nl and TYPE EMC P r od uct S af et y APPROVED t c LinkCom Manufacturing Co., Ltd 5.Packing Packing Specification <1> Model Number BPCE030CXXX-XX <2> Customer <3> Product Size 152*53*39.5mm <4> Version 1.0 <5> Package Item: 1. Each box Qty. 5 X (Total box in layer) 2 = 10 PCS 2. Each layer Qty. 10 X (Total layer in carton)2 = 20 PCS <6>Product weight unit 416 g N.W kg G.W Kg <7> Packing Illustration: Paperboard Inner box Carton Inner box Stack 10*2=20pcs Box dimensions:243*75*44mm Carton dimensions:500*388*123mm <8> Pallet packing Illustration: 800mm (REF) Total carton in pallet : 4*5 = 20 Total weight : 20*10.32 = kg 800mm (REF) 1160mm (REF) <10> Carton outside <11> Remark: GP LABEL 5-1

15 Appendix I Component Agency Certificate 6-1

16 Appendix I Component Agency Certificate 6-2

17 Appendix I Component Agency Certificate 6-3

18 Appendix II Component Agency Certificate 6-4

19 Appendix III Component Agency Certificate 6-5

20 Appendix IV Component Agency Certificate 6-6