RMANCE ROCKPANEL. EL Durable 8 mm. System 1. inorganic finish. Konstruktieweg. Tel. Fax. Notified. Body: 1. Unique. 4. System as set.

Transcription

1 ROCKWOOL B.V. / ROCKPANEL Groupp Konstruktieweg 2 NL-6045 JD Roermond Netherlands DECLARATION OF PERFOR RMANCE No CPR-0238 DK - english - vs01 1. Unique identificationn code of the product-type: ROCKPANEL Durable 8 mm finish Colours/Rockclad and ROCKPANER EL Durable 8 mm finish ProtectPlus 2. Intended use / es Internal and external wall and ceilingg finishes 3. Manufacturer ROCKWOOL B.V. / ROCKPANEL Group Konstruktieweg 2 NL-6045 JD Roermond, Netherlands Tel Fax System systems of AVCP (assessment and verification of constancy of perfmance p of the construction product) as set out in Annex V (amended by : OJ L 157, , p ) System 1 5. European Assessment Document: EAD f Prefabricated compressed mineral wool boards with ganic inganic finish and with specified fastening system, edition May European Technical Assessment: of 15/12/2014 Technical Assessment Body: ETA-Danmark A/ /S Göteburg Plads 1, DK-2150 Ndhavn, Denmark Tel Fax Internet Notified Body: Materialprüfanstalt für das Bauwesen B Nienburger Strasse 3, D Hannover, Germany Notified Body 0764 Tel Fax Internet and issued: Certificate of Constancy of perfmance No CPR 0238 ROCKWOOL BV / ROCKPANEL Group Page 1 of 13 DECLARATION OF PERFORMANCE 0764-CPR-0238-DK-english-vs01

2 6. Characteristics of the product The ROCKPANEL Durable Colours panels are surface treated with a four-layer water-bne polymer emulsion paint on one side, in a range of colours. The ROCKPANEL Durable ProtectPlus panels are surface treated with a four-layer water-bne polymer emulsion paint on one side, which has been provided with an extra anti-graffiti clear coat as a fifth layer on the colour paint. The physical properties of ROCKPANEL DURABLE 8 mm are indicated below: - thickness 8 ± 0,5 mm - length, max 3050 mm - width, max 1250 mm - density nominal 1050 kg/m³ - bending strength length and width f N/mm² - Modulus of Elasticity 4015 N/mm² - Thermal conductivity 0,37 W/(m.K) Clause 7 contains the perfmances of ROCKPANEL DURABLE 8 mm. ROCKWOOL BV / ROCKPANEL Group Page 2 of 13 DECLARATION OF PERFORMANCE 0764-CPR-0238-DK-english-vs01

3 7. Declared perfmance s Basic Requirements f construction wks BR2 - Safety in case of fire Perfmance Table 1 - Euroclass classification of different constructions with ROCKPANEL boards vertical wooden vertical aluminum Fixing Ventilated non-ventilated subframe subframe method Durable Colours and Durable ProtectPlus Non-ventilated. B-s1,d0 Cavity filled with mineral wool closed hizontal joint Ventilated with EPDM gasket on the B-s2,d0 battens [a] [d] open 6 mm hizontal joint Ventilated with 6 8 mm mechanically fixed B-s2,d0 ROCKPANEL strips on the battens open 6 mm hizontal joint [b] [d] bonded Ventilated with 8 mm ROCKPANEL strips on the battens [b] ventilated with 8 mm ROCKPANEL strips on the battens [b] ventilated [a] width of the gasket 15 mm at both sides wider than the batten [b] width of the strip 15 mm at both sides wider than the batten B-s1,d0 open 6 mm hizontal joint f finish white and black [c] B-s2,d0 open 6 mm hizontal joint B-s2,d0 open 6 mm hizontal joint [c] also valid f a mixture of the colours white and black [d] also valid f boards with a primer finish EN Field of application The following field of application applies. Euroclass classification The classification mentioned in table 1 is valid f the following end use conditions: Mounting Mechanically fixed adhered as described in table 1, which are attached to the subframe mentioned below Adhered to a wooden subframe with intermediate ROCKPANEL strips mechanically fixed The panels are backed with minimum 50 mm mineral wool insulation with density kg/m³ accding to EN with a cavity between the panels and the insulation (mechanically fixed) The panels are backed with minimum 40 mm mineral wool insulation with density kg/m³ accding to EN without an air gap between the wooden subframe (mechanically fixed non ventilated) The panels are backed with minimum 50 mm mineral wool insulation with density kg/m³ accding to EN with a cavity between the panels and the insulation (fixing method Adhesive ROCKPANEL Tack-S) Substrates: Concrete walls, masonry walls, timber framing Page 3 of 13

4 Insulation: Ventilated constructions: The battens are backed with minimum 50 mm mineral wool insulation with density kg/m³ accding to EN with a cavity of minimum 28 mm between the panels and the insulation Non-ventilated constructions: The panels are backed with minimum 40 mm mineral wool insulation with kg/m³ between the battens and minimum 50 mm with density kg/m³ behind the battens without air gap Ventilated construction and fixing method adhesive ROCKPANEL Tack-S: The panels are backed with minimum 50 mm mineral wool insulation with density kg/m³ accding to EN with a cavity of minimum 36 mm between the panels and the insulation Results are also valid f all greater thickness of mineral wool insulation layer with the same density and the same better reaction to fire classification Subframe: Vertical softwood battens without fire retardant treatment, thickness minimum 28 mm Test results are also valid f the same type of panel with aluminum steel frame Test results are also valid f the same type of panel with vertical LVL battens, without fire retardant treatment, thickness minimum 27 mm Fixings: Results are also valid with higher density of the fixing devices Test results are also valid f the same type of panel fixed by rivets made of the same material of screws and vice versa Cavity: Unfilled filled with insulation of stone wool with a nominal density kg/m³ accding to EN The depth of the cavity is minimum 28 mm Test results are also valid f other higher thickness of air space between the back of the board and the insulation Joints: Vertical joints are with an EPDM foam gasket backing (Celdex EPDM Soft EP-4530) ROCKPANEL strip backing as described in table 1 and hizontal joints can be open (ventilated constructions) with an aluminum profile (ventilated and non-ventilated constructions) The result from a test with an open hizontal joint is also valid f the same type of panel used in applications with hizontal joints closed by steel aluminum profiles The classification is also valid f the following product parameters: Thickness: Nominal 8 mm, individual tolerances ± 0,5 mm Density: Nominal 1050 kg/m 3. Page 4 of 13

5 s BR3 Hygiene, health and environment Table 2 - Perfmance - Water vapour permeability and water permeability Property Declared values Durable Colours: s d < 1,80 m at 23 C and 85 %RH Durable ProtectPlus: s d < 3,5 m at 23 C and 85 %RH Water vapour permeability The designer shall consider the relevant needs f ventilation, heating and EN ISO test condition B insulation to minimise condensation in service. Water permeability Incl. joints f non-ventilated applications: NPD s BR3 Hygiene, health and environment Table 3 - Perfmance - Release of dangerous substances Property Product The kit does not contain/release dangerous substances specified in TR 034, dated April 2013*), except Fmaldehyde concentration mg/ m 3. Fmaldehyde class E1 Dangerous substances The used fibres are not potential carcinogenic No biocides are used in the ROCKPANEL boards No flame retardant is used in the boards No cadmium is used in the boards. *) In addition to the specific clauses relating to dangerous substances contained in this European Assessment, there may be other requirements applicable to the products falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In der to meet the provisions of the Construction Products Regulation, these requirements need also to be complied with, when and where they apply. Table 4a - Perfmance - Design value of the axial load f mechanical fixing 8 mm Durable boards Subframe: solid wood F service class 2 (see Note ) and load-duration class Instantaneous [c] F hole diameters fixings see table 6 Property 8 mm boards Span in mm [b] X d = X k / M in N Table a fixing b board Middle / Edge / Cner in ETA screw fixing [a][e] C18/C24[d ]: 533 / 241 / [c] Design value of with the use of gaskets BR4 Safety the axial load screw fixing [a][e] C18 [d]: 284 / 241 / [c] with the use of 8 mm ROCKPANEL strips C24 [d]: 306 / 241 / 118 in use X d = X k / M nail fixing (32 mm) [e] C18 [d]: 142 / 142 / 142 EN 14592:2008+A1:2012 (E) [c] with the use of gaskets C24 [d]: 170 / 170 / 170 Rivet fixing [e] / 309 / [c] [a] with 30 : is the angle between the screw axis and the grain direction [d] Strength class EN 338 [b] see Table 7a [c] k mod = 1.10 in accdance with Table 3.1 Values of k mod DS/ EN DK NA:2010; F service class 2 [ ventilated structures protected against precipitation ] and load-duration class Instantaneous [Table 2.2 DS/ EN DK NA: ] [e] f s fixings see table 9b Note (accding to DS/ EN NA: (3)P ): Service class 2 - ventilated structures protected against precipitation, e.g. ventilated roof structures. EN :. In service class 2 the average moisture content in most softwoods will not exceed 20 %. Page 5 of 13

6 Table 4b - Perfmance - Design value of the axial load f mechanical fixing 8 mm Durable boards Subframe: solid wood F service class 3 (see Note ) and load-duration class Instantaneous [c] F hole diameters fixings see table 6 Property 8 mm boards Span in mm [b] X d = X k / M in N Table a fixing b board Middle / Edge / Cner in ETA screw fixing [a][e] C18/C24[d ]: 533 / 241 / [c] Design value of with the use of gaskets BR4 Safety the axial load screw fixing [a][e] C18 [d]: 233 / 233 / [c] with the use of 8 mm ROCKPANEL strips C24 [d]: 250 / 241 / 118 in use X d = X k / M nail fixing (32 mm) [e] C18 [d]: 116 / 116 / 116 EN 14592:2008+A1:2012 (E) [c] with the use of gaskets C24 [d]: 139 / 139 / 139 Rivet fixing [e] / 309 / [c] [a] with 30 : is the angle between the screw axis and the grain direction [d] Strength class EN 338 [b] see Table 7a [c] k mod = 0.90 in accdance with Table 3.1 Values of k mod DS/ EN DK NA:2010; F service class 3 [ External uses fully exposed ] and load-duration class Instantaneous [Table 2.2 DS / EN DK NA: ] [e] f s fixings see table 9b Note (accding to DS/ EN NA: (3)P ): Service class 3 is characterised by climatic conditions leading to higher moisture contents than in service class 2 (compare Note in Table 4a). Table 4c - Perfmance - Design value of the axial load f mechanical fixing 8 mm Durable boards Subframe: solid wood F service class 2 (see Note ) and load-duration class Permanent [c] F hole diameters fixings see table 6 Property 8 mm boards Span in mm [b] X d = X k / M in N Table a fixing b board Middle / Edge / Cner in ETA screw fixing [a][e] C18[d ]: 396 / 241 / [c] Design value of with the use of gaskets C24[d ]: 425 / 241 / 118 BR4 Safety the axial load screw fixing [a][e] C18 [d]: 155 / 155 / [c] with the use of 8 mm ROCKPANEL strips C24 [d]: 167 / 167 / 118 in use X d = X k / M nail fixing (32 mm) [e] C18 [d]: 77 / 77 / [c] with the use of gaskets C24 [d]: 93 / 93 / 93 Rivet fixing [e] / 309 / [c] [a] with 30 : is the angle between the screw axis and the grain direction [d] Strength class EN 338 [b] see Table 7a [c] k mod = 0.60 in accdance with Table 3.1 Values of k mod DS/ EN DK NA:2010; F service class 2 [ ventilated structures protected against precipitation ] and load-duration class Permanent [Table 2.2 DS / EN DK NA: ] EN 14592:2008+A1:2012 (E) [e] f s fixings see table 9b Note (accding to DS/ EN NA: (3)P ): Service class 2 - ventilated structures protected against precipitation, e.g. ventilated roof structures. EN In service class 2 the average moisture content in most softwoods will not exceed 20 %. Page 6 of 13

7 BR4 Safety in use Table 5 - Perfmance - Property Design value of the axial load X d = X k / M [c] Design value of the axial load f mechanical fixing 8 mm Durable strips f bonding purposes F service class 2 (see Note ) and load-duration class Instantaneous [c] F hole diameters fixings see table 6 Subframe: solid wood Span in mm 8 mm strips X [b] d = X k / M [c] in N Table in in combination with b adhesive SE: start / end SM: Middle of a 2 a fixing ETA ridge of the strip the strip screw fixing and intermediate C18 [d] : 266 C18 [d] : strips [a][e] C24 [d] : 266 C24 [d] : [c] screw fixing and end strips C18 [d] : 124 C18 [d] : joint strips [a][e] C24 [d] : 124 C24 [d] : [c] nail fixing (32 mm) and C18 [d] : 133 C18 [d] : intermediate strips [e] C24 [d] : 133 C24 [d] : [c] nail fixing (32 mm) and end C18 [d] : 76 C18 [d] : strips [b][e] C24 [d] : 76 C24 [d] : [c] Strips f a wooden subframe : located on vertical joints located on end between joints [a] with 30 : is the angle between the screw axis and the grain direction [b] fixed points in the middle of the length of the strip [c] k mod = 1.10 Table 3.1 DS/ EN DK NA:2010 F service class 2 [ ventilated structures protected against precipitation ] and Load-duration class Instantaneous [Table 2.2 DS/ EN DK NA: ] [d] Strength class EN 338 [e] f s fixings see table 9b a 2 a SE a 2 a SE issued on and EN 14592:2008 +A1:2012 (E) Note (accding to DS/ EN NA: (3)P ): Service class 2 ventilated structures protected against precipitation, e.g. ventilated roof structures. EN : In service class 2 the average moisture content in most softwoods will not exceed 20 % SM SM Table 6 Perfmance mechanical fixings : hole diameters f Durable boards and Durable strips in bonded applications Fixing type [a] Board dimension Fixed hole Moving hole Slotted hole considered Screw 3,2 6,0 3,4 * 6, * 3050 BR4 Safety in use Nail 2,5 3,8 2,6 * 3, * 2420 Rivet 5,2 8,0 5,2 * 8, * 3050 [a] f s fixings see table 9a and 9b Page 7 of 13

8 BR4 Safety in use [a]: [b]: Table 7a Perfmance fixings accding to table 4, 5 and 6 with the required edge distances, maximum distances and hizontal installation of boards l b / 2 M M Subframe Aluminum : l b b 2 M M: F crect fixing (SP, and SPM) a riveting tool with rivet spacer must be used (e.g. 0,3 mm). Subframe aluminum /SP [b] 'Fixed hole' and 'slotted holes' SP (accding to Tablee 6) in the middle of the vertical part of the board All the other fixingg points are moving points l m length max 3050 mm moving length 1510 mm l mv l b b 2 M [b] Fixing type Rivet [a] Screw Nail Adhesive Location oft he fixing M: middle of the board E: edge of the board C: cner of the board Length of the board max. 600 mm; b 2 in the central area of the boardd length l b Creating a fixed point by the use of o a sleeve M b max Continuously applied triangular adhesive ridge of 9 mm Drill hole accding to Table 6 Sleeve M Sleeve [a] [b] 8 mm ø8 x 7,5 drill hole ø5,1 - 'Fixed point' (accding to Table 6) in the central area of the vertical edge of the board a max a 1 C E b E M a 1 b a 1 a 2 a a 2 ETA-07/ /0141 Issued on Table 5 and fig. 8 Page 8 of 13

9 BR4 Safety in use Table 7b l b M Perfmance fixings accding to Table 4, 5 and 6 with the required edge distances, maximum distances and vertical installation of boards b 3 M l b2 b 4 l b SP SPM M SP SPM /SP [b] 'Fixed points' and 'slotted points' SP (accding to Table 6) in the middle of the vertical part of the board M [b] Fixed point realized by a sleeve M SPM [b] Slotted hole realized by a side sleeve All the other fixing points are moving points l b Length oft he board l b2 ca l b / 2 b 3 max. 400 mm max. 600 mm b 4 Issued on Table 5 and fig. 8 M: M: SPM: [a]: [b]: Subframe Aluminum : M Sleeve [a] [b] SPM Side sleeve [a] [b] Drill hole accding to Table 6 8 mm 8 mm F crect fixing (including SP, SPM, and M) a riveting tool with rivet spacer must be used (e.g. 0,3 mm). Subframe aluminum Sleeve ø8 x 7,5 hole ø5,1 ø8 x 7,5 hole ø5,1 x 6,2 BR4 Safety in use Table 8 Perfmancee shear strength mechanical fixings Fixing Characteristic shear strength Screws mechanical fixings Nails Average values Rivets Failure load 1549 N 1325 N 1722 N Defmation 9 mm 15 mm 1,7 mm issued Page 9 of 13

10 Table 9a - Specifications mechanical fixings - Rivet aluminum stainless steel [e] SFS Aluminum [d] SFS Stainless steel A4 [a] MBE Aluminum [d] MBE stainless steel [b] Code AP S SSO-D Body aluminum EN AW-5019 (AlMg5) in accdance with EN stainless steel material number in accdance with EN aluminum EN AW-5019 (AlMg5) in accdance with EN stainless steel material number in accdance with EN Mandrel stainless steel material number in accdance with EN stainless steel material number in accdance with EN stainless steel material number in accdance with EN stainless steel material number in accdance with EN Pull-out F mean,n = 2038 F mean,n = 1428 F mean,10 = 2318 F mean,10 = 3212 strength s = 95 s = 54 s = 85 s = 83 F u,5 = 1882 F u,5 = 1339 F u,5 = 2155 F u,5 = 3052 d d d 3 2,7 2,7 2,7 2,95 l k 1,5 1,5 1,5 1,5 profile aluminum t 1,5 mm steel t 1,0 mm [a] aluminum t 1,8 mm steel t 1,5 mm [b] [a] : [b]: The minimum thickness of the vertical steel profiles is 1.0 mm. The steel quality is S320GD +Z EN number ( equivalent f cold fming). F minimum coating thickness see [c] The minimum thickness of the vertical steel profiles is 1.5 mm. The steel quality is EN :2004 S235JR number F minimum coating thickness see [c] [c] : The minimum coating thickness (Z ZA) is determined by the crosion rate (amount of crosion loss in thickness per year) which depends on the specific outdo atmospheric environment (the Zinc Life Time Predict can be used to calculate the Crosion Rate in m/y f a Z coating: (copyright The International Zinc association). The coating designation (classification which determines the coating mass) shall be agreed between the contract and the building owner. Alternatively a hot dip galvanized coating accding to EN ISO 1461 can be used. [d] : The aluminum is AW-6060 accding to EN The R m /R p0,2 value is 170/140 f profile T6 and 195/150 f profile T66. [e] : F crect fixing a riveting tool with rivet spacer must be used (e.g. 0,3 mm) Page 10 of 13

11 Table 9b - Specifications mechanical fixings - Ring-shank nail 2,,7/2,9 x 32 and 2,7/2,9 x 400 mm Stainless steel in accdance with EN Material number o Definitions in accdance with EN 14592: A1:2012 d = 2,6 2,8 d 2 = 2,8 3,0 l f nail 32 = 31 32,5 l f nail 40 = 39 40,5 l 2 f nail 32 = l 2 f nail 40 = l p = 4,8 l g = l 2 - l p d h = 5,8 6,3 h t = 0,8 1,0 Tx screws 4,5 x 35 mm Stainless steel in accdance with EN Material number Definitions in accdance with EN 14592: A1:2012 d = 4,3 4,6 d s = 3,3 3,4 d h = 9,6-0,4 l = 35-1,25 l g = 26,25 28,5 BR4 Safety in use Table 10 Perfmance Tack-S adhesive and FoamTape - Initial I tensile strength Contact surfaces - Characteristic Design Rear of the board N/mm¹ N/mm¹ Tack-S Conditions: onto adhesivee [a] Partial fact f -40 C, -20 C, ProtectPlus X k = 6,94 X d = 1,735 material +23 C and Colours code 9Y X k = 8,30 X d = 2, C property M = 4 Primer 586 X k = 4,58 X d = 1,145 (tensile caused -20 C, +23 C by wind load) aluminum X and +80 C k = 5,92 X d = 1,48 ProtectPlus X k = X d = 0,73 Colours code 9Y X FoamTape +23 C k = X d = 1,17 Primer 586 X k = X d = 0,86 aluminum X k = X d = 0,47 [a] F the partial load fact F = 1,5 shall be b taken issued on Table 6 ROCKWOOL BV / ROCKPANEL Group Page 11 of 13 DECLARATION OF PERFORMANCE 0764-CPR-0238-DK-english-vs01

12 BR4 Safety in use Table 11 Perfmance Tack-S adhesive and FoamTape - Initial shear strength Partial fact Contact surfaces - f Conditions: Rear of the board Characteristic Design material onto N/mm¹ N/mm¹ property M Tack-S adhesive [a] FoamTape 40 (shear caused by permanent load) 20 (shear caused by tempary load) [a] F the partial load fact F = 1.5 shall be taken -40 C -20 C +23 C and +80 C +23 C ProtectPlus Colours code 9Y X k = 7.00 X d = Primer 586 X k = 7.69 X d = aluminum X k = 8.58 X d = ProtectPlus Colours code 9Y X k = 1.00 X d = 0.05 Primer 586 X k = 0.85 X d = 0.04 aluminum X k = 0.99 X d = 0.05 issued on Table 6 BR4 Safety in use Table 12 Perfmance Tack-S adhesive- Shear : defmation declared Contact surfaces - Rear of Defmation mm the board onto ProtectPlus and Colours Tack-S adhesive code 9Y Conditions: -20 C, +23 C aluminum and +80 C Primer Aspects of durability and serviceability Table 13 Perfmance Tack-S adhesive: Characteristic tensile strength Contact surfaces - Perfmance N/mm¹ Rear of the board onto 21 days 42 days ProtectPlus Immersion in water X k = 2.80 X k = 2.22 Colours code 9Y without UV Primer 586 X k = 5.44 X k = 4.73 aluminum X k = 3.12 X k = 2.58 [a] F the partial load fact F = 1.5 shall be taken Aspects of durability and serviceability Table 14 Perfmance Tack-S adhesive: Characteristic tensile strength Contact surfaces - Rear of the board Perfmance onto Humidity and NaCl aluminum X k = 6.03 N/mm¹ Humidity and SO 2 aluminum X k = 6.67 N/mm¹ BR4 Safety in use Table 15 Perfmance Impact resistance Panels without a hizontal joint Panels with a hizontal joint ready accessible and vulnerable to impacts Impact Energy Categy 1 J IV Steel ball 0.5 kg Hard body 3 J III, II and I Steel ball 1.0 kg 10 J II and I Soft body Ball 3 kg 10 J IV and III 60J II and I Soft body Bag 50 kg 300 J II Steel ball 0.5 kg 1 J IV Hard body Steel ball 0.5 kg 3 J III, II and I ROCKWOOL BV / ROCKPANEL Group Page 12 of 13 DECLARATION OF PERFORMANCE 0764-CPR-0238-DK-english-vs01

13 Table 16 Perfma ance dimensional stability Length Cumulative dimensional change [a]] 0,085% BR4 Safety Coefficient of thermal expansion in use 10 6 K -1 10,5 Coefficient of moisture expansion 42% 0,288 RH difference after 4 days mm/m [a] As a consequence the minimum joint width shall be 3 mm, preferably 5 mm. Width 0,084% 10,55 0,3177 ETA-07/014issued on Aspects of durability and serviceability Table 17 Resistance to hygro-thermal cycles and Xenon Arc exposure Perfmance Resistance to Hygrothermal cycles Pass Resistance to Xenonn Arc exposure Finish ISO 105 A02: EOTA TR010 climate class c S (Technical Colours/Rockclad 3-4 better Rept 010) Finish ISO 105 A02: 5000 hours artificial weathering ProtectPlus 4 better 8. The perfmance of the product identified above is in confmity with the set of declaredd perfmance/s. This declaration of perfmance is issued, in accdance with Regulation (EU) No 305/2011, under the sole responsibilityr y of the manufacturer identified above. Signed f and on behalf of the manufacturer by: ROCKWOOL B.V. W.J.E. Dumoulin Technical Direct Operations DE-NL Att Roermond, The Netherlands on 6 th February 2017 DOP in accdance with Commission Delegated Regulation (EU) No 574/2014 of 21 February 2014 amending Annex III to Regulation ( EU) No 305/20111 of the European Parliament and of the Councill on the model to be used f drawing up a declaration of perfmance on construction products, /eur-lex.europa.eu/legal-content/en/txt/?uri=celex%3a32014r0574,, OJ L 159, , p ROCKWOOL BV / ROCKPANEL Group Page 13 of 13 DECLARATION OF PERFORMANCE 0764-CPR-0238-DK-english-vs01