RF-2000 Round Fire Damper
|
|
- Kerrie Flynn
- 6 years ago
- Views:
Transcription
1 RF-2000 Round Fire Damper Installation Instructions , Rev. C Part No , Rev. C Issued March 2016 Applications The RF-2000 round fire damper is designed to operate with blade running horizontally. Dampers can be vertically or horizontally installed with the leading edge of the closed blade within the wall or floor. To ensure optimum operation and performance, the damper must be installed so it is round and free from raking. Do not compress or stretch the damper frame into the duct or opening. Mounting - Vertical or Horizontal. Minimum UL Classified Size - 6 in. (152 mm) diameter. Maximum UL Classified Size - 24 in. (610 mm) diameter. Installation Notes Use the following notes as guidelines when installing this product. 1. Opening Clearance: A square opening in wood or metal stud walls or masonry walls and floors shall be a minimum of 1 in. (25 mm) and a maximum of 2-1/2 in. (64 mm) larger than the damper diameter. A round opening in masonry walls or floors shall be a minimum of 1 in. (25 mm) and a maximum of 2-1/2 in. (64 mm) larger than the damper diameter. 2. Damper Sleeve: The sleeve is integral to the damper and shall be equal to or heavier than the gauge of the duct as described in National Fire Protection Association (NFPA) standard NFPA90A and as defined by the appropriate Sheet Metal and Air Conditioning Contractors National Association (SMACNA) duct construction standard. 3. Retaining Cinch Plates: Place retaining cinch plates around the damper sleeve and cinch against the sleeve with the screw provided on the cinching device (see Figure 1). The plates are designed to grab and hold the sleeve while mounting flush against the wall or floor, retaining the damper securely in the opening. The plates must overlap the opening a minimum of 1/2 in. (13 mm). Refer to the QuickLIT Web site for the most up-to-date version of this document. Figure 1: Retaining Cinch Plate Dimensions, in. (mm) Fasten the cinch plates to the wall or floor according to the following: Masonry Wall Cinch plate required on only one side of the wall fastened to the wall with a minimum of 1-1/4 in. (32 mm) #10 masonry screw. Masonry Floor Cinch plate required on both sides of the floor fastened to the floor with a minimum of 1-1/4 in. (32 mm) #10 masonry screw. Metal Stud Wall Cinch plate required on only one side of the wall fastened to the wall by engaging the metal stud a minimum of 1/2 in. (13 mm) with a #10 screw. RF-2000 Round Fire Damper Installation Instructions 1
2 Wood Stud Wall Cinch plate required on both sides of the wall fastened to the wall by engaging the wood stud a minimum of 1-1/2 in. (38 mm) with a #10 screw.! WARNING: Risk of Personal Injury. Do not place cinch plates in the groove. If the cinch plates are in the groove, the damper is not properly secured. An insecure damper may dislodge and fall, which may result in severe personal injury or death. AVERTISSEMENT : Risque de blessure. Ne pas placer les plaques de retenue dans la rainure. Si les plaques de retenue se trouvent dans la rainure, le registre coupe-feu n'est pas correctement fixé. Il pourrait alors sortir de son logement et de tomber, ce qui risque de provoquer des blessures graves, voire mortelles. 4. Damper Orientation: The leading edge of the blade in the closed position must be within the plane of the wall. Vertical installation is illustrated and horizontal is similar. (See Figure 3 through Figure 6.) The damper may be installed with up to a 30 degree variance of the axle being horizontal. The damper is approved with airflow in any direction. Figure 2: Blade Orientation 5. Duct/Sleeve Connections: Round breakaway connections must be used. Either a 4 in. (102 mm) wide draw band or #10 sheet metal screws spaced equally around the circumference of the ducts as follows: duct diameters of 22 in. (559 mm) and smaller three screws duct diameters over 22 in. (559 mm) to 24 in. (610 mm) five screws Note: When optional sealing of these joints is desired, the following sealants may be applied in accordance with the sealant manufacturer's instructions: Hardcast, Inc. Iron-Grip 601 sealant Precision - PA2084T ECO Duct Seal Design Polmerics - DP1010 Note: Install the damper so that it is square and free from raking. Compressing or stretching the damper frame into the duct or opening may result in failed operation and will void the warranty. IMPORTANT: Do not lift the damper using the blades or actuators. Lift or handle the damper using the frame or sleeve. Handling or lifting the damper by the blades or actuator may damage the damper and will void the warranty. Do not compress or stretch the damper frame into the duct or opening. IMPORTANT: Examine each smoke damper on a regular basis to ensure it is not rusted or blocked. In addition, test each smoke damper annually or semiannually, depending on the application, and according to the National Fire Protection Association (NFPA) standards, to ensure it will perform as intended. Exercise care to ensure that such tests are performed safely and do not cause system damage. 6. Optional Sealant of Dampers in Fire Rated Wall or Floor Openings: Following the sealant manufacturer's directions, remove dirt, grease, and moisture from the surface to be sealed. Apply a continuous bead of sealant to the location applicable to your specific installation. Approved sealant or fire stop materials: Dow Corning - 999A, Silastic 732RTV GE - RTV 108 Hilti Corporation - FS-One 3M - #M-CP 25WB+ Specified Technologies, Inc. - SpecSeal Series SSS or LCI John Manville International, Inc. - Firetemp CI Rectorseal - Metacaulk 1000, Metacaulk 350i, Biostop 500+ or Biostop 350i Do not apply sealant within the required expansion gap between the damper and the fire rated wall or floor. Press the surface of the sealant in place to dispel any air. Allow sealant to set up and become tackfree before operating the damper. 2 RF-2000 Round Fire Damper Installation Instructions
3 Note: If opening size allows for angle on one side only, then sealant shall be applied on only angle side. Nothing is required on non-angle side. Installation Diagrams Figure 3 and Figure 4 illustrate installation in 1 and 2 hour rated masonry floors and ceilings or walls. Figure 4: Masonry Installation, Side View Figure 3: Masonry Installation, 3 Dimensional (3D) view Note: Masonry walls require retaining cinch plates on only one side of the wall, as shown. Floors require retaining cinch plates on both sides of the floor. Figure 5 and Figure 6 illustrate installation within square openings in metal or wood stud framing incorporating 1 and 2 hour rated drywall partitions. Figure 5: Metal Stud Installation, 3D view RF-2000 Round Fire Damper Installation Instructions 3
4 Figure 6: Wood & Metal Stud Walls, Side View Screws must penetrate wood or metal studs. Metal stud walls require retaining cinch plates on only one side of the wall. Wood stud walls require retaining cinch plates on both sides of the wall. Recommended Framing for Openings in Wood and Metal Stud Walls 1. Frame wall openings as shown in Figure 7 and Figure Double vertical studs are not required for openings 36 in. wide x 36 in. high (914 mm x 914 mm) or smaller. 3. All construction and fasteners must meet the requirements of the appropriate wall design for local, regional, and national codes. Figure 7: Wooden Stud Wall Framing Dimensions, in. (mm) 4. Consult the authority having jurisdiction for other acceptable framing methods. Figure 8: Wood Stud Construction 4 RF-2000 Round Fire Damper Installation Instructions
5 Figure 9: Metal Stud Wall Framing Dimension, in. (mm) Figure 10: Metal Stud Construction European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact: WESTENDHOF ESSEN GERMANY 507 E MICHIGAN ST MILWAUKEE WI USA C/O CONTROLS PRODUCT MANAGEMENT NO. 22 BLOCK D NEW DISTRICT WUXI JIANGSU PROVINCE CHINA Building Efficiency 507 E. Michigan Street, Milwaukee, WI Metasys and Johnson Controls are registered trademarks of Johnson Controls, Inc. All other marks herein are the marks of their respective owners Johnson Controls, Inc. RF-2000 Round Fire Damper Installation Instructions 5 Published in U.S.A.
FC /2 Hour Curtain Fire Dampers
FC-2000 1-1/2 Hour Curtain Fire Dampers Installation Instructions 44-3521- 0, Rev. B Part No. 44-3521-0, Rev. B Issued March 2016 Applications Johnson Controls provides a 1-1/2 hour curtain fire damper
More information3900 Dr. Greaves Rd. Kansas City, MO (816) FAX (816)
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS FSD60-3 and FSD60-3M COMBINATION FIRE AND SMOKE DAMPER 3 HOUR UL555 RATED UL555S LEAKAGE CLASS 1 RATED
More information3 HOUR UL CLASSIFIED CURTAIN TYPE (D)IBD230, (D)IBD430, and (D)IBD630 FIRE DAMPERS WITH INTEGRAL SLEEVES
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS 3 HOUR UL CLASSIFIED CURTAIN TYPE (D)IBD230, (D)IBD430, and (D)IBD630 FIRE DAMPERS WITH INTEGRAL SLEEVES
More information11/2 HOUR UL CLASSIFIED CURTAIN TYPE (D)IBD2, (D)IBD2SS AND IBDT FIRE DAMPERS
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS 11/2 HOUR UL CLASSIFIED CURTAIN TYPE (D)IBD2, (D)IBD2SS AND IBDT FIRE DAMPERS APPLICATION The fire
More information11/2 HOUR UL CLASSIFIED DAMPERS WITH GRILLE MOUNTING ANGLES
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS SUPPLEMENT 11/2 HOUR UL CLASSIFIED DAMPERS WITH GRILLE MOUNTING ANGLES FOR RUSKIN (D)IBD, FD AND FSD
More informationApplication & General Notes: Installation Supplements: Safety Warning: Other Installation References: Receiving & Handling: Electrical Guidelines:
TRUE ROUND FIRE & FIRE/SMOKE DAMPER INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS R8218 FSD-RD FD(D)-RD UL/ULC File: R8218 New York BSA/MEA Listing: 79-03-M California State Fire Marshall Listing:
More information2.5" Min. Stud or Runner. 1.5" Mineral Fiber Blanket in Cavity, If Required. Wallboard. Retaining Angle. 1" Min. Damper Sleeve on 10" centers.
General Notes: When UL is referred to in this document, it represents UL/ULC. This installation instruction applies to Fire s (static, dynamic, curtain, single and multi-blade types) mounted in the plane
More informationinstallation instructions Combination Fire & Smoke Damper
Combination Fire & Smoke Damper Sleeve Fire Rated Partition Retaining Angle Combination Fire & Smoke Damper Actuator General Notes: Combination Fire & Smoke Dampers are approved for use in static or dynamic
More informationStandard Installation Fire Damper Models: 119, 119(F), 119(SS), D19
Standard Installation Fire Damper Models: 119, 119(F), 119(SS), D19 Page 1 or 8 APPLICATION This fi re damper is intended to restrict the passage of fl ame. The standard installation requires that the
More informationStandard Installation
APPLICATION Damper Models RC and RF are round, single blade, dynamically rated combination fire/smoke and fire dampers are intended to restrict the passage of flame and smoke (Model RC) or flame only (Model
More informationInstallation, Operation and Maintenance Manual
Document 483517 Curtain Fire s DFD-XXX and FD-XXX 1 1 2 and 3 Hour Curtain Fire s Vertical and Horizontal Mount Installation, Operation and Maintenance Manual Please read and save these instructions for
More informationSystem No. HW-D-0119
System No. HW-D-0119 August 03, 2007 Assembly Rating 1, 2 and 3 Hr (See Item 2) Nominal Joint Width 1 In. Class II and III Movement Capabilities 100% Compression or Extension 1. Floor Assembly The fire-rated
More informationFire Dampers (Static & Dynamic)
Fire Dampers (Static & Dynamic) Important General Notes: When UL is referred to in this document, it represents UL/ULC. This installation instruction applies to Fire Dampers (static, dynamic, curtain,
More informationRATING: Consult factory for availability Consult factory for availability
DYNAMIC FIRE DAMPER MODELS: 75A-DY (1-1/2 HR rating) APPLICATION The model 75A-DY is constructed with standard constructiongalvanized steel. 75A-DY is 1-1/2 hour UL rated dynamic damper for use in HVAC
More informationLLOYD INDUSTRIES INC. DAMPER INSTALLATION INSTRUCTIONS
Installation and Maintenance Instructions 1-1/2 Hour Rated, UL Classified model 75 fire dampers For use in fire barriers with ratings of less than 3 hours INSPECTION 1. Inspect for shipping damage. 2.
More informationInstallation, Operation and Maintenance Manual
Document 481319 Fire and Combination Fire Smoke Dampers DFDR-XXX, FDR-XXX, FSDR-XXX, SEDFDR-XXX, SEFSDR- XXX, SSDFDR-XXX, SSFDR-XXX SSFSDR-XXX Series 1 1 2 Hour Vertical and Horizontal Mount Installation,
More informationStandard Installation Combination Fire/Smoke Damper Models: FS1(SS), FS2(SS) Fire Damper Models: MD19(SS)
Standard Installation Combination Fire/Smoke Damper Models: FS1(SS), FS2(SS) Fire Damper Models: MD19(SS) Page 1 of 6 APPLICATION These dynamically rated fire/smoke and fire s are intended to restrict
More informationThis manual is the property of the owner, and is required for future maintenance. Please leave it with the owner when the job is complete.
Part Number 452763 FD, DFD, SSFD, SSDFD, & KFD Models 11/2 and 3 Hour Curtain Fire s Vertical and Horizontal Mount Installation, Operation and Maintenance Instructions FD, DFD, SSFD, & KFD models are intended
More informationRECEIVING AND HANDLING
FD and DFD 150X Series models are intended for installation in accordance with fire damper requirements established by: National Fire Protection Association NFPA Standard 90A BOCA National Building Codes
More informationfor FD & DFD 150X MODELS
Part #45946 Installation, Operation and Maintenance Instructions FD and DFD 150X Series models are intended for installation in accordance with fire damper requirements established by: National Fire Protection
More informationDocument Number FD & DFD 150X MODELS Hour Curtain Fire Dampers Vertical or Horizontal Mount
Document Number 45946 FD & DFD 150X MODELS 1 1 2 Hour Curtain Fire s Vertical or Horizontal Mount Installation, Operation and Maintenance Instructions FD and DFD 150X Series models are intended for installation
More informationDocument number CURTAIN FIRE DAMPERS
Document number 481324 CURTAIN FIRE DAMPERS DFD, DFD-150X, FD, FD-150X, SSDFD, SSFD, AND KFD Series 1 1 2 and 3 Hour Curtain Fire s Vertical and Horizontal Mount Installation, Operation and Maintenance
More informationabi air balance INSTALLATION INSTRUCTIONS FIRE/LEAKAGE RATED CORRIDOR DAMPERS MODEL FS2C250 APPLICATION INSTALLATION Wiring Diagram II-FS2C-04.
INSTALLATION INSTRUCTIONS FIRE/LEAKAGE RATED CORRIDOR DAMPERS MODEL FS2C250 II-FS2C-04.8 APPLICATION This Corridor Damper is Classified by Underwriters Laboratories for One Hour Fire Resistance and as
More informationInstallation, Operation, and Maintenance Instructions
Part Number 461337 OFSD-XXX, ODFD-XXX, OFD-XXX, and OSSFD-XXX Series 11/2 Hour Combination Fire Smoke or Curtain Fire s Out of Wall or Out of Floor Vertical or Horizontal Mount Installation, Operation,
More informationInstallation, Operation and Maintenance Manual
Document 483519 MULTI-BLADE FIRE AND COMBINATION FIRE SMOKE DAMPERS DFD-XXX and FSD-XXX 1 1 2 Hour Fire & Combination Fire Smoke s (with factory installed sleeve and actuator) Vertical and Horizontal Mount
More informationDivision 07 Thermal and Moisture Protection Thermal Protection Blanket Insulation Page 1 of 11
07 21 16 Blanket Insulation Page 1 of 11 Unifrax I LLC Design No. UNI/BI 120-14 FIRE RESISTANT GREASE DUCT FyreWrap Elite 1.5 Duct Insulation ASTM E 2336-16 and ICC-ES Acceptance Criteria for Grease Duct
More informationDocument GRILLE ACCESS OUT OF WALL OR OUT OF FLOOR COMBINATION FIRE SMOKE DAMPERS
Document 472477 GRILLE ACCESS OUT OF WALL OR OUT OF FLOOR COMBINATION FIRE SMOKE DAMPERS GFSD-XXX SERIES 1 1 2 Hour Combination Fire Smoke Dampers Vertical and Horizontal Mount Installation, Operation
More informationDocument OUT OF WALL FIRE AND COMBINATION FIRE SMOKE DAMPERS
Document 461337 OUT OF WALL FIRE AND COMBINATION FIRE SMOKE DAMPERS ODFD-XXX, OFD-XXX, OFSD-XXX SERIES 1 1 2 Hour Fire & Combination Fire Smoke Dampers Out of Wall or Out of Floor Vertical and Horizontal
More informationBASIC LOUVER INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
BASIC LOUVER INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS The following installation instructions apply to all regular stationary and operable louvers fabricated out of extruded aluminum or steel.
More informationDocument MULTI-BLADE FIRE AND COMBINATION FIRE SMOKE DAMPERS
Document 481318 MULTI-BLADE FIRE AND COMBINATION FIRE SMOKE DAMPERS DFD-XXX, DFDAF-XXX, FSD-XXX, FSD-XXXV, IMO-XXX,SEDFD-XXX, SEFSD-XXX, AND SSFSD-XXX 1 1 2 and 3 Hour Fire & Combination Fire Smoke s (with
More informationInstallation, Operation and Maintenance Manual
Document 461335 Corridor Ceiling Dampers CFSD-xxx SERIES (with factory installed sleeve and actuator) Installation, Operation and Maintenance Manual Please read and save these instructions for future reference.
More informationDivision 07 Thermal and Moisture Protection Thermal Protection Blanket Insulation Page 1 of 17
07 21 16 Blanket Insulation Page 1 of 17 Design Number UNI/BI 120-03 FIRE RESISTANT GREASE DUCT Unifrax I LLC FyreWrap Elite 1.5 Duct Insulation CAN/ULC S144 Fire Resistance Rating 2 hours Fire Inside
More informationSAUDI AIR CONTROL SYSTEM INDUSTRIAL REGISTRATION NO.353 FIRE DAMPERS
SAUDI AIR CONTROL SYSTEM INDUSTRIAL REGISTRATION NO.353 FIRE DAMPERS FIRE DAMPERS OUTSTANDING FEATURES: Gravity operated for vertical installation and with closure springs and latches for horizontal installation.
More informationTypical Actuator. RRL Control Device Standard
Part Number 461336 FSD-XXX, DFD-XXX, DFDTF-XXX CFSD-XXX, SEDFD-XXX, SEFSD-XXX, IMO-XXX, and SSFSD-XXX Series 1 1 2 and 3 Hour Fire & Combination Fire Smoke s (with factory installed sleeve and actuator)
More informationDocument Number FD, DFD, SSFD, SSDFD, & KFD Models 11/2 and 3 Hour Curtain Fire Dampers Vertical and Horizontal Mount
Document Number 452763 FD, DFD, SSFD, SSDFD, & KFD Models 11/2 and 3 Hour Curtain Fire s Vertical and Horizontal Mount Installation, Operation and Maintenance Instructions FD, DFD, SSFD, & KFD models are
More informationSECTION FIRESTOP SYSTEMS
SECTION 07 84 00 FIRESTOP SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationINSTALLATION INSTRUCTION BOOKLET FOR CURTAIN FIRE DAMPERS
INSTALLATION INSTRUCTION BOOKLET FOR CURTAIN FIRE DAMPERS Instructions included in this booklet: IOM # Description Page(s) 452763 FD, DFD, SSFD & KFD Models 2 9 453946 FD & DFD 150X Models 10 17 462721
More informationDuct Wrap Flexible Wraps
Design No. 3MU/ 60-01 December 23, 2010 VENTILATION DUCT PROTECTION 3M Company 3M Fire Barrier Duct Wraps: 615 and 615+ 3M Fire Barrier Sealants: Water-Tight 1000-NS Silicone, Water-Tight 1003-SL Silicone
More informationRECEIVING AND HANDLING INSTALLATION SUPPLEMENTS WARRANTY SAFETY WARNING:
Typical Actuator RRL Control Device Standard Part #461336 Installation, Operation and Maintenance Instructions for FSD-XXX, DFD-XXX, CFSD-XXX, SSFSD-XXX SERIES 1 1 2 and 3 Hour Fire & Combination Fire
More informationStandard Installation Ceiling Radiation Dampers Models: 289, RCU, L89, A89, 291, RCI, L91, A91, 293, RC4, L93, A93, 295, RDU, L95, A95, 297, RDI,
Page of 6 Standard Installation Ceiling Radiation Dampers Models: 289, RCU, L89, A89, 29, RCI, L9, A9, 293, RC4, L93, A93, 295, RDU, L95, A95, 297, RDI, APPLICATION These ceiling radiation dampers provide
More informationNATIONAL GYPSUM COMPANY Wood Frame Walls And Ceilings Single- And Double-Layer Construction
Walls And Ceilings Single- And Double-Layer Construction 09 9 00/NGC Single-Layer Construction The single-layer construction system consists of a single layer of Gold Bond brand Gypsum Board applied to
More informationCERTIFICATE OF APPROVAL No CF 5073 LEMINAR AIR CONDITIONING INDUSTRIES L.L.C.
CERTIFICATE OF APPROVAL No CF 5073 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of PO Box 33539, Dubai,
More informationSLOTTED STUD WIND-LOAD & NON-LOAD BEARING DEFLECTION WALL SYSTEM. U.L. FIRE RATED Head-of-Wall Joint Systems
SLOTTED STUD WIND-LOAD & NON-LOAD BEARING DEFLECTION WALL SYSTEM U.L. FIRE RATED Head-of-Wall Joint Systems 1-800-275-2279 STEELER INC. SLOTTED STUD 1-800-275-2279 The STEELER SLOTTED STUD is an innovative
More informationTRUERH Series HT-670x Humidity Transmitters
24 7701 187, Rev. B Installation Instructions HT670x Issue Date March 2016 TRUERH Series HT670x Humidity Transmitters Application Requirements Configure the transmitter for the output signal required prior
More informationFIRESTOP SUBMITTAL PACKAGE
FIRESTOP SUBMITTAL PACKAGE HVAC Materials FS-ONE Intumesent Caulk CP 606 Acrylic Includes: Technical and Installation Data UL Certificate of Compliance LEED information MSDS UL Details Concrete Assemblies
More informationLouvers and Dampers April Product Guide Specification SECTION SMOKE DAMPERS
Louvers and Dampers April 2008 P.O. Box 606 7435 Industrial Road Florence, Kentucky, 41042 Phone: (859) 647-2299 Fax: (859) 647-7810 Web Site: www.louvers-dampers.com Product Guide Specification SECTION
More informationSystem No. C-AJ-8133
System No. C-AJ-8133 March 09, 2011 F Ratings - 1, 1-1/2, 2 and 3 Hr (See Item 2) T Ratings - 0, 1/2, 3/4, 1, 1-1/2, 2 and 3 Hr (See Item 2) 1. Floor or Wall Assembly Min 4-1/2 in. (114 mm) thick reinforced
More informationFIRESTOP SUBMITTAL PACKAGE
FIRESTOP SUBMITTAL PACKAGE HVAC Materials FS-ONE Intumesent Caulk CP 606 Acrylic Includes: Technical and Installation Data UL Certificate of Compliance LEED information MSDS UL Details Concrete Assemblies
More informationWEIGHT PER PIECE (LBS.)
PRODUCT DESCRIPTION DATA SHEET 04 73 19-US BASIC USE ProGUARD DP is intended to be installed over sheathing and waterproofing over steel or wood studs or over concrete masonry units or poured concrete
More informationHOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL
13686.00 HOLLOW METAL DOORS AND FRAMES 081113-1 SECTION 081113 - HOLLOW METAL DOORS AND FRAMES 1.1 RELATED DOCUMENTS: PART 1 - GENERAL A. Drawings and general provisions of Contract, including General
More informationSpecial Applications. Dorn Equipment, Corporation 27 Upham Street Melrose, MA Phone: Fax:
Special Applications Outdoor Protection When using the FIRSTO units outdoors, or wherever vapor or moisture barrier is needed, an application of FIWA sealant is used. The sealant should be applied to any
More informationEHH-601D. Miami-Dade Qualified Wind-Driven Rain Louver
Application and Design is a Florida Product Approved and Miami-Dade Qualified stationary horizontal blade wind driven rain extruded aluminum louver designed to protect air intake and exhaust openings in
More informationRSIC-V. Acoustical Surfaces, Inc. RSIC-V Sound Isolation Clip RSIC V INSTALLATION GUIDE. We Identify and S.T.O.P. Your Noise Problem
A Master Distributor for PAC INTERNATIONAL, INC. RSIC V INSTALLATION GUIDE RSIC-V Page 1 Furring Channel: Minimum requirements: 25 gauge, hemmed edge detail required on all 25 gauge furring channel. Meets
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws caulking gun shims tape measure 1/8 drill bit Phillips screw driver cardboard china marker (or grease pencil) furring strips
More informationInstallation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
Installation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86 inch Weight....025 lbs Max Spacing...48
More informationInstruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
SOUND ISOLATION CLIPS Installation Manual Instruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86
More informationDSC BUILDING 1200 ALTERATIONS OCTOBER 2011 SECTION DUCT INSULATION
SECTION 230713 DUCT INSULATION PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 233113 Ductwork and Accessories 1.2 REFERENCES A. American Society for Testing and Materials (ASTM): 1. E84-96a Test Method
More informationIntumescent Fire Dampers
Fire tested and for up to 2 hours fire integrity in plasterboard, concrete or masonry and in steel duct spigots walls and floors Approved to AS1530.4 Technical Data Sheet KEY BENEFITS - 2 hours fire rating
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking (See specific caulking recommendations) caulking gun shims tape measure 1/8 drill bit Phillips screw driver
More informationFollowing contains common verbiage found in major model building codes and has been edited for the purpose of inclusion on this CD.
Following contains common verbiage found in major model building codes and has been edited for the purpose of inclusion on this CD. Included are selected sections of codes taken directly from: 1997 Uniform
More informationADC. The Greenbook of Flex. Flexible Duct Performance & Installation Standards (5 th Edition) Characteristics of flexible duct
ADC Flexible Duct Performance & Installation Standards (5 th Edition) The Greenbook of Flex Provides information about Characteristics of flexible duct Testing, Listing, Reporting, and Certifying Installation
More informationINSTALLATION MANUAL. METAL INSULATED PANELS -ROXUL -Expanded Polystyrene
INSTALLATION MANUAL METAL INSULATED PANELS -ROXUL -Expanded Polystyrene Insulated Metal Panels London Eco-Metal Manufacturing Inc. **Also see Eco-Metal s Handling Manual** These instructions are provided
More informationRSIC-1-INSTALALTION GUIDE RSIC-1 SOUND ISOLATION CLIP
RSIC-1 Drywall Furring Channel: Minimum Requirements: 25 gauge, hemmed edge detail required on all 25 gauge furring channel. Meets or exceeds SFIA requirements. Depth: 7/8 inch Width Bottom: 2-9/16 to
More informationFyreWrap Elite 1.5 Duct Insulation Air Distribution System (ADS Ducts)
Product Information Sheet FyreWrap Elite 1.5 Duct Insulation Air Distribution System (ADS Ducts) Introduction Unifrax s FyreWrap Elite 1.5 Duct Insulation is a singlelayer flexible duct wrap enclosure
More informationSt. Monica Food Pantry
St. Monica Food Pantry 07 8400-1 SECTION 07 8400 - FIRESTOPPING PART 1 - GENERAL 1.1 SUMMARY: A. Related work: 1. Concrete. 2. Mortar and grout. 3. Brick masonry. 4. Concrete unit masonry. 5. Structural
More informationInstallation, Operation and Maintenance Manual
Document 474644 EHH-601D Channel Installation with VCD-40 Damper Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: MINERAL FIBER FIREPROOFING REPORT HOLDER: UNIFRAX I LLC
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2224 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 07 00
More informationFastWrap+ 1 1 /2 Commercial Kitchen Grease Duct Air Ventilation Duct
FastWrap+ 1 1 /2 Commercial Kitchen Grease Duct Air Ventilation Duct Fire Protection Systems Product Data and Installation Guide NFPA 96 IMC 1. Product Description - New and Improved FastWrap+ Thermal
More information2500 Series Fire Smoke Dampers
General Description The model 2550 is designed to prevent the spread of fire and smoke through ventilation ductwork in walls and floors. From receiving an alarm the power to the damper actuator is removed
More informationDesign No. HI/BP PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table 1
FIRESTOP JOINT SPRAY CFS-SP WB SILICONE JOINT SPRAY CFS-SP SIL F-RATING 2-HR. 2-HR. T-RATING -HR. -HR. APPLICATION THICKNESS PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table /8" WET FILM (/6"
More informationProduct Information Sheet
Product Information Sheet FyreWrap Elite 1.5 Duct Insulation Air Distribution System (ADS Ducts) Introduction Unifrax s FyreWrap Elite 1.5 Duct Insulation is a singlelayer flexible duct wrap enclosure
More informationINSTALLATION MANUAL SURFACE-MOUNTED HEADWALL
INSTALLATION MANUAL SURFACE-MOUNTED HEADWALL Model # Series 7200-S Top Mounting Plate Electrical Junction Box Located Behind Removable Upper Panel Medical Gas Connections Lower Mounting Plate OVERVIEW
More informationSECTION FIRE RESISTIVE JOINT SYSTEMS
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 07 84 43 FIRE RESISTIVE JOINT SYSTEMS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationBRANZ FACTS RESILIENT NON-STRUCTURAL ELEMENTS SEISMICALLY RESILIENT NON-STRUCTURAL ELEMENTS # 3. Restraint systems
SEISMICALLY BRANZ FACTS RESILIENT NON-STRUCTURAL ELEMENTS SEISMICALLY RESILIENT DESIGN CRITERIA # 2 NON-STRUCTURAL ELEMENTS # 3 Restraint systems The next step in the non-specific design pathway in NZS
More informationFire Barrier Duct Wrap 615+
Fire Barrier Duct Wrap 615+ Duct Wrap Fire Protection System for Commercial Kitchen Grease and Ventilation Air Ducts Product Data Batts and blankets for use in fire resistive duct assemblies see UL fire
More informationSECTION GYPSUM BOARD PART 1 - GENERAL
SECTION 09250 - GYPSUM BOARD PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More information6032 SH 3P Residential Shower Installation Instructions Gelcoat & Solid Surface Bathware
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking caulking gun acrylic latex caulk shims tape measure 1/8 drill bit Phillips screw driver cardboard china
More informationTechnical Data Sheet
Technical Data Sheet ProGUARD Concrete Insulated Sheathing Specifications & Installation Table Of Contents Product Description... pg. 1 Basic Use... pg. 1 Exterior Finishes... pg. 1 Standard Sizes... pg.
More informationa 3 CeramicSteel Sans Technical Guide
4 3 2 PolyVision a 3 CeramicSteel Sans Technical Guide #2 PHILLIPS PolyVision Americas 10700 Abbotts Bridge Rd. Suite 100 Johns Creek, GA 30097 USA Tel. 1-888-325-6351 info@polyvision.com PolyVision Europe
More informationINSTALLATION MANUAL RECTANGULAR COLUMN
INSTALLATION MANUAL RECTANGULAR COLUMN Model # 5502 OVERVIEW The Rectangular Column is a UL-listed, multi-sided, vertical hospital modular service assembly. This system uses vertical and/or horizontal
More informationC. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPRODUCT DATA SHEET Metacaulk BOX GUARD Classified under Wall Opening Protective Material as found in UL's Fire Resistance Directory
PRODUCT DATA SHEET Metacaulk BOX GUARD Classified under Wall Opening Protective Material as found in UL's Fire Resistance Directory January 2011 1. Product Description Metacaulk BOX GUARD is a one component
More informationPARKING PLAZA MEXICO COVERED GAS PUMP ISLAND PARKING BUS PARKING AREA. The Evans Group COVERD AREA TACO STAND COVERD AREA AREA FREEZER EXIT EXIT
OFFICE FUEL ISLAND ATTENDANTS OFFICE GAS PUMP ISLAND BUS SIGNAGE AND 6'-0" WALL TACO STAND COVERED RESTROOMS RESTROOMS MARKET TACO STAND PLAZA MEXICO COVERED FREEZER GAS PUMP ISLAND BUS FUEL ISLAND ATTENDANTS
More informationPRESTON HEALTH SERVICES ARCHITECT S NO. 2700
SECTION 23 0510 - BASIC MATERIALS AND METHODS PART 1 - GENERAL 1.1 DESCRIPTION OF WORK: A. Provide equipment, labor, materials, etc. required to make a complete working installation as shown or as specified.
More informationInstallation Guide and Safety Manual Resilmount A237R (Resilient Sound Isolation Clips)
Installation Guide and Safety Manual Resilmount A237R (Resilient Sound Isolation Clips) 3" RESILMOUNT A237R SPECIFICATIONS 1d " f" Width...1.375 inch Height...3.25 inch Depth...1.125 inch Weight....025
More informationFire Barrier. Moldable Putty+ Pads Protecting Metallic and Non-Metallic Electrical Boxes
3 Fire Barrier Moldable Putty+ Pads Protecting Metallic and Non-Metallic Electrical Boxes This information brochure highlights requirements for UL listed, fire-rated electrical boxes located in some UL
More informationSystem No. HW-D-0548
System No. Ì73hwdÇ%P+11bÎ ANSI/UL2079 Assembly atings - 1 and 2 Hr (See Item 2) Maximum Joint Width - 3/4, 1 or 1-1/2 In. (See Item 3) Class II Movement Capabilities - 50 or 100 %Compression or Extension
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: MINERAL-FIBER FIREPROOFING REPORT HOLDER: THERMAL CERAMICS, INC.
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2213 Reissued 04/2018 This report is subject to renewal 04/2019. DIVISION: 07 00
More informationI-STUD Shaftwall System
I-STUD Shaftwall System Summit Tower I-Stud and CertainTeed Shaftliner TM MILL CERTIFIED Steel-Con 00% GALVANIZED Steel Construction Systems UL Evaluation Report No. ER3660-02 Intertek The I-Stud is approved
More information3M CS-195+ Composite Sheet Product Description
Product Data Sheet 3M Product Description 3M Fire Barrier is a one-part composite system comprised of four components. The heart of the system is an organic/ inorganic, fire-resistive elastomeric sheet.
More informationHILTI CFS-SL / CP 653 / SPEED SLEEVE / FIRESTOP SLEEVE FIRE RATED COLLARS. Product. Scope. Building Regulations. Appraisal No.
HILTI CFS-SL / CP 653 / SPEED SLEEVE / FIRESTOP SLEEVE FIRE s Technical Assessments of products for building and construction. Hilti (New Zealand) Limited P O Box 112-030 Penrose Auckland 1642 Tel: 0800
More informationInstallation Instructions
Installation Instructions SAVE THESE INSTRUCTIONS Please read this entire manual before you install and use your room heater. Failure to follow instructions may result in property damage, bodily injury,
More informationJAMISON SOUND DOOR SPECIFICATIONS VERTICAL SLIDING SOUND REDUCTION DOOR - STC 53 POWERED OPERATION
JAMISON SOUND DOOR SPECIFICATIONS VERTICAL SLIDING SOUND REDUCTION DOOR - STC 53 POWERED OPERATION PART 1 - GENERAL 1.1 APPLICABLE PUBLICATIONS: The publications listed below form a part of this specification
More informationVoie Romaine F Maizières-lès-Metz Tel.: +33 (0) Fax.: +33 (0) Operating vacuum pressure: - 500Pa
Voie Romaine F-57280 Maizières-lès-Metz Tel.: +33 (0)3 87 51 11 11 Fax.: +33 (0)3 87 51 10 58 CLASSIFICATION REPORT CLASSIFICATION REPORT no. 09 - A - 363 According to standards EN 15650: 2010 and EN 13501-3:
More informationCS-195+ Composite Sheet FR Board
CS-195+ Composite Sheet FR Board Durable, Steel-lined Fire-Rated Board for up to 4 hours fire protection Tested to AS1530.4, EN1366 and UL Listed Technical Data Sheet a product Light. Strong. Durable.
More informationProduct Information Sheet. FyreWrap 1.5 Duct Insulation. Introduction. Product Components. Typical Product Parameters
Product Information Sheet FyreWrap 1.5 Duct Insulation Introduction FyreWrap 1.5 Duct Insulation from Unifrax is a hightemperature insulation blanket specifically designed to provide a flexible enclosure
More informationPre-Installation See detail page for general notes concerning trim accessories, holes, fasteners, gaskets, caulking and support columns.
Pre-Installation See detail page for general notes concerning trim accessories, holes, fasteners, gaskets, caulking and support columns. Assembly of Acoustical Panels Instructions to be utilized with corresponding
More informationASF FR Board PRO RANGE Coated Mineral Wool Board for the Professional
Technical Data Sheet Version: 1 Revision Date: 11-04-2011 Description ASF FR Board has been designed to maintain the fire resistance of separating walls and floors where they are breached by single or
More informationFIRE STATION 55 June 14, 2010
SECTION 15250 MECHANICAL INSULATION PART 1 - GENERAL 1.01 DESCRIPTION A. Work Includes 1. Insulation of Domestic Water Piping. 2. Pipe Insulation of refrigerant piping. 3. Insulation of ductwork. 4. Aluminum
More informationDIBD2SS CURTAIN TYPE DYNAMIC FIRE DAMPERS 1 1 / 2 HOUR UL555 RATED FOR USE IN DYNAMIC OR STATIC SYSTEMS
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FX (816) 765-8955 DID2SS CURTIN TYPE DYNMIC FIRE DMPERS 1 1 / 2 OUR UL555 RTED FOR USE IN DYNMIC OR STTIC SYSTEMS PPLICTION Ruskin Model DID2SS
More information